This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.12 please pull the following:
- Rafal continues to add support for the 4906/4908 SoC family and adds
a Device Tree for the Netgear R8000P router (4906-based), describes
the NAND controller of the 4908 more appropriately (based on the older
63138 DSL SoC), describes the 4908 PCIe reset controller, internal
Ethernet switch (Starfighter 2 switch) and finally the Power
Management Bus (PMB)
- Scott removes all of the SATA-related Device Tree nodes since SATA
is unused on the Stingray product line
* tag 'arm-soc/for-5.12/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: Remove SATA from Stingray
arm64: dts: broadcom: bcm4908: describe PMB block
arm64: dts: broadcom: bcm4908: describe internal switch
arm64: dts: broadcom: bcm4908: describe PCIe reset controller
arm64: dts: broadcom: bcm4908: use proper NAND binding
arm64: dts: broadcom: bcm4908: add BCM4906 Netgear R8000P DTS files
dt-bindings: arm: bcm: document Netgear R8000P binding
Link: https://lore.kernel.org/r/20210131221721.685974-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.12, please pull the following:
- Dave adds a proper compatile string for the DSI1 panel on 2711
(Raspberry Pi 4) to permit adequate driver differentiation
- Nicolas declares reserved memory regions filed by the Rasbperry Pi
bootloader to indicate the running system configuration
- Maxime declares the BSC (HDMI I2C controller) and CEC interrupt
controllers
- Stanislav fixes a tab vs. space issue in the BCM21664 DTS
* tag 'arm-soc/for-5.12/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711: Add the CEC interrupt controller
ARM: dts: bcm21664: Replace spaces with a tab
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add reserved memory template to hold firmware configuration
ARM: dts: bcm2711: Use compatible string for BCM2711 DSI1
Link: https://lore.kernel.org/r/20210131221721.685974-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The R_INTC block controls more than just the NMI, and it is a different
hardware block than the NMI INTC found in some other Allwinner SoCs, so
the label "nmi_intc" is inaccurate. Name it "r_intc" to match the
compatible and to match the few references in the vendor documentation.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210118055040.21910-6-samuel@sholland.org
While the USB PHY Device Tree mandates that the name of the ID detect pin
should be usb0_id_det-gpios, a significant number of device tree use
usb0_id_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-12-maxime@cerno.tech
dt-bindings: tegra: Changes for v5.12-rc1
Exposed a new QSPI clock to DT on Tegra210 and documents the eMMC SKU of
the Jetson Xavier NX board.
* tag 'tegra-for-5.12-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: arm: tegra: Document Jetson Xavier NX eMMC SKU
Link: https://lore.kernel.org/r/20210129193254.3610492-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v5.12-rc1
Fixes an issue with HDA codec detection by properly wiring up the
power-domain for the HDA controller. This also fixes one of the USB-C
ports on Jetson AGX Xavier and enables support for audio on various
Tegra210, Tegra186 and Tegra194 boards. The Jetson Nano and Jetson TX1
also gain QSPI support.
* tag 'tegra-for-5.12-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Audio graph sound card for Jetson AGX Xavier
arm64: tegra: Audio graph sound card for Jetson TX2
Revert "arm64: tegra: Disable the ACONNECT for Jetson TX2"
arm64: tegra: Add RT5658 device entry
arm64: tegra: Add support for Jetson Xavier NX with eMMC
arm64: tegra: Prepare for supporting the Jetson Xavier NX with eMMC
arm64: tegra: Enable QSPI on Jetson Xavier NX
arm64: tegra: Add QSPI nodes on Tegra194
arm64: tegra: Enable QSPI on Jetson Nano
arm64: tegra: Audio graph sound card for Jetson Nano and TX1
arm64: tegra: Audio graph header for Tegra210
arm64: tegra: Order nodes alphabetically on Tegra210
arm64: tegra: Enable Jetson-Xavier J512 USB host
arm64: tegra: Add XUSB pad controller's "nvidia,pmc" property on Tegra210
arm64: tegra: Add power-domain for Tegra210 HDA
dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM
Link: https://lore.kernel.org/r/20210129193254.3610492-5-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: tegra: Device tree changes for v5.12-rc1
Fixes the pinmux configuration for the eMMC on the Ouya to fix issues
with certain bootloaders.
* tag 'tegra-for-5.12-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: ouya: Fix eMMC on specific bootloaders
Link: https://lore.kernel.org/r/20210129193254.3610492-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable support for audio-graph based sound card on Jetson AGX Xavier.
Following I/O interfaces are enabled.
* I2S1, I2S2, I2S4 and I2S6
* DMIC3
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable support for audio-graph based sound card on Jetson TX2. Based
on the board design following I/O modules are enabled.
* All I2S instances (I2S1 ... I2S6)
* All DSPK instances (DSPK1, DSPK2)
* DMIC1, DMIC2 and DMIC3
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ouya fails to detect the eMMC module when booted via certain bootloaders.
Fastboot and hard-kexec bootloaders fail while u-boot does not. It was
discovered that the issue manifests if the sdmmc4 alternate configuration
clock pin is input disabled.
Ouya uses sdmmc4 in the primary pin configuration. It is unknown why this
occurs, though it is likely related to other eMMC limitations experienced
on Ouya.
For now, fix it by enabling input on cam_mclk_pcc0.
Fixes: d7195ac5c9 ("ARM: tegra: Add device-tree for Ouya")
Reported-by: Matt Merhar <mattmerhar@protonmail.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Two different SKUs exist for the Jetson Xavier NX module, so document
the compatible strings for both, as well as the developer kits that come
with each of the SKUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Devicetree changes for omaps for v5.12 merge window
This includes the following earlier patches that were considered too
late for v5.11 as discussed between Arnd and me on freenode #armlinux
in December:
- More updates to use cpsw switchdev driver
- Enable gta04 PMIC power management
- Updates for dra7 for ECC support, 1.8GHz speed and keep the
ldo0 regulator always on as specified in the data manual
And then we have the new devicetree changes:
- Configure the original Amazon Echo to for audio
- Configure missing thermal interrupt for omap4430
- Configure mapphone devices for passive thermal cooling, and add
1.2GHz mode.
- Correct omap4430 sgx clock rate to use the runtime Android kernel
value, the earlier value was for a lower power operating point
- Drop turbo mode for 1GHz omap3 variants as we now have passive
cooling configured
- Update email address for Javier
- Add new MYIR Tech Limited board support
* tag 'omap-for-v5.12/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-myirtech-*: Add DT for AM335X MYIR Tech Limited board
ARM: dts: omap3-igep: Change email address in copyright notice
ARM: dts: omap36xx: Remove turbo mode for 1GHz variants
ARM: dts: omap443x: Correct sgx clock to 307.2MHz as used on motorola vendor kernel
ARM: dts: motorola-mapphone: Add 1.2GHz OPP
ARM: dts: motorola-mapphone: Configure lower temperature passive cooling
ARM: dts: Configure missing thermal interrupt for 4430
ARM: dts: omap3-echo: Add speaker sound card support
ARM: dts: dra71-evm: mark ldo0 regulator as always on
ARM: dts: dra76x: add support for OPP_PLUS
ARM: dts: am574x-idk: add support for EMIF1 ECC
ARM: dts: omap3-gta04: fix twl4030-power settings
ARM: dts: am335x-evm/evmsk/icev2: switch to new cpsw switch drv
ARM: dts: am33xx-l4: add dt node for new cpsw switchdev driver
Link: https://lore.kernel.org/r/pull-1611845066-809577@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM64: DT: Hisilicon ARM64 DT updates for 5.12
- Further cleanups of the hisilicon DTS to align with the dtschema
- Add or update the I2C, pinctrl and reset nodes for Hikey970
* tag 'hisi-arm64-dt-for-5.12v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: hi3670.dtsi: add I2C settings
arm64: dts: hisilicon: hikey970-pinctrl.dtsi: add missing pinctrl settings
arm64: dts: hisilicon: hi3670.dtsi: add iomcu_rst
arm64: dts: hisilicon: delete unused property smmu-cb-memtype
arm64: dts: hisilicon: avoid irrelevant nodes being mistakenly identified as PHY nodes
arm64: dts: hisilicon: normalize the node name of the localbus
arm64: dts: hisilicon: normalize the node name of the module thermal
arm64: dts: hisilicon: place clock-names "bus" before "core"
arm64: dts: hisilicon: separate each group of data in the property "ranges"
Link: https://lore.kernel.org/r/6013D1C7.90902@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The I2C buses are not declared at the device tree. As this will
be needed by further patches, add them, keeping all in
disabled state. Per-board settings can override it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
There are several pinctrl settings that are missing at this
DT file.
Also, the entries are out of order.
Add the missing bits, as they'll be required by the DRM driver - and
probably by other drivers not upstreamed yet.
Reorder the entres, adding the missing bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The "smmu-cb-memtype" is a private property developed by the Hisilicon
driver in the early stage and is not used now. So delete it.
Otherwise, below YAML check warnings are reported:
arch/arm64/boot/dts/hisilicon/hip06-d03.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/hisilicon/hip07-d05.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Currently, the names of several nodes incorrectly match common PHY
provider schema. And the phy-provider.yaml requires them must have
property "#phy-cells". As a result, false positives similar to the
following are reported:
usb2-phy@120: '#phy-cells' is a required property
Change their names slightly so that they do not match pattern:
"^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Change the node name of the localbus to match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'. This error
is detected by simple-bus.yaml.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
1. Change the node name of the thermal zone to match
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', add suffix "-thermal".
2. Change the node name of the trip point to match
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', delete character "@".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Look at the clock-names schema defined in arm,mali-utgard.yaml:
clock-names:
items:
- const: bus
- const: core
The "bus" needs to be placed before the "core".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Do not write the "ranges" of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported:
soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not valid under \
any of the given schemas (Possible causes of the failure):
soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not of type 'boolean'
soc: pcie@a0090000:ranges:0: [33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
usbphyc is a 48Mhz clock provider: the clock can be used as clock source
for USB OTG. Add #clock-cells property to usbphyc node to reflect this
capability.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add SDA/SCL pinmux lines for I2C6 on STM32MP1.
This support adds both in default and sleep states.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
"make dtbs_check" fails with:
arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dt.yaml: eeprom@50: compatible: 'oneOf' conditional failed, one must be fixed:
'microchip,at24c64' does not match '^(atmel|catalyst|microchip|nxp|ramtron|renesas|rohm|st),(24(c|cs|lc|mac)[0-9]+|spd)$'
Fix this by dropping the bogus "at" prefix.
Fixes: a1d8a344f1 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210128110136.2293490-1-geert+renesas@glider.be
Add support for the variant of the Jetson Xavier NX Developer Kit that
has a system-on-module which includes an eMMC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two versions of the Jetson Xavier NX system-on-module; one
with a micro SD-card slot and one with an eMMC. Currently, only the
system-on-module with the micro SD-card slot is supported. Before adding
support for the eMMC variant, move the common device-tree parts of the
existing Jetson Xavier NX system-on-module board (p3668-0000) and
reference carrier board (p3509-0000) into include files that can be used
by both Jetson Xavier NX variants.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
