[ Upstream commit e61c38d85b ]
If the UART is operated in DTE mode and UCR3_DCD or UCR3_RI are 1 (which
is the reset default) and the opposite side pulls the respective line to
its active level the irq triggers after it is requested in .probe.
These irqs were already disabled in .startup but this might be too late.
Also setup of the UFCR_DCEDTE bit (currently done in .set_termios) is
done very late which is critical as it also controls direction of some
pins.
So setup UFCR_DCEDTE earlier (in .probe) and also disable the broken
irqs in DTE mode there before requesting irqs.
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d05587c9e ]
On SMP systems, we see a lot of spurious TX interrupts when a
program generates a steady stream of output to the pl011 UART.
The problem can be easily seen when one CPU generates the output
while another CPU handles the pl011 interrupts, and the rate of
output is low enough not to fill the TX FIFO. The problem seems
to be:
-- CPU a -- -- CPU b --
(take port lock)
pl011_start_tx
pl011_start_tx_pio
enable TXIM in REG_IMSC -> causes uart tx intr (pl011_int)
pl011_tx_chars pl011_int
...tx chars, all done... (wait for port lock)
pl011_stop_tx .
disable TXIM .
(release port lock) -> (take port lock)
check for TXIM, not enabled
(release port lock)
return IRQ_NONE
Enabling the TXIM in pl011_start_tx_pio() causes the interrupt
to be generated and delivered to CPU b, even though pl011_tx_chars()
is able to complete the TX and then disable the tx interrupt.
Fix this by enabling TXIM only after pl011_tx_chars, if it is needed.
pl011_tx_chars will return a boolean indicating whether the TX
interrupts have to be enabled.
Debugged-by: Vijaya Kumar <Vijaya.Kumar@cavium.com>
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7064dc7fc1 ]
I ran into a link error on ARM64 for lkdtm_rodata_do_nothing:
drivers/misc/built-in.o: In function `lkdtm_rodata_do_nothing':
:(.rodata+0x68c8): relocation truncated to fit: R_AARCH64_CALL26 against symbol `__sanitizer_cov_trace_pc' defined in .text section in kernel/built-in.o
I did not analyze this further, but my theory is that we would need a trampoline
to call __sanitizer_cov_trace_pc(), but the linker (correctly) only adds trampolines
for callers in executable sections.
Disabling KCOV for this one file avoids the build failure with no
other practical downsides I can think of.
The problem can only happen on kernels that contain both kcov and
lkdtm, so if we want to backport this, it should be in the earliest
version that has both (v4.8).
Fixes: 5c9a8750a6 ("kernel: add kcov code coverage")
Fixes: 9a49a528dc ("lkdtm: add function for testing .rodata section")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eeedc5421d ]
Corrected to get the port numbering to allow programmable replicator driver
to operate correctly.
By convention, CoreSight devices number ports, not endpoints in
the .dts files:-
port {
reg<N>
endpoint {
}
}
Existing code read endpoint number - always 0x0, rather than the correct
port number.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a1c779e6b ]
This patch forces the frambuffer size to be aligned on kernel pages.
During the board startup, the splash screed did appear;
the "ts_test" program or our application were not able to start.
The following error message was reported:
error: failed to map framebuffer device to memory.
LinuxFB: driver cannot connect
The issue was discovered, on the LPC32xx platform, during the migration
of the LCD definition from the board file to the device tree.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28d0635388 ]
The userspace exception injection API and code path are entirely
unprepared for exceptions that might cause a VM-exit from L2 to L1, so
the best course of action may be to simply disallow this for now.
1. The API provides no mechanism for userspace to specify the new DR6
bits for a #DB exception or the new CR2 value for a #PF
exception. Presumably, userspace is expected to modify these registers
directly with KVM_SET_SREGS before the next KVM_RUN ioctl. However, in
the event that L1 intercepts the exception, these registers should not
be changed. Instead, the new values should be provided in the
exit_qualification field of vmcs12 (Intel SDM vol 3, section 27.1).
2. In the case of a userspace-injected #DB, inject_pending_event()
clears DR7.GD before calling vmx_queue_exception(). However, in the
event that L1 intercepts the exception, this is too early, because
DR7.GD should not be modified by a #DB that causes a VM-exit directly
(Intel SDM vol 3, section 27.1).
3. If the injected exception is a #PF, nested_vmx_check_exception()
doesn't properly check whether or not L1 is interested in the
associated error code (using the #PF error code mask and match fields
from vmcs12). It may either return 0 when it should call
nested_vmx_vmexit() or vice versa.
4. nested_vmx_check_exception() assumes that it is dealing with a
hardware-generated exception intercept from L2, with some of the
relevant details (the VM-exit interruption-information and the exit
qualification) live in vmcs02. For userspace-injected exceptions, this
is not the case.
5. prepare_vmcs12() assumes that when its exit_intr_info argument
specifies valid information with a valid error code that it can VMREAD
the VM-exit interruption error code from vmcs02. For
userspace-injected exceptions, this is not the case.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74f169090b ]
MCG_CAP[63:9] bits are reserved on AMD. However, on an AMD guest, this
MSR returns 0x100010a. More specifically, bit 24 is set, which is simply
wrong. That bit is MCG_SER_P and is present only on Intel. Thus, clean
up the reserved bits in order not to confuse guests.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5016bdb796 ]
Normally, calling alloc_iova() using an iova_domain with insufficient
pfns remaining between start_pfn and dma_limit will fail and return a
NULL pointer. Unexpectedly, if such a "full" iova_domain contains an
iova with pfn_lo == 0, the alloc_iova() call will instead succeed and
return an iova containing invalid pfns.
This is caused by an underflow bug in __alloc_and_insert_iova_range()
that occurs after walking the "full" iova tree when the search ends
at the iova with pfn_lo == 0 and limit_pfn is then adjusted to be just
below that (-1). This (now huge) limit_pfn gives the impression that a
vast amount of space is available between it and start_pfn and thus
a new iova is allocated with the invalid pfn_hi value, 0xFFF.... .
To rememdy this, a check is introduced to ensure that adjustments to
limit_pfn will not underflow.
This issue has been observed in the wild, and is easily reproduced with
the following sample code.
struct iova_domain *iovad = kzalloc(sizeof(*iovad), GFP_KERNEL);
struct iova *rsvd_iova, *good_iova, *bad_iova;
unsigned long limit_pfn = 3;
unsigned long start_pfn = 1;
unsigned long va_size = 2;
init_iova_domain(iovad, SZ_4K, start_pfn, limit_pfn);
rsvd_iova = reserve_iova(iovad, 0, 0);
good_iova = alloc_iova(iovad, va_size, limit_pfn, true);
bad_iova = alloc_iova(iovad, va_size, limit_pfn, true);
Prior to the patch, this yielded:
*rsvd_iova == {0, 0} /* Expected */
*good_iova == {2, 3} /* Expected */
*bad_iova == {-2, -1} /* Oh no... */
After the patch, bad_iova is NULL as expected since inadequate
space remains between limit_pfn and start_pfn after allocating
good_iova.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f78227874 ]
When qedr is enabled, qed would try dividing the msi-x vectors between
L2 and RoCE, starting with L2 and providing it with sufficient vectors
for its queues.
Problem is qed would also do that for storage partitions, and as those
don't need queues it would lead qed to award those partitions with 0
msi-x vectors, causing them to believe theye're using INTa and
preventing them from operating.
Fixes: 51ff17251c ("qed: Add support for RoCE hw init")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75106523f3 ]
The commit 08024885a2 ("ses: Add power_status to SES device slot")
introduced the 'power_status' attribute to enclosure components and
the associated callbacks.
There are 2 callbacks available to get the power status of a device:
1) ses_get_power_status() for 'struct enclosure_component_callbacks'
2) get_component_power_status() for the sysfs device attribute
(these are available for kernel-space and user-space, respectively.)
However, despite both methods being available to get power status
on demand, that commit also introduced a call to get power status
in ses_enclosure_data_process().
This dramatically increased the total probe time for SCSI devices
on larger configurations, because ses_enclosure_data_process() is
called several times during the SCSI devices probe and loops over
the component devices (but that is another problem, another patch).
That results in a tremendous continuous hammering of SCSI Receive
Diagnostics commands to the enclosure-services device, which does
delay the total probe time for the SCSI devices __significantly__:
Originally, ~34 minutes on a system attached to ~170 disks:
[ 9214.490703] mpt3sas version 13.100.00.00 loaded
...
[11256.580231] scsi 17:0:177:0: qdepth(16), tagged(1), simple(0),
ordered(0), scsi_level(6), cmd_que(1)
With this patch, it decreased to ~2.5 minutes -- a 13.6x faster
[ 1002.992533] mpt3sas version 13.100.00.00 loaded
...
[ 1151.978831] scsi 11:0:177:0: qdepth(16), tagged(1), simple(0),
ordered(0), scsi_level(6), cmd_que(1)
Back to the commit discussion.. on the ses_get_power_status() call
introduced in ses_enclosure_data_process(): impact of removing it.
That may possibly be in place to initialize the power status value
on device probe. However, those 2 functions available to retrieve
that value _do_ automatically refresh/update it. So the potential
benefit would be a direct access of the 'power_status' field which
does not use the callbacks...
But the only reader of 'struct enclosure_component::power_status'
is the get_component_power_status() callback for sysfs attribute,
and it _does_ check for and call the .get_power_status callback,
(which indeed is defined and implemented by that commit), so the
power status value is, again, automatically updated.
So, the remaining potential for a direct/non-callback access to
the power_status attribute would be out-of-tree modules -- well,
for those, if they are for whatever reason interested in values
that are set during device probe and not up-to-date by the time
they need it.. well, that would be curious.
Well, to handle that more properly, set the initial power state
value to '-1' (i.e., uninitialized) instead of '1' (power 'on'),
and check for it in that callback which may do an direct access
to the field value _if_ a callback function is not defined.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Fixes: 08024885a2 ("ses: Add power_status to SES device slot")
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8820a4cf0c ]
At a commit 9dc5d31cdc ("ALSA: firewire-digi00x: handle MIDI messages in
isochronous packets"), a functionality to handle MIDI messages on
isochronous packet was supported. But this includes some of my
misunderstanding. This commit is to fix them.
For digi00x series, first data channel of data blocks in rx/tx packet
includes MIDI messages. The data channel has 0x80 in 8 bit of its MSB,
however it's against IEC 61883-6. Unique data format is applied:
- Upper 4 bits of LSB represent port number.
- 0x0: port 1.
- 0x2: port 2.
- 0xe: console port.
- Lower 4 bits of LSB represent the number of included MIDI message bytes;
0x0/0x1/0x2.
- Two bytes of middle of this data channel have MIDI bytes.
Especially, MIDI messages from/to console surface are also transferred by
isochronous packets, as well as physical MIDI ports.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13e005f9f9 ]
Digi00x series includes two types of unit; rack and console. As long as
reading information on config rom of Digi 002 console, 'MODEL_ID' field
has a different value from the one on Digi 002 rack.
We've already got a test report from users with Digi 003 rack. We can
assume that console type and rack type has different value in the field.
This commit adds a device entry for console type. For following commits,
this commit also adds a member to 'struct snd_digi00x' to identify console
type.
$ cd linux-firewire-utils/src
$ python2 ./crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0404f9d0 bus_info_length 4, crc_length 4, crc 63952
404 31333934 bus_name "1394"
408 60647002 irmc 0, cmc 1, isc 1, bmc 0, cyc_clk_acc 100, max_rec 7 (256)
40c 00a07e00 company_id 00a07e |
410 00a30000 device_id 0000a30000 | EUI-64 00a07e0000a30000
root directory
-----------------------------------------------------------------
414 00058a39 directory_length 5, crc 35385
418 0c0043a0 node capabilities
41c 04000001 hardware version
420 0300a07e vendor
424 81000007 --> descriptor leaf at 440
428 d1000001 --> unit directory at 42c
unit directory at 42c
-----------------------------------------------------------------
42c 00046674 directory_length 4, crc 26228
430 120000a3 specifier id
434 13000001 version
438 17000001 model
43c 81000007 --> descriptor leaf at 458
descriptor leaf at 440
-----------------------------------------------------------------
440 00055913 leaf_length 5, crc 22803
444 000050f2 descriptor_type 00, specifier_ID 50f2
448 80000000
44c 44696769
450 64657369
454 676e0000
descriptor leaf at 458
-----------------------------------------------------------------
458 0004a6fd leaf_length 4, crc 42749
45c 00000000 textual descriptor
460 00000000 minimal ASCII
464 44696769 "Digi"
468 20303032 " 002"
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7b87463edf ]
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
After this patch:
$ modinfo sound/soc/codecs/snd-soc-rt5677.ko | grep alias
alias: of:N*T*Crealtek,rt5677C*
alias: of:N*T*Crealtek,rt5677
alias: i2c:RT5677CE:00
alias: i2c:rt5676
alias: i2c:rt5677
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71b0576bdb ]
Currently canceling of delayed work that flushes old data using
cancel_old_flush() does not prevent work from being requeued. Thus
in theory new work can be queued after cancel_old_flush() from
reiserfs_freeze() has run. This will become larger problem once
flush_old_commits() can requeue the work itself.
Fix the problem by recording in sbi->work_queue that flushing work is
canceled and should not be requeued.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6dd47cfd03 ]
The driver currently handles vblank events only when updating planes on
a CRTC. The atomic update API however allows requesting an event when
disabling a CRTC. This currently leads to event objects being leaked in
the kernel and to events not being sent out. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 257ab44311 ]
Some console drivers code calls console_conditional_schedule()
that looks at @console_may_schedule. The value must be cleared
when the drivers are called from console_unlock() with
interrupts disabled. But rescheduling is fine when the same
code is called, for example, from tty operations where the
console semaphore is taken via console_lock().
This is why @console_may_schedule is cleared before calling console
drivers. The original value is stored to decide if we could sleep
between lines.
Now, @console_may_schedule is not cleared when we call
console_trylock() and jump back to the "again" goto label.
This has become a problem, since the commit 6b97a20d3a
("printk: set may_schedule for some of console_trylock() callers").
@console_may_schedule might get enabled now.
There is also the opposite problem. console_lock() can be called
only from preemptive context. It can always enable scheduling in
the console code. But console_trylock() is not able to detect it
when CONFIG_PREEMPT_COUNT is disabled. Therefore we should use the
original @console_may_schedule value after re-acquiring
the console semaphore in console_unlock().
This patch solves both problems by moving the "again" goto label.
Alternative solution was to clear and restore the value around
call_console_drivers(). Then console_conditional_schedule() could
be used also inside console_unlock(). But there was a potential race
with console_flush_on_panic() as reported by Sergey Senozhatsky.
That function should be called only where there is only one CPU
and with interrupts disabled. But better be on the safe side
because stopping CPUs might fail.
Fixes: 6b97a20d3a ("printk: set may_schedule for some of console_trylock() callers")
Link: http://lkml.kernel.org/r/1490372045-22288-1-git-send-email-pmladek@suse.com
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44531ba45d ]
When configuring the HW timers block we should set the number of CIDs
up until the last CID that require timers, instead of only those CIDs
whose protocol needs timers support.
Today, the protocols that require HW timers' support have their CIDs
before any other protocol, but that would change in future [when we
add iWARP support].
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d39004ab13 ]
Breaking the include loop netdevice.h, dsa.h, devlink.h broke this
driver, it depends on includes brought in by these headers. Adding
linux/of.h fixes it.
Fixes: ed0e39e97d34 ("net: break include loop netdevice.h, dsa.h, devlink.h")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a7a9dcd882 ]
Early on in do_page_fault() we call store_updates_sp(), regardless of
the type of exception. For an instruction miss this doesn't make
sense, because we only use this information to detect if a data miss
is the result of a stack expansion instruction or not.
Worse still, it results in a data miss within every userspace
instruction miss handler, because we try and load the very instruction
we are about to install a pte for!
A simple exec microbenchmark runs 6% faster on POWER8 with this fix:
#include <stdlib.h>
#include <stdio.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
unsigned long left = atol(argv[1]);
char leftstr[16];
if (left-- == 0)
return 0;
sprintf(leftstr, "%ld", left);
execlp(argv[0], argv[0], leftstr, NULL);
perror("exec failed\n");
return 0;
}
Pass the number of iterations on the command line (eg 10000) and time
how long it takes to execute.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d916d92372 ]
Including linux/unaligned/access_ok.h causes the allmodconfig build on
ia64 (and maybe others) to fail with the following warnings:
include/linux/unaligned/access_ok.h:7:19: error: redefinition of 'get_unaligned_le16'
include/linux/unaligned/access_ok.h:12:19: error: redefinition of 'get_unaligned_le32'
include/linux/unaligned/access_ok.h:17:19: error: redefinition of 'get_unaligned_le64'
include/linux/unaligned/access_ok.h:22:19: error: redefinition of 'get_unaligned_be16'
include/linux/unaligned/access_ok.h:27:19: error: redefinition of 'get_unaligned_be32'
include/linux/unaligned/access_ok.h:32:19: error: redefinition of 'get_unaligned_be64'
include/linux/unaligned/access_ok.h:37:20: error: redefinition of 'put_unaligned_le16'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_le32'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_le64'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be16'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be32'
include/linux/unaligned/access_ok.h:42:20: error: redefinition of 'put_unaligned_be64'
Fix these by including asm/unaligned.h instead and leave it up to the
architecture to decide how to implement unaligned accesses.
Fixes: 3194c68701 ("NFC: nfcmrvl: add firmware download support")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Link: https://lkml.org/lkml/2016/10/22/247
Cc: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6acfeb17d ]
vxlan dev currently ignores lowerdev's gso_max_size, which adversely
affects TSO performance of liquidio if it's the lowerdev. Egress TCP
packets' skb->len often exceed liquidio's advertised gso_max_size. This
may happen on other NIC drivers.
Fix it by assigning lowerdev's gso_max_size to that of vxlan dev. Might as
well do likewise for gso_max_segs.
Single flow TSO throughput of liquidio as lowerdev (using iperf3):
Before the patch: 139 Mbps
After the patch : 8.68 Gbps
Percent increase: 6,144 %
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aa74f0687c ]
1. When unsetting a mode, num_connector should be set to zero
2. The pixel_format field needs to be initialized as newer DRM internal
functions checks this field
3. Take the drm_modeset_lock_all() because vmw_fb_kms_detach() can
change current mode
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ed2b8621b ]
commit bbeddf52ad ("printk: move braille console support into
separate braille.[ch] files") introduced _braille_console_setup()
to outline the braille initialization code. There was however some
confusion over the value it was supposed to return. commit 2cfe6c4ac7
("printk: Fix return of braille_register_console()") tried to fix it
but failed to.
This fixes and documents the returned value according to the use
in printk.c: non-zero return means a parsing error, and thus this
console configuration should be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Cc: Joe Perches <joe@perches.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a525108cf1 ]
Without this if firmware reports 1MB page size support we will crash
trying to use 1MB as hugetlb page size.
echo 300 > /sys/kernel/mm/hugepages/hugepages-1024kB/nr_hugepages
kernel BUG at ./arch/powerpc/include/asm/hugetlb.h:19!
.....
....
[c0000000e2c27b30] c00000000029dae8 .hugetlb_fault+0x638/0xda0
[c0000000e2c27c30] c00000000026fb64 .handle_mm_fault+0x844/0x1d70
[c0000000e2c27d70] c00000000004805c .do_page_fault+0x3dc/0x7c0
[c0000000e2c27e30] c00000000000ac98 handle_page_fault+0x10/0x30
With fix, we don't enable 1MB as hugepage size.
bash-4.2# cd /sys/kernel/mm/hugepages/
bash-4.2# ls
hugepages-16384kB hugepages-16777216kB
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 142c6594ac ]
Some device drivers reset their stats at down/up events, possibly
fooling bonding stats, since they operate with relative deltas.
It is nearly not possible to fix drivers, since some of them compute the
tx/rx counters based on per rx/tx queue stats, and the queues can be
reconfigured (ethtool -L) between the down/up sequence.
Lets avoid accumulating 'negative' values that render bonding stats
useless.
It is better to lose small deltas, assuming the bonding stats are
fetched at a reasonable frequency.
Fixes: 5f0c5f73e5 ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2c139cf43 ]
Fixes a potential race condition in amdgpu that looks as follows:
Task 1: attempt ttm_bo_init, but ttm_bo_validate fails
Task 1: add BO to global list anyway
Task 2: grabs hold of the BO, waits on its reservation lock
Task 1: releases its reference of the BO; never gives up the
reservation lock
The patch "drm/amdgpu: fix a potential deadlock in
amdgpu_bo_create_restricted()" attempts to fix that by releasing
the reservation lock in amdgpu code; unfortunately, it introduces
a use-after-free when this race _doesn't_ happen.
This patch should fix the race properly by never adding the BO
to the global list in the first place.
Cc: zhoucm1 <david1.zhou@amd.com>
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Tested-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c13ff37e35 ]
- has_not_enough_free_secs
node_secs: 0 dent_secs: 0 freed:0 free_segments:103 reserved:104
- f2fs_gc
- get_victim_by_default
alloc_mode 0, gc_mode 1, max_search 2672, offset 4654, ofs_unit 1
- do_garbage_collect
start_segno 3976, end_segno 3977 type 0
- is_alive
nid 22797, blkaddr 2131882, ofs_in_node 0, version 0x8/0x0
- gc_data_segment 766, segno 3976, block 512/426 not alive
So, this patch fixes subtle corrupted case where node version does not match
to summary version which results in infinite loop by gc.
Reported-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd2b297514 ]
Which may happen when we start a tracing session and a thread is waiting
for something like "poll" to return, in which case we better print "?"
both for the syscall entry timestamp and for the duration.
E.g.:
Tracing existing mutt session:
# perf trace -p `pidof mutt`
? ( ? ): mutt/17135 ... [continued]: poll()) = 1
0.027 ( 0.013 ms): mutt/17135 read(buf: 0x7ffcb3c42cef, count: 1) = 1
0.047 ( 0.008 ms): mutt/17135 poll(ufds: 0x7ffcb3c42c50, nfds: 1, timeout_msecs: 1000) = 1
0.059 ( 0.008 ms): mutt/17135 read(buf: 0x7ffcb3c42cef, count: 1) = 1
<SNIP>
Before it would print a large number because we'd do:
ttrace->entry_time - trace->base_time
And entry_time would be 0, while base_time would be the timestamp for
the first event 'perf trace' reads, oops.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Luis Claudio Gonçalves <lclaudio@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-wbcb93ofva2qdjd5ltn5eeqq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd08604555 ]
Commit 26988efe11 ("regulator: core: Allow to get voltage count and
list from parent") introduces the propagation of the parent voltage
count and list for regulators that don't provide this information
themselves. The goal is to support simple switch regulators, however as
a side effect normal continuous regulators can leak details of their
supplies and provide consumers with inconsistent information.
Limit the propagation of the voltage count and list to switch
regulators.
Fixes: 26988efe11 ("regulator: core: Allow to get voltage count and
list from parent")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 06cceedcca ]
cgroup could be throttled to a limit but when all cgroups cross high
limit, queue enters a higher state and so the group should be throttled
to a higher limit. It's possible the cgroup is sleeping because of
throttle and other cgroups don't dispatch IO any more. In this case,
nobody can trigger current downgrade/upgrade logic. To fix this issue,
we could either set up a timer to wakeup the cgroup if other cgroups are
idle or make sure this cgroup doesn't sleep too long. Setting up a timer
means we must change the timer very frequently. This patch chooses the
latter. Making cgroup sleep time not too big wouldn't change cgroup
bps/iops, but could make it wakeup more frequently, which isn't a big
issue because throtl_slice * 8 is already quite big.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
