[ Upstream commit 9122a70a63 ]
During a testing of an user-space application which transmits UDP
multicast datagrams and utilizes multicast routing to send the UDP
datagrams out of defined network interfaces, I've found a multicast
router does not fill-in UDP checksum into locally produced, looped-back
and forwarded UDP datagrams, if an original output NIC the datagrams
are sent to has UDP TX checksum offload enabled.
The datagrams are sent malformed out of the NIC the datagrams have been
forwarded to.
It is because:
1. If TX checksum offload is enabled on the output NIC, UDP checksum
is not calculated by kernel and is not filled into skb data.
2. dev_loopback_xmit(), which is called solely by
ip_mc_finish_output(), sets skb->ip_summed = CHECKSUM_UNNECESSARY
unconditionally.
3. Since 35fc92a9 ("[NET]: Allow forwarding of ip_summed except
CHECKSUM_COMPLETE"), the ip_summed value is preserved during
forwarding.
4. If ip_summed != CHECKSUM_PARTIAL, checksum is not calculated during
a packet egress.
The minimum fix in dev_loopback_xmit():
1. Preserves skb->ip_summed CHECKSUM_PARTIAL. This is the
case when the original output NIC has TX checksum offload enabled.
The effects are:
a) If the forwarding destination interface supports TX checksum
offloading, the NIC driver is responsible to fill-in the
checksum.
b) If the forwarding destination interface does NOT support TX
checksum offloading, checksums are filled-in by kernel before
skb is submitted to the NIC driver.
c) For local delivery, checksum validation is skipped as in the
case of CHECKSUM_UNNECESSARY, thanks to skb_csum_unnecessary().
2. Translates ip_summed CHECKSUM_NONE to CHECKSUM_UNNECESSARY. It
means, for CHECKSUM_NONE, the behavior is unmodified and is there
to skip a looped-back packet local delivery checksum validation.
Signed-off-by: Cyril Strejc <cyril.strejc@skoda.cz>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 926245c7d2 ]
page_frag_free() won't completely release the memory
allocated for the commands, the cache page must be explicitly
freed by calling __page_frag_cache_drain().
This bug can be easily reproduced by repeatedly
executing the following command on the initiator:
$echo 1 > /sys/devices/virtual/nvme-fabrics/ctl/nvme0/reset_controller
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 042b2046d0 ]
The tx queues are not stopped during the live migration. As a result, the
ndo_start_xmit() may access netfront_info->queues which is freed by
talk_to_netback()->xennet_destroy_queues().
This patch is to netif_device_detach() at the beginning of xen-netfront
resuming, and netif_device_attach() at the end of resuming.
CPU A CPU B
talk_to_netback()
-> if (info->queues)
xennet_destroy_queues(info);
to free netfront_info->queues
xennet_start_xmit()
to access netfront_info->queues
-> err = xennet_create_queues(info, &num_queues);
The idea is borrowed from virtio-net.
Cc: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 162079f2dc ]
The Winbond MMC driver fails to build on ARCH=m68k so prevent
that build config. Silences these build errors:
../drivers/mmc/host/wbsd.c: In function 'wbsd_request_end':
../drivers/mmc/host/wbsd.c:212:28: error: implicit declaration of function 'claim_dma_lock' [-Werror=implicit-function-declaration]
212 | dmaflags = claim_dma_lock();
../drivers/mmc/host/wbsd.c:215:17: error: implicit declaration of function 'release_dma_lock'; did you mean 'release_task'? [-Werror=implicit-function-declaration]
215 | release_dma_lock(dmaflags);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211017175949.23838-1-rdunlap@infradead.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55dd7e0590 ]
Commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx delay
config") sets the RX/TX delay according to the phy-mode property in the
device tree. For the A20-olinuxino-lime2 board this is "rgmii", which is the
wrong setting.
Following the example of a900cac375 ("ARM: dts: sun7i: a20: bananapro:
Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets
the Ethernet working again on this board.
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210916081721.237137-1-rouca@debian.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8017c99680 ]
On arm64 randconfig builds, hyperv sometimes fails with this
error:
In file included from drivers/hv/hv_trace.c:3:
In file included from drivers/hv/hyperv_vmbus.h:16:
In file included from arch/arm64/include/asm/sync_bitops.h:5:
arch/arm64/include/asm/bitops.h:11:2: error: only <linux/bitops.h> can be included directly
In file included from include/asm-generic/bitops/hweight.h:5:
include/asm-generic/bitops/arch_hweight.h:9:9: error: implicit declaration of function '__sw_hweight32' [-Werror,-Wimplicit-function-declaration]
include/asm-generic/bitops/atomic.h:17:7: error: implicit declaration of function 'BIT_WORD' [-Werror,-Wimplicit-function-declaration]
Include the correct header first.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211018131929.2260087-1-arnd@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf6abf345d ]
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c62041c5ba ]
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c85 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69b2f4687 ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e211210098 ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a8f71014b ]
The sgl is freed in the target stack in target_release_cmd_kref() before
calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that
causes a panic if sgl is not yet DMA unmapped:
NIP dma_direct_unmap_sg+0xdc/0x180
LR dma_direct_unmap_sg+0xc8/0x180
Call Trace:
ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable)
dma_unmap_sg_attrs+0x54/0xf0
qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx]
qlt_free_cmd+0x124/0x1d0 [qla2xxx]
tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx]
target_put_sess_cmd+0x198/0x370 [target_core_mod]
transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod]
tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx]
The sgl may be left unmapped in error cases of response sending. For
instance, qlt_rdy_to_xfer() maps sgl and exits when session is being
deleted keeping the sgl mapped.
This patch removes use-after-free of the sgl and ensures that the sgl is
unmapped for any command that was not sent to firmware.
Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cddb44bd ]
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d94befbb5a ]
In laptop 'HP Spectre x360 Convertible 15-eb1xxx/8811' both front and
rear speakers are silent, this patch fixes that by overriding the pin
layout and by initializing the amplifier which needs a GPIO pin to be
set to 1 then 0, similar to the existing HP Spectre x360 14 model.
In order to have volume control, both front and rear speakers were
forced to use the DAC1.
This patch also correctly map the mute LED but since there is no
microphone on/off switch exposed by the alsa subsystem it never turns
on by itself.
There are still known audio issues in this laptop: headset microphone
doesn't work, the button to mute/unmute microphone is not yet mapped,
the LED of the mute/unmute speakers doesn't seems to be exposed via
GPIO and never turns on.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213953
Signed-off-by: Davide Baldo <davide@baldo.me>
Link: https://lore.kernel.org/r/20211015072121.5287-1-davide@baldo.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c448b7aa3e ]
'component' is allocated in snd_soc_register_component(), but component->list
is not initalized, this may cause snd_soc_del_component_unlocked() deref null
ptr in the error handing case.
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:__list_del_entry_valid+0x81/0xf0
Call Trace:
snd_soc_del_component_unlocked+0x69/0x1b0 [snd_soc_core]
snd_soc_add_component.cold+0x54/0x6c [snd_soc_core]
snd_soc_register_component+0x70/0x90 [snd_soc_core]
devm_snd_soc_register_component+0x5e/0xd0 [snd_soc_core]
tas2552_probe+0x265/0x320 [snd_soc_tas2552]
? tas2552_component_probe+0x1e0/0x1e0 [snd_soc_tas2552]
i2c_device_probe+0xa31/0xbe0
Fix by adding INIT_LIST_HEAD() to snd_soc_component_initialize().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211009065840.3196239-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ff53f6a43 upstream.
Add a synchronize_rcu() after clearing the posted interrupt wakeup handler
to ensure all readers, i.e. in-flight IRQ handlers, see the new handler
before returning to the caller. If the caller is an exiting module and
is unregistering its handler, failure to wait could result in the IRQ
handler jumping into an unloaded module.
The registration path doesn't require synchronization, as it's the
caller's responsibility to not generate interrupts it cares about until
after its handler is registered.
Fixes: f6b3c72c23 ("x86/irq: Define a global vector for VT-d Posted-Interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211009001107.3936588-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415de44076 upstream.
Currently, Linux probes for X86_BUG_NULL_SEL unconditionally which
makes it unsafe to migrate in a virtualised environment as the
properties across the migration pool might differ.
To be specific, the case which goes wrong is:
1. Zen1 (or earlier) and Zen2 (or later) in a migration pool
2. Linux boots on Zen2, probes and finds the absence of X86_BUG_NULL_SEL
3. Linux is then migrated to Zen1
Linux is now running on a X86_BUG_NULL_SEL-impacted CPU while believing
that the bug is fixed.
The only way to address the problem is to fully trust the "no longer
affected" CPUID bit when virtualised, because in the above case it would
be clear deliberately to indicate the fact "you might migrate to
somewhere which has this behaviour".
Zen3 adds the NullSelectorClearsBase CPUID bit to indicate that loading
a NULL segment selector zeroes the base and limit fields, as well as
just attributes. Zen2 also has this behaviour but doesn't have the NSCB
bit.
[ bp: Minor touchups. ]
Signed-off-by: Jane Malalane <jane.malalane@citrix.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20211021104744.24126-1-jane.malalane@citrix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d445ab26 upstream.
When runtime support for converting between 4-level and 5-level pagetables
was added to the kernel, the SME code that built pagetables was updated
to use the pagetable functions, e.g. p4d_offset(), etc., in order to
simplify the code. However, the use of the pagetable functions in early
boot code requires the use of the USE_EARLY_PGTABLE_L5 #define in order to
ensure that the proper definition of pgtable_l5_enabled() is used.
Without the #define, pgtable_l5_enabled() is #defined as
cpu_feature_enabled(X86_FEATURE_LA57). In early boot, the CPU features
have not yet been discovered and populated, so pgtable_l5_enabled() will
return false even when 5-level paging is enabled. This causes the SME code
to always build 4-level pagetables to perform the in-place encryption.
If 5-level paging is enabled, switching to the SME pagetables results in
a page-fault that kills the boot.
Adding the #define results in pgtable_l5_enabled() using the
__pgtable_l5_enabled variable set in early boot and the SME code building
pagetables for the proper paging level.
Fixes: aad983913d ("x86/mm/encrypt: Simplify sme_populate_pgd() and sme_populate_pgd_large()")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.18.x
Link: https://lkml.kernel.org/r/2cb8329655f5c753905812d951e212022a480475.1634318656.git.thomas.lendacky@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 712a951025 upstream.
It is possible to trigger a crash by splicing anon pipe bufs to the fuse
device.
The reason for this is that anon_pipe_buf_release() will reuse buf->page if
the refcount is 1, but that page might have already been stolen and its
flags modified (e.g. PG_lru added).
This happens in the unlikely case of fuse_dev_splice_write() getting around
to calling pipe_buf_release() after a page has been stolen, added to the
page cache and removed from the page cache.
Fix by calling pipe_buf_release() right after the page was inserted into
the page cache. In this case the page has an elevated refcount so any
release function will know that the page isn't reusable.
Reported-by: Frank Dinoff <fdinoff@google.com>
Link: https://lore.kernel.org/r/CAAmZXrsGg2xsP1CK+cbuEMumtrqdvD-NKnWzhNcvn71RV3c1yw@mail.gmail.com/
Fixes: dd3bb14f44 ("fuse: support splice() writing to fuse device")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1811bc401a upstream.
After we drop i_data sem, we need to reload the ext4_ext_path
structure since the extent tree can change once i_data_sem is
released.
This addresses the BUG:
[52117.465187] ------------[ cut here ]------------
[52117.465686] kernel BUG at fs/ext4/extents.c:1756!
...
[52117.478306] Call Trace:
[52117.478565] ext4_ext_shift_extents+0x3ee/0x710
[52117.479020] ext4_fallocate+0x139c/0x1b40
[52117.479405] ? __do_sys_newfstat+0x6b/0x80
[52117.479805] vfs_fallocate+0x151/0x4b0
[52117.480177] ksys_fallocate+0x4a/0xa0
[52117.480533] __x64_sys_fallocate+0x22/0x30
[52117.480930] do_syscall_64+0x35/0x80
[52117.481277] entry_SYSCALL_64_after_hwframe+0x44/0xae
[52117.481769] RIP: 0033:0x7fa062f855ca
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20210903062748.4118886-4-yangerkun@huawei.com
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39fec6889d upstream.
Ext4 file system has default lazy inode table initialization setup once
it is mounted. However, it has issue on computing the next schedule time
that makes the timeout same amount in jiffies but different real time in
secs if with various HZ values. Therefore, fix by measuring the current
time in a more granular unit nanoseconds and make the next schedule time
independent of the HZ value.
Fixes: bfff68738f ("ext4: add support for lazy inode table initialization")
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20210902164412.9994-2-shaoyi@amazon.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0317c0e87 upstream.
When the timer instance was add into ack_list but was not currently in
process, the user could stop it via snd_timer_stop1() without delete it
from the ack_list. Then the user could free the timer instance and when
it was actually processed UAF occurred.
This issue could be reproduced via testcase snd_timer01 in ltp - running
several instances of that testcase at the same time.
What I actually met was that the ack_list of the timer broken and the
kernel went into deadloop with irqoff. That could be detected by
hardlockup detector on board or when we run it on qemu, we could use gdb
to dump the ack_list when the console has no response.
To fix this issue, we delete the timer instance from ack_list and
active_list unconditionally in snd_timer_stop1().
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211103033517.80531-1-wangwensheng4@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39173303c8 upstream.
The recent change in hda-intel driver to allow repeated probes
surfaced a problem that has been hidden until; the probe process in
the work calls azx_free() at the error path, and this skips the card
free process that eventually releases codec instances. As a result,
we get a kernel WARNING like:
snd_hda_intel 0000:00:1f.3: Cannot probe codecs, giving up
------------[ cut here ]------------
WARNING: CPU: 14 PID: 186 at sound/hda/hdac_bus.c:73
....
For fixing this, we need to call snd_card_free() instead of
azx_free(). Additionally, the device drvdata has to be cleared, as
the driver binding itself is still active. Then the PM and other
driver callbacks will ignore the procedure.
Fixes: c0f1886de7 ("ALSA: hda: intel: Allow repeatedly probing on codec configuration errors")
Reported-and-tested-by: Scott Branden <scott.branden@broadcom.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/063e2397-7edb-5f48-7b0d-618b938d9dd8@broadcom.com
Link: https://lore.kernel.org/r/20211110194633.19098-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f27b68906 upstream.
Adding the Line6 HX-Stomp XL USB_ID as it needs this fixed frequency
quirk as well.
The device is basically just the HX-Stomp with some more buttons on
the face. I've done some recording with it after adding it, and it
seems to function properly with this fix. The Midi features appear to
be working as well.
[ a coding style fix and patch reformat by tiwai ]
Signed-off-by: Jason Ormes <skryking@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211030200405.1358678-1-skryking@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55f261b73a upstream.
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in alloc_stream_buffers() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 63978ab3e3 ("sound: add Edirol UA-101 support")
Cc: stable@vger.kernel.org # 2.6.34
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211026095401.26522-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 861f92cb91 upstream.
Drivers that do not use the ctrl-framework use this function instead.
Fix the following issues:
- Do not check for multiple classes when getting the DEF_VAL.
- Return -EINVAL for request_api calls
- Default value cannot be changed, return EINVAL as soon as possible.
- Return the right error_idx
[If an error is found when validating the list of controls passed with
VIDIOC_G_EXT_CTRLS, then error_idx shall be set to ctrls->count to
indicate to userspace that no actual hardware was touched.
It would have been much nicer of course if error_idx could point to the
control index that failed the validation, but sadly that's not how the
API was designed.]
Fixes v4l2-compliance:
Control ioctls (Input 0):
warn: v4l2-test-controls.cpp(834): error_idx should be equal to count
warn: v4l2-test-controls.cpp(855): error_idx should be equal to count
fail: v4l2-test-controls.cpp(813): doioctl(node, VIDIOC_G_EXT_CTRLS, &ctrls)
test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL
Buffer ioctls (Input 0):
fail: v4l2-test-buffers.cpp(1994): ret != EINVAL && ret != EBADR && ret != ENOTTY
test Requests: FAIL
Cc: stable@vger.kernel.org
Fixes: 6fa6f831f0 ("media: v4l2-ctrls: add core request support")
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0887e9e152 upstream.
The mem-to-mem stateless decoder API specifies support for dynamic
resolution changes. In particular, the decoder should accept format
changes on the OUTPUT queue even when buffers have been allocated,
as long as it is not streaming.
Relax restrictions for S_FMT as described in the previous paragraph,
and as long as the codec format remains the same. This aligns it with
the Hantro and Cedrus decoders. This change was mostly based on commit
ae02d49493 ("media: hantro: Fix s_fmt for dynamic resolution changes").
Since rkvdec_s_fmt() is now just a wrapper around the output/capture
variants without any additional shared functionality, drop the wrapper
and call the respective functions directly.
Fixes: cd33c83044 ("media: rkvdec: Add the rkvdec driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
