[ Upstream commit 4d6b1c95b9 ]
According to NVMe spec v1.4, section 8.3.1, the PRINFO bit and
the metadata size play a vital role in deteriming the host buffer size.
If PRIFNO bit is set and MS==8, the host doesn't add the metadata buffer,
instead the controller adds it.
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cdc4a6950 ]
When the capacity of the disc is too large (assuming the 4.7G
specification), the disc (UDF file system) will be burned
multiple times in the windows (Multisession Usage). When the
remaining capacity of the CD is less than 300M (estimated
value, for reference only), open the CD in the Linux system,
the content of the CD is displayed as blank (the kernel will
say "No VRS found"). Windows can display the contents of the
CD normally.
Through analysis, in the "fs/udf/super.c": udf_check_vsd
function, the actual value of VSD_MAX_SECTOR_OFFSET may
be much larger than 0x800000. According to the current code
logic, it is found that the type of sbi->s_session is "__s32",
when the remaining capacity of the disc is less than 300M
(take a set of test values: sector=3154903040,
sbi->s_session=1540464, sb->s_blocksize_bits=11 ), the
calculation result of "sbi->s_session << sb->s_blocksize_bits"
will overflow. Therefore, it is necessary to convert the
type of s_session to "loff_t" (when udf_check_vsd starts,
assign a value to _sector, which is also converted in this
way), so that the result will not overflow, and then the
content of the disc can be displayed normally.
Link: https://lore.kernel.org/r/20210114075741.30448-1-changlianzhi@uniontech.com
Signed-off-by: lianzhi chang <changlianzhi@uniontech.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3a0828d4 ]
VI I2C controller has known hardware bug where immediate multiple
writes to TX_FIFO register gets stuck.
Recommended software work around is to read I2C register after
each write to TX_FIFO register to flush out the data.
This patch implements this work around for VI I2C controller.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764907293e ]
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
-- Linux partition suspended for > 30 seconds --
-> for_each_online_cpu(cpu)
plpar_hcall_norets(H_PROD
-> scsi_dispatch_cmd
-> scsi_times_out
-> scsi_abort_command
-> queue_delayed_work
-> ibmvfc_queuecommand_lck
-> ibmvfc_send_event
-> ibmvfc_send_crq
- returns H_CLOSED
<- returns SCSI_MLQUEUE_HOST_BUSY
-> __blk_mq_requeue_request
-> scmd_eh_abort_handler
-> scsi_try_to_abort_cmd
- returns SUCCESS
-> scsi_queue_insert
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
Link: https://lore.kernel.org/r/1610463998-19791-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6020d534fa ]
This fixes strlen mismatch problems happening in some .write callbacks
of debugfs.
When trying to configure airtime_flags in debugfs, an error appeared:
ash: write error: Invalid argument
The error is returned from kstrtou16() since a wrong length makes it
miss the real end of input string. To fix this, use count as the string
length, and set proper end of string for a char buffer.
The debug print is shown - airtime_flags_write: count = 2, len = 8,
where the actual length is 2, but "len = strlen(buf)" gets 8.
Also cleanup the other similar cases for the sake of consistency.
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://lore.kernel.org/r/20210112032028.7482-1-shayne.chen@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2e38dffcd ]
Building with the Clang assembler shows the following warning:
arch/x86/kernel/ftrace_64.o: warning: objtool: missing symbol for insn at offset 0x16
The Clang assembler strips section symbols. That ends up giving
objtool's find_func_containing() much more test coverage than normal.
Turns out, find_func_containing() doesn't work so well for overlapping
symbols:
2: 000000000000000e 0 NOTYPE LOCAL DEFAULT 2 fgraph_trace
3: 000000000000000f 0 NOTYPE LOCAL DEFAULT 2 trace
4: 0000000000000000 165 FUNC GLOBAL DEFAULT 2 __fentry__
5: 000000000000000e 0 NOTYPE GLOBAL DEFAULT 2 ftrace_stub
The zero-length NOTYPE symbols are inside __fentry__(), confusing the
rbtree search for any __fentry__() offset coming after a NOTYPE.
Try to avoid this problem by not adding zero-length symbols to the
rbtree. They're rare and aren't needed in the rbtree anyway.
One caveat, this actually might not end up being the right fix.
Non-empty overlapping symbols, if they exist, could have the same
problem. But that would need bigger changes, let's see if we can get
away with the easy fix for now.
Reported-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b0f16fa6 ]
A race condition exists between the response handler getting called because
of exchange_mgr_reset() (which clears out all the active XIDs) and the
response we get via an interrupt.
Sequence of events:
rport ba0200: Port timeout, state PLOGI
rport ba0200: Port entered PLOGI state from PLOGI state
xid 1052: Exchange timer armed : 20000 msecs xid timer armed here
rport ba0200: Received LOGO request while in state PLOGI
rport ba0200: Delete port
rport ba0200: work event 3
rport ba0200: lld callback ev 3
bnx2fc: rport_event_hdlr: event = 3, port_id = 0xba0200
bnx2fc: ba0200 - rport not created Yet!!
/* Here we reset any outstanding exchanges before
freeing rport using the exch_mgr_reset() */
xid 1052: Exchange timer canceled
/* Here we got two responses for one xid */
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
Skip the response if the exchange is already completed.
Link: https://lore.kernel.org/r/20201215194731.2326-1-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9d4ef6434 ]
When doing dma_alloc_coherent in the driver, we add a certain hard-coded
offset to the DMA address before returning to the callee function. This
offset is needed when our device use this DMA address to perform
outbound transactions to the host.
However, if we want to map the DMA'able memory to the user via
dma_mmap_coherent(), we need to pass the original dma address, without
this offset. Otherwise, we will get erronouos mapping.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46c54cf270 ]
The Estar Beauty HD (MID 7316R) tablet uses a Goodix touchscreen,
with the X and Y coordinates swapped compared to the LCD panel.
Add a touchscreen_dmi entry for this adding a "touchscreen-swapped-x-y"
device-property to the i2c-client instantiated for this device before
the driver binds.
This is the first entry of a Goodix touchscreen to touchscreen_dmi.c,
so far DMI quirks for Goodix touchscreen's have been added directly
to drivers/input/touchscreen/goodix.c. Currently there are 3
DMI tables in goodix.c:
1. rotated_screen[] for devices where the touchscreen is rotated
180 degrees vs the LCD panel
2. inverted_x_screen[] for devices where the X axis is inverted
3. nine_bytes_report[] for devices which use a non standard touch
report size
Arguably only 3. really needs to be inside the driver and the other
2 cases are better handled through the generic touchscreen DMI quirk
mechanism from touchscreen_dmi.c, which allows adding device-props to
any i2c-client. Esp. now that goodix.c is using the generic
touchscreen_properties code.
Alternative to the approach from this patch we could add a 4th
dmi_system_id table for devices with swapped-x-y axis to goodix.c,
but that seems undesirable.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201224135158.10976-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f981dc171c ]
When BIOS disables turbo, The scaling_max_freq in cpufreq sysfs will be
limited to config level 0 base frequency. But when user selects a higher
config levels, this will result in higher base frequency. But since
scaling_max_freq is still old base frequency, the performance will still
be limited. So when the turbo is disabled and cpufreq base_frequency is
higher than scaling_max_freq, update the scaling_max_freq to the
base_frequency.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20201221071859.2783957-2-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764257d906 ]
On deferred probe, we will get the following splat:
cpcap-usb-phy cpcap-usb-phy.0: could not initialize VBUS or ID IIO: -517
WARNING: CPU: 0 PID: 21 at drivers/regulator/core.c:2123 regulator_put+0x68/0x78
...
(regulator_put) from [<c068ebf0>] (release_nodes+0x1b4/0x1fc)
(release_nodes) from [<c068a9a4>] (really_probe+0x104/0x4a0)
(really_probe) from [<c068b034>] (driver_probe_device+0x58/0xb4)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201230102105.11826-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 29b3283972 upstream.
When an Intel IOMMU is virtualized, and a physical device is
passed-through to the VM, changes of the virtual IOMMU need to be
propagated to the physical IOMMU. The hypervisor therefore needs to
monitor PTE mappings in the IOMMU page-tables. Intel specifications
provide "caching-mode" capability that a virtual IOMMU uses to report
that the IOMMU is virtualized and a TLB flush is needed after mapping to
allow the hypervisor to propagate virtual IOMMU mappings to the physical
IOMMU. To the best of my knowledge no real physical IOMMU reports
"caching-mode" as turned on.
Synchronizing the virtual and the physical IOMMU tables is expensive if
the hypervisor is unaware which PTEs have changed, as the hypervisor is
required to walk all the virtualized tables and look for changes.
Consequently, domain flushes are much more expensive than page-specific
flushes on virtualized IOMMUs with passthrough devices. The kernel
therefore exploited the "caching-mode" indication to avoid domain
flushing and use page-specific flushing in virtualized environments. See
commit 78d5f0f500 ("intel-iommu: Avoid global flushes with caching
mode.")
This behavior changed after commit 13cf017446 ("iommu/vt-d: Make use
of iova deferred flushing"). Now, when batched TLB flushing is used (the
default), full TLB domain flushes are performed frequently, requiring
the hypervisor to perform expensive synchronization between the virtual
TLB and the physical one.
Getting batched TLB flushes to use page-specific invalidations again in
such circumstances is not easy, since the TLB invalidation scheme
assumes that "full" domain TLB flushes are performed for scalability.
Disable batched TLB flushes when caching-mode is on, as the performance
benefit from using batched TLB invalidations is likely to be much
smaller than the overhead of the virtual-to-physical IOMMU page-tables
synchronization.
Fixes: 13cf017446 ("iommu/vt-d: Make use of iova deferred flushing")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210127175317.1600473-1-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20776b465c upstream.
It's not true that switchdev_port_obj_notify() only inspects the
->handled field of "struct switchdev_notifier_port_obj_info" if
call_switchdev_blocking_notifiers() returns 0 - there's a WARN_ON()
triggering for a non-zero return combined with ->handled not being
true. But the real problem here is that -EOPNOTSUPP is not being
properly handled.
The wrapper functions switchdev_handle_port_obj_add() et al change a
return value of -EOPNOTSUPP to 0, and the treatment of ->handled in
switchdev_port_obj_notify() seems to be designed to change that back
to -EOPNOTSUPP in case nobody actually acted on the notifier (i.e.,
everybody returned -EOPNOTSUPP).
Currently, as soon as some device down the stack passes the check_cb()
check, ->handled gets set to true, which means that
switchdev_port_obj_notify() cannot actually ever return -EOPNOTSUPP.
This, for example, means that the detection of hardware offload
support in the MRP code is broken: switchdev_port_obj_add() used by
br_mrp_switchdev_send_ring_test() always returns 0, so since the MRP
code thinks the generation of MRP test frames has been offloaded, no
such frames are actually put on the wire. Similarly,
br_mrp_switchdev_set_ring_role() also always returns 0, causing
mrp->ring_role_offloaded to be set to 1.
To fix this, continue to set ->handled true if any callback returns
success or any error distinct from -EOPNOTSUPP. But if all the
callbacks return -EOPNOTSUPP, make sure that ->handled stays false, so
the logic in switchdev_port_obj_notify() can propagate that
information.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Fixes: f30f0601eb ("switchdev: Add helpers to aid traversal through lower devices")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20210125124116.102928-1-rasmus.villemoes@prevas.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6f6881aaf upstream.
The purpose of the delayed work in the SPAN module is to potentially
update the destination port and various encapsulation parameters of SPAN
agents that point to a VLAN device or a GRE tap. The destination port
can change following the insertion of a new route, for example.
SPAN agents that point to a physical port or the CPU port are static and
never change throughout the lifetime of the SPAN agent. Therefore, skip
over them in the delayed work.
This fixes an issue where the delayed work overwrites the policer
that was set on a SPAN agent pointing to the CPU. Modifying the delayed
work to inherit the original policer configuration is error-prone, as
the same will be needed for any new parameter.
Fixes: 4039504e6a ("mlxsw: spectrum_span: Allow setting policer on a SPAN agent")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db2805150a upstream.
The octeontx2 hardware needs the buffer to be 128 byte aligned.
But in the current implementation of napi_alloc_frag(), it can't
guarantee the return address is 128 byte aligned even the request size
is a multiple of 128 bytes, so we have to request an extra 128 bytes and
use the PTR_ALIGN() to make sure that the buffer is aligned correctly.
Fixes: 7a36e4918e ("octeontx2-pf: Use the napi_alloc_frag() to alloc the pool buffers")
Reported-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20210121070906.25380-1-haokexin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c45ba93d3 upstream.
KSZ8794CNX datasheet section 8.0 RESET CIRCUIT describes recommended
circuit for interfacing with CPU/FPGA reset consisting of 10k pullup
resistor and 10uF capacitor to ground. This circuit takes ~100 ms to
rise enough to release the reset.
For maximum supply voltage VDDIO=3.3V VIH=2.0V R=10kR C=10uF that is
VDDIO - VIH
t = R * C * -ln( ------------- ) = 10000*0.00001*-(-0.93)=0.093 s
VDDIO
so we need ~95 ms for the reset to really de-assert, and then the
original 100us for the switch itself to come out of reset. Simply
msleep() for 100 ms which fits the constraint with a bit of extra
space.
Fixes: 5b79798090 ("net: dsa: microchip: Implement recommended reset timing")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210120030502.617185-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c518adafa3 upstream.
There are multiple similar bugs implicitly introduced by the
commit c0cfa2d8a7 ("vsock: add multi-transports support") and
commit 6a2c096210 ("vsock: prevent transport modules unloading").
The bug pattern:
[1] vsock_sock.transport pointer is copied to a local variable,
[2] lock_sock() is called,
[3] the local variable is used.
VSOCK multi-transport support introduced the race condition:
vsock_sock.transport value may change between [1] and [2].
Let's copy vsock_sock.transport pointer to local variables after
the lock_sock() call.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Link: https://lore.kernel.org/r/20210201084719.2257066-1-alex.popov@linux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62d9f1a694 upstream.
Upon receiving a cumulative ACK that changes the congestion state from
Disorder to Open, the TLP timer is not set. If the sender is app-limited,
it can only wait for the RTO timer to expire and retransmit.
The reason for this is that the TLP timer is set before the congestion
state changes in tcp_ack(), so we delay the time point of calling
tcp_set_xmit_timer() until after tcp_fastretrans_alert() returns and
remove the FLAG_SET_XMIT_TIMER from ack_flag when the RACK reorder timer
is set.
This commit has two additional benefits:
1) Make sure to reset RTO according to RFC6298 when receiving ACK, to
avoid spurious RTO caused by RTO timer early expires.
2) Reduce the xmit timer reschedule once per ACK when the RACK reorder
timer is set.
Fixes: df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Link: https://lore.kernel.org/netdev/1611311242-6675-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1611464834-23030-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 344db93ae3 upstream.
The TCP_USER_TIMEOUT is checked by the 0-window probe timer. As the
timer has backoff with a max interval of about two minutes, the
actual timeout for TCP_USER_TIMEOUT can be off by up to two minutes.
In this patch the TCP_USER_TIMEOUT is made more accurate by taking it
into account when computing the timer value for the 0-window probes.
This patch is similar to and builds on top of the one that made
TCP_USER_TIMEOUT accurate for RTOs in commit b701a99e43 ("tcp: Add
tcp_clamp_rto_to_user_timeout() helper to improve accuracy").
Fixes: 9721e709fa ("tcp: simplify window probe aborting on USER_TIMEOUT")
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210122191306.GA99540@localhost.localdomain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0947d0d21 upstream.
Function __team_compute_features() is protected by team->lock
mutex when it is called from team_compute_features() used when
features of an underlying device is changed. This causes
a deadlock when NETDEV_FEAT_CHANGE notifier for underlying device
is fired due to change propagated from team driver (e.g. MTU
change). It's because callbacks like team_change_mtu() or
team_vlan_rx_{add,del}_vid() protect their port list traversal
by team->lock mutex.
Example (r8169 case where this driver disables TSO for certain MTU
values):
...
[ 6391.348202] __mutex_lock.isra.6+0x2d0/0x4a0
[ 6391.358602] team_device_event+0x9d/0x160 [team]
[ 6391.363756] notifier_call_chain+0x47/0x70
[ 6391.368329] netdev_update_features+0x56/0x60
[ 6391.373207] rtl8169_change_mtu+0x14/0x50 [r8169]
[ 6391.378457] dev_set_mtu_ext+0xe1/0x1d0
[ 6391.387022] dev_set_mtu+0x52/0x90
[ 6391.390820] team_change_mtu+0x64/0xf0 [team]
[ 6391.395683] dev_set_mtu_ext+0xe1/0x1d0
[ 6391.399963] do_setlink+0x231/0xf50
...
In fact team_compute_features() called from team_device_event()
does not need to be protected by team->lock mutex and rcu_read_lock()
is sufficient there for port list traversal.
Fixes: 3d249d4ca7 ("net: introduce ethernet teaming device")
Cc: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20210125074416.4056484-1-ivecera@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
