[ Upstream commit c47527cbcc ]
The stm32_usart_transmit_chars() may be called with empty or stopped
transmit queue, and no XON/OFF character pending. This can happen at
the end of transmission, where this last call is used to either handle
the XON/XOFF x_char, or disable TX interrupt if queue is empty or
stopped.
If that occurs, do not assert the RS485 RTS/DE GPIO anymore, as the
GPIO would remain asserted past the end of transmission and that would
block the RS485 bus after the transmission.
Only assert the RS485 RTS/DE GPIO if there is either pending XON/XOFF
x_char, or at least one character in running transmit queue.
Fixes: d7c7671616 ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230223042252.95480-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4decf4060e ]
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
Fixes: 72704f876f ("dwc3: gadget: Implement the suspend entry event handler")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5239a89b06 ]
This reverts commit 76d62f24db.
So while priority inversion on the pmsg_lock is an occasional
problem that an rt_mutex would help with, in uses where logging
is writing to pmsg heavily from multiple threads, the pmsg_lock
can be heavily contended.
After this change landed, it was reported that cases where the
mutex locking overhead was commonly adding on the order of 10s
of usecs delay had suddenly jumped to ~msec delay with rtmutex.
It seems the slight differences in the locks under this level
of contention causes the normal mutexes to utilize the spinning
optimizations, while the rtmutexes end up in the sleeping
slowpath (which allows additional threads to pile on trying
to take the lock).
In this case, it devolves to a worse case senerio where the lock
acquisition and scheduling overhead dominates, and each thread
is waiting on the order of ~ms to do ~us of work.
Obviously, having tons of threads all contending on a single
lock for logging is non-optimal, so the proper fix is probably
reworking pstore pmsg to have per-cpu buffers so we don't have
contention.
Additionally, Steven Rostedt has provided some furhter
optimizations for rtmutexes that improves the rtmutex spinning
path, but at least in my testing, I still see the test tripping
into the sleeping path on rtmutexes while utilizing the spinning
path with mutexes.
But in the short term, lets revert the change to the rt_mutex
and go back to normal mutexes to avoid a potentially major
performance regression. And we can work on optimizations to both
rtmutexes and finer-grained locking for pstore pmsg in the
future.
Cc: Wei Wang <wvw@google.com>
Cc: Midas Chien<midaschieh@google.com>
Cc: "Chunhui Li (李春辉)" <chunhui.li@mediatek.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: "Guilherme G. Piccoli" <gpiccoli@igalia.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: kernel-team@android.com
Fixes: 76d62f24db ("pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion")
Reported-by: "Chunhui Li (李春辉)" <chunhui.li@mediatek.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230308204043.2061631-1-jstultz@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f46703609 ]
Commit cc7ad0d77b ("drivers: staging: rtl8723bs: Fix deadlock in
rtw_surveydone_event_callback()") besides fixing the deadlock also
modified rtw_scan_timeout_handler() to use spin_[un]lock_irq()
instead of spin_[un]lock_bh().
Disabling the IRQs is not necessary since all code taking this lock
runs from either user contexts or from softirqs
rtw_scan_timeout_handler() is the only function taking pmlmepriv->lock
which uses spin_[un]lock_irq() for this. Switch back to
spin_[un]lock_bh() to make it consistent with the rest of the code.
Fixes: cc7ad0d77b ("drivers: staging: rtl8723bs: Fix deadlock in rtw_surveydone_event_callback()")
Cc: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230221145326.7808-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 215792eda0 ]
Commit 041879b12d ("drivers: staging: rtl8192bs: Fix deadlock in
rtw_joinbss_event_prehandle()") besides fixing the deadlock also
modified _rtw_join_timeout_handler() to use spin_[un]lock_irq()
instead of spin_[un]lock_bh().
_rtw_join_timeout_handler() calls rtw_do_join() which takes
pmlmepriv->scanned_queue.lock using spin_[un]lock_bh(). This
spin_unlock_bh() call re-enables softirqs which triggers an oops in
kernel/softirq.c: __local_bh_enable_ip() when it calls
lockdep_assert_irqs_enabled():
[ 244.506087] WARNING: CPU: 2 PID: 0 at kernel/softirq.c:376 __local_bh_enable_ip+0xa6/0x100
...
[ 244.509022] Call Trace:
[ 244.509048] <IRQ>
[ 244.509100] _rtw_join_timeout_handler+0x134/0x170 [r8723bs]
[ 244.509468] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs]
[ 244.509772] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs]
[ 244.510076] call_timer_fn+0x95/0x2a0
[ 244.510200] __run_timers.part.0+0x1da/0x2d0
This oops is causd by the switch to spin_[un]lock_irq() which disables
the IRQs for the entire duration of _rtw_join_timeout_handler().
Disabling the IRQs is not necessary since all code taking this lock
runs from either user contexts or from softirqs, switch back to
spin_[un]lock_bh() to fix this.
Fixes: 041879b12d ("drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()")
Cc: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230221145326.7808-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50749f2dd6 ]
syzkaller reported [0] memory leaks of an UDP socket and ZEROCOPY
skbs. We can reproduce the problem with these sequences:
sk = socket(AF_INET, SOCK_DGRAM, 0)
sk.setsockopt(SOL_SOCKET, SO_TIMESTAMPING, SOF_TIMESTAMPING_TX_SOFTWARE)
sk.setsockopt(SOL_SOCKET, SO_ZEROCOPY, 1)
sk.sendto(b'', MSG_ZEROCOPY, ('127.0.0.1', 53))
sk.close()
sendmsg() calls msg_zerocopy_alloc(), which allocates a skb, sets
skb->cb->ubuf.refcnt to 1, and calls sock_hold(). Here, struct
ubuf_info_msgzc indirectly holds a refcnt of the socket. When the
skb is sent, __skb_tstamp_tx() clones it and puts the clone into
the socket's error queue with the TX timestamp.
When the original skb is received locally, skb_copy_ubufs() calls
skb_unclone(), and pskb_expand_head() increments skb->cb->ubuf.refcnt.
This additional count is decremented while freeing the skb, but struct
ubuf_info_msgzc still has a refcnt, so __msg_zerocopy_callback() is
not called.
The last refcnt is not released unless we retrieve the TX timestamped
skb by recvmsg(). Since we clear the error queue in inet_sock_destruct()
after the socket's refcnt reaches 0, there is a circular dependency.
If we close() the socket holding such skbs, we never call sock_put()
and leak the count, sk, and skb.
TCP has the same problem, and commit e0c8bccd40 ("net: stream:
purge sk_error_queue in sk_stream_kill_queues()") tried to fix it
by calling skb_queue_purge() during close(). However, there is a
small chance that skb queued in a qdisc or device could be put
into the error queue after the skb_queue_purge() call.
In __skb_tstamp_tx(), the cloned skb should not have a reference
to the ubuf to remove the circular dependency, but skb_clone() does
not call skb_copy_ubufs() for zerocopy skb. So, we need to call
skb_orphan_frags_rx() for the cloned skb to call skb_copy_ubufs().
[0]:
BUG: memory leak
unreferenced object 0xffff88800c6d2d00 (size 1152):
comm "syz-executor392", pid 264, jiffies 4294785440 (age 13.044s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 cd af e8 81 00 00 00 00 ................
02 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............
backtrace:
[<0000000055636812>] sk_prot_alloc+0x64/0x2a0 net/core/sock.c:2024
[<0000000054d77b7a>] sk_alloc+0x3b/0x800 net/core/sock.c:2083
[<0000000066f3c7e0>] inet_create net/ipv4/af_inet.c:319 [inline]
[<0000000066f3c7e0>] inet_create+0x31e/0xe40 net/ipv4/af_inet.c:245
[<000000009b83af97>] __sock_create+0x2ab/0x550 net/socket.c:1515
[<00000000b9b11231>] sock_create net/socket.c:1566 [inline]
[<00000000b9b11231>] __sys_socket_create net/socket.c:1603 [inline]
[<00000000b9b11231>] __sys_socket_create net/socket.c:1588 [inline]
[<00000000b9b11231>] __sys_socket+0x138/0x250 net/socket.c:1636
[<000000004fb45142>] __do_sys_socket net/socket.c:1649 [inline]
[<000000004fb45142>] __se_sys_socket net/socket.c:1647 [inline]
[<000000004fb45142>] __x64_sys_socket+0x73/0xb0 net/socket.c:1647
[<0000000066999e0e>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<0000000066999e0e>] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80
[<0000000017f238c1>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
BUG: memory leak
unreferenced object 0xffff888017633a00 (size 240):
comm "syz-executor392", pid 264, jiffies 4294785440 (age 13.044s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 2d 6d 0c 80 88 ff ff .........-m.....
backtrace:
[<000000002b1c4368>] __alloc_skb+0x229/0x320 net/core/skbuff.c:497
[<00000000143579a6>] alloc_skb include/linux/skbuff.h:1265 [inline]
[<00000000143579a6>] sock_omalloc+0xaa/0x190 net/core/sock.c:2596
[<00000000be626478>] msg_zerocopy_alloc net/core/skbuff.c:1294 [inline]
[<00000000be626478>] msg_zerocopy_realloc+0x1ce/0x7f0 net/core/skbuff.c:1370
[<00000000cbfc9870>] __ip_append_data+0x2adf/0x3b30 net/ipv4/ip_output.c:1037
[<0000000089869146>] ip_make_skb+0x26c/0x2e0 net/ipv4/ip_output.c:1652
[<00000000098015c2>] udp_sendmsg+0x1bac/0x2390 net/ipv4/udp.c:1253
[<0000000045e0e95e>] inet_sendmsg+0x10a/0x150 net/ipv4/af_inet.c:819
[<000000008d31bfde>] sock_sendmsg_nosec net/socket.c:714 [inline]
[<000000008d31bfde>] sock_sendmsg+0x141/0x190 net/socket.c:734
[<0000000021e21aa4>] __sys_sendto+0x243/0x360 net/socket.c:2117
[<00000000ac0af00c>] __do_sys_sendto net/socket.c:2129 [inline]
[<00000000ac0af00c>] __se_sys_sendto net/socket.c:2125 [inline]
[<00000000ac0af00c>] __x64_sys_sendto+0xe1/0x1c0 net/socket.c:2125
[<0000000066999e0e>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<0000000066999e0e>] do_syscall_64+0x38/0x90 arch/x86/entry/common.c:80
[<0000000017f238c1>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Fixes: b5947e5d1e ("udp: msg_zerocopy")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d325c34d9e ]
After failing to verify configuration, it returns directly without
releasing link, which may cause memory leak.
Paolo Abeni thinks that the whole code of this driver is quite
"suboptimal" and looks unmainatained since at least ~15y, so he
suggests that we could simply remove the whole driver, please
take it into consideration.
Simon Horman suggests that the fix label should be set to
"Linux-2.6.12-rc2" considering that the problem has existed
since the driver was introduced and the commit above doesn't
seem to exist in net/net-next.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Gan Gecen <gangecen@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d913d32cc2 ]
Brad Spencer provided a detailed report [0] that when calling getsockopt()
for AF_NETLINK, some SOL_NETLINK options set only 1 byte even though such
options require at least sizeof(int) as length.
The options return a flag value that fits into 1 byte, but such behaviour
confuses users who do not initialise the variable before calling
getsockopt() and do not strictly check the returned value as char.
Currently, netlink_getsockopt() uses put_user() to copy data to optlen and
optval, but put_user() casts the data based on the pointer, char *optval.
As a result, only 1 byte is set to optval.
To avoid this behaviour, we need to use copy_to_user() or cast optval for
put_user().
Note that this changes the behaviour on big-endian systems, but we document
that the size of optval is int in the man page.
$ man 7 netlink
...
Socket options
To set or get a netlink socket option, call getsockopt(2) to read
or setsockopt(2) to write the option with the option level argument
set to SOL_NETLINK. Unless otherwise noted, optval is a pointer to
an int.
Fixes: 9a4595bc7e ("[NETLINK]: Add set/getsockopt options to support more than 32 groups")
Fixes: be0c22a46c ("netlink: add NETLINK_BROADCAST_ERROR socket option")
Fixes: 38938bfe34 ("netlink: add NETLINK_NO_ENOBUFS socket flag")
Fixes: 0a6a3a23ea ("netlink: add NETLINK_CAP_ACK socket option")
Fixes: 2d4bc93368 ("netlink: extended ACK reporting")
Fixes: 89d35528d1 ("netlink: Add new socket option to enable strict checking on dumps")
Reported-by: Brad Spencer <bspencer@blackberry.com>
Link: https://lore.kernel.org/netdev/ZD7VkNWFfp22kTDt@datsun.rim.net/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/20230421185255.94606-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db2bf510bd ]
This reverts commit 1e9ac114c4.
This patch introduces a possible null-ptr-def problem. Revert it. And the
fixed bug by this patch have resolved by commit 73f7b171b7 ("Bluetooth:
btsdio: fix use after free bug in btsdio_remove due to race condition").
Fixes: 1e9ac114c4 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99e5acae19 ]
Like commit ea30388bae ("ipv6: Fix an uninit variable access bug in
__ip6_make_skb()"). icmphdr does not in skb linear region under the
scenario of SOCK_RAW socket. Access icmp_hdr(skb)->type directly will
trigger the uninit variable access bug.
Use a local variable icmp_type to carry the correct value in different
scenarios.
Fixes: 96793b4825 ("[IPV4]: Add ICMPMsgStats MIB (RFC 4293)")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7041101ff6 ]
if sch_fq is configured with "initial quantum" having values greater than
INT_MAX, the first assignment of "credit" does signed integer overflow to
a very negative value.
In this situation, the syzkaller script provided by Cristoph triggers the
CPU soft-lockup warning even with few sockets. It's not an infinite loop,
but "credit" wasn't probably meant to be minus 2Gb for each new flow.
Capping "initial quantum" to INT_MAX proved to fix the issue.
v2: validation of "initial quantum" is done in fq_policy, instead of open
coding in fq_change() _ suggested by Jakub Kicinski
Reported-by: Christoph Paasch <cpaasch@apple.com>
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/377
Fixes: afe4fd0624 ("pkt_sched: fq: Fair Queue packet scheduler")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/7b3a3c7e36d03068707a021760a194a8eb5ad41a.1682002300.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a32e98506 ]
The ->cleanup callback needs to be removed, this doesn't work anymore as
the transaction mutex is already released in the ->abort function.
Just do it after a successful validation pass, this either happens
from commit or abort phases where transaction mutex is held.
Fixes: f102d66b33 ("netfilter: nf_tables: use dedicated mutex to guard transactions")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acf1c3d68e ]
Florian and Eduard reported hard dead lock:
[ 58.433327] _raw_spin_lock_irqsave+0x40/0x50
[ 58.433334] btf_put+0x43/0x90
[ 58.433338] bpf_find_btf_id+0x157/0x240
[ 58.433353] btf_parse_fields+0x921/0x11c0
This happens since btf->refcount can be 1 at the time of btf_put() and
btf_put() will call btf_free_id() which will try to grab btf_idr_lock
and will dead lock.
Avoid the issue by doing btf_put() without locking.
Fixes: 3d78417b60 ("bpf: Add bpf_btf_find_by_name_kind() helper.")
Fixes: 1e89106da2 ("bpf: Add bpf_core_add_cands() and wire it into bpf_core_apply_relo_insn().")
Reported-by: Florian Westphal <fw@strlen.de>
Reported-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20230421014901.70908-1-alexei.starovoitov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35226750f7 ]
The system hang because of dsa_tag_8021q_port_setup()->
stmmac_vlan_rx_add_vid().
I found in stmmac_drv_probe() that cailing pm_runtime_put()
disabled the clock.
First, when the kernel is compiled with CONFIG_PM=y,The stmmac's
resume/suspend is active.
Secondly,stmmac as DSA master,the dsa_tag_8021q_port_setup() function
will callback stmmac_vlan_rx_add_vid when DSA dirver starts. However,
The system is hanged for the stmmac_vlan_rx_add_vid() accesses its
registers after stmmac's clock is closed.
I would suggest adding the pm_runtime_resume_and_get() to the
stmmac_vlan_rx_add_vid().This guarantees that resuming clock output
while in use.
Fixes: b3dcb31277 ("net: stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Yan Wang <rk.code@outlook.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b540decd0 ]
On failing to create promisc flow steering table, the pointer is
returned with an error. Nullify it so unloading the driver won't try to
destroy a non existing table.
Failing to create promisc table may happen over BF devices when the ARM
side is going through a firmware tear down. The host side start a
reload flow. While the driver unloads, it tries to remove the promisc
table. Remove WARN in this state as it is a valid error flow.
Fixes: 1c46d7409f ("net/mlx5e: Optimize promiscuous mode")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfad99750c ]
Use the same timeout for sync reset flow and health recovery flow, since
the former involves driver's recovery from firmware reset, which is
similar to health recovery. Otherwise, in some cases, such as a firmware
upgrade on the DPU, the firmware pre-init bit may not be ready within
current timeout and the driver will abort loading back after reset.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Fixes: 37ca95e62e ("net/mlx5: Increase FW pre-init timeout for health recovery")
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21608a2cf3 ]
This reverts commit 5977ac3910.
Revert this patch as we need the "recovery" arg back in mlx5_load_one()
function. This arg will be used in the next patch for using recovery
timeout during sync reset flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: dfad99750c ("net/mlx5: Use recovery timeout on sync reset flow")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72ed5d5624 ]
The original behavior introduced by commit c6acd629ee ("net/mlx5e: Add
support for devlink-port in non-representors mode") correctly
re-instantiated uplink devlink port and related netdevice during devlink
reload. However with migration to auxiliary devices, this behaviour
changed.
Restore the original behaviour and tear down auxiliary devices
completely during devlink reload.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: dfad99750c ("net/mlx5: Use recovery timeout on sync reset flow")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a6b069cc6 ]
On representor init rx error flow the flow steering pointer is being
released so mlx5e_attach_netdev() doesn't have a valid fs pointer
in its error flow. Make sure the pointer is nullified when released
and add a check in mlx5e_fs_cleanup() to verify fs is not null
as representor cleanup callback would be called anyway.
Fixes: af8bbf7300 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c81893025 ]
Source port rewrite (forward to ovs internal port or statck device) isn't
supported in the rule of split action. So there is no indirect table in
split rule. The cited commit destroyes indirect table in split rule. The
indirect table for other rules will be destroyed wrongly. It will cause
traffic loss.
Fix it by removing the destroy function in split rule. And also remove
the destroy function in error flow.
Fixes: 10742efc20 ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd745f4c0a ]
Currently when creating per vport table, create flags are hardcoded.
Devlink encap mode is set based on user input and HW capability.
Create per vport table based on devlink encap mode.
Fixes: c796bb7cd2 ("net/mlx5: E-switch, Generalize per vport table API")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e85d3d5587 ]
ethtool uses `ETHTOOL_GRXRINGS` to compute how many queues are supported
by RSS. The driver should return the smaller of either:
- The maximum number of RSS queues the device supports, OR
- The number of RX queues configured
Prior to this change, running `ethtool -X $iface default` fails if the
number of queues configured is larger than the number supported by RSS,
even though changing the queue count correctly resets the flowhash to
use all supported queues.
Other drivers (for example, i40e) will succeed but the flow hash will
reset to support the maximum number of queues supported by RSS, even if
that amount is smaller than the configured amount.
Prior to this change:
$ sudo ethtool -L eth1 combined 20
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 20 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
24: 8 9 10 11 12 13 14 15
32: 0 1 2 3 4 5 6 7
...
You can see that the flowhash was correctly set to use the maximum
number of queues supported by the driver (16).
However, asking the NIC to reset to "default" fails:
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this change, the flowhash can be reset to default which will use
all of the available RSS queues (16) or the configured queue count,
whichever is smaller.
Starting with eth1 which has 10 queues and a flowhash distributing to
all 10 queues:
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
...
Increasing the queue count to 48 resets the flowhash to distribute to 16
queues, as it did before this patch:
$ sudo ethtool -L eth1 combined 48
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Due to the other bugfix in this series, the flowhash can be set to use
queues 0-5:
$ sudo ethtool -X eth1 equal 5
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 0 1 2
8: 3 4 0 1 2 3 4 0
16: 1 2 3 4 0 1 2 3
...
Due to this bugfix, the flowhash can be reset to default and use 16
queues:
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Fixes: 91cd94bfe4 ("ixgbe: add basic support for setting and getting nfc controls")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f3ed1293f ]
ixgbe currently returns `EINVAL` whenever the flowhash it set by ethtool
because the ethtool code in the kernel passes a non-zero value for hfunc
that ixgbe should allow.
When ethtool is called with `ETHTOOL_SRXFHINDIR`,
`ethtool_set_rxfh_indir` will call ixgbe's set_rxfh function
with `ETH_RSS_HASH_NO_CHANGE`. This value should be accepted.
When ethtool is called with `ETHTOOL_SRSSH`, `ethtool_set_rxfh` will
call ixgbe's set_rxfh function with `rxfh.hfunc`, which appears to be
hardcoded in ixgbe to always be `ETH_RSS_HASH_TOP`. This value should
also be accepted.
Before this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
24: 4 5 6 7 8 9 0 1
...
Fixes: 1c7cf0784e ("ixgbe: support for ethtool set_rxfh")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73db1b8f2b ]
(struct nf_conn)->timeout is an interval before the conntrack
confirmed. After confirmed, it becomes a timestamp.
It is observed that timeout of an unconfirmed conntrack:
- Set by calling ctnetlink_change_timeout(). As a result,
`nfct_time_stamp` was wrongly added to `ct->timeout` twice.
- Get by calling ctnetlink_dump_timeout(). As a result,
`nfct_time_stamp` was wrongly subtracted.
Call Trace:
<TASK>
dump_stack_lvl
ctnetlink_dump_timeout
__ctnetlink_glue_build
ctnetlink_glue_build
__nfqnl_enqueue_packet
nf_queue
nf_hook_slow
ip_mc_output
? __pfx_ip_finish_output
ip_send_skb
? __pfx_dst_output
udp_send_skb
udp_sendmsg
? __pfx_ip_generic_getfrag
sock_sendmsg
Separate the 2 cases in:
- Setting `ct->timeout` in __nf_ct_set_timeout().
- Getting `ct->timeout` in ctnetlink_dump_timeout().
Pablo appends:
Update ctnetlink to set up the timeout _after_ the IPS_CONFIRMED flag is
set on, otherwise conntrack creation via ctnetlink breaks.
Note that the problem described in this patch occurs since the
introduction of the nfnetlink_queue conntrack support, select a
sufficiently old Fixes: tag for -stable kernel to pick up this fix.
Fixes: a4b4766c3c ("netfilter: nfnetlink_queue: rename related to nfqueue attaching conntrack info")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d2892e050 ]
The vif->bss_conf.mcast_rate should be applied to multicast data frame
only.
Fixes: 182071cdd5 ("mt76: connac: move connac2_mac_write_txwi in mt76_connac module")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d78c46423 ]
If the chip reset worker is triggered during the remove process, the chip
DMA may not be properly pushed back to the idle state. This can lead to
corruption of the DMA flow due to the chip reset. Therefore, it is
necessary to stop the chip reset before the DMA is finalized.
To avoid resetting the chip after the reset worker is cancelled, use
__mt7921_mcu_drv_pmctrl() instead of mt7921_mcu_drv_pmctrl(). It is safe to
ignore the pm mutex because the pm worker and wake worker have already been
cancelled.
Fixes: 033ae79b38 ("mt76: mt7921: refactor init.c to be bus independent")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87714bf6ed ]
The hardware team has advised the driver that it is necessary to first put
WFDMA into an idle state before resetting the WFDMA. Otherwise, the WFDMA
may enter an unknown state where it cannot be polled with the right state
successfully. To ensure that the DMA can work properly while a stressful
cold reboot test was being made, we have reordered the programming sequence
in the driver based on the hardware team's guidance.
The patch would modify the WFDMA disabling flow from
"DMA reset -> disabling DMASHDL -> disabling WFDMA -> polling and waiting
until DMA idle" to "disabling WFDMA -> polling and waiting for DMA idle ->
disabling DMASHDL -> DMA reset.
Where he polling and waiting until WFDMA is idle is coordinated with the
operation of disabling WFDMA. Even while WFDMA is being disabled, it can
still handle Tx/Rx requests. The additional polling allows sufficient time
for WFDMA to process the last T/Rx request. When the idle state of WFDMA is
reached, it is a reliable indication that DMASHDL is also idle to ensure it
is safe to disable it and perform the DMA reset.
Fixes: 0a1059d0f0 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c47cdebba ]
`mt7921u_dma_init` can only return zero or negative number according to its
definition. When it returns non-zero number, there exists an error and this
function should handle this error rather than return directly.
Fixes: 0d2afe09fa ("mt76: mt7921: add mt7921u driver")
Signed-off-by: Jiefeng Li <jiefeng_li@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23792cedaf ]
mt76 scan command only support 64 channels currently. If the
channel count is larger than 64(for 2+5+6GHz), some channels will
not be scanned. Hence change the scan type to full channel scan
in case of the command cannot include proper list for chip.
Fixes: 399090ef96 ("mt76: mt76_connac: move hw_scan and sched_scan routine in mt76_connac_mcu module")
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Isaac Konikoff <konikofi@candelatech.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c397fc1e63 ]
In system warm reboot scene, due to the polling timeout(now 1000us)
is too short to wait dma idle in time, it may make driver probe fail
with error code -ETIMEDOUT. Meanwhile, we also found the dma may take
around 70ms to enter idle state. Change the polling idle timeout to
100ms to avoid the probabilistic probe fail.
Tested pass with 5000 times warm reboot on x86 platform.
[4.477496] pci 0000:01:00.0: attach allowed to drvr mt7921e [internal device]
[4.478306] mt7921e 0000:01:00.0: ASIC revision: 79610010
[4.480063] mt7921e: probe of 0000:01:00.0 failed with error -110
Fixes: 0a1059d0f0 ("mt76: mt7921: move mt7921_dma_reset in dma.c")
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35effe6c0c ]
The default waiting unit is 10ms and the value is too much for
data path related control. Provide a new API mt76_poll_msec_tick()
to support different cases, such as 1ms polling waiting kick.
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stable-dep-of: c397fc1e63 ("wifi: mt76: mt7921e: fix probe timeout after reboot")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90fb69212c ]
On MT7986 the WiFi driver currently does not get automatically loaded,
requiring manual modprobing because the device tree compatibles are not
exported into metadata.
Add the missing MODULE_DEVICE_TABLE macro to fix this.
Fixes: 99ad32a4ca ("mt76: mt7915: add support for MT7986")
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd159398a2 ]
When invalidating buffers under the partial tail page,
jbd2_journal_invalidate_folio() returns -EBUSY if the buffer is part of
the committing transaction as we cannot safely modify buffer state.
However if the buffer is already invalidated (due to previous
invalidation attempts from ext4_wait_for_tail_page_commit()), there's
nothing to do and there's no point in returning -EBUSY. This fixes
occasional warnings from ext4_journalled_invalidate_folio() triggered by
generic/051 fstest when blocksize < pagesize.
Fixes: 53e872681f ("ext4: fix deadlock in journal_unmap_buffer()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230329154950.19720-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
