[ Upstream commit 61d4f14094 ]
In dt-binding snps,dwmac.yaml, some properties under "snps,axi-config"
node are named without "axi_" prefix, but the driver expects the
prefix. Since the dt-binding has been there for a long time, we'd
better make driver match the binding for compatibility.
Fixes: afea03656a ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20221202161739.2203-1-jszhang@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63ff545af7 ]
The node returned by of_get_parent() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
end of of_pinctrl_get().
Fixes: 936ee2675e ("gpio/rockchip: add driver for rockchip gpio")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f2d71524b ]
A device might have a core quirk for NVME_QUIRK_IGNORE_DEV_SUBNQN
(such as Samsung X5) but it would still give a:
"missing or invalid SUBNQN field"
warning as core quirks are filled after calling nvme_init_subnqn. Fill
ctrl->quirks from struct core_quirks before calling nvme_init_subsystem
to fix this.
Tested on a Samsung X5.
Fixes: ab9e00cc72 ("nvme: track subsystems")
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d64aaf3f78 ]
Return -EOPNOTSUPP, when user requests l4_4_bytes for raw IP4 or
IP6 flow director filters. Flow director does not support filtering
on l4 bytes for PCTYPEs used by IP4 and IP6 filters.
Without this patch, user could create filters with l4_4_bytes fields,
which did not do any filtering on L4, but only on L3 fields.
Fixes: 36777d9fa2 ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0850197047 ]
After spawning max VFs on a PF, some VFs were not getting resources and
their MAC addresses were 0. This was caused by PF sleeping before flushing
HW registers which caused VIRTCHNL_VFR_VFACTIVE to not be set in time for
VF.
Fix by adding a sleep after hw flush.
Fixes: e4b433f4a7 ("i40e: reset all VFs in parallel when rebuilding PF")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82e0572b23 ]
During tx rings configuration default XPS queue config is set and
__I40E_TX_XPS_INIT_DONE is locked. __I40E_TX_XPS_INIT_DONE state is
cleared and set again with default mapping only during queues build,
it means after first setup or reset with queues rebuild. (i.e.
ethtool -L <interface> combined <number>) After other resets (i.e.
ethtool -t <interface>) XPS_INIT_DONE is not cleared and those default
maps cannot be set again. It results in cleared xps_cpus mapping
until queues are not rebuild or mapping is not set by user.
Add clearing __I40E_TX_XPS_INIT_DONE state during reset to let
the driver set xps_cpus to defaults again after it was cleared.
Fixes: 6f853d4f8e ("i40e: allow XPS with QoS enabled")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8b4fc1390 ]
The pp->indir[0] value comes from the user. It is passed to:
if (cpu_online(pp->rxq_def))
inside the mvneta_percpu_elect() function. It needs bounds checkeding
to ensure that it is not beyond the end of the cpu bitmap.
Fixes: cad5d847a0 ("net: mvneta: Fix the CPU choice in mvneta_percpu_elect")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d50b7914fa ]
A NAPI is setup for each network sring to poll data to kernel
The sring with source host is destroyed before live migration and
new sring with target host is setup after live migration.
The NAPI for the old sring is not deleted until setup new sring
with target host after migration. With busy_poll/busy_read enabled,
the NAPI can be polled before got deleted when resume VM.
BUG: unable to handle kernel NULL pointer dereference at
0000000000000008
IP: xennet_poll+0xae/0xd20
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
Call Trace:
finish_task_switch+0x71/0x230
timerqueue_del+0x1d/0x40
hrtimer_try_to_cancel+0xb5/0x110
xennet_alloc_rx_buffers+0x2a0/0x2a0
napi_busy_loop+0xdb/0x270
sock_poll+0x87/0x90
do_sys_poll+0x26f/0x580
tracing_map_insert+0x1d4/0x2f0
event_hist_trigger+0x14a/0x260
finish_task_switch+0x71/0x230
__schedule+0x256/0x890
recalc_sigpending+0x1b/0x50
xen_sched_clock+0x15/0x20
__rb_reserve_next+0x12d/0x140
ring_buffer_lock_reserve+0x123/0x3d0
event_triggers_call+0x87/0xb0
trace_event_buffer_commit+0x1c4/0x210
xen_clocksource_get_cycles+0x15/0x20
ktime_get_ts64+0x51/0xf0
SyS_ppoll+0x160/0x1a0
SyS_ppoll+0x160/0x1a0
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x41/0xa6
...
RIP: xennet_poll+0xae/0xd20 RSP: ffffb4f041933900
CR2: 0000000000000008
---[ end trace f8601785b354351c ]---
xen frontend should remove the NAPIs for the old srings before live
migration as the bond srings are destroyed
There is a tiny window between the srings are set to NULL and
the NAPIs are disabled, It is safe as the NAPI threads are still
frozen at that time
Signed-off-by: Lin Liu <lin.liu@citrix.com>
Fixes: 4ec2411980 ([NET]: Do not check netif_running() and carrier state in ->poll())
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbf33f5ac7 ]
In otx2_init_tc(), if rhashtable_init() failed, it does not free
tc->tc_entries_bitmap which is allocated in otx2_tc_alloc_ent_bitmap().
Fixes: 2e2a8126ff ("octeontx2-pf: Unify flow management variables")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 165df24186 ]
If phy_device_register() or fwnode_mdiobus_phy_device_register()
fail, phy_device_free() is called, the device refcount is decreased
to 0, then fwnode_handle_put() will be called in phy_device_release(),
but in the error path, fwnode_handle_put() has already been called,
so set fwnode to NULL after fwnode_handle_put() in the error path to
avoid double put.
Fixes: cdde156011 ("net: mdiobus: fix unbalanced node reference count")
Reported-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfaa202a73 ]
Rework error handling as preparation for PSE patch. This patch should
make it easier to extend this function.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 165df24186 ("net: mdiobus: fix double put fwnode in the error path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f427ac7b ]
A loop for reading MISTAT register continues while regmap_read() fails
and (mistat & BUSY), but if regmap_read() fails a value of mistat is
undefined.
The patch proposes to check for BUSY flag only when regmap_read()
succeed. Compile test only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d70e53262f ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 167b3f2dcc ]
In functions regmap_encx24j600_phy_reg_read() and
regmap_encx24j600_phy_reg_write() in the conditions of the waiting
cycles for filling the variable 'ret' it is necessary to add parentheses
to prevent wrong assignment due to logical operations precedence.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d70e53262f ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3d72d3135 ]
Kernel fault injection test reports null-ptr-deref as follows:
BUG: kernel NULL pointer dereference, address: 0000000000000008
RIP: 0010:cfg802154_netdev_notifier_call+0x120/0x310 include/linux/list.h:114
Call Trace:
<TASK>
raw_notifier_call_chain+0x6d/0xa0 kernel/notifier.c:87
call_netdevice_notifiers_info+0x6e/0xc0 net/core/dev.c:1944
unregister_netdevice_many_notify+0x60d/0xcb0 net/core/dev.c:1982
unregister_netdevice_queue+0x154/0x1a0 net/core/dev.c:10879
register_netdevice+0x9a8/0xb90 net/core/dev.c:10083
ieee802154_if_add+0x6ed/0x7e0 net/mac802154/iface.c:659
ieee802154_register_hw+0x29c/0x330 net/mac802154/main.c:229
mcr20a_probe+0xaaa/0xcb1 drivers/net/ieee802154/mcr20a.c:1316
ieee802154_if_add() allocates wpan_dev as netdev's private data, but not
init the list in struct wpan_dev. cfg802154_netdev_notifier_call() manage
the list when device register/unregister, and may lead to null-ptr-deref.
Use INIT_LIST_HEAD() on it to initialize it correctly.
Fixes: fcf39e6e88 ("ieee802154: add wpan_dev_list")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221130091705.1831140-1-weiyongjun@huaweicloud.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3957c7eb ]
bt_init() calls bt_leds_init() to register led, but if it fails later,
bt_leds_cleanup() is not called to unregister it.
This can cause panic if the argument "bluetooth-power" in text is freed
and then another led_trigger_register() tries to access it:
BUG: unable to handle page fault for address: ffffffffc06d3bc0
RIP: 0010:strcmp+0xc/0x30
Call Trace:
<TASK>
led_trigger_register+0x10d/0x4f0
led_trigger_register_simple+0x7d/0x100
bt_init+0x39/0xf7 [bluetooth]
do_one_initcall+0xd0/0x4e0
Fixes: e64c97b53b ("Bluetooth: Add combined LED trigger for controller power")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 747da1308b ]
hci_get_route() takes reference, we should use hci_dev_put() to release
it when not need anymore.
Fixes: 6b8d4a6a03 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 409e8ec8c5 ]
Commit 39f9895a00 ("vmxnet3: add support for 32 Tx/Rx queues")
added support for 32Tx/Rx queues. As a part of this patch, intrConf
structure was extended to incorporate increased queues.
This patch fixes the issue where incorrect reference is being used.
Fixes: 39f9895a00 ("vmxnet3: add support for 32 Tx/Rx queues")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40b8c2a1af ]
Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the
pathc did not report correctly the encapsulated packet which is
LRO'ed by the hypervisor.
This patch fixes this issue by using correct callback for the LRO'ed
encapsulated packet.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3d6b1bf85 ]
Cheap monitors sometimes advertise YUV modes they don't really have
(HDMI specification mandates YUV support so even monitors without actual
support will often wrongfully advertise it) which results in YUV matches
and user forum complaints of a red tint to light colour display areas in
common desktop environments.
Moving the default RGB fall-back before YUV selection results in RGB
mode matching in most cases, reducing complaints.
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Guillaume BRUN <the.cheaterman@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116143523.2126-1-the.cheaterman@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 421f8663b3 ]
commit 8d820bc9d1 ("net: broadcom: Fix BCMGENET Kconfig") fixes the build
that contain 99addbe31f ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
and enable BCMGENET=y but PTP_1588_CLOCK_OPTIONAL=m, which otherwise
leads to a link failure. However this may trigger a runtime failure.
Fix the original issue by propagating the PTP_1588_CLOCK_OPTIONAL dependency
of BROADCOM_PHY down to BCMGENET.
Fixes: 8d820bc9d1 ("net: broadcom: Fix BCMGENET Kconfig")
Fixes: 99addbe31f ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221125115003.30308-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28e96556ba ]
Without this change, the interrupt test fail with MSI-X environment:
$ sudo ethtool -t enp0s2 offline
[ 43.921783] igb 0000:00:02.0: offline testing starting
[ 44.855824] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Down
[ 44.961249] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 51.272202] igb 0000:00:02.0: testing shared interrupt
[ 56.996975] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 4
Loopback test (offline) 0
Link test (on/offline) 0
Here, "4" means an expected interrupt was not delivered.
To fix this, route IRQs correctly to the first MSI-X vector by setting
IVAR_MISC. Also, set bit 0 of EIMS so that the vector will not be
masked. The interrupt test now runs properly with this change:
$ sudo ethtool -t enp0s2 offline
[ 42.762985] igb 0000:00:02.0: offline testing starting
[ 50.141967] igb 0000:00:02.0: testing shared interrupt
[ 56.163957] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Fixes: 4eefa8f013 ("igb: add single vector msi-x testing to interrupt test")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eed913f691 ]
e1000_xmit_frame is expected to stop the queue and dispatch frames to
hardware if there is not sufficient space for the next frame in the
buffer, but sometimes it failed to do so because the estimated maximum
size of frame was wrong. As the consequence, the later invocation of
e1000_xmit_frame failed with NETDEV_TX_BUSY, and the frame in the buffer
remained forever, resulting in a watchdog failure.
This change fixes the estimated size by making it match with the
condition for NETDEV_TX_BUSY. Apparently, the old estimation failed to
account for the following lines which determines the space requirement
for not causing NETDEV_TX_BUSY:
```
/* reserve a descriptor for the offload context */
if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
count++;
count++;
count += DIV_ROUND_UP(len, adapter->tx_fifo_limit);
```
This issue was found when running http-stress02 test included in Linux
Test Project 20220930 on QEMU with the following commandline:
```
qemu-system-x86_64 -M q35,accel=kvm -m 8G -smp 8
-drive if=virtio,format=raw,file=root.img,file.locking=on
-device e1000e,netdev=netdev
-netdev tap,script=ifup,downscript=no,id=netdev
```
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fecdb9f6 ]
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: f942a7de04 ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c11586450 ]
According to the description in ti-sn65dsi86's datasheet:
CHA_HSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
CHA_VSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (Default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.
We should only set these bits when the polarity is negative.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125104558.84616-1-eddy.zhang@rock-chips.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e24c54da2 ]
The struct cas_control embeds multiple generic SPI structures and we
have to make sure these structures are initialized to default values.
This driver does not set all attributes. When using kmalloc before some
attributes were not initialized and contained random data which caused
random crashes at bootup.
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20221121002201.1339636-1-hauke@hauke-m.de
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97d4d394b5 ]
Embarrassingly, nft_pipapo_insert() checked for interval validity in
the first field only.
The start_p and end_p pointers were reset to key data from the first
field at every iteration of the loop which was supposed to go over
the set fields.
Fixes: 3c4287f620 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec851b2308 ]
Here is a backtrace report about memory leak detected in
gpiochip_setup_dev():
unreferenced object 0xffff88810b406400 (size 512):
comm "python3", pid 1682, jiffies 4295346908 (age 24.090s)
backtrace:
kmalloc_trace
device_add device_private_init at drivers/base/core.c:3361
(inlined by) device_add at drivers/base/core.c:3411
cdev_device_add
gpiolib_cdev_register
gpiochip_setup_dev
gpiochip_add_data_with_key
gcdev_register() & gcdev_unregister() would call device_add() &
device_del() (no matter CONFIG_GPIO_CDEV is enabled or not) to
register/unregister device.
However, if device_add() succeeds, some resource (like
struct device_private allocated by device_private_init())
is not released by device_del().
Therefore, after device_add() succeeds by gcdev_register(), it
needs to call put_device() to release resource in the error handle
path.
Here we move forward the register of release function, and let it
release every piece of resource by put_device() instead of kfree().
While at it, fix another subtle issue, i.e. when gc->ngpio is equal
to 0, we still call kcalloc() and, in case of further error, kfree()
on the ZERO_PTR pointer, which is not NULL. It's not a bug per se,
but rather waste of the resources and potentially wrong expectation
about contents of the gdev->descs variable.
Fixes: 159f3cd92f ("gpiolib: Defer gpio device setup until after gpiolib initialization")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dbd1ab205 ]
Several drivers read the 'ngpios' device property on their own, but
since it's defined as a standard GPIO property in the device tree bindings
anyway, it's a good candidate for generalization. If the driver didn't
set its gc->ngpio, try to read the 'ngpios' property from the GPIO
device's firmware node before bailing out.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b2308 ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5ab49cd3d ]
Drop unneeded whitespaces and put the variables of the same type
together for consistency with the rest of the code.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b2308 ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9ad6645a9d upstream.
The Acer Aspire Switch V 10 (SW5-017)'s keyboard-dock uses the same
ITE controller setup as other Acer Switch 2-in-1's.
This needs special handling for the wifi on/off toggle hotkey as well as
to properly report touchpad on/off keypresses.
Add the USB-ids for the SW5-017's keyboard-dock with a quirk setting of
QUIRK_TOUCHPAD_ON_OFF_REPORT to fix both issues.
Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec61b41918 upstream.
Syzbot reported shift-out-of-bounds in hid_report_raw_event.
microsoft 0003:045E:07DA.0001: hid_field_extract() called with n (128) >
32! (swapper/0)
======================================================================
UBSAN: shift-out-of-bounds in drivers/hid/hid-core.c:1323:20
shift exponent 127 is too large for 32-bit type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted
6.1.0-rc4-syzkaller-00159-g4bbf3422df78 #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS
Google 10/26/2022
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1e3/0x2cb lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x3a6/0x420 lib/ubsan.c:322
snto32 drivers/hid/hid-core.c:1323 [inline]
hid_input_fetch_field drivers/hid/hid-core.c:1572 [inline]
hid_process_report drivers/hid/hid-core.c:1665 [inline]
hid_report_raw_event+0xd56/0x18b0 drivers/hid/hid-core.c:1998
hid_input_report+0x408/0x4f0 drivers/hid/hid-core.c:2066
hid_irq_in+0x459/0x690 drivers/hid/usbhid/hid-core.c:284
__usb_hcd_giveback_urb+0x369/0x530 drivers/usb/core/hcd.c:1671
dummy_timer+0x86b/0x3110 drivers/usb/gadget/udc/dummy_hcd.c:1988
call_timer_fn+0xf5/0x210 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers+0x76a/0x980 kernel/time/timer.c:1790
run_timer_softirq+0x63/0xf0 kernel/time/timer.c:1803
__do_softirq+0x277/0x75b kernel/softirq.c:571
__irq_exit_rcu+0xec/0x170 kernel/softirq.c:650
irq_exit_rcu+0x5/0x20 kernel/softirq.c:662
sysvec_apic_timer_interrupt+0x91/0xb0 arch/x86/kernel/apic/apic.c:1107
======================================================================
If the size of the integer (unsigned n) is bigger than 32 in snto32(),
shift exponent will be too large for 32-bit type 'int', resulting in a
shift-out-of-bounds bug.
Fix this by adding a check on the size of the integer (unsigned n) in
snto32(). To add support for n greater than 32 bits, set n to 32, if n
is greater than 32.
Reported-by: syzbot+8b1641d2f14732407e23@syzkaller.appspotmail.com
Fixes: dde5845a52 ("[PATCH] Generic HID layer - code split")
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d180b64961 upstream.
If an empty buf is received, lbuf is also empty. So lbuf is
accessed by index -1.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: f31a2de3fe ("HID: hid-lg4ff: Allow switching of Logitech gaming wheels between compatibility modes")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6d910a89a upstream.
Some additional USB mouse devices are needing ALWAYS_POLL quirk without
which they disconnect and reconnect every 60s.
Add below devices to the known quirk list.
CHERRY VID 0x046a, PID 0x000c
MICROSOFT VID 0x045e, PID 0x0783
PRIMAX VID 0x0461, PID 0x4e2a
Signed-off-by: Ankit Patel <anpatel@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8bac7f9fd upstream.
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Fixes: 38fbe91f22 ("net: dsa: sja1105: configure the multicast policers, if present")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Nicolae Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20221207132347.38698-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
