[ Upstream commit 7de414a9dd ]
Most callers of pskb_trim_rcsum() simply drop the skb when
it fails, however, ip_check_defrag() still continues to pass
the skb up to stack. This is suspicious.
In ip_check_defrag(), after we learn the skb is an IP fragment,
passing the skb to callers makes no sense, because callers expect
fragments are defrag'ed on success. So, dropping the skb when we
can't defrag it is reasonable.
Note, prior to commit 88078d98d1, this is not a big problem as
checksum will be fixed up anyway. After it, the checksum is not
correct on failure.
Found this during code review.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 414dd6fb9a ]
The attribute IFLA_BOND_AD_ACTOR_SYSTEM is sent to user space having the
length of sizeof(bond->params.ad_actor_system) which is 8 byte. This
patch aligns the length to ETH_ALEN to have the same MAC address exposed
as using sysfs.
Fixes: f87fda00b6 ("bonding: prevent out of bound accesses")
Signed-off-by: Tobias Jungel <tobias.jungel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 58f5bbe331 ]
In dev_ethtool(), the eth command 'ethcmd' is firstly copied from the
use-space buffer 'useraddr' and checked to see whether it is
ETHTOOL_PERQUEUE. If yes, the sub-command 'sub_cmd' is further copied from
the user space. Otherwise, 'sub_cmd' is the same as 'ethcmd'. Next,
according to 'sub_cmd', a permission check is enforced through the function
ns_capable(). For example, the permission check is required if 'sub_cmd' is
ETHTOOL_SCOALESCE, but it is not necessary if 'sub_cmd' is
ETHTOOL_GCOALESCE, as suggested in the comment "Allow some commands to be
done by anyone". The following execution invokes different handlers
according to 'ethcmd'. Specifically, if 'ethcmd' is ETHTOOL_PERQUEUE,
ethtool_set_per_queue() is called. In ethtool_set_per_queue(), the kernel
object 'per_queue_opt' is copied again from the user-space buffer
'useraddr' and 'per_queue_opt.sub_command' is used to determine which
operation should be performed. Given that the buffer 'useraddr' is in the
user space, a malicious user can race to change the sub-command between the
two copies. In particular, the attacker can supply ETHTOOL_PERQUEUE and
ETHTOOL_GCOALESCE to bypass the permission check in dev_ethtool(). Then
before ethtool_set_per_queue() is called, the attacker changes
ETHTOOL_GCOALESCE to ETHTOOL_SCOALESCE. In this way, the attacker can
bypass the permission check and execute ETHTOOL_SCOALESCE.
This patch enforces a check in ethtool_set_per_queue() after the second
copy from 'useraddr'. If the sub-command is different from the one obtained
in the first copy in dev_ethtool(), an error code EINVAL will be returned.
Fixes: f38d138a7d ("net/ethtool: support set coalesce per queue")
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff002269a4 ]
The idx in vhost_vring_ioctl() was controlled by userspace, hence a
potential exploitation of the Spectre variant 1 vulnerability.
Fixing this by sanitizing idx before using it to index d->vqs.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b336decab2 ]
syzbot reported an use-after-free involving sctp_id2asoc. Dmitry Vyukov
helped to root cause it and it is because of reading the asoc after it
was freed:
CPU 1 CPU 2
(working on socket 1) (working on socket 2)
sctp_association_destroy
sctp_id2asoc
spin lock
grab the asoc from idr
spin unlock
spin lock
remove asoc from idr
spin unlock
free(asoc)
if asoc->base.sk != sk ... [*]
This can only be hit if trying to fetch asocs from different sockets. As
we have a single IDR for all asocs, in all SCTP sockets, their id is
unique on the system. An application can try to send stuff on an id
that matches on another socket, and the if in [*] will protect from such
usage. But it didn't consider that as that asoc may belong to another
socket, it may be freed in parallel (read: under another socket lock).
We fix it by moving the checks in [*] into the protected region. This
fixes it because the asoc cannot be freed while the lock is held.
Reported-by: syzbot+c7dd55d7aec49d48e49a@syzkaller.appspotmail.com
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b839b6cf9 ]
rtl_rx() and rtl_tx() are called only if the respective bits are set
in the interrupt status register. Under high load NAPI may not be
able to process all data (work_done == budget) and it will schedule
subsequent calls to the poll callback.
rtl_ack_events() however resets the bits in the interrupt status
register, therefore subsequent calls to rtl8169_poll() won't call
rtl_rx() and rtl_tx() - chip interrupts are still disabled.
Fix this by calling rtl_rx() and rtl_tx() independent of the bits
set in the interrupt status register. Both functions will detect
if there's nothing to do for them.
Fixes: da78dbff2e ("r8169: remove work from irq handler.")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit db4f1be3ca ]
Current handling of CHECKSUM_COMPLETE packets by the UDP stack is
incorrect for any packet that has an incorrect checksum value.
udp4/6_csum_init() will both make a call to
__skb_checksum_validate_complete() to initialize/validate the csum
field when receiving a CHECKSUM_COMPLETE packet. When this packet
fails validation, skb->csum will be overwritten with the pseudoheader
checksum so the packet can be fully validated by software, but the
skb->ip_summed value will be left as CHECKSUM_COMPLETE so that way
the stack can later warn the user about their hardware spewing bad
checksums. Unfortunately, leaving the SKB in this state can cause
problems later on in the checksum calculation.
Since the the packet is still marked as CHECKSUM_COMPLETE,
udp_csum_pull_header() will SUBTRACT the checksum of the UDP header
from skb->csum instead of adding it, leaving us with a garbage value
in that field. Once we try to copy the packet to userspace in the
udp4/6_recvmsg(), we'll make a call to skb_copy_and_csum_datagram_msg()
to checksum the packet data and add it in the garbage skb->csum value
to perform our final validation check.
Since the value we're validating is not the proper checksum, it's possible
that the folded value could come out to 0, causing us not to drop the
packet. Instead, we believe that the packet was checksummed incorrectly
by hardware since skb->ip_summed is still CHECKSUM_COMPLETE, and we attempt
to warn the user with netdev_rx_csum_fault(skb->dev);
Unfortunately, since this is the UDP path, skb->dev has been overwritten
by skb->dev_scratch and is no longer a valid pointer, so we end up
reading invalid memory.
This patch addresses this problem in two ways:
1) Do not use the dev pointer when calling netdev_rx_csum_fault()
from skb_copy_and_csum_datagram_msg(). Since this gets called
from the UDP path where skb->dev has been overwritten, we have
no way of knowing if the pointer is still valid. Also for the
sake of consistency with the other uses of
netdev_rx_csum_fault(), don't attempt to call it if the
packet was checksummed by software.
2) Add better CHECKSUM_COMPLETE handling to udp4/6_csum_init().
If we receive a packet that's CHECKSUM_COMPLETE that fails
verification (i.e. skb->csum_valid == 0), check who performed
the calculation. It's possible that the checksum was done in
software by the network stack earlier (such as Netfilter's
CONNTRACK module), and if that says the checksum is bad,
we can drop the packet immediately instead of waiting until
we try and copy it to userspace. Otherwise, we need to
mark the SKB as CHECKSUM_NONE, since the skb->csum field
no longer contains the full packet checksum after the
call to __skb_checksum_validate_complete().
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Fixes: c84d949057 ("udp: copy skb->truesize in the first cache line")
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30549aab14 ]
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.
When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().
Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.
Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.
Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6168562c8 ]
In ethtool_ioctl(), the ioctl command 'ethcmd' is checked through a switch
statement to see whether it is necessary to pre-process the ethtool
structure, because, as mentioned in the comment, the structure
ethtool_rxnfc is defined with padding. If yes, a user-space buffer 'rxnfc'
is allocated through compat_alloc_user_space(). One thing to note here is
that, if 'ethcmd' is ETHTOOL_GRXCLSRLALL, the size of the buffer 'rxnfc' is
partially determined by 'rule_cnt', which is actually acquired from the
user-space buffer 'compat_rxnfc', i.e., 'compat_rxnfc->rule_cnt', through
get_user(). After 'rxnfc' is allocated, the data in the original user-space
buffer 'compat_rxnfc' is then copied to 'rxnfc' through copy_in_user(),
including the 'rule_cnt' field. However, after this copy, no check is
re-enforced on 'rxnfc->rule_cnt'. So it is possible that a malicious user
race to change the value in the 'compat_rxnfc->rule_cnt' between these two
copies. Through this way, the attacker can bypass the previous check on
'rule_cnt' and inject malicious data. This can cause undefined behavior of
the kernel and introduce potential security risk.
This patch avoids the above issue via copying the value acquired by
get_user() to 'rxnfc->rule_cn', if 'ethcmd' is ETHTOOL_GRXCLSRLALL.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38b4f18d56 ]
gred_change_table_def() takes a pointer to TCA_GRED_DPS attribute,
and expects it will be able to interpret its contents as
struct tc_gred_sopt. Pass the correct gred attribute, instead of
TCA_OPTIONS.
This bug meant the table definition could never be changed after
Qdisc was initialized (unless whatever TCA_OPTIONS contained both
passed netlink validation and was a valid struct tc_gred_sopt...).
Old behaviour:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
RTNETLINK answers: Invalid argument
Now:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
Fixes: f62d6b936d ("[PKT_SCHED]: GRED: Use central VQ change procedure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ba4c566ba ]
The loop wants to skip previously dumped addresses, so loops until
current index >= saved index. If the message fills it wants to save
the index for the next address to dump - ie., the one that did not
fit in the current message.
Currently, it is incrementing the index counter before comparing to the
saved index, and then the saved index is off by 1 - it assumes the
current address is going to fit in the message.
Change the index handling to increment only after a succesful dump.
Fixes: 502a2ffd73 ("ipv6: convert idev_list to list macros")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a8e7aea95 ]
WHen an llc sock is added into the sk_laddr_hash of an llc_sap,
it is not marked with SOCK_RCU_FREE.
This causes that the sock could be freed while it is still being
read by __llc_lookup_established() with RCU read lock. sock is
refcounted, but with RCU read lock, nothing prevents the readers
getting a zero refcnt.
Fix it by setting SOCK_RCU_FREE in llc_sap_add_socket().
Reported-by: syzbot+11e05f04c15e03be5254@syzkaller.appspotmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee1abcf689 ]
Commit a61bbcf28a ("[NET]: Store skb->timestamp as offset to a base
timestamp") introduces a neighbour control buffer and zeroes it out in
ndisc_rcv(), as ndisc_recv_ns() uses it.
Commit f2776ff047 ("[IPV6]: Fix address/interface handling in UDP and
DCCP, according to the scoping architecture.") introduces the usage of the
IPv6 control buffer in protocol error handlers (e.g. inet6_iif() in
present-day __udp6_lib_err()).
Now, with commit b94f1c0904 ("ipv6: Use icmpv6_notify() to propagate
redirect, instead of rt6_redirect()."), we call protocol error handlers
from ndisc_redirect_rcv(), after the control buffer is already stolen and
some parts are already zeroed out. This implies that inet6_iif() on this
path will always return zero.
This gives unexpected results on UDP socket lookup in __udp6_lib_err(), as
we might actually need to match sockets for a given interface.
Instead of always claiming the control buffer in ndisc_rcv(), do that only
when needed.
Fixes: b94f1c0904 ("ipv6: Use icmpv6_notify() to propagate redirect, instead of rt6_redirect().")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fe5119e26 upstream.
Recently a check was added which prevents marking of routers with zero
source address, but for IPv6 that cannot happen as the relevant RFCs
actually forbid such packets:
RFC 2710 (MLDv1):
"To be valid, the Query message MUST
come from a link-local IPv6 Source Address, be at least 24 octets
long, and have a correct MLD checksum."
Same goes for RFC 3810.
And also it can be seen as a requirement in ipv6_mc_check_mld_query()
which is used by the bridge to validate the message before processing
it. Thus any queries with :: source address won't be processed anyway.
So just remove the check for zero IPv6 source address from the query
processing function.
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a2de63fd1 upstream.
Based on RFC 4541, 2.1.1. IGMP Forwarding Rules
The switch supporting IGMP snooping must maintain a list of
multicast routers and the ports on which they are attached. This
list can be constructed in any combination of the following ways:
a) This list should be built by the snooping switch sending
Multicast Router Solicitation messages as described in IGMP
Multicast Router Discovery [MRDISC]. It may also snoop
Multicast Router Advertisement messages sent by and to other
nodes.
b) The arrival port for IGMP Queries (sent by multicast routers)
where the source address is not 0.0.0.0.
We should not add the port to router list when receives query with source
0.0.0.0.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da15fc2fa9 ]
The Yocto build system does a 'make clean' when rebuilding due to
changed dependencies, and that consistently fails for me (causing the
whole BSP build to fail) with errors such as
| find: '[...]/perf/1.0-r9/perf-1.0/plugin_mac80211.so': No such file or directory
| find: '[...]/perf/1.0-r9/perf-1.0/plugin_mac80211.so': No such file or directory
| find: find: '[...]/perf/1.0-r9/perf-1.0/libtraceevent.a''[...]/perf/1.0-r9/perf-1.0/libtraceevent.a': No such file or directory: No such file or directory
|
[...]
| find: cannot delete '/mnt/xfs/devel/pil/yocto/tmp-glibc/work/wandboard-oe-linux-gnueabi/perf/1.0-r9/perf-1.0/util/.pstack.o.cmd': No such file or directory
Apparently (despite the comment), 'make clean' ends up launching
multiple sub-makes that all want to remove the same things - perhaps
this only happens in combination with a O=... parameter. In any case, we
don't lose much by explicitly disabling the parallelism for the clean
target, and it makes automated builds much more reliable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180705131527.19749-1-linux@rasmusvillemoes.dk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit ad8b1ffc3e.
From Florian Westphal <fw@strlen.de>:
It causes kernel crash for locally generated ipv6 fragments
when netfilter ipv6 defragmentation is used.
The faulty commit is not essential for -stable, it only
delays netns teardown for longer than needed when that netns
still has ipv6 frags queued. Much better than crash :-/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78a55d05de ]
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 298bc15b20 ]
Move the out-of-order and duplicate ACK packet check to before the call to
rxrpc_input_ackinfo() so that the receive window size and MTU size are only
checked in the latest ACK packet and don't regress.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c479d5f2c2 ]
We should only call the function to end a call's Tx phase if we rotated the
marked-last packet out of the transmission buffer.
Make rxrpc_rotate_tx_window() return an indication of whether it just
rotated the packet marked as the last out of the transmit buffer, carrying
the information out of the locked section in that function.
We can then check the return value instead of examining RXRPC_CALL_TX_LAST.
Fixes: 70790dbe3f ("rxrpc: Pass the last Tx packet marker in the annotation buffer")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eea96566c1 ]
The maximum CPU frequency for the i.MX53 QSB is 1GHz, so disable the
1.2GHz OPP. This makes the board work again with configs that have
cpufreq enabled like imx_v6_v7_defconfig on which the board stopped
working with the addition of cpufreq-dt support.
Fixes: 791f416608 ("ARM: dts: imx53: add cpufreq-dt support")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa90f9f955 ]
Recently, the subtest numbering was changed to start from 1. While it
is fine for displaying results, this should not be the case when the
subtests are actually invoked.
Typically, the subtests are stored in zero-indexed arrays and invoked
based on the index passed to the main test function. Since the index
now starts from 1, the second subtest in the array (index 1) gets
invoked instead of the first (index 0). This applies to all of the
following subtests but for the last one, the subtest always fails
because it does not meet the boundary condition of the subtest index
being lesser than the number of subtests.
This can be observed on powerpc64 and x86_64 systems running Fedora 28
as shown below.
Before:
# perf test "builtin clang support"
55: builtin clang support :
55.1: builtin clang compile C source to IR : Ok
55.2: builtin clang compile C source to ELF object : FAILED!
# perf test "LLVM search and compile"
38: LLVM search and compile :
38.1: Basic BPF llvm compile : Ok
38.2: kbuild searching : Ok
38.3: Compile source for BPF prologue generation : Ok
38.4: Compile source for BPF relocation : FAILED!
# perf test "BPF filter"
40: BPF filter :
40.1: Basic BPF filtering : Ok
40.2: BPF pinning : Ok
40.3: BPF prologue generation : Ok
40.4: BPF relocation checker : FAILED!
After:
# perf test "builtin clang support"
55: builtin clang support :
55.1: builtin clang compile C source to IR : Ok
55.2: builtin clang compile C source to ELF object : Ok
# perf test "LLVM search and compile"
38: LLVM search and compile :
38.1: Basic BPF llvm compile : Ok
38.2: kbuild searching : Ok
38.3: Compile source for BPF prologue generation : Ok
38.4: Compile source for BPF relocation : Ok
# perf test "BPF filter"
40: BPF filter :
40.1: Basic BPF filtering : Ok
40.2: BPF pinning : Ok
40.3: BPF prologue generation : Ok
40.4: BPF relocation checker : Ok
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Fixes: 9ef0112442 ("perf test: Fix subtest number when showing results")
Link: http://lkml.kernel.org/r/20180726171733.33208-1-sandipan@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2278446e2b ]
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f666675cd ]
When powering down a SDIO connected card during suspend, make sure to call
into the generic lbs_suspend() function before pulling the plug. This will
make sure the card is successfully deregistered from the system to avoid
communication to the card starving out.
Fixes: 7444a80929 ("libertas: fix suspend and resume for SDIO connected cards")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dc7c7badb ]
Before returning -EPERM we should release some resources, as already done
in the other error handling path of the function.
Fixes: d8f9cc328c ("IB/mlx4: Mark user MR as writable if actual virtual memory is writable")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c739969849 ]
Commit 42de82a8b5 previously attempted to fix this, and it did
correctly pad the MN and FR fields with spaces, but the SN field still
contains 0 bytes. The current code fills out the first 16 bytes with
hex2bin, leaving the last 4 bytes zeroed. Rather than adding a lot of
error-prone math to avoid overwriting SN twice, just set the whole thing
to spaces up front (it's only 20 bytes).
Fixes: 42de82a8b5 ("nvmet: don't report 0-bytes in serial number")
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11e9d7829d ]
bond_miimon_commit() handles the UP transition for each slave of a bond
in the case of MII. It is triggered 10 times per second for the default
MII Polling interval of 100ms. For device drivers that do not implement
__ethtool_get_link_ksettings() the call to bond_update_speed_duplex()
fails persistently while the MII status could remain UP. That is, in
this and other cases where the speed/duplex update keeps failing over a
longer period of time while the MII state is UP, a warning is printed
every MII polling interval.
To address these excessive warnings net_ratelimit() should be used.
Printing a warning once would not be sufficient since the call to
bond_update_speed_duplex() could recover to succeed and fail again
later. In that case there would be no new indication what went wrong.
Fixes: b5bf0f5b16 (bonding: correctly update link status during mii-commit phase)
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56f772279a ]
In failure path, we overwrite err to what vnic_rq_disable() returns. In
case it returns 0, enic_open() returns success in case of error.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Fixes: e8588e2685 ("enic: enable rq before updating rq descriptors")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfb61b5e3e ]
pmdp_invalidate() was changed to update the pmd atomically
(to not lose dirty/access bits) and return the original pmd
value.
However, in doing so, we lost a lot of the essential work that
set_pmd_at() does, namely to update hugepage mapping counts and
queuing up the batched TLB flush entry.
Thus we were not flushing entries out of the TLB when making
such PMD changes.
Fix this by abstracting the accounting work of set_pmd_at() out into a
separate function, and call it from pmdp_establish().
Fixes: a8e654f01c ("sparc64: update pmdp_invalidate() to return old pmd value")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45c8184c1b ]
Update the features after calling register_netdev() otherwise the
device features are not set up correctly and it not possible to change
the MTU of the device. After this change, the features reported by
ethtool match the device's features before the commit which introduced
the issue and it is possible to change the device's MTU.
Fixes: f599c64fdf ("xen-netfront: Fix race between device setup and open")
Reported-by: Liam Shepherd <liam@dancer.es>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52fda36d63 ]
Function bpf_fill_maxinsns11 is designed to not be able to be JITed on
x86_64. So, it fails when CONFIG_BPF_JIT_ALWAYS_ON=y, and
commit 09584b4067 ("bpf: fix selftests/bpf test_kmod.sh failure when
CONFIG_BPF_JIT_ALWAYS_ON=y") makes sure that failure is detected on that
case.
However, it does not fail on other architectures, which have a different
JIT compiler design. So, test_bpf has started to fail to load on those.
After this fix, test_bpf loads fine on both x86_64 and ppc64el.
Fixes: 09584b4067 ("bpf: fix selftests/bpf test_kmod.sh failure when CONFIG_BPF_JIT_ALWAYS_ON=y")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a30abaa40 ]
The commit c469652bb5 ("ALSA: hda - Use IS_REACHABLE() for
dependency on input") simplified the dependencies with IS_REACHABLE()
macro, but it broke due to its incorrect usage: it should have been
IS_REACHABLE(CONFIG_INPUT) instead of IS_REACHABLE(INPUT).
Fixes: c469652bb5 ("ALSA: hda - Use IS_REACHABLE() for dependency on input")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e78c38f6bd ]
In commit 30d6e0a419 ("futex: Remove duplicated code and fix undefined
behaviour"), I let FUTEX_WAKE_OP to fail on invalid op. Namely when op
should be considered as shift and the shift is out of range (< 0 or > 31).
But strace's test suite does this madness:
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xa0caffee);
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xbadfaced);
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xffffffff);
When I pick the first 0xa0caffee, it decodes as:
0x80000000 & 0xa0caffee: oparg is shift
0x70000000 & 0xa0caffee: op is FUTEX_OP_OR
0x0f000000 & 0xa0caffee: cmp is FUTEX_OP_CMP_EQ
0x00fff000 & 0xa0caffee: oparg is sign-extended 0xcaf = -849
0x00000fff & 0xa0caffee: cmparg is sign-extended 0xfee = -18
That means the op tries to do this:
(futex |= (1 << (-849))) == -18
which is completely bogus. The new check of op in the code is:
if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28)) {
if (oparg < 0 || oparg > 31)
return -EINVAL;
oparg = 1 << oparg;
}
which results obviously in the "Invalid argument" errno:
FAIL: futex
===========
futex(0x7fabd78bcffc, 0x5, 0xfacefeed, 0xb, 0x7fabd78bcffc, 0xa0caffee) = -1: Invalid argument
futex.test: failed test: ../futex failed with code 1
So let us soften the failure to print only a (ratelimited) message, crop
the value and continue as if it were right. When userspace keeps up, we
can switch this to return -EINVAL again.
[v2] Do not return 0 immediatelly, proceed with the cropped value.
Fixes: 30d6e0a419 ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3995bbf53b ]
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
fs/cifs/inode.c: In function ‘simple_hashstr’:
fs/cifs/inode.c:713: warning: integer constant is too large for ‘long’ type
Fixes: 7ea884c77e ("smb3: Fix root directory when server returns inode number of zero")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2aeb188354 ]
We're missing ctx lock when iterating children siblings
within the perf_read path for group reading. Following
race and crash can happen:
User space doing read syscall on event group leader:
T1:
perf_read
lock event->ctx->mutex
perf_read_group
lock leader->child_mutex
__perf_read_group_add(child)
list_for_each_entry(sub, &leader->sibling_list, group_entry)
----> sub might be invalid at this point, because it could
get removed via perf_event_exit_task_context in T2
Child exiting and cleaning up its events:
T2:
perf_event_exit_task_context
lock ctx->mutex
list_for_each_entry_safe(child_event, next, &child_ctx->event_list,...
perf_event_exit_event(child)
lock ctx->lock
perf_group_detach(child)
unlock ctx->lock
----> child is removed from sibling_list without any sync
with T1 path above
...
free_event(child)
Before the child is removed from the leader's child_list,
(and thus is omitted from perf_read_group processing), we
need to ensure that perf_read_group touches child's
siblings under its ctx->lock.
Peter further notes:
| One additional note; this bug got exposed by commit:
|
| ba5213ae6b ("perf/core: Correct event creation with PERF_FORMAT_GROUP")
|
| which made it possible to actually trigger this code-path.
Tested-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: ba5213ae6b ("perf/core: Correct event creation with PERF_FORMAT_GROUP")
Link: http://lkml.kernel.org/r/20170720141455.2106-1-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 900631ee6a ]
If L2TP_ATTR_OFFSET is set to a non-zero value in L2TPv3 tunnels, it
results in L2TPv3 packets being transmitted which might not be
compliant with the L2TPv3 RFC. This patch has l2tp ignore the offset
setting and send all packets with no offset.
In more detail:
L2TPv2 supports a variable offset from the L2TPv2 header to the
payload. The offset value is indicated by an optional field in the
L2TP header. Our L2TP implementation already detects the presence of
the optional offset and skips that many bytes when handling data
received packets. All transmitted packets are always transmitted with
no offset.
L2TPv3 has no optional offset field in the L2TPv3 packet
header. Instead, L2TPv3 defines optional fields in a "Layer-2 Specific
Sublayer". At the time when the original L2TP code was written, there
was talk at IETF of offset being implemented in a new Layer-2 Specific
Sublayer. A L2TP_ATTR_OFFSET netlink attribute was added so that this
offset could be configured and the intention was to allow it to be
also used to set the tx offset for L2TPv2. However, no L2TPv3 offset
was ever specified and the L2TP_ATTR_OFFSET parameter was forgotten
about.
Setting L2TP_ATTR_OFFSET results in L2TPv3 packets being transmitted
with the specified number of bytes padding between L2TPv3 header and
payload. This is not compliant with L2TPv3 RFC3931. This change
removes the configurable offset altogether while retaining
L2TP_ATTR_OFFSET for backwards compatibility. Any L2TP_ATTR_OFFSET
value is ignored.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f61dfff2f5 ]
With gcc 4.1.2:
drivers/iio/pressure/zpa2326.c: In function ‘zpa2326_wait_oneshot_completion’:
drivers/iio/pressure/zpa2326.c:868: warning: ‘ret’ may be used uninitialized in this function
When testing for "timeout < 0", timeout is already guaranteed to be
strict negative, so the branch is always taken, and ret is thus always
initialized. But (some version of) gcc is not smart enough to notice.
Remove the check to fix this.
As there is no other code in between assigning the error codes and
returning them, the error codes can be returned immediately, and the
intermediate variable can be dropped.
Drop the "else" to please checkpatch.
Fixes: e7215fe4d5 ("iio: pressure: zpa2326: report interrupted case as failure")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3976626ea3 ]
Commit 62e3a3e342 changed get_pages() to initialise
msm_gem_object::pages before trying to initialise msm_gem_object::sgt,
so that put_pages() would properly clean up pages in the failure
case.
However, this means that put_pages() now needs to check that
msm_gem_object::sgt is not null before trying to clean it up, and
this check was only applied to part of the cleanup code. Move
it all into the conditional block. (Strictly speaking we don't
need to make the kfree() conditional, but since we can't avoid
checking for null ourselves we may as well do so.)
Fixes: 62e3a3e342 ("drm/msm: fix leak in failed get_pages")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24e52b11e0 ]
When doing an incremental send, while processing an extent that changed
between the parent and send snapshots and that extent was an inline extent
in the parent snapshot, it's possible to access a memory region beyond
the end of leaf if the inline extent is very small and it is the first
item in a leaf.
An example scenario is described below.
The send snapshot has the following leaf:
leaf 33865728 items 33 free space 773 generation 46 owner 5
fs uuid ab7090d8-dafd-4fb9-9246-723b6d2e2fb7
chunk uuid 2d16478c-c704-4ab9-b574-68bff2281b1f
(...)
item 14 key (335 EXTENT_DATA 0) itemoff 3052 itemsize 53
generation 36 type 1 (regular)
extent data disk byte 12791808 nr 4096
extent data offset 0 nr 4096 ram 4096
extent compression 0 (none)
item 15 key (335 EXTENT_DATA 8192) itemoff 2999 itemsize 53
generation 36 type 1 (regular)
extent data disk byte 138170368 nr 225280
extent data offset 0 nr 225280 ram 225280
extent compression 0 (none)
(...)
And the parent snapshot has the following leaf:
leaf 31272960 items 17 free space 17 generation 31 owner 5
fs uuid ab7090d8-dafd-4fb9-9246-723b6d2e2fb7
chunk uuid 2d16478c-c704-4ab9-b574-68bff2281b1f
item 0 key (335 EXTENT_DATA 0) itemoff 3951 itemsize 44
generation 31 type 0 (inline)
inline extent data size 23 ram_bytes 613 compression 1 (zlib)
(...)
When computing the send stream, it is detected that the extent of inode
335, at file offset 0, and at fs/btrfs/send.c:is_extent_unchanged() we
grab the leaf from the parent snapshot and access the inline extent item.
However, before jumping to the 'out' label, we access the 'offset' and
'disk_bytenr' fields of the extent item, which should not be done for
inline extents since the inlined data starts at the offset of the
'disk_bytenr' field and can be very small. For example accessing the
'offset' field of the file extent item results in the following trace:
[ 599.705368] general protection fault: 0000 [#1] PREEMPT SMP
[ 599.706296] Modules linked in: btrfs psmouse i2c_piix4 ppdev acpi_cpufreq serio_raw parport_pc i2c_core evdev tpm_tis tpm_tis_core sg pcspkr parport tpm button su$
[ 599.709340] CPU: 7 PID: 5283 Comm: btrfs Not tainted 4.10.0-rc8-btrfs-next-46+ #1
[ 599.709340] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014
[ 599.709340] task: ffff88023eedd040 task.stack: ffffc90006658000
[ 599.709340] RIP: 0010:read_extent_buffer+0xdb/0xf4 [btrfs]
[ 599.709340] RSP: 0018:ffffc9000665ba00 EFLAGS: 00010286
[ 599.709340] RAX: db73880000000000 RBX: 0000000000000000 RCX: 0000000000000001
[ 599.709340] RDX: ffffc9000665ba60 RSI: db73880000000000 RDI: ffffc9000665ba5f
[ 599.709340] RBP: ffffc9000665ba30 R08: 0000000000000001 R09: ffff88020dc5e098
[ 599.709340] R10: 0000000000001000 R11: 0000160000000000 R12: 6db6db6db6db6db7
[ 599.709340] R13: ffff880000000000 R14: 0000000000000000 R15: ffff88020dc5e088
[ 599.709340] FS: 00007f519555a8c0(0000) GS:ffff88023f3c0000(0000) knlGS:0000000000000000
[ 599.709340] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 599.709340] CR2: 00007f1411afd000 CR3: 0000000235f8e000 CR4: 00000000000006e0
[ 599.709340] Call Trace:
[ 599.709340] btrfs_get_token_64+0x93/0xce [btrfs]
[ 599.709340] ? printk+0x48/0x50
[ 599.709340] btrfs_get_64+0xb/0xd [btrfs]
[ 599.709340] process_extent+0x3a1/0x1106 [btrfs]
[ 599.709340] ? btree_read_extent_buffer_pages+0x5/0xef [btrfs]
[ 599.709340] changed_cb+0xb03/0xb3d [btrfs]
[ 599.709340] ? btrfs_get_token_32+0x7a/0xcc [btrfs]
[ 599.709340] btrfs_compare_trees+0x432/0x53d [btrfs]
[ 599.709340] ? process_extent+0x1106/0x1106 [btrfs]
[ 599.709340] btrfs_ioctl_send+0x960/0xe26 [btrfs]
[ 599.709340] btrfs_ioctl+0x181b/0x1fed [btrfs]
[ 599.709340] ? trace_hardirqs_on_caller+0x150/0x1ac
[ 599.709340] vfs_ioctl+0x21/0x38
[ 599.709340] ? vfs_ioctl+0x21/0x38
[ 599.709340] do_vfs_ioctl+0x611/0x645
[ 599.709340] ? rcu_read_unlock+0x5b/0x5d
[ 599.709340] ? __fget+0x6d/0x79
[ 599.709340] SyS_ioctl+0x57/0x7b
[ 599.709340] entry_SYSCALL_64_fastpath+0x18/0xad
[ 599.709340] RIP: 0033:0x7f51945eec47
[ 599.709340] RSP: 002b:00007ffc21c13e98 EFLAGS: 00000202 ORIG_RAX: 0000000000000010
[ 599.709340] RAX: ffffffffffffffda RBX: ffffffff81096459 RCX: 00007f51945eec47
[ 599.709340] RDX: 00007ffc21c13f20 RSI: 0000000040489426 RDI: 0000000000000004
[ 599.709340] RBP: ffffc9000665bf98 R08: 00007f519450d700 R09: 00007f519450d700
[ 599.709340] R10: 00007f519450d9d0 R11: 0000000000000202 R12: 0000000000000046
[ 599.709340] R13: ffffc9000665bf78 R14: 0000000000000000 R15: 00007f5195574040
[ 599.709340] ? trace_hardirqs_off_caller+0x43/0xb1
[ 599.709340] Code: 29 f0 49 39 d8 4c 0f 47 c3 49 03 81 58 01 00 00 44 89 c1 4c 01 c2 4c 29 c3 48 c1 f8 03 49 0f af c4 48 c1 e0 0c 4c 01 e8 48 01 c6 <f3> a4 31 f6 4$
[ 599.709340] RIP: read_extent_buffer+0xdb/0xf4 [btrfs] RSP: ffffc9000665ba00
[ 599.762057] ---[ end trace fe00d7af61b9f49e ]---
This is because the 'offset' field starts at an offset of 37 bytes
(offsetof(struct btrfs_file_extent_item, offset)), has a length of 8
bytes and therefore attemping to read it causes a 1 byte access beyond
the end of the leaf, as the first item's content in a leaf is located
at the tail of the leaf, the item size is 44 bytes and the offset of
that field plus its length (37 + 8 = 45) goes beyond the item's size
by 1 byte.
So fix this by accessing the 'offset' and 'disk_bytenr' fields after
jumping to the 'out' label if we are processing an inline extent. We
move the reading operation of the 'disk_bytenr' field too because we
have the same problem as for the 'offset' field explained above when
the inline data is less then 8 bytes. The access to the 'generation'
field is also moved but just for the sake of grouping access to all
the fields.
Fixes: e1cbfd7bf6 ("Btrfs: send, fix file hole not being preserved due to inline extent")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 612601d001 ]
commit 9a9b811269 will cause core to fail UD QP from being destroyed
on ipoib unload, therefore cause resources leakage.
On pkey change event above patch modifies mgid before calling underlying
driver to detach it from QP. Drivers' detach_mcast() will fail to find
modified mgid it was never given to attach in a first place.
Core qp->usecnt will never go down, so ib_destroy_qp() will fail.
IPoIB driver actually does take care of new broadcast mgid based on new
pkey by destroying an old mcast object in ipoib_mcast_dev_flush())
....
if (priv->broadcast) {
rb_erase(&priv->broadcast->rb_node, &priv->multicast_tree);
list_add_tail(&priv->broadcast->list, &remove_list);
priv->broadcast = NULL;
}
...
then in restarted ipoib_macst_join_task() creating a new broadcast mcast
object, sending join request and on completion tells the driver to attach
to reinitialized QP:
...
if (!priv->broadcast) {
...
broadcast = ipoib_mcast_alloc(dev, 0);
...
memcpy(broadcast->mcmember.mgid.raw, priv->dev->broadcast + 4,
sizeof (union ib_gid));
priv->broadcast = broadcast;
...
Fixes: 9a9b811269 ("IB/ipoib: Update broadcast object if PKey value was changed in index 0")
Cc: stable@vger.kernel.org
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09f79fd49d ]
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit
96a39aed25 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed25 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a9910d7b6 ]
qla2x00_tmf_sp_done() now deletes the timer that will run
qla2x00_tmf_iocb_timeout(), but doesn't check whether the timer already
expired. Check the return value from del_timer() to avoid calling
complete() a second time.
Fixes: 4440e46d5d ("[SCSI] qla2xxx: Add IOCB Abort command asynchronous ...")
Fixes: 1514839b36 ("scsi: qla2xxx: Fix NULL pointer crash due to active ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
