[ Upstream commit a96ac8a004 ]
The ipq806x_gmac_probe() function enables the PTP clock but not the
appropriate interface clocks. This means that if the bootloader hasn't
done so attempting to bring up the interface will fail with an error
like:
[ 59.028131] ipq806x-gmac-dwmac 37600000.ethernet: Failed to reset the dma
[ 59.028196] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed
[ 59.034056] ipq806x-gmac-dwmac 37600000.ethernet eth1: stmmac_open: Hw setup failed
This patch, a slightly cleaned up version of one posted by Sergey
Sergeev in:
https://forum.openwrt.org/t/support-for-mikrotik-rb3011uias-rm/4064/257
correctly enables the clock; we have already configured the source just
before this.
Tested on a MikroTik RB3011.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79dde73cf9 ]
ugeth_quiesce/activate are used to halt the controller when there is a
link change that requires to reconfigure the mac.
The previous implementation called netif_device_detach(). This however
causes the initial activation of the netdevice to fail precisely because
it's detached. For details, see [1].
A possible workaround was the revert of commit
net: linkwatch: add check for netdevice being present to linkwatch_do_dev
However, the check introduced in the above commit is correct and shall be
kept.
The netif_device_detach() is thus replaced with
netif_tx_stop_all_queues() that prevents any tranmission. This allows to
perform mac config change required by the link change, without detaching
the corresponding netdevice and thus not preventing its initial
activation.
[1] https://lists.openwall.net/netdev/2020/01/08/201
Signed-off-by: Valentin Longchamp <valentin@longchamp.me>
Acked-by: Matteo Ghidoni <matteo.ghidoni@ch.abb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac8372f3b4 ]
On s390, the layout of normal and large ptes (i.e. pmds/puds) differs.
Therefore, set_huge_pte_at() does a conversion from a normal pte to
the corresponding large pmd/pud. So, when converting an empty pte, this
should result in an empty pmd/pud, which would return true for
pmd/pud_none().
However, after conversion we also mark the pmd/pud as large, and
therefore present. For empty ptes, this will result in an empty pmd/pud
that is also marked as large, and pmd/pud_none() would not return true.
There is currently no issue with this behaviour, as set_huge_pte_at()
does not seem to be called for empty ptes. It would be valid though, so
let's fix this by not marking empty ptes as large in set_huge_pte_at().
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add more arch page table helper
tests").
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef01cee2ee ]
In bmac_get_station_address, We're reading two bytes at a time from ROM,
but we do that six times, resulting in 12 bytes of read & writes. This
means we will write off the end of the six-byte destination buffer.
This change fixes the for-loop to only read/write six bytes.
Based on a proposed fix from Finn Thain <fthain@telegraphics.com.au>.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reported-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7110a26e5 ]
When building with Clang + -Wtautological-compare and
CONFIG_CPUMASK_OFFSTACK unset:
arch/x86/mm/mmio-mod.c:375:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL &&
^~~~~~~~~~~ ~~~~
arch/x86/mm/mmio-mod.c:405:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL || cpumask_weight(downed_cpus) == 0)
^~~~~~~~~~~ ~~~~
2 warnings generated.
Commit
f7e30f01a9 ("cpumask: Add helper cpumask_available()")
added cpumask_available() to fix warnings of this nature. Use that here
so that clang does not warn regardless of CONFIG_CPUMASK_OFFSTACK's
value.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/982
Link: https://lkml.kernel.org/r/20200408205323.44490-1-natechancellor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d4c797749 ]
Use a mutex to protect access to idev->msg_len, idev->buf, etc. which
are modified by both altr_i2c_xfer_msg() and altr_i2c_isr().
This is the minimal fix for easy backporting. A cleanup to remove the
spinlock will be added later.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 770f60586d ]
This patch fixes the following warning and few other instances of
traversal of evm_config_xattrnames list:
[ 32.848432] =============================
[ 32.848707] WARNING: suspicious RCU usage
[ 32.848966] 5.7.0-rc1-00006-ga8d5875ce5f0b #1 Not tainted
[ 32.849308] -----------------------------
[ 32.849567] security/integrity/evm/evm_main.c:231 RCU-list traversed in non-reader section!!
Since entries are only added to the list and never deleted, use
list_for_each_entry_lockless() instead of list_for_each_entry_rcu for
traversing the list. Also, add a relevant comment in evm_secfs.c to
indicate this fact.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org> (RCU viewpoint)
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 799587d573 ]
Elide invalid configuration EZNPS + ARCv2, triggered by a
make allyesconfig build.
Granted the root cause is in source code (asm/barrier.h) where we check
for ARCv2 before PLAT_EZNPS, but it is better to avoid such combinations
at onset rather then baking subtle nuances into code.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43900edf67 ]
As of today the ICCM and DCCM size checks are incorrectly using
mismatched units (KiB checked against bytes). The CONFIG_ARC_DCCM_SZ
and CONFIG_ARC_ICCM_SZ are in KiB, but the size calculated in
runtime and stored in cpu->dccm.sz and cpu->iccm.sz is in bytes.
Fix that.
Reported-by: Paul Greco <pmgreco@us.ibm.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4adfe5591 ]
A typical backtrace acquired from ftraced function currently looks like
the following (e.g. for "path_openat"):
arch_stack_walk+0x15c/0x2d8
stack_trace_save+0x50/0x68
stack_trace_call+0x15a/0x3b8
ftrace_graph_caller+0x0/0x1c
0x3e0007e3c98 <- ftraced function caller (should be do_filp_open+0x7c/0xe8)
do_open_execat+0x70/0x1b8
__do_execve_file.isra.0+0x7d8/0x860
__s390x_sys_execve+0x56/0x68
system_call+0xdc/0x2d8
Note random "0x3e0007e3c98" stack value as ftraced function caller. This
value causes either imprecise unwinder result or unwinding failure.
That "0x3e0007e3c98" comes from r14 of ftraced function stack frame, which
it haven't had a chance to initialize since the very first instruction
calls ftrace code ("ftrace_caller"). (ftraced function might never
save r14 as well). Nevertheless according to s390 ABI any function
is called with stack frame allocated for it and r14 contains return
address. "ftrace_caller" itself is called with "brasl %r0,ftrace_caller".
So, to fix this issue simply always save traced function caller onto
ftraced function stack frame.
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfda044533 ]
Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules
kernel: tpm tpm0: Operation Timed out
kernel: tpm tpm0: tpm_relinquish_locality: : error -1
Signed-off-by: fengsheng <fengsheng5@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Link: https://lore.kernel.org/r/1578019930-55858-1-git-send-email-kong.kongxinwei@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48e626ac85 ]
export_imc_mode_and_cmd() function which creates the debugfs interface
for imc-mode and imc-command, is invoked when each nest pmu units is
registered.
When the first nest pmu unit is registered, export_imc_mode_and_cmd()
creates 'imc' directory under `/debug/powerpc/`. In the subsequent
invocations debugfs_create_dir() function returns, since the directory
already exists.
The recent commit <c33d442328f55> (debugfs: make error message a bit
more verbose), throws a warning if we try to invoke
`debugfs_create_dir()` with an already existing directory name.
Address this warning by making the debugfs directory registration in
the opal_imc_counters_probe() function, i.e invoke
export_imc_mode_and_cmd() function from the probe function.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Tested-by: Nageswara R Sastry <nasastry@in.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191127072035.4283-1-anju@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 38152ea37d upstream.
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e72455b898 upstream.
Fix for non-working buttons on knock-off USB dongles for Sony
controllers. These USB dongles are used to connect older Sony DA/DS1/DS2
controllers via USB and are common on Amazon, AliExpress, etc. Without
the patch, the square, X, and circle buttons do not function. These
dongles used to work prior to kernel 4.10 but removing the global DS3
report fixup in commit e19a267b99 ("HID: sony: DS3 comply to Linux gamepad
spec") exposed the problem.
Many people reported the problem on the Ubuntu forums and are working
around the problem by falling back to the 4.9 hid-sony driver.
The problem stems from these dongles incorrectly reporting their button
count as 13 instead of 16. This patch fixes up the report descriptor by
changing the button report count to 16 and removing 3 padding bits.
Cc: stable@vger.kernel.org
Fixes: e19a267b99 ("HID: sony: DS3 comply to Linux gamepad spec")
Signed-off-by: Scott Shumate <scott.shumate@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8ef4b38cb ]
This reverts commit 9a9e97b2f1 ("cgroup: Add memory barriers to plug
cgroup_rstat_updated() race window").
The commit was added in anticipation of memcg rstat conversion which needed
synchronous accounting for the event counters (e.g. oom kill count). However,
the conversion didn't get merged due to percpu memory overhead concern which
couldn't be addressed at the time.
Unfortunately, the patch's addition of smp_mb() to cgroup_rstat_updated()
meant that every scheduling event now had to go through an additional full
barrier and Mel Gorman noticed it as 1% regression in netperf UDP_STREAM test.
There's no need to have this barrier in tree now and even if we need
synchronous accounting in the future, the right thing to do is separating that
out to a separate function so that hot paths which don't care about
synchronous behavior don't have to pay the overhead of the full barrier. Let's
revert.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Link: http://lkml.kernel.org/r/20200409154413.GK3818@techsingularity.net
Cc: v4.18+
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a068aab422 upstream.
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
Fixes: 07699f9a7c ("bonding: add sysfs /slave dir for bond slave devices.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15c9738589 upstream.
In function qlcnic_83xx_interrupt_test(), function
qlcnic_83xx_diag_alloc_res() is not handled by function
qlcnic_83xx_diag_free_res() after a call of the function
qlcnic_alloc_mbx_args() failed. Fix this issue by adding
a jump target "fail_mbx_args", and jump to this new target
when qlcnic_alloc_mbx_args() failed.
Fixes: b6b4316c8b ("qlcnic: Handle qlcnic_alloc_mbx_args() failure")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8056e8434 upstream.
We have logic to maintain network counters across resets by storing
the counters in bp->net_stats_prev before reset. But not all resets
will clear the counters. Certain resets that don't need to change
the number of rings do not clear the counters. The current logic
accumulates the counters before all resets, causing big jumps in
the counters after some resets, such as ethtool -G.
Fix it by only accumulating the counters during reset if the irq_re_init
parameter is set. The parameter signifies that all rings and interrupts
will be reset and that means that the counters will also be reset.
Reported-by: Vijayendra Suman <vijayendra.suman@oracle.com>
Fixes: b8875ca356 ("bnxt_en: Save ring statistics before reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c96ec5682 upstream.
For transport mode, when ipv6 nexthdr is set, the packet format might
be like:
----------------------------------------------------
| | dest | | | | ESP | ESP |
| IP6 hdr| opts.| ESP | TCP | Data | Trailer | ICV |
----------------------------------------------------
What it wants to get for x-proto in esp6_gso_encap() is the proto that
will be set in ESP nexthdr. So it should skip all ipv6 nexthdrs and
get the real transport protocol. Othersize, the wrong proto number
will be set into ESP nexthdr.
This patch is to skip all ipv6 nexthdrs by calling ipv6_skip_exthdr()
in esp6_gso_encap().
Fixes: 7862b4058b ("esp: Add gso handlers for esp4 and esp6")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c559f15ef upstream.
Dan Carpenter says: "Smatch complains that the value for "cmd" comes
from the network and can't be trusted."
Add pptp_msg_name() helper function that checks for the array boundary.
Fixes: f09943fefe ("[NETFILTER]: nf_conntrack/nf_nat: add PPTP helper port")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 703acd70f2 upstream.
Restore helper data size initialization and fix memcopy of the helper
data size.
Fixes: 157ffffeb5 ("netfilter: nfnetlink_cthelper: reject too large userspace allocation requests")
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a164b95ad6 upstream.
If IPSET_FLAG_SKIP_SUBCOUNTER_UPDATE is set, user requested to not
update counters in sub sets. Therefore IPSET_FLAG_SKIP_COUNTER_UPDATE
must be set, not unset.
Fixes: 6e01781d1c ("netfilter: ipset: set match: add support to match the counters")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9c284ec4b upstream.
Currently, using the bridge reject target with tagged packets
results in untagged packets being sent back.
Fix this by mirroring the vlan id as well.
Fixes: 85f5b3086a ("netfilter: bridge: add reject support")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 976eba8ab5 upstream.
In Commit dd9ee34440 ("vti4: Fix a ipip packet processing bug in
'IPCOMP' virtual tunnel"), it tries to receive IPIP packets in vti
by calling xfrm_input(). This case happens when a small packet or
frag sent by peer is too small to get compressed.
However, xfrm_input() will still get to the IPCOMP path where skb
sec_path is set, but never dropped while it should have been done
in vti_ipcomp4_protocol.cb_handler(vti_rcv_cb), as it's not an
ipcomp4 packet. This will cause that the packet can never pass
xfrm4_policy_check() in the upper protocol rcv functions.
So this patch is to call ip_tunnel_rcv() to process IPIP packets
instead.
Fixes: dd9ee34440 ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f981c57ffd upstream.
The ipip tunnel introduced in commit dd9ee34440 ("vti4: Fix a ipip
packet processing bug in 'IPCOMP' virtual tunnel") largely duplicated
the existing vti_input and vti_recv functions. Refactored to
deduplicate the common code.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6a23d85d0 upstream.
This patch is to fix a crash:
[ ] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ ] general protection fault: 0000 [#1] SMP KASAN PTI
[ ] RIP: 0010:ipv6_local_error+0xac/0x7a0
[ ] Call Trace:
[ ] xfrm6_local_error+0x1eb/0x300
[ ] xfrm_local_error+0x95/0x130
[ ] __xfrm6_output+0x65f/0xb50
[ ] xfrm6_output+0x106/0x46f
[ ] udp_tunnel6_xmit_skb+0x618/0xbf0 [ip6_udp_tunnel]
[ ] vxlan_xmit_one+0xbc6/0x2c60 [vxlan]
[ ] vxlan_xmit+0x6a0/0x4276 [vxlan]
[ ] dev_hard_start_xmit+0x165/0x820
[ ] __dev_queue_xmit+0x1ff0/0x2b90
[ ] ip_finish_output2+0xd3e/0x1480
[ ] ip_do_fragment+0x182d/0x2210
[ ] ip_output+0x1d0/0x510
[ ] ip_send_skb+0x37/0xa0
[ ] raw_sendmsg+0x1b4c/0x2b80
[ ] sock_sendmsg+0xc0/0x110
This occurred when sending a v4 skb over vxlan6 over ipsec, in which case
skb->protocol == htons(ETH_P_IPV6) while skb->sk->sk_family == AF_INET in
xfrm_local_error(). Then it will go to xfrm6_local_error() where it tries
to get ipv6 info from a ipv4 sk.
This issue was actually fixed by Commit 628e341f31 ("xfrm: make local
error reporting more robust"), but brought back by Commit 844d48746e
("xfrm: choose protocol family by skb protocol").
So to fix it, we should call xfrm6_local_error() only when skb->protocol
is htons(ETH_P_IPV6) and skb->sk->sk_family is AF_INET6.
Fixes: 844d48746e ("xfrm: choose protocol family by skb protocol")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed17b8d377 upstream.
This waring can be triggered simply by:
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 1 mark 0 mask 0x10 #[1]
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 2 mark 0 mask 0x1 #[2]
# ip xfrm policy update src 192.168.1.1/24 dst 192.168.1.2/24 dir in \
priority 2 mark 0 mask 0x10 #[3]
Then dmesg shows:
[ ] WARNING: CPU: 1 PID: 7265 at net/xfrm/xfrm_policy.c:1548
[ ] RIP: 0010:xfrm_policy_insert_list+0x2f2/0x1030
[ ] Call Trace:
[ ] xfrm_policy_inexact_insert+0x85/0xe50
[ ] xfrm_policy_insert+0x4ba/0x680
[ ] xfrm_add_policy+0x246/0x4d0
[ ] xfrm_user_rcv_msg+0x331/0x5c0
[ ] netlink_rcv_skb+0x121/0x350
[ ] xfrm_netlink_rcv+0x66/0x80
[ ] netlink_unicast+0x439/0x630
[ ] netlink_sendmsg+0x714/0xbf0
[ ] sock_sendmsg+0xe2/0x110
The issue was introduced by Commit 7cb8a93968 ("xfrm: Allow inserting
policies with matching mark and different priorities"). After that, the
policies [1] and [2] would be able to be added with different priorities.
However, policy [3] will actually match both [1] and [2]. Policy [1]
was matched due to the 1st 'return true' in xfrm_policy_mark_match(),
and policy [2] was matched due to the 2nd 'return true' in there. It
caused WARN_ON() in xfrm_policy_insert_list().
This patch is to fix it by only (the same value and priority) as the
same policy in xfrm_policy_mark_match().
Thanks to Yuehaibing, we could make this fix better.
v1->v2:
- check policy->mark.v == pol->mark.v only without mask.
Fixes: 7cb8a93968 ("xfrm: Allow inserting policies with matching mark and different priorities")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a204aef9fd upstream.
An use-after-free crash can be triggered when sending big packets over
vxlan over esp with esp offload enabled:
[] BUG: KASAN: use-after-free in ipv6_gso_pull_exthdrs.part.8+0x32c/0x4e0
[] Call Trace:
[] dump_stack+0x75/0xa0
[] kasan_report+0x37/0x50
[] ipv6_gso_pull_exthdrs.part.8+0x32c/0x4e0
[] ipv6_gso_segment+0x2c8/0x13c0
[] skb_mac_gso_segment+0x1cb/0x420
[] skb_udp_tunnel_segment+0x6b5/0x1c90
[] inet_gso_segment+0x440/0x1380
[] skb_mac_gso_segment+0x1cb/0x420
[] esp4_gso_segment+0xae8/0x1709 [esp4_offload]
[] inet_gso_segment+0x440/0x1380
[] skb_mac_gso_segment+0x1cb/0x420
[] __skb_gso_segment+0x2d7/0x5f0
[] validate_xmit_skb+0x527/0xb10
[] __dev_queue_xmit+0x10f8/0x2320 <---
[] ip_finish_output2+0xa2e/0x1b50
[] ip_output+0x1a8/0x2f0
[] xfrm_output_resume+0x110e/0x15f0
[] __xfrm4_output+0xe1/0x1b0
[] xfrm4_output+0xa0/0x200
[] iptunnel_xmit+0x5a7/0x920
[] vxlan_xmit_one+0x1658/0x37a0 [vxlan]
[] vxlan_xmit+0x5e4/0x3ec8 [vxlan]
[] dev_hard_start_xmit+0x125/0x540
[] __dev_queue_xmit+0x17bd/0x2320 <---
[] ip6_finish_output2+0xb20/0x1b80
[] ip6_output+0x1b3/0x390
[] ip6_xmit+0xb82/0x17e0
[] inet6_csk_xmit+0x225/0x3d0
[] __tcp_transmit_skb+0x1763/0x3520
[] tcp_write_xmit+0xd64/0x5fe0
[] __tcp_push_pending_frames+0x8c/0x320
[] tcp_sendmsg_locked+0x2245/0x3500
[] tcp_sendmsg+0x27/0x40
As on the tx path of vxlan over esp, skb->inner_network_header would be
set on vxlan_xmit() and xfrm4_tunnel_encap_add(), and the later one can
overwrite the former one. It causes skb_udp_tunnel_segment() to use a
wrong skb->inner_network_header, then the issue occurs.
This patch is to fix it by calling xfrm_output_gso() instead when the
inner_protocol is set, in which gso_segment of inner_protocol will be
done first.
While at it, also improve some code around.
Fixes: 7862b4058b ("esp: Add gso handlers for esp4 and esp6")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afcaf61be9 upstream.
For beet mode, when it's ipv6 inner address with nexthdrs set,
the packet format might be:
----------------------------------------------------
| outer | | dest | | | ESP | ESP |
| IP hdr | ESP | opts.| TCP | Data | Trailer | ICV |
----------------------------------------------------
The nexthdr from ESP could be NEXTHDR_HOP(0), so it should
continue processing the packet when nexthdr returns 0 in
xfrm_input(). Otherwise, when ipv6 nexthdr is set, the
packet will be dropped.
I don't see any error cases that nexthdr may return 0. So
fix it by removing the check for nexthdr == 0.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8874347066 upstream.
The intermediate result of the old term (4UL * 1024 * 1024 * 1024) is
4 294 967 296 or 0x100000000 which is no problem on 64 bit systems.
The patch does not change the later overall result of 0x100000 for
MAX_DMA32_PFN (after it has been shifted by PAGE_SHIFT). The new
calculation yields the same result, but does not require 64 bit
arithmetic.
On 32 bit systems the old calculation suffers from an arithmetic
overflow in that intermediate term in braces: 4UL aka unsigned long int
is 4 byte wide and an arithmetic overflow happens (the 0x100000000 does
not fit in 4 bytes), the in braces result is truncated to zero, the
following right shift does not alter that, so MAX_DMA32_PFN evaluates to
0 on 32 bit systems.
That wrong value is a problem in a comparision against MAX_DMA32_PFN in
the init code for swiotlb in pci_swiotlb_detect_4gb() to decide if
swiotlb should be active. That comparison yields the opposite result,
when compiling on 32 bit systems.
This was not possible before
1b7e03ef75 ("x86, NUMA: Enable emulation on 32bit too")
when that MAX_DMA32_PFN was first made visible to x86_32 (and which
landed in v3.0).
In practice this wasn't a problem, unless CONFIG_SWIOTLB is active on
x86-32.
However if one has set CONFIG_IOMMU_INTEL, since
c5a5dc4cbb ("iommu/vt-d: Don't switch off swiotlb if bounce page is used")
there's a dependency on CONFIG_SWIOTLB, which was not necessarily
active before. That landed in v5.4, where we noticed it in the fli4l
Linux distribution. We have CONFIG_IOMMU_INTEL active on both 32 and 64
bit kernel configs there (I could not find out why, so let's just say
historical reasons).
The effect is at boot time 64 MiB (default size) were allocated for
bounce buffers now, which is a noticeable amount of memory on small
systems like pcengines ALIX 2D3 with 256 MiB memory, which are still
frequently used as home routers.
We noticed this effect when migrating from kernel v4.19 (LTS) to v5.4
(LTS) in fli4l and got that kernel messages for example:
Linux version 5.4.22 (buildroot@buildroot) (gcc version 7.3.0 (Buildroot 2018.02.8)) #1 SMP Mon Nov 26 23:40:00 CET 2018
…
Memory: 183484K/261756K available (4594K kernel code, 393K rwdata, 1660K rodata, 536K init, 456K bss , 78272K reserved, 0K cma-reserved, 0K highmem)
…
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB: mapped [mem 0x0bb78000-0x0fb78000] (64MB)
The initial analysis and the suggested fix was done by user 'sourcejedi'
at stackoverflow and explicitly marked as GPLv2 for inclusion in the
Linux kernel:
https://unix.stackexchange.com/a/520525/50007
The new calculation, which does not suffer from that overflow, is the
same as for arch/mips now as suggested by Robin Murphy.
The fix was tested by fli4l users on round about two dozen different
systems, including both 32 and 64 bit archs, bare metal and virtualized
machines.
[ bp: Massage commit message. ]
Fixes: 1b7e03ef75 ("x86, NUMA: Enable emulation on 32bit too")
Reported-by: Alan Jenkins <alan.christopher.jenkins@gmail.com>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/q/520065/50007
Link: https://web.nettworks.org/bugs/browse/FFL-2560
Link: https://lkml.kernel.org/r/20200526175749.20742-1-post@lespocky.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
