[ Upstream commit 3e01d52546 ]
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: stable@vger.kernel.org
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ravi Chandra Minnikanti <rminnikanti@marvell.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-1-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc9b364bb1 ]
There are race conditions that may lead to inet6_dev refcount underflow
in xfrm6_dst_destroy() and rt6_uncached_list_flush_dev().
One of the refcount underflow bugs is shown below:
(cpu 1) | (cpu 2)
xfrm6_dst_destroy() |
... |
in6_dev_put() |
| rt6_uncached_list_flush_dev()
... | ...
| in6_dev_put()
rt6_uncached_list_del() | ...
... |
xfrm6_dst_destroy() calls rt6_uncached_list_del() after in6_dev_put(),
so rt6_uncached_list_flush_dev() has a chance to call in6_dev_put()
again for the same inet6_dev.
Fix it by moving in6_dev_put() after rt6_uncached_list_del() in
xfrm6_dst_destroy().
Fixes: 510c321b55 ("xfrm: reuse uncached_list to track xdsts")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b384cc74b ]
Looks like the driver sleep pins configuration is unusable. Adding the
sleep pins causes the usb phy to not respond. We need to use the default
pins in probe, and only set sleep pins at phy_mdm6600_device_power_off().
As the modem can also be booted to a serial port mode for firmware
flashing, let's make the pin changes limited to probe and remove. For
probe, we get the default pins automatically. We only need to set the
sleep pins in phy_mdm6600_device_power_off() to prevent the modem from
waking up because the gpio line glitches.
If it turns out that we need a separate state for phy_mdm6600_power_on()
and phy_mdm6600_power_off(), we can use the pinctrl idle state.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Fixes: 2ad2af0816 ("phy: mapphone-mdm6600: Improve phy related runtime PM calls")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230913060433.48373-3-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fc363413ef upstream.
We found a glitch when configuring the pad as output high. To avoid this
glitch, move the data value setting before direction config in the
function vf610_gpio_direction_output().
Fixes: 659d8a6231 ("gpio: vf610: add imx7ulp support")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
[Bartosz: tweak the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1ae1c59c8 upstream.
Since the fixed commits both zdev->iommu_bitmap and zdev->lazy_bitmap
are allocated as vzalloc(zdev->iommu_pages / 8). The problem is that
zdev->iommu_bitmap is a pointer to unsigned long but the above only
yields an allocation that is a multiple of sizeof(unsigned long) which
is 8 on s390x if the number of IOMMU pages is a multiple of 64.
This in turn is the case only if the effective IOMMU aperture is
a multiple of 64 * 4K = 256K. This is usually the case and so didn't
cause visible issues since both the virt_to_phys(high_memory) reduced
limit and hardware limits use nice numbers.
Under KVM, and in particular with QEMU limiting the IOMMU aperture to
the vfio DMA limit (default 65535), it is possible for the reported
aperture not to be a multiple of 256K however. In this case we end up
with an iommu_bitmap whose allocation is not a multiple of
8 causing bitmap operations to access it out of bounds.
Sadly we can't just fix this in the obvious way and use bitmap_zalloc()
because for large RAM systems (tested on 8 TiB) the zdev->iommu_bitmap
grows too large for kmalloc(). So add our own bitmap_vzalloc() wrapper.
This might be a candidate for common code, but this area of code will
be replaced by the upcoming conversion to use the common code DMA API on
s390 so just add a local routine.
Fixes: 2245932155 ("s390/pci: use virtual memory for iommu bitmap")
Fixes: 13954fd691 ("s390/pci_dma: improve lazy flush for unmap")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32671e3799 upstream.
Because group consistency is non-atomic between parent (filedesc) and children
(inherited) events, it is possible for PERF_FORMAT_GROUP read() to try and sum
non-matching counter groups -- with non-sensical results.
Add group_generation to distinguish the case where a parent group removes and
adds an event and thus has the same number, but a different configuration of
events as inherited groups.
This became a problem when commit fa8c269353 ("perf/core: Invert
perf_read_group() loops") flipped the order of child_list and sibling_list.
Previously it would iterate the group (sibling_list) first, and for each
sibling traverse the child_list. In this order, only the group composition of
the parent is relevant. By flipping the order the group composition of the
child (inherited) events becomes an issue and the mis-match in group
composition becomes evident.
That said; even prior to this commit, while reading of a group that is not
equally inherited was not broken, it still made no sense.
(Ab)use ECHILD as error return to indicate issues with child process group
composition.
Fixes: fa8c269353 ("perf/core: Invert perf_read_group() loops")
Reported-by: Budimir Markovic <markovicbudimir@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231018115654.GK33217@noisy.programming.kicks-ass.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c21a18d5d upstream.
acpi_register_gsi() should return a negative value in case of failure.
Currently, it returns the return value from irq_create_fwspec_mapping().
However, irq_create_fwspec_mapping() returns 0 for failure. Fix the
issue by returning -EINVAL if irq_create_fwspec_mapping() returns zero.
Fixes: d44fa3d460 ("ACPI: Add support for ResourceSource/IRQ domain mapping")
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
[ rjw: Rename a new local variable ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84ee19bffc upstream.
The OEMID is an 8-bit binary number rather than 16-bit as the current code
parses for. The OEMID occupies bits [111:104] in the CID register, see the
eMMC spec JESD84-B51 paragraph 7.2.3. It seems that the 16-bit comes from
the legacy MMC specs (v3.31 and before).
Let's fix the parsing by simply move to use 8-bit instead of 16-bit. This
means we ignore the impact on some of those old MMC cards that may be out
there, but on the other hand this shouldn't be a problem as the OEMID seems
not be an important feature for these cards.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230927071500.1791882-1-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b541260615 ]
memcmp is not consider safe to use with cryptographic secrets:
'Do not use memcmp() to compare security critical data, such as
cryptographic secrets, because the required CPU time depends on the
number of equal bytes.'
While usage of memcmp for ZERO_KEY may not be considered a security
critical data, it can lead to more usage of memcmp with pairing keys
which could introduce more security problems.
Fixes: 455c2ff0a5 ("Bluetooth: Fix BR/EDR out-of-band pairing with only initiator data")
Fixes: 33155c4aae ("Bluetooth: hci_event: Ignore NULL link key")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9147b9ded4 ]
Jens reported the following warnings from -Wmaybe-uninitialized recent
Linus' branch.
In file included from ./include/asm-generic/rwonce.h:26,
from ./arch/arm64/include/asm/rwonce.h:71,
from ./include/linux/compiler.h:246,
from ./include/linux/export.h:5,
from ./include/linux/linkage.h:7,
from ./include/linux/kernel.h:17,
from fs/btrfs/ioctl.c:6:
In function ‘instrument_copy_from_user_before’,
inlined from ‘_copy_from_user’ at ./include/linux/uaccess.h:148:3,
inlined from ‘copy_from_user’ at ./include/linux/uaccess.h:183:7,
inlined from ‘btrfs_ioctl_space_info’ at fs/btrfs/ioctl.c:2999:6,
inlined from ‘btrfs_ioctl’ at fs/btrfs/ioctl.c:4616:10:
./include/linux/kasan-checks.h:38:27: warning: ‘space_args’ may be used
uninitialized [-Wmaybe-uninitialized]
38 | #define kasan_check_write __kasan_check_write
./include/linux/instrumented.h:129:9: note: in expansion of macro
‘kasan_check_write’
129 | kasan_check_write(to, n);
| ^~~~~~~~~~~~~~~~~
./include/linux/kasan-checks.h: In function ‘btrfs_ioctl’:
./include/linux/kasan-checks.h:20:6: note: by argument 1 of type ‘const
volatile void *’ to ‘__kasan_check_write’ declared here
20 | bool __kasan_check_write(const volatile void *p, unsigned int
size);
| ^~~~~~~~~~~~~~~~~~~
fs/btrfs/ioctl.c:2981:39: note: ‘space_args’ declared here
2981 | struct btrfs_ioctl_space_args space_args;
| ^~~~~~~~~~
In function ‘instrument_copy_from_user_before’,
inlined from ‘_copy_from_user’ at ./include/linux/uaccess.h:148:3,
inlined from ‘copy_from_user’ at ./include/linux/uaccess.h:183:7,
inlined from ‘_btrfs_ioctl_send’ at fs/btrfs/ioctl.c:4343:9,
inlined from ‘btrfs_ioctl’ at fs/btrfs/ioctl.c:4658:10:
./include/linux/kasan-checks.h:38:27: warning: ‘args32’ may be used
uninitialized [-Wmaybe-uninitialized]
38 | #define kasan_check_write __kasan_check_write
./include/linux/instrumented.h:129:9: note: in expansion of macro
‘kasan_check_write’
129 | kasan_check_write(to, n);
| ^~~~~~~~~~~~~~~~~
./include/linux/kasan-checks.h: In function ‘btrfs_ioctl’:
./include/linux/kasan-checks.h:20:6: note: by argument 1 of type ‘const
volatile void *’ to ‘__kasan_check_write’ declared here
20 | bool __kasan_check_write(const volatile void *p, unsigned int
size);
| ^~~~~~~~~~~~~~~~~~~
fs/btrfs/ioctl.c:4341:49: note: ‘args32’ declared here
4341 | struct btrfs_ioctl_send_args_32 args32;
| ^~~~~~
This was due to his config options and having KASAN turned on,
which adds some extra checks around copy_from_user(), which then
triggered the -Wmaybe-uninitialized checker for these cases.
Fix the warnings by initializing the different structs we're copying
into.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a70e5cbed ]
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61304336c6 ]
Lower layer device driver stop/wake TX by calling ieee80211_stop_queue()/
ieee80211_wake_queue() while hw scan. Sometimes hw scan and PTK rekey are
running in parallel, when M4 sent from wpa_supplicant arrive while the TX
queue is stopped, then the M4 will pending send, and then new key install
from wpa_supplicant. After TX queue wake up by lower layer device driver,
the M4 will be dropped by below call stack.
When key install started, the current key flag is set KEY_FLAG_TAINTED in
ieee80211_pairwise_rekey(), and then mac80211 wait key install complete by
lower layer device driver. Meanwhile ieee80211_tx_h_select_key() will return
TX_DROP for the M4 in step 12 below, and then ieee80211_free_txskb() called
by ieee80211_tx_dequeue(), so the M4 will not send and free, then the rekey
process failed becaue AP not receive M4. Please see details in steps below.
There are a interval between KEY_FLAG_TAINTED set for current key flag and
install key complete by lower layer device driver, the KEY_FLAG_TAINTED is
set in this interval, all packet including M4 will be dropped in this
interval, the interval is step 8~13 as below.
issue steps:
TX thread install key thread
1. stop_queue -idle-
2. sending M4 -idle-
3. M4 pending -idle-
4. -idle- starting install key from wpa_supplicant
5. -idle- =>ieee80211_key_replace()
6. -idle- =>ieee80211_pairwise_rekey() and set
currently key->flags |= KEY_FLAG_TAINTED
7. -idle- =>ieee80211_key_enable_hw_accel()
8. -idle- =>drv_set_key() and waiting key install
complete from lower layer device driver
9. wake_queue -waiting state-
10. re-sending M4 -waiting state-
11. =>ieee80211_tx_h_select_key() -waiting state-
12. drop M4 by KEY_FLAG_TAINTED -waiting state-
13. -idle- install key complete with success/fail
success: clear flag KEY_FLAG_TAINTED
fail: start disconnect
Hence add check in step 11 above to allow the EAPOL send out in the
interval. If lower layer device driver use the old key/cipher to encrypt
the M4, then AP received/decrypt M4 correctly, after M4 send out, lower
layer device driver install the new key/cipher to hardware and return
success.
If lower layer device driver use new key/cipher to send the M4, then AP
will/should drop the M4, then it is same result with this issue, AP will/
should kick out station as well as this issue.
issue log:
kworker/u16:4-5238 [000] 6456.108926: stop_queue: phy1 queue:0, reason:0
wpa_supplicant-961 [003] 6456.119737: rdev_tx_control_port: wiphy_name=phy1 name=wlan0 ifindex=6 dest=ARRAY[9e, 05, 31, 20, 9b, d0] proto=36488 unencrypted=0
wpa_supplicant-961 [003] 6456.119839: rdev_return_int_cookie: phy1, returned 0, cookie: 504
wpa_supplicant-961 [003] 6456.120287: rdev_add_key: phy1, netdev:wlan0(6), key_index: 0, mode: 0, pairwise: true, mac addr: 9e:05:31:20:9b:d0
wpa_supplicant-961 [003] 6456.120453: drv_set_key: phy1 vif:wlan0(2) sta:9e:05:31:20:9b:d0 cipher:0xfac04, flags=0x9, keyidx=0, hw_key_idx=0
kworker/u16:9-3829 [001] 6456.168240: wake_queue: phy1 queue:0, reason:0
kworker/u16:9-3829 [001] 6456.168255: drv_wake_tx_queue: phy1 vif:wlan0(2) sta:9e:05:31:20:9b:d0 ac:0 tid:7
kworker/u16:9-3829 [001] 6456.168305: cfg80211_control_port_tx_status: wdev(1), cookie: 504, ack: false
wpa_supplicant-961 [003] 6459.167982: drv_return_int: phy1 - -110
issue call stack:
nl80211_frame_tx_status+0x230/0x340 [cfg80211]
cfg80211_control_port_tx_status+0x1c/0x28 [cfg80211]
ieee80211_report_used_skb+0x374/0x3e8 [mac80211]
ieee80211_free_txskb+0x24/0x40 [mac80211]
ieee80211_tx_dequeue+0x644/0x954 [mac80211]
ath10k_mac_tx_push_txq+0xac/0x238 [ath10k_core]
ath10k_mac_op_wake_tx_queue+0xac/0xe0 [ath10k_core]
drv_wake_tx_queue+0x80/0x168 [mac80211]
__ieee80211_wake_txqs+0xe8/0x1c8 [mac80211]
_ieee80211_wake_txqs+0xb4/0x120 [mac80211]
ieee80211_wake_txqs+0x48/0x80 [mac80211]
tasklet_action_common+0xa8/0x254
tasklet_action+0x2c/0x38
__do_softirq+0xdc/0x384
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230801064751.25803-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcda165706 ]
This fixes the following warnings:
net/bluetooth/hci_core.c: In function ‘hci_register_dev’:
net/bluetooth/hci_core.c:2620:54: warning: ‘%d’ directive output may
be truncated writing between 1 and 10 bytes into a region of size 5
[-Wformat-truncation=]
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~
net/bluetooth/hci_core.c:2620:50: note: directive argument in the range
[0, 2147483647]
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~~~~~~
net/bluetooth/hci_core.c:2620:9: note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 8
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d8e801422 ]
While executing the Android 13 CTS Verifier Secure Server test on a
ChromeOS device, it was observed that the Bluetooth host initiates
authentication for an RFCOMM connection after SSP completes.
When this happens, some Intel Bluetooth controllers, like AC9560, would
disconnect with "Connection Rejected due to Security Reasons (0x0e)".
Historically, BlueZ did not mandate this authentication while an
authenticated combination key was already in use for the connection.
This behavior was changed since commit 7b5a9241b7
("Bluetooth: Introduce requirements for security level 4").
So, this patch addresses the aforementioned disconnection issue by
restoring the previous behavior.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffe3b7837a ]
There is a slab-out-of-bounds Write bug in hid-holtek-kbd driver.
The problem is the driver assumes the device must have an input
but some malicious devices violate this assumption.
Fix this by checking hid_device's input is non-empty before its usage.
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23cce5f254 ]
When kernel is compiled without preemption, the eval_map_work_func()
(which calls trace_event_eval_update()) will not be preempted up to its
complete execution. This can actually cause a problem since if another
CPU call stop_machine(), the call will have to wait for the
eval_map_work_func() function to finish executing in the workqueue
before being able to be scheduled. This problem was observe on a SMP
system at boot time, when the CPU calling the initcalls executed
clocksource_done_booting() which in the end calls stop_machine(). We
observed a 1 second delay because one CPU was executing
eval_map_work_func() and was not preempted by the stop_machine() task.
Adding a call to cond_resched() in trace_event_eval_update() allows
other tasks to be executed and thus continue working asynchronously
like before without blocking any pending task at boot time.
Link: https://lore.kernel.org/linux-trace-kernel/20230929191637.416931-1-cleger@rivosinc.com
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49728bdc70 ]
The 6 bytes length of the tries_buf string in ata_eh_link_report() is
too short and results in a gcc compilation warning with W-!:
drivers/ata/libata-eh.c: In function ‘ata_eh_link_report’:
drivers/ata/libata-eh.c:2371:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 4 [-Wformat-truncation=]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~
drivers/ata/libata-eh.c:2371:56: note: directive argument in the range [-2147483648, 4]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~
drivers/ata/libata-eh.c:2371:17: note: ‘snprintf’ output between 4 and 14 bytes into a destination of size 6
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2372 | ap->eh_tries);
| ~~~~~~~~~~~~~
Avoid this warning by increasing the string size to 16B.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e8bc2dda5 ]
As timbgpio_irq_enable()/timbgpio_irq_disable() callback could be
executed under irq context, it could introduce double locks on
&tgpio->lock if it preempts other execution units requiring
the same locks.
timbgpio_gpio_set()
--> timbgpio_update_bit()
--> spin_lock(&tgpio->lock)
<interrupt>
--> timbgpio_irq_disable()
--> spin_lock_irqsave(&tgpio->lock)
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_irqsave()
on &tgpio->lock inside timbgpio_gpio_set() to prevent the possible
deadlock scenario.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03dbab3bba ]
Nathan reported that he was seeing the new warning in
setattr_copy_mgtime pop when starting podman containers. Overlayfs is
trying to set the atime and mtime via notify_change without also
setting the ctime.
POSIX states that when the atime and mtime are updated via utimes() that
we must also update the ctime to the current time. The situation with
overlayfs copy-up is analogies, so add ATTR_CTIME to the bitmask.
notify_change will fill in the value.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Amir Goldstein <amir73il@gmail.com>
Message-Id: <20230913-ctime-v1-1-c6bc509cbc27@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13e59e74f ]
I2C_CLASS_DEPRECATED is a flag and not an actual class.
There's nothing speaking against both, parent and child, having
I2C_CLASS_DEPRECATED set. Therefore exclude it from the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4c639f699 ]
Jens reported a compiler warning when using
CONFIG_CC_OPTIMIZE_FOR_SIZE=y that looks like this
fs/btrfs/tree-log.c: In function ‘btrfs_log_prealloc_extents’:
fs/btrfs/tree-log.c:4828:23: warning: ‘start_slot’ may be used
uninitialized [-Wmaybe-uninitialized]
4828 | ret = copy_items(trans, inode, dst_path, path,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
4829 | start_slot, ins_nr, 1, 0);
| ~~~~~~~~~~~~~~~~~~~~~~~~~
fs/btrfs/tree-log.c:4725:13: note: ‘start_slot’ was declared here
4725 | int start_slot;
| ^~~~~~~~~~
The compiler is incorrect, as we only use this code when ins_len > 0,
and when ins_len > 0 we have start_slot properly initialized. However
we generally find the -Wmaybe-uninitialized warnings valuable, so
initialize start_slot to get rid of the warning.
Reported-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bf76df3fe ]
When running a delayed tree reference, if we find a ref count different
from 1, we return -EIO. This isn't an IO error, as it indicates either a
bug in the delayed refs code or a memory corruption, so change the error
code from -EIO to -EUCLEAN. Also tag the branch as 'unlikely' as this is
not expected to ever happen, and change the error message to print the
tree block's bytenr without the parenthesis (and there was a missing space
between the 'block' word and the opening parenthesis), for consistency as
that's the style we used everywhere else.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad37b5e30 ]
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1ed72171e ]
Like various other ASUS ExpertBook-s, the ASUS ExpertBook B1402CBA
has an ACPI DSDT table that describes IRQ 1 as ActiveLow while
the kernel overrides it to EdgeHigh.
This prevents the keyboard from working. To fix this issue, add this laptop
to the skip_override_table so that the kernel does not override IRQ 1.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217901
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05cda42712 ]
Like the ASUS ExpertBook B2502CBA and various ASUS Vivobook laptops, the
ASUS ExpertBook B1502CBA has an ACPI DSDT table that describes IRQ 1 as
ActiveLow while the kernel overrides it to Edge_High.
$ sudo dmesg | grep DMI
DMI: ASUSTeK COMPUTER INC. ASUS EXPERTBOOK B1502CBA_B1502CBA/B1502CBA, BIOS B1502CBA.300 01/18/2023
$ grep -A 40 PS2K dsdt.dsl | grep IRQ -A 1
IRQ (Level, ActiveLow, Exclusive, )
{1}
This prevents the keyboard from working. To fix this issue, add this laptop
to the skip_override_table so that the kernel does not override IRQ 1.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217323
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: c1ed72171e ("ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77c7248882 ]
Like the Asus Expertbook B2502CBA and various Asus Vivobook laptops,
the Asus Expertbook B2402CBA has an ACPI DSDT table that describes IRQ 1
as ActiveLow while the kernel overrides it to Edge_High. This prevents the
keyboard from working. To fix this issue, add this laptop to the
skip_override_table so that the kernel does not override IRQ 1.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216864
Tested-by: zelenat <zelenat@gmail.com>
Signed-off-by: Tamim Khan <tamim@fusetak.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: c1ed72171e ("ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7203481fd1 ]
The Asus ExpertBook B2502 has the same keyboard issue as Asus Vivobook
K3402ZA/K3502ZA. The kernel overrides IRQ 1 to Edge_High when it
should be Active_Low.
This patch adds the ExpertBook B2502 model to the existing
quirk list of Asus laptops with this issue.
Fixes: b5f9223a10 ("ACPI: resource: Skip IRQ override on Asus Vivobook S5602ZA")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2142574
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: c1ed72171e ("ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5f9223a10 ]
Like the Asus Vivobook K3402ZA/K3502ZA/S5402ZA Asus Vivobook S5602ZA
has an ACPI DSDT table the describes IRQ 1 as ActiveLow while the kernel
overrides it to Edge_High. This prevents the keyboard on this laptop
from working. To fix this add this laptop to the skip_override_table so
that the kernel does not override IRQ 1.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216579
Tested-by: Dzmitry <wrkedm@gmail.com>
Signed-off-by: Tamim Khan <tamim@fusetak.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: c1ed72171e ("ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e12dee3736 ]
In the ACPI DSDT table for Asus VivoBook K3402ZA/K3502ZA
IRQ 1 is described as ActiveLow; however, the kernel overrides
it to Edge_High. This prevents the internal keyboard from working
on these laptops. In order to fix this add these laptops to the
skip_override_table so that the kernel does not override IRQ 1 to
Edge_High.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216158
Reviewed-by: Hui Wang <hui.wang@canonical.com>
Tested-by: Tamim Khan <tamim@fusetak.com>
Tested-by: Sunand <sunandchakradhar@gmail.com>
Signed-off-by: Tamim Khan <tamim@fusetak.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: c1ed72171e ("ACPI: resource: Skip IRQ override on ASUS ExpertBook B1402CBA")
Signed-off-by: Sasha Levin <sashal@kernel.org>
