[ Upstream commit 292f75ecff ]
All of the GPLLs in the MSM8998 Global Clock Controller are Fabia PLLs
and not generic alphas: this was producing bad effects over the entire
clock tree of MSM8998, where any GPLL child clock was declaring a false
clock rate, due to their parent also showing the same.
The issue resides in the calculation of the clock rate for the specific
Alpha PLL type, where Fabia has a different register layout; switching
the MSM8998 GPLLs to the correct Alpha Fabia PLL type fixes the rate
(calculation) reading. While at it, also make these PLLs fixed since
their rate is supposed to *never* be changed while the system runs, as
this would surely crash the entire SoC.
Now all the children of all the PLLs are also complying with their
specified clock table and system stability is improved.
Fixes: b5f5f525c5 ("clk: qcom: Add MSM8998 Global Clock Control (GCC) driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210114221059.483390-7-angelogioacchino.delregno@somainline.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 768d70e19b ]
dlpar_configure_connector() has two problems in its handling of
ibm,configure-connector's return status:
1. When the status is -2 (busy, call again), we call
ibm,configure-connector again immediately without checking whether
to schedule, which can result in monopolizing the CPU.
2. Extended delay status (9900..9905) goes completely unhandled,
causing the configuration to unnecessarily terminate.
Fix both of these issues by using rtas_busy_delay().
Fixes: ab519a011c ("powerpc/pseries: Kernel DLPAR Infrastructure")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210107025900.410369-1-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26783d74cc ]
The "req" struct is always added to the "wm831x->auxadc_pending" list,
but it's only removed from the list on the success path. If a failure
occurs then the "req" struct is freed but it's still on the list,
leading to a use after free.
Fixes: 78bb3688ea ("mfd: Support multiple active WM831x AUXADC conversions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5120bf0a5f ]
rxe_net.c sends packets at the IP layer with skb->data pointing at the IP
header but receives packets from a UDP tunnel with skb->data pointing at
the UDP header. On the loopback path this was not correctly accounted
for. This patch corrects for this by using sbk_pull() to strip the IP
header from the skb on received packets.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20210128182301.16859-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de5d7adb89 ]
Consider an amba driver with a .probe but without a .remove callback (e.g.
pl061_gpio_driver). The function amba_probe() is called to bind a device
and so dev_pm_domain_attach() and others are called. As there is no remove
callback amba_remove() isn't called at unbind time however and so calling
dev_pm_domain_detach() is missed and the pm domain keeps active.
To fix this always use the core driver callbacks and handle missing amba
callbacks there. For probe refuse registration as a driver without probe
doesn't make sense.
Fixes: 7cfe249475 ("ARM: AMBA: Add pclk support to AMBA bus infrastructure")
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210126165835.687514-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2acb909750 ]
It was observed that decompressor running on hardware implementing ARM v8.2
Load/Store Multiple Atomicity and Ordering Control (LSMAOC), say, as guest,
would stuck just after:
Uncompressing Linux... done, booting the kernel.
The reason is that it clears nTLSMD bit when disabling caches:
nTLSMD, bit [3]
When ARMv8.2-LSMAOC is implemented:
No Trap Load Multiple and Store Multiple to
Device-nGRE/Device-nGnRE/Device-nGnRnE memory.
0b0 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are trapped and
generate a stage 1 Alignment fault.
0b1 All memory accesses by A32 and T32 Load Multiple and Store
Multiple at EL1 or EL0 that are marked at stage 1 as
Device-nGRE/Device-nGnRE/Device-nGnRnE memory are not trapped.
This bit is permitted to be cached in a TLB.
This field resets to 1.
Otherwise:
Reserved, RES1
So as effect we start getting traps we are not quite ready for.
Looking into history it seems that mask used for SCTLR clear came from
the similar code for ARMv4, where bit[3] is the enable/disable bit for
the write buffer. That not applicable to ARMv7 and onwards, so retire
that bit from the masks.
Fixes: 7d09e85448 ("[ARM] 4393/2: ARMv7: Add uncompressing code for the new CPU Id format")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9236f57a9e ]
These are only used locally. It fixes these W=1 compile errors :
../arch/powerpc/kvm/powerpc.c:1521:5: error: no previous prototype for ‘kvmppc_get_vmx_dword’ [-Werror=missing-prototypes]
1521 | int kvmppc_get_vmx_dword(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1539:5: error: no previous prototype for ‘kvmppc_get_vmx_word’ [-Werror=missing-prototypes]
1539 | int kvmppc_get_vmx_word(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1557:5: error: no previous prototype for ‘kvmppc_get_vmx_hword’ [-Werror=missing-prototypes]
1557 | int kvmppc_get_vmx_hword(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~~
../arch/powerpc/kvm/powerpc.c:1575:5: error: no previous prototype for ‘kvmppc_get_vmx_byte’ [-Werror=missing-prototypes]
1575 | int kvmppc_get_vmx_byte(struct kvm_vcpu *vcpu, int index, u64 *val)
| ^~~~~~~~~~~~~~~~~~~
Fixes: acc9eb9305 ("KVM: PPC: Reimplement LOAD_VMX/STORE_VMX instruction mmio emulation with analyse_instr() input")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210104143206.695198-19-clg@kaod.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit def4cd43f5 ]
Currently, polling a umad device will always works, even if the device was
disassociated. A disassociated device should immediately return EPOLLERR
from poll(). Otherwise userspace is endlessly hung on poll() with no idea
that the device has been removed from the system.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20210125121339.837518-3-leon@kernel.org
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fc5461823 ]
MAD message received by the user has EINVAL error in all flows
including when the device is disassociated. That makes it impossible
for the applications to treat such flow differently.
Change it to return EIO, so the applications will be able to perform
disassociation recovery.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20210125121339.837518-2-leon@kernel.org
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89b0a4267 ]
Drop the call to msecs_to_jiffies(), as "HZ / fbdev->refresh_rate" is
already the number of jiffies to wait.
Fixes: 8992da44c6 ("auxdisplay: ht16k33: Driver for LED controller")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4993e1f947 ]
KEY_FLAG_KEEP is not meant to be passed to keyring_alloc() or key_alloc(),
as these only take KEY_ALLOC_* flags. KEY_FLAG_KEEP has the same value as
KEY_ALLOC_BYPASS_RESTRICTION, but fortunately only key_create_or_update()
uses it. LSMs using the key_alloc hook don't check that flag.
KEY_FLAG_KEEP is then ignored but fortunately (again) the root user cannot
write to the blacklist keyring, so it is not possible to remove a key/hash
from it.
Fix this by adding a KEY_ALLOC_SET_KEEP flag that tells key_alloc() to set
KEY_FLAG_KEEP on the new key. blacklist_init() can then, correctly, pass
this to keyring_alloc().
We can also use this in ima_mok_init() rather than setting the flag
manually.
Note that this doesn't fix an observable bug with the current
implementation but it is required to allow addition of new hashes to the
blacklist in the future without making it possible for them to be removed.
Fixes: 734114f878 ("KEYS: Add a system blacklist keyring")
Reported-by: Mickaël Salaün <mic@linux.microsoft.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Mickaël Salaün <mic@linux.microsoft.com>
cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04ef679591 ]
While comparing clocks between the H6 and H616, some of the M factor
ranges were found to be wrong: the manual says they are only covering
two bits [1:0], but our code had "5" in the number-of-bits field.
By writing 0xff into that register in U-Boot and via FEL, it could be
confirmed that bits [4:2] are indeed masked off, so the manual is right.
Change to number of bits in the affected clock's description.
Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210118000912.28116-1-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a5a75e5e9 ]
If the device tree is incorrectly configured, and attempts to
define a "no-map" reserved memory that overlaps with the kernel
data/code, the kernel would crash quickly after boot, with no
obvious clue about the nature of the issue.
For example, this would happen if we have the kernel mapped at
these addresses (from /proc/iomem):
40000000-41ffffff : System RAM
40080000-40dfffff : Kernel code
40e00000-411fffff : reserved
41200000-413e0fff : Kernel data
And we declare a no-map shared-dma-pool region at a fixed address
within that range:
mem_reserved: mem_region {
compatible = "shared-dma-pool";
reg = <0 0x40000000 0 0x01A00000>;
no-map;
};
To fix this, when removing memory regions at early boot (which is
what "no-map" regions do), we need to make sure that the memory
is not already reserved. If we do, __reserved_mem_reserve_reg
will throw an error:
[ 0.000000] OF: fdt: Reserved memory: failed to reserve memory
for node 'mem_region': base 0x0000000040000000, size 26 MiB
and the code that will try to use the region should also fail,
later on.
We do not do anything for non-"no-map" regions, as memblock
explicitly allows reserved regions to overlap, and the commit
that this fixes removed the check for that precise reason.
[ qperret: fixed conflicts caused by the usage of memblock_mark_nomap ]
Fixes: 094cb98179 ("of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20210115114544.1830068-3-qperret@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 035b73b2b3 ]
On Intel Tangier B0 and Anniedale the interrupt line, disregarding
to have different numbers, is shared between HSU DMA and UART IPs.
Thus on such SoCs we are expecting that IRQ handler is called in
UART driver only. hsu_pci_irq was handling the spurious interrupt
from HSU DMA by returning immediately. This wastes CPU time and
since HSU DMA and HSU UART interrupt occur simultaneously they race
to be handled causing delay to the HSU UART interrupt handling.
Fix this by disabling the interrupt entirely.
Fixes: 4831e0d905 ("serial: 8250_mid: handle interrupt correctly in DMA case")
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210112223749.97036-1-ftoth@exalondelft.nl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbc0ad004c ]
A 'irq_dispose_mapping()' call is missing in the remove function.
Add it.
This is needed to undo the 'irq_of_parse_and_map() call from the probe
function and already part of the error handling path of the probe function.
It was added in the probe function only in commit d3f620b2c4 ("fsldma:
simplify IRQ probing and handling")
Fixes: 77cd62e808 ("fsldma: allow Freescale Elo DMA driver to be compiled as a module")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201212160516.92515-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0312af1f9 ]
Prevent invalid (0, 0) inputs to hid-core's snto32() function.
Maybe it is just the dummy device here that is causing this, but
there are hundreds of calls to snto32(0, 0). Having n (bits count)
of 0 is causing the current UBSAN trap with a shift value of
0xffffffff (-1, or n - 1 in this function).
Either of the value to shift being 0 or the bits count being 0 can be
handled by just returning 0 to the caller, avoiding the following
complex shift + OR operations:
return value & (1 << (n - 1)) ? value | (~0U << n) : value;
Fixes: dde5845a52 ("[PATCH] Generic HID layer - code split")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: syzbot+1e911ad71dd4ea72e04a@syzkaller.appspotmail.com
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceeda328ed ]
The controller can only support up to 31 dummy cycles. If the command
requires more it falls back to using 31. This command is likely to fail
because the correct number of cycles are not waited upon. Rather than
silently issuing an incorrect command, fail loudly so the caller can get
a chance to find out the command can't be supported by the controller.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20201222184425.7028-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ebabde38 ]
The v3 file capabilities have a uid field that records the filesystem
uid of the root user of the user namespace the file capabilities are
valid in.
When someone is silly enough to have the same underlying uid as the
root uid of multiple nested containers a v3 filesystem capability can
be ambiguous.
In the spirit of don't do that then, forbid writing a v3 filesystem
capability if it is ambiguous.
Fixes: 8db6c34f1d ("Introduce v3 namespaced file capabilities")
Reviewed-by: Andrew G. Morgan <morgan@kernel.org>
Reviewed-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19646447ad ]
clang static analysis reports this problem
fs/jffs2/summary.c:794:31: warning: Use of memory after it is freed
c->summary->sum_list_head = temp->u.next;
^~~~~~~~~~~~
In jffs2_sum_write_data(), in a loop summary data is handles a node at
a time. When it has written out the node it is removed the summary list,
and the node is deleted. In the corner case when a
JFFS2_FEATURE_RWCOMPAT_COPY is seen, a call is made to
jffs2_sum_disable_collecting(). jffs2_sum_disable_collecting() deletes
the whole list which conflicts with the loop's deleting the list by parts.
To preserve the old behavior of stopping the write midway, bail out of
the loop after disabling summary collection.
Fixes: 6171586a7a ("[JFFS2] Correct handling of JFFS2_FEATURE_RWCOMPAT_COPY nodes.")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4208c398aa ]
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit integer. In the case where
l2nb is 32 or more this can lead to an overflow. Avoid this by shifting
the value 1LL instead.
Addresses-Coverity: ("Uninitentional integer overflow")
Fixes: b40c2e665c ("fs/jfs: TRIM support for JFS Filesystem")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f31e3386a4 ]
IMA allocates kernel virtual memory to carry forward the measurement
list, from the current kernel to the next kernel on kexec system call,
in ima_add_kexec_buffer() function. This buffer is not freed before
completing the kexec system call resulting in memory leak.
Add ima_buffer field in "struct kimage" to store the virtual address
of the buffer allocated for the IMA measurement list.
Free the memory allocated for the IMA measurement list in
kimage_file_post_load_cleanup() function.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Suggested-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Fixes: 7b8589cc29 ("ima: on soft reboot, save the measurement list")
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d14c65178 ]
IMA allocates kernel virtual memory to carry forward the measurement
list, from the current kernel to the next kernel on kexec system call,
in ima_add_kexec_buffer() function. In error code paths this memory
is not freed resulting in memory leak.
Free the memory allocated for the IMA measurement list in
the error code paths in ima_add_kexec_buffer() function.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Suggested-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Fixes: 7b8589cc29 ("ima: on soft reboot, save the measurement list")
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a53ab94eb6 ]
The length ('len' parameter) passed to crypto_ecdh_decode_key() is never
checked against the length encoded in the passed buffer ('buf'
parameter). This could lead to an out-of-bounds access when the passed
length is less than the encoded length.
Add a check to prevent that.
Fixes: 3c4b23901a ("crypto: ecdh - Add ECDH software support")
Signed-off-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
