[ Upstream commit ef9da46dde ]
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02a1b175b0 ]
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ed42989eab ]
skb_unshare() drops a reference count on the old skb unconditionally,
so in the failure case, we end up freeing the skb twice here.
And because the skb is allocated in fclone and cloned by caller
tipc_msg_reassemble(), the consequence is actually freeing the
original skb too, thus triggered the UAF by syzbot.
Fix this by replacing this skb_unshare() with skb_cloned()+skb_copy().
Fixes: ff48b6222e ("tipc: use skb_unshare() instead in tipc_buf_append()")
Reported-and-tested-by: syzbot+e96a7ba46281824cc46a@syzkaller.appspotmail.com
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 413f142cc0 ]
Ingress large send packets are identified by either:
The IBMVETH_RXQ_LRG_PKT flag in the receive buffer
or with a -1 placed in the ip header checksum.
The method used depends on firmware version. Frame
geometry and sufficient header validation is performed by the
hypervisor eliminating the need for further header checks here.
Fixes: 7b5967389f ("ibmveth: set correct gso_size and gso_type")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Reviewed-by: Cristobal Forno <cris.forno@ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45cb6653b0 upstream.
Return -EINVAL for authenc(hmac(sha1),cbc(aes)),
authenc(hmac(sha256),cbc(aes)) and authenc(hmac(sha512),cbc(aes))
if the cipher length is not multiple of the AES block.
This is to prevent an undefined device behaviour.
Fixes: d370cec321 ("crypto: qat - Intel(R) QAT crypto interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dominik Przychodni <dominik.przychodni@intel.com>
[giovanni.cabiddu@intel.com: reworded commit message]
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2bb80b8bd upstream.
With suitably crafted reiserfs image and mount command reiserfs will
crash when trying to verify that XATTR_ROOT directory can be looked up
in / as that recurses back to xattr code like:
xattr_lookup+0x24/0x280 fs/reiserfs/xattr.c:395
reiserfs_xattr_get+0x89/0x540 fs/reiserfs/xattr.c:677
reiserfs_get_acl+0x63/0x690 fs/reiserfs/xattr_acl.c:209
get_acl+0x152/0x2e0 fs/posix_acl.c:141
check_acl fs/namei.c:277 [inline]
acl_permission_check fs/namei.c:309 [inline]
generic_permission+0x2ba/0x550 fs/namei.c:353
do_inode_permission fs/namei.c:398 [inline]
inode_permission+0x234/0x4a0 fs/namei.c:463
lookup_one_len+0xa6/0x200 fs/namei.c:2557
reiserfs_lookup_privroot+0x85/0x1e0 fs/reiserfs/xattr.c:972
reiserfs_fill_super+0x2b51/0x3240 fs/reiserfs/super.c:2176
mount_bdev+0x24f/0x360 fs/super.c:1417
Fix the problem by bailing from reiserfs_xattr_get() when xattrs are not
yet initialized.
CC: stable@vger.kernel.org
Reported-by: syzbot+9b33c9b118d77ff59b6f@syzkaller.appspotmail.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cf87e5edd upstream.
There exist many FT2232-based JTAG+UART adapter designs in which
FT2232 Channel A is used for JTAG and Channel B is used for UART.
The best way to handle them in Linux is to have the ftdi_sio driver
create a ttyUSB device only for Channel B and not for Channel A:
a ttyUSB device for Channel A would be bogus and will disappear as
soon as the user runs OpenOCD or other applications that access
Channel A for JTAG from userspace, causing undesirable noise for
users. The ftdi_sio driver already has a dedicated quirk for such
JTAG+UART FT2232 adapters, and it requires assigning custom USB IDs
to such adapters and adding these IDs to the driver with the
ftdi_jtag_quirk applied.
Boutique hardware manufacturer Falconia Partners LLC has created a
couple of JTAG+UART adapter designs (one buffered, one unbuffered)
as part of FreeCalypso project, and this hardware is specifically made
to be used with Linux hosts, with the intent that Channel A will be
accessed only from userspace via appropriate applications, and that
Channel B will be supported by the ftdi_sio kernel driver, presenting
a standard ttyUSB device to userspace. Toward this end the hardware
manufacturer will be programming FT2232 EEPROMs with custom USB IDs,
specifically with the intent that these IDs will be recognized by
the ftdi_sio driver with the ftdi_jtag_quirk applied.
Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[johan: insert in PID order and drop unused define]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 339ddaa626 upstream.
Starting with the upgrade to v5.8-rc3, I've noticed I wasn't able to
connect to my Bluetooth headset properly anymore. While connecting to
the device would eventually succeed, bluetoothd seemed to be confused
about the current connection state where the state was flapping hence
and forth. Bisecting this issue led to commit 3ca44c16b0 (Bluetooth:
Consolidate encryption handling in hci_encrypt_cfm, 2020-05-19), which
refactored `hci_encrypt_cfm` to also handle updating the connection
state.
The commit in question changed the code to call `hci_connect_cfm` inside
`hci_encrypt_cfm` and to change the connection state. But with the
conversion, we now only update the connection state if a status was set
already. In fact, the reverse should be true: the status should be
updated if no status is yet set. So let's fix the isuse by reversing the
condition.
Fixes: 3ca44c16b0 ("Bluetooth: Consolidate encryption handling in hci_encrypt_cfm")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ca44c16b0 upstream.
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Hans-Christian Noren Egtvedt <hegtvedt@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b560a208cd upstream.
This checks if BT_HS is enabled relecting it on MGMT_SETTING_HS instead
of always reporting it as supported.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19425641c upstream.
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38b1dc47a3 ]
If someone calls setsockopt() twice to set a server key keyring, the first
keyring is leaked.
Fix it to return an error instead if the server key keyring is already set.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa1d113a0f ]
conn->state_lock may be taken in softirq mode, but a previous patch
replaced an outer lock in the response-packet event handling code, and lost
the _bh from that when doing so.
Fix this by applying the _bh annotation to the state_lock locking.
Fixes: a1399f8bb0 ("rxrpc: Call channels should have separate call number spaces")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a059cd5ca ]
If rxrpc_read() (which allows KEYCTL_READ to read a key), sees a token of a
type it doesn't recognise, it can BUG in a couple of places, which is
unnecessary as it can easily get back to userspace.
Fix this to print an error message instead.
Fixes: 99455153d0 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56305118e0 ]
The session key should be encoded with just the 8 data bytes and
no length; ENCODE_DATA precedes it with a 4 byte length, which
confuses some existing tools that try to parse this format.
Add an ENCODE_BYTES macro that does not include a length, and use
it for the key. Also adjust the expected length.
Note that commit 774521f353 ("rxrpc: Fix an assertion in
rxrpc_read()") had fixed a BUG by changing the length rather than
fixing the encoding. The original length was correct.
Fixes: 99455153d0 ("RxRPC: Parse security index 5 keys (Kerberos 5)")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e94ee17134 ]
The struct flowi must never be interpreted by itself as its size
depends on the address family. Therefore it must always be grouped
with its original family value.
In this particular instance, the original family value is lost in
the function xfrm_state_find. Therefore we get a bogus read when
it's coupled with the wrong family which would occur with inter-
family xfrm states.
This patch fixes it by keeping the original family value.
Note that the same bug could potentially occur in LSM through
the xfrm_state_pol_flow_match hook. I checked the current code
there and it seems to be safe for now as only secid is used which
is part of struct flowi_common. But that API should be changed
so that so that we don't get new bugs in the future. We could
do that by replacing fl with just secid or adding a family field.
Reported-by: syzbot+577fbac3145a6eb2e7a5@syzkaller.appspotmail.com
Fixes: 48b8d78315 ("[XFRM]: State selection update to use inner...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7241c5a697 ]
EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.
Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.
Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.
Fixes: 8a7493e58a ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8366685b28 ]
When we clone state only add_time was cloned. It missed values like
bytes, packets. Now clone the all members of the structure.
v1->v3:
- use memcpy to copy the entire structure
Fixes: 80c9abaabf ("[XFRM]: Extension for dynamic update of endpoint address(es)")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91a46c6d1b ]
XFRMA_REPLAY_ESN_VAL was not cloned completely from the old to the new.
Migrate this attribute during XFRMA_MSG_MIGRATE
v1->v2:
- move curleft cloning to a separate patch
Fixes: af2f464e32 ("xfrm: Assign esn pointers when cloning a state")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8aa7b526dc upstream.
With multiple DNAT rules it's possible that after destination
translation the resulting tuples collide.
For example, two openvswitch flows:
nw_dst=10.0.0.10,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
nw_dst=10.0.0.20,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
Assuming two TCP clients initiating the following connections:
10.0.0.10:5000->10.0.0.10:10
10.0.0.10:5000->10.0.0.20:10
Both tuples would translate to 10.0.0.10:5000->20.0.0.1:20 causing
nf_conntrack_confirm() to fail because of tuple collision.
Netfilter handles this case by allocating a null binding for SNAT at
egress by default. Perform the same operation in openvswitch for DNAT
if no explicit SNAT is requested by the user and allocate a null binding
for SNAT for packets in the "original" direction.
Reported-at: https://bugzilla.redhat.com/1877128
Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: 05752523e5 ("openvswitch: Interface with NAT.")
Signed-off-by: Dumitru Ceara <dceara@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a9e774959 upstream.
The variable "i" isn't initialized back correctly after the first loop
under the label inst_rollback gets executed.
The value of "i" is assigned to be option_count - 1, and the ensuing
loop (under alloc_rollback) begins by initializing i--.
Thus, the value of i when the loop begins execution will now become
i = option_count - 2.
Thus, when kfree(dst_opts[i]) is called in the second loop in this
order, (i.e., inst_rollback followed by alloc_rollback),
dst_optsp[option_count - 2] is the first element freed, and
dst_opts[option_count - 1] does not get freed, and thus, a memory
leak is caused.
This memory leak can be fixed, by assigning i = option_count (instead of
option_count - 1).
Fixes: 80f7c6683f ("team: add support for per-port options")
Reported-by: syzbot+69b804437cfec30deac3@syzkaller.appspotmail.com
Tested-by: syzbot+69b804437cfec30deac3@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89d01748b2 upstream.
Some devices set needed_headroom. If we ignore it, we might
end up crashing in various skb_push() for example in ipgre_header()
since some layers assume enough headroom has been reserved.
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 033b5d7755 upstream.
There have been elusive reports of filemap_fault() hitting its
VM_BUG_ON_PAGE(page_to_pgoff(page) != offset, page) on kernels built
with CONFIG_READ_ONLY_THP_FOR_FS=y.
Suren has hit it on a kernel with CONFIG_READ_ONLY_THP_FOR_FS=y and
CONFIG_NUMA is not set: and he has analyzed it down to how khugepaged
without NUMA reuses the same huge page after collapse_file() failed
(whereas NUMA targets its allocation to the respective node each time).
And most of us were usually testing with CONFIG_NUMA=y kernels.
collapse_file(old start)
new_page = khugepaged_alloc_page(hpage)
__SetPageLocked(new_page)
new_page->index = start // hpage->index=old offset
new_page->mapping = mapping
xas_store(&xas, new_page)
filemap_fault
page = find_get_page(mapping, offset)
// if offset falls inside hpage then
// compound_head(page) == hpage
lock_page_maybe_drop_mmap()
__lock_page(page)
// collapse fails
xas_store(&xas, old page)
new_page->mapping = NULL
unlock_page(new_page)
collapse_file(new start)
new_page = khugepaged_alloc_page(hpage)
__SetPageLocked(new_page)
new_page->index = start // hpage->index=new offset
new_page->mapping = mapping // mapping becomes valid again
// since compound_head(page) == hpage
// page_to_pgoff(page) got changed
VM_BUG_ON_PAGE(page_to_pgoff(page) != offset)
An initial patch replaced __SetPageLocked() by lock_page(), which did
fix the race which Suren illustrates above. But testing showed that it's
not good enough: if the racing task's __lock_page() gets delayed long
after its find_get_page(), then it may follow collapse_file(new start)'s
successful final unlock_page(), and crash on the same VM_BUG_ON_PAGE.
It could be fixed by relaxing filemap_fault()'s VM_BUG_ON_PAGE to a
check and retry (as is done for mapping), with similar relaxations in
find_lock_entry() and pagecache_get_page(): but it's not obvious what
else might get caught out; and khugepaged non-NUMA appears to be unique
in exposing a page to page cache, then revoking, without going through
a full cycle of freeing before reuse.
Instead, non-NUMA khugepaged_prealloc_page() release the old page
if anyone else has a reference to it (1% of cases when I tested).
Although never reported on huge tmpfs, I believe its find_lock_entry()
has been at similar risk; but huge tmpfs does not rely on khugepaged
for its normal working nearly so much as READ_ONLY_THP_FOR_FS does.
Reported-by: Denis Lisov <dennis.lissov@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206569
Link: https://lore.kernel.org/linux-mm/?q=20200219144635.3b7417145de19b65f258c943%40linux-foundation.org
Reported-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/linux-xfs/?q=20200616013309.GB815%40lca.pw
Reported-and-analyzed-by: Suren Baghdasaryan <surenb@google.com>
Fixes: 87c460a0bd ("mm/khugepaged: collapse_shmem() without freezing new_page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org # v4.9+
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b40341fad6 upstream.
The first thing that the ftrace function callback helper functions should do
is to check for recursion. Peter Zijlstra found that when
"rcu_is_watching()" had its notrace removed, it caused perf function tracing
to crash. This is because the call of rcu_is_watching() is tested before
function recursion is checked and and if it is traced, it will cause an
infinite recursion loop.
rcu_is_watching() should still stay notrace, but to prevent this should
never had crashed in the first place. The recursion prevention must be the
first thing done in callback functions.
Link: https://lore.kernel.org/r/20200929112541.GM2628@hirez.programming.kicks-ass.net
Cc: stable@vger.kernel.org
Cc: Paul McKenney <paulmck@kernel.org>
Fixes: c68c0fa293 ("ftrace: Have ftrace_ops_get_func() handle RCU and PER_CPU flags too")
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29b4f5f188 upstream.
Since glibc 2.28 when running 'perf top --stdio', input handling no
longer works, but hitting any key always just prints the "Mapped keys"
help text.
To fix it, call clearerr() in the display_thread() loop to clear any EOF
sticky errors, as instructed in the glibc NEWS file
(https://sourceware.org/git/?p=glibc.git;a=blob;f=NEWS):
* All stdio functions now treat end-of-file as a sticky condition. If you
read from a file until EOF, and then the file is enlarged by another
process, you must call clearerr or another function with the same effect
(e.g. fseek, rewind) before you can read the additional data. This
corrects a longstanding C99 conformance bug. It is most likely to affect
programs that use stdio to read interactive input from a terminal.
(Bug #1190.)
Signed-off-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200305083714.9381-2-tommi.t.rantala@nokia.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 720ef73d1a upstream.
Evaluating ACPI _BCL could fail, then ACPI buffer size will be set to 0.
When reuse this ACPI buffer, AE_BUFFER_OVERFLOW will be triggered.
Re-initialize buffer size will make ACPI evaluate successfully.
Fixes: 46445b6b89 ("thinkpad-acpi: fix handle locate for video and query of _BCL")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f38b06db8 upstream.
clang static analysis flags this represenative problem
thinkpad_acpi.c:2523:7: warning: Branch condition evaluates
to a garbage value
if (!oldn->mute ||
^~~~~~~~~~~
In hotkey_kthread() mute is conditionally set by hotkey_read_nvram()
but unconditionally checked by hotkey_compare_and_issue_event().
So the tp_nvram_state variable s[2] needs to be initialized.
Fixes: 01e88f2598 ("ACPI: thinkpad-acpi: add CMOS NVRAM polling for hot keys (v9)")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4013c1496c upstream.
Kernel threads intentionally do CLONE_FS in order to follow any changes
that 'init' does to set up the root directory (or cwd).
It is admittedly a bit odd, but it avoids the situation where 'init'
does some extensive setup to initialize the system environment, and then
we execute a usermode helper program, and it uses the original FS setup
from boot time that may be very limited and incomplete.
[ Both Al Viro and Eric Biederman point out that 'pivot_root()' will
follow the root regardless, since it fixes up other users of root (see
chroot_fs_refs() for details), but overmounting root and doing a
chroot() would not. ]
However, Vegard Nossum noticed that the CLONE_FS not only means that we
follow the root and current working directories, it also means we share
umask with whatever init changed it to. That wasn't intentional.
Just reset umask to the original default (0022) before actually starting
the usermode helper program.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
