[ Upstream commit e13757f524 ]
Like on the Acer Switch 10 SW5-012, the Acer Switch V 10 SW5-017's _LID
method messes with home- and power-button GPIO IRQ settings, causing an
IRQ storm.
Add a quirk entry for the Acer Switch V 10 to the dmi_use_low_level_irq[]
DMI quirk list, to use low-level IRQs on this model, fixing the IRQ storm.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e9ada1d0e ]
It seems that the Windows drivers for the ACPI0011 soc_button_array
device use low level triggered IRQs rather then using edge triggering.
Some ACPI tables depend on this, directly poking the GPIO controller's
registers to clear the trigger type when closing a laptop's/2-in-1's lid
and re-instating the trigger when opening the lid again.
Linux sets the edge/level on which to trigger to both low+high since
it is using edge type IRQs, the ACPI tables then ends up also setting
the bit for level IRQs and since both low and high level have been
selected by Linux we get an IRQ storm leading to soft lockups.
As a workaround for this the soc_button_array already contains
a DMI quirk table with device models known to have this issue.
Add a module parameter for this so that users can easily test if their
device is affected too and so that they can use the module parameter
as a workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e37cc624 ]
On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.
On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.
To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().
This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 038ee49fef ]
RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():
omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS. If RTS uses active-low polarity, it is now asserted
for no reason.
The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register. That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).
(up->mcr is not, as one might think, a cache of the MCR register's
current value. Rather, it only caches a single bit of that register,
the AFE bit. And it only does so if the UART supports the AFE bit,
which OMAP does not. For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)
Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().
So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx(). Avoid by using a read-modify-write
when setting TCRTLR.
While at it, drop a redundant initialization of up->mcr. As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c. (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c919b619b ]
When noevents is true and small buffer is used the allocated memory for
holding the data may be smaller than the hard-coded 64 bytes. This can
cause the iio_generic_buffer to crash.
Following was recorded on beagle bone black with v6.0 kernel and the
digit fix patch:
https://lore.kernel.org/all/Y0f+tKCz+ZAIoroQ@dc75zzyyyyyyyyyyyyycy-3.rev.dnainternet.fi/
using valgrind;
==339== Using Valgrind-3.18.1 and LibVEX; rerun with -h for copyright info
==339== Command: /iio_generic_buffer -n kx022-accel -T0 -e -l 10 -a -w 2000000
==339== Parent PID: 307
==339==
==339== Syscall param read(buf) points to unaddressable byte(s)
==339== at 0x496BFA4: read (read.c:26)
==339== by 0x11699: main (iio_generic_buffer.c:724)
==339== Address 0x4ab3518 is 0 bytes after a block of size 160 alloc'd
==339== at 0x4864B70: malloc (vg_replace_malloc.c:381)
==339== by 0x115BB: main (iio_generic_buffer.c:677)
Fix this by always using the same size for reading as was used for
data storage allocation.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/Y0kMh0t5qUXJw3nQ@dc75zzyyyyyyyyyyyyycy-3.rev.dnainternet.fi
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4dbd6a3e90 upstream.
Current code re-calculates the size after aligning the starting and
ending physical addresses on a page boundary. But the re-calculation
also embeds the masking of high order bits that exceed the size of
the physical address space (via PHYSICAL_PAGE_MASK). If the masking
removes any high order bits, the size calculation results in a huge
value that is likely to immediately fail.
Fix this by re-calculating the page-aligned size first. Then mask any
high order bits using PHYSICAL_PAGE_MASK.
Fixes: ffa71f33a8 ("x86, ioremap: Fix incorrect physical address handling in PAE mode")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/1668624097-14884-2-git-send-email-mikelley@microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50bcceb772 upstream.
pm_save_spec_msr() keeps a list of all the MSRs which _might_ need
to be saved and restored at hibernate and resume. However, it has
zero awareness of CPU support for these MSRs. It mostly works by
unconditionally attempting to manipulate these MSRs and relying on
rdmsrl_safe() being able to handle a #GP on CPUs where the support is
unavailable.
However, it's possible for reads (RDMSR) to be supported for a given MSR
while writes (WRMSR) are not. In this case, msr_build_context() sees
a successful read (RDMSR) and marks the MSR as valid. Then, later, a
write (WRMSR) fails, producing a nasty (but harmless) error message.
This causes restore_processor_state() to try and restore it, but writing
this MSR is not allowed on the Intel Atom N2600 leading to:
unchecked MSR access error: WRMSR to 0x122 (tried to write 0x0000000000000002) \
at rIP: 0xffffffff8b07a574 (native_write_msr+0x4/0x20)
Call Trace:
<TASK>
restore_processor_state
x86_acpi_suspend_lowlevel
acpi_suspend_enter
suspend_devices_and_enter
pm_suspend.cold
state_store
kernfs_fop_write_iter
vfs_write
ksys_write
do_syscall_64
? do_syscall_64
? up_read
? lock_is_held_type
? asm_exc_page_fault
? lockdep_hardirqs_on
entry_SYSCALL_64_after_hwframe
To fix this, add the corresponding X86_FEATURE bit for each MSR. Avoid
trying to manipulate the MSR when the feature bit is clear. This
required adding a X86_FEATURE bit for MSRs that do not have one already,
but it's a small price to pay.
[ bp: Move struct msr_enumeration inside the only function that uses it. ]
Fixes: 73924ec4d5 ("x86/pm: Save the MSR validity status at context setup")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/c24db75d69df6e66c0465e13676ad3f2837a2ed8.1668539735.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaa65d17ee upstream.
Support for the TSX control MSR is enumerated in MSR_IA32_ARCH_CAPABILITIES.
This is different from how other CPU features are enumerated i.e. via
CPUID. Currently, a call to tsx_ctrl_is_supported() is required for
enumerating the feature. In the absence of a feature bit for TSX control,
any code that relies on checking feature bits directly will not work.
In preparation for adding a feature bit check in MSR save/restore
during suspend/resume, set a new feature bit X86_FEATURE_TSX_CTRL when
MSR_IA32_TSX_CTRL is present. Also make tsx_ctrl_is_supported() use the
new feature bit to avoid any overhead of reading the MSR.
[ bp: Remove tsx_ctrl_is_supported(), add room for two more feature
bits in word 11 which are coming up in the next merge window. ]
Suggested-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/de619764e1d98afbb7a5fa58424f1278ede37b45.1668539735.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05311ce954 upstream.
It is valid to receive external interrupt and have broken IDT entry,
which will lead to #GP with exit_int_into that will contain the index of
the IDT entry (e.g any value).
Other exceptions can happen as well, like #NP or #SS
(if stack switch fails).
Thus this warning can be user triggred and has very little value.
Cc: stable@vger.kernel.org
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221103141351.50662-10-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed129ec905 upstream.
While not obivous, kvm_vcpu_reset() leaves the nested mode by clearing
'vcpu->arch.hflags' but it does so without all the required housekeeping.
On SVM, it is possible to have a vCPU reset while in guest mode because
unlike VMX, on SVM, INIT's are not latched in SVM non root mode and in
addition to that L1 doesn't have to intercept triple fault, which should
also trigger L1's reset if happens in L2 while L1 didn't intercept it.
If one of the above conditions happen, KVM will continue to use vmcb02
while not having in the guest mode.
Later the IA32_EFER will be cleared which will lead to freeing of the
nested guest state which will (correctly) free the vmcb02, but since
KVM still uses it (incorrectly) this will lead to a use after free
and kernel crash.
This issue is assigned CVE-2022-3344
Cc: stable@vger.kernel.org
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20221103141351.50662-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f53af4285d upstream.
During proactive reclaim, we sometimes observe severe overreclaim, with
several thousand times more pages reclaimed than requested.
This trace was obtained from shrink_lruvec() during such an instance:
prio:0 anon_cost:1141521 file_cost:7767
nr_reclaimed:4387406 nr_to_reclaim:1047 (or_factor:4190)
nr=[7161123 345 578 1111]
While he reclaimer requested 4M, vmscan reclaimed close to 16G, most of it
by swapping. These requests take over a minute, during which the write()
to memory.reclaim is unkillably stuck inside the kernel.
Digging into the source, this is caused by the proportional reclaim
bailout logic. This code tries to resolve a fundamental conflict: to
reclaim roughly what was requested, while also aging all LRUs fairly and
in accordance to their size, swappiness, refault rates etc. The way it
attempts fairness is that once the reclaim goal has been reached, it stops
scanning the LRUs with the smaller remaining scan targets, and adjusts the
remainder of the bigger LRUs according to how much of the smaller LRUs was
scanned. It then finishes scanning that remainder regardless of the
reclaim goal.
This works fine if priority levels are low and the LRU lists are
comparable in size. However, in this instance, the cgroup that is
targeted by proactive reclaim has almost no files left - they've already
been squeezed out by proactive reclaim earlier - and the remaining anon
pages are hot. Anon rotations cause the priority level to drop to 0,
which results in reclaim targeting all of anon (a lot) and all of file
(almost nothing). By the time reclaim decides to bail, it has scanned
most or all of the file target, and therefor must also scan most or all of
the enormous anon target. This target is thousands of times larger than
the reclaim goal, thus causing the overreclaim.
The bailout code hasn't changed in years, why is this failing now? The
most likely explanations are two other recent changes in anon reclaim:
1. Before the series starting with commit 5df741963d ("mm: fix LRU
balancing effect of new transparent huge pages"), the VM was
overall relatively reluctant to swap at all, even if swap was
configured. This means the LRU balancing code didn't come into play
as often as it does now, and mostly in high pressure situations
where pronounced swap activity wouldn't be as surprising.
2. For historic reasons, shrink_lruvec() loops on the scan targets of
all LRU lists except the active anon one, meaning it would bail if
the only remaining pages to scan were active anon - even if there
were a lot of them.
Before the series starting with commit ccc5dc6734 ("mm/vmscan:
make active/inactive ratio as 1:1 for anon lru"), most anon pages
would live on the active LRU; the inactive one would contain only a
handful of preselected reclaim candidates. After the series, anon
gets aged similarly to file, and the inactive list is the default
for new anon pages as well, making it often the much bigger list.
As a result, the VM is now more likely to actually finish large
anon targets than before.
Change the code such that only one SWAP_CLUSTER_MAX-sized nudge toward the
larger LRU lists is made before bailing out on a met reclaim goal.
This fixes the extreme overreclaim problem.
Fairness is more subtle and harder to evaluate. No obvious misbehavior
was observed on the test workload, in any case. Conceptually, fairness
should primarily be a cumulative effect from regular, lower priority
scans. Once the VM is in trouble and needs to escalate scan targets to
make forward progress, fairness needs to take a backseat. This is also
acknowledged by the myriad exceptions in get_scan_count(). This patch
makes fairness decrease gradually, as it keeps fairness work static over
increasing priority levels with growing scan targets. This should make
more sense - although we may have to re-visit the exact values.
Link: https://lkml.kernel.org/r/20220802162811.39216-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 512c5ca01a upstream.
When extending segments, nilfs_sufile_alloc() is called to get an
unassigned segment, then mark it as dirty to avoid accidentally allocating
the same segment in the future.
But for some special cases such as a corrupted image it can be unreliable.
If such corruption of the dirty state of the segment occurs, nilfs2 may
reallocate a segment that is in use and pick the same segment for writing
twice at the same time.
This will cause the problem reported by syzkaller:
https://syzkaller.appspot.com/bug?id=c7c4748e11ffcc367cef04f76e02e931833cbd24
This case started with segbuf1.segnum = 3, nextnum = 4 when constructed.
It supposed segment 4 has already been allocated and marked as dirty.
However the dirty state was corrupted and segment 4 usage was not dirty.
For the first time nilfs_segctor_extend_segments() segment 4 was allocated
again, which made segbuf2 and next segbuf3 had same segment 4.
sb_getblk() will get same bh for segbuf2 and segbuf3, and this bh is added
to both buffer lists of two segbuf. It makes the lists broken which
causes NULL pointer dereference.
Fix the problem by setting usage as dirty every time in
nilfs_sufile_mark_dirty(), which is called during constructing current
segment to be written out and before allocating next segment.
[chenzhongjin@huawei.com: add lock protection per Ryusuke]
Link: https://lkml.kernel.org/r/20221121091141.214703-1-chenzhongjin@huawei.com
Link: https://lkml.kernel.org/r/20221118063304.140187-1-chenzhongjin@huawei.com
Fixes: 9ff05123e3 ("nilfs2: segment constructor")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reported-by: <syzbot+77e4f0...@syzkaller.appspotmail.com>
Reported-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b44c0e7fef ]
The functions stop_active_transfers and ep_disable are both calling
remove_requests. This functions in both cases will giveback the requests
with status ESHUTDOWN, which also represents an physical disconnection.
For ep_disable this is not true. This patch adds the status parameter to
remove_requests and sets the status to ECONNRESET on ep_disable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: f90f5afd50 ("usb: dwc3: gadget: Clear ep descriptor last")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff5a19909b upstream.
We face some regressions on a few IXP42x systems when
accessing flash, the following unrelated error prints
appear from the PCI driver:
ixp4xx-pci c0000000.pci: PCI: abort_handler addr = 0xff9ffb5f,
isr = 0x0, status = 0x22a0
ixp4xx-pci c0000000.pci: imprecise abort
(...)
It turns out that while bit 7 is masked "reserved" it is
not unused, so masking it off as zero is dangerous, and
breaks flash access on some systems such as the NSLU2.
Be more careful and avoid masking off any of the reserved
bits 7, 8, 9 or 30. Only keep masking EXP_WORD (bit 2)
on IXP43x which is necessary in some setups.
Fixes: 1c953bda90 ("bus: ixp4xx: Add a driver for IXP4xx expansion bus")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221122134411.2030372-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ad09d956f upstream.
In iio_register_sw_trigger_type(), configfs_register_default_group() is
possible to fail, but the entry add to iio_trigger_types_list is not
deleted.
This leaves wild in iio_trigger_types_list, which can cause page fault
when module is loading again. So fix this by list_del(&t->list) in error
path.
BUG: unable to handle page fault for address: fffffbfff81d7400
Call Trace:
<TASK>
iio_register_sw_trigger_type
do_one_initcall
do_init_module
load_module
...
Fixes: b662f809d4 ("iio: core: Introduce IIO software triggers")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221108032802.168623-1-chenzhongjin@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6b1a1cf1c upstream.
If the starting position of our insert range happens to be in the hole
between the two ext4_extent_idx, because the lblk of the ext4_extent in
the previous ext4_extent_idx is always less than the start, which leads
to the "extent" variable access across the boundary, the following UAF is
triggered:
==================================================================
BUG: KASAN: use-after-free in ext4_ext_shift_extents+0x257/0x790
Read of size 4 at addr ffff88819807a008 by task fallocate/8010
CPU: 3 PID: 8010 Comm: fallocate Tainted: G E 5.10.0+ #492
Call Trace:
dump_stack+0x7d/0xa3
print_address_description.constprop.0+0x1e/0x220
kasan_report.cold+0x67/0x7f
ext4_ext_shift_extents+0x257/0x790
ext4_insert_range+0x5b6/0x700
ext4_fallocate+0x39e/0x3d0
vfs_fallocate+0x26f/0x470
ksys_fallocate+0x3a/0x70
__x64_sys_fallocate+0x4f/0x60
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
==================================================================
For right shifts, we can divide them into the following situations：
1. When the first ee_block of ext4_extent_idx is greater than or equal to
start, make right shifts directly from the first ee_block.
1) If it is greater than start, we need to continue searching in the
previous ext4_extent_idx.
2) If it is equal to start, we can exit the loop (iterator=NULL).
2. When the first ee_block of ext4_extent_idx is less than start, then
traverse from the last extent to find the first extent whose ee_block
is less than start.
1) If extent is still the last extent after traversal, it means that
the last ee_block of ext4_extent_idx is less than start, that is,
start is located in the hole between idx and (idx+1), so we can
exit the loop directly (break) without right shifts.
2) Otherwise, make right shifts at the corresponding position of the
found extent, and then exit the loop (iterator=NULL).
Fixes: 331573febb ("ext4: Add support FALLOC_FL_INSERT_RANGE for fallocate")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/20220922120434.1294789-1-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel has an awfully complicated boot sequence in order to cope
with the various EL2 configurations, including those that "enhanced"
the architecture. We go from EL2 to EL1, then back to EL2, staying
at EL2 if VHE capable and otherwise go back to EL1.
Here's a paracetamol tablet for you.
The cpu_resume path follows the same logic, because coming up with
two versions of a square wheel is hard.
However, things aren't this straightforward with pKVM, as the host
resume path is always proxied by the hypervisor, which means that
the kernel is always entered at EL1. Which contradicts what the
__boot_cpu_mode[] array contains (it obviously says EL2).
This thus triggers a HVC call from EL1 to EL2 in a vain attempt
to upgrade from EL1 to EL2 VHE, which we are, funnily enough,
reluctant to grant to the host kernel. This is also completely
unexpected, and puzzles your average EL2 hacker.
Address it by fixing up the boot mode at the point the host gets
deprivileged. is_hyp_mode_available() and co already have a static
branch to deal with this, making it pretty safe.
This stable fix doesn't have an upstream version. The entire bootflow
has been reworked from 6.0 and that fixed the boot mode at the same
time, from commit 005e12676a ("arm64: head: record CPU boot mode after
enabling the MMU") to be precise. However, the latter is part of a 20
patches long series and can't be simply cherry-pick'ed.
Link: https://lore.kernel.org/r/20220624150651.1358849-1-ardb@kernel.org/
Link: https://lore.kernel.org/r/20221011165400.1241729-1-maz@kernel.org/
Cc: <stable@vger.kernel.org> # 5.15+
Reported-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Vincent Donnefort <vdonnefort@google.com>
[Vincent: Add a paragraph about why this patch is for stable only]
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 56baa208f9 ]
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
I only patch the bcm7216 variant even though others potentially *could*
provide the 'supports-cqe' property (and thus enable CQHCI), because
d46ba2d17f ("mmc: sdhci-brcmstb: Add support for Command Queuing
(CQE)") and some Broadcom folks confirm that only the 7216 variant
actually supports it.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: d46ba2d17f ("mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.3.I6a715feab6d01f760455865e968ecf0d85036018@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bcc55fe64 ]
Enabling this feature will allow the controller to stop the bus
clock when the bus is idle. The feature is not part of the standard
and is unique to newer Arasan cores and is enabled with a bit in a
vendor specific register. This feature will only be enabled for
non-removable devices because they don't switch the voltage and
clock gating breaks SD Card volatge switching.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220427180853.35970-3-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stable-dep-of: 56baa208f9 ("mmc: sdhci-brcmstb: Fix SDHCI_RESET_ALL for CQHCI")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 869e4ae4cd ]
Add FORCE to placate a warning from make:
arch/nios2/boot/Makefile:24: FORCE prerequisite is missing
Fixes: 2fc8483fdc ("nios2: Build infrastructure")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 534bd70374 ]
When using dash as /bin/sh, the CC_HAS_ASM_GOTO_TIED_OUTPUT test fails
with a syntax error which is not the one we are looking for:
<stdin>: In function ‘foo’:
<stdin>:1:29: warning: missing terminating " character
<stdin>:1:29: error: missing terminating " character
<stdin>:2:5: error: expected ‘:’ before ‘+’ token
<stdin>:2:7: warning: missing terminating " character
<stdin>:2:7: error: missing terminating " character
<stdin>:2:5: error: expected declaration or statement at end of input
Removing '\n' solves this.
Fixes: 1aa0e8b144 ("Kconfig: Add option for asm goto w/ tied outputs to workaround clang-13 bug")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f44e07a8af ]
The size of the TOD programmable field was incorrectly increased from
four to eight bytes with commit 1a2c5840ac ("s390/dump: cleanup CPU
save area handling").
This leads to an elf notes section NT_S390_TODPREG which has a size of
eight instead of four bytes in case of kdump, however even worse is
that the contents is incorrect: it is supposed to contain only the
contents of the TOD programmable field, but in fact contains a mix of
the TOD programmable field (32 bit upper bits) and parts of the CPU
timer register (lower 32 bits).
Fix this by simply changing the size of the todpreg field within the
save area structure. This will implicitly also fix the size of the
corresponding elf notes sections.
This also gets rid of this compile time warning:
in function ‘fortify_memcpy_chk’,
inlined from ‘save_area_add_regs’ at arch/s390/kernel/crash_dump.c:99:2:
./include/linux/fortify-string.h:413:25: error: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field
(2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
413 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 1a2c5840ac ("s390/dump: cleanup CPU save area handling")
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad17c2a3f1 ]
pci_get_device() will decrease the reference count for the *from*
parameter. So we don't need to call put_device() to decrease the
reference. Let's remove the put_device() in the loop and only decrease
the reference count of the returned 'pdev' for the last loop because it
will not be passed to pci_get_device() as input parameter. We don't need
to check if 'pdev' is NULL because it is already checked inside
pci_dev_put(). Also add pci_dev_put() for the error path.
Fixes: fe1939bb23 ("octeontx2-af: Add SDP interface support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Link: https://lore.kernel.org/r/20221123065919.31499-1-wangxiongfeng2@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 290b5fe096 ]
In the blamed commit, a rudimentary reallocation procedure for RX buffer
descriptors was implemented, for the situation when their format changes
between normal (no PTP) and extended (PTP).
enetc_hwtstamp_set() calls enetc_close() and enetc_open() in a sequence,
and this sequence loses information which was previously configured in
the TX BDR Mode Register, specifically via the enetc_set_bdr_prio() call.
The TX ring priority is configured by tc-mqprio and tc-taprio, and
affects important things for TSN such as the TX time of packets. The
issue manifests itself most visibly by the fact that isochron --txtime
reports premature packet transmissions when PTP is first enabled on an
enetc interface.
Save the TX ring priority in a new field in struct enetc_bdr (occupies a
2 byte hole on arm64) in order to make this survive a ring reconfiguration.
Fixes: 434cebabd3 ("enetc: Add dynamic allocation of extended Rx BD rings")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/r/20221122130936.1704151-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 715bf2610f ]
The &priv->si->hw construct dereferences 2 pointers and makes lines
longer than they need to be, in turn making the code harder to read.
Replace &priv->si->hw accesses with a "hw" variable when there are 2 or
more accesses within a function that dereference this. This includes
loops, since &priv->si->hw is a loop invariant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 290b5fe096 ("net: enetc: preserve TX ring priority across reconfiguration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32bf8e1f6f ]
Future work in this driver would like to look at priv->active_offloads &
ENETC_F_QBV to determine whether a tc-taprio qdisc offload was
installed, but this does not produce the intended effect.
All the other flags in priv->active_offloads are managed dynamically,
except ENETC_F_QBV which is set statically based on the probed SI capability.
This change makes priv->active_offloads & ENETC_F_QBV really track the
presence of a tc-taprio schedule on the port.
Some existing users, like the enetc_sched_speed_set() call from
phylink_mac_link_up(), are best kept using the old logic: the tc-taprio
offload does not re-trigger another link mode resolve, so the scheduler
needs to be functional from the get go, as long as Qbv is supported at
all on the port. So to preserve functionality there, look at the static
station interface capability from pf->si->hw_features instead.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 290b5fe096 ("net: enetc: preserve TX ring priority across reconfiguration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0254f31a7d ]
The transaction buffer is allocated by using the size of the packet buf,
and subtracting two which seems intended to remove the two tags which are
not present in the target structure. This calculation leads to under
counting memory because of differences between the packet contents and the
target structure. The aid_len field is a u8 in the packet, but a u32 in
the structure, resulting in at least 3 bytes always being under counted.
Further, the aid data is a variable length field in the packet, but fixed
in the structure, so if this field is less than the max, the difference is
added to the under counting.
To fix, perform validation checks progressively to safely reach the
next field, to determine the size of both buffers and verify both tags.
Once all validation checks pass, allocate the buffer and copy the data.
This eliminates freeing memory on the error path, as validation checks are
moved ahead of memory allocation.
Reported-by: Denis Efremov <denis.e.efremov@oracle.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Fixes: 5d1ceb7f5e ("NFC: st21nfcb: Add HCI transaction event support")
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c60c152230 ]
The first validation check for EVT_TRANSACTION has two different checks
tied together with logical AND. One is a check for minimum packet length,
and the other is for a valid aid_tag. If either condition is true (fails),
then an error should be triggered. The fix is to change && to ||.
Reported-by: Denis Efremov <denis.e.efremov@oracle.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Fixes: 5d1ceb7f5e ("NFC: st21nfcb: Add HCI transaction event support")
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 590ce6d96d ]
For DASD devices in raw_track_access mode only full track images are
read and written.
For this purpose it is not necessary to do search operation in the
locate record extended function. The documentation even states that
this might fail if the searched record is not found on a track.
Currently the driver sets a value of 1 in the search field for the first
record after record zero. This is the default for disks not in
raw_track_access mode but record 1 might be missing on a completely
empty track.
There has not been any problem with this on IBM storage servers but it
might lead to errors with DASD devices on other vendors storage servers.
Fix this by setting the search field to 0. Record zero is always available
even on a completely empty track.
Fixes: e4dbb0f2b5 ("[S390] dasd: Add support for raw ECKD access.")
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20221123160719.3002694-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c40cde6b5 ]
In com20020_probe(), if com20020_config() fails, dev and info
will not be freed, which will lead to a memory leak.
This patch adds freeing dev and info after com20020_config()
fails to fix this bug.
Compile tested only.
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
