[ Upstream commit eb63ecc170 ]
Locally originated traffic in a VRF fails in the presence of a POSTROUTING
rule. For example,
$ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE
$ ping -I red -c1 11.1.1.3
ping: Warning: source address might be selected on device other than red.
PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data.
ping: sendmsg: Operation not permitted
Worse, the above causes random corruption resulting in a panic in random
places (I have not seen a consistent backtrace).
Call nf_reset to drop the conntrack info following the pass through the
VRF device. The nf_reset is needed on Tx but not Rx because of the order
in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress
device and on Tx it is is before the real egress device. Connection
tracking should be tied to the real egress device and not the VRF device.
Fixes: 8f58336d3f ("net: Add ethernet header for pass through VRF device")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93a97c50cb ]
If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.
Fixes: 2869b23e4b ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a50af86dd4 ]
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eaa496ffaa upstream.
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4349bd775c upstream.
We were storing viewport relative coordinates for AVIVO/DCE display
engines. However, radeon_crtc_cursor_set2 and radeon_cursor_reset pass
radeon_crtc->cursor_x/y as the x/y parameters of
radeon_cursor_move_locked, which would break if the CRTC isn't located
at (0, 0).
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0b0faff78 upstream.
Smatch complains about where the au8293_data is placed:
drivers/media/pci/cx23885/cx23885-dvb.c:2174 dvb_register() info: 'a8293_pdata' is not actually initialized (unreached code).
It is not actually expected to have such initialization at
switch {
foo = bar;
case:
...
}
Not really sure how gcc does that, but this is something that I would
expect that different compilers would do different things.
David Howells checked with the compiler people: it's not really expected to
initialise as expected.
So, move the initialization outside the switch(), making smatch to
shut up one warning.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57e7c8cef2 upstream.
When CONFIG_PCI_MSI is disabled, we get warnings about unused functions
in the vxge driver:
drivers/net/ethernet/neterion/vxge/vxge-main.c:2121:13: warning: 'adaptive_coalesce_tx_interrupts' defined but not used [-Wunused-function]
drivers/net/ethernet/neterion/vxge/vxge-main.c:2149:13: warning: 'adaptive_coalesce_rx_interrupts' defined but not used [-Wunused-function]
We could add another #ifdef here, but it's nicer to avoid those warnings
for good by converting the existing #ifdef to if(IS_ENABLED()), which has
the same effect but provides better compile-time coverage in general,
and lets the compiler understand better when the function is intentionally
unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f5281ba2a upstream.
cpmac_start_xmit() used the max() macro on skb->len (an unsigned int)
and ETH_ZLEN (a signed int literal). This led to the following compiler
warning:
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/net/ethernet/ti/cpmac.c:19:
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_start_xmit':
include/linux/kernel.h:748:17: warning: comparison of distinct pointer
types lacks a cast
(void) (&_max1 == &_max2); \
^
drivers/net/ethernet/ti/cpmac.c:560:8: note: in expansion of macro 'max'
len = max(skb->len, ETH_ZLEN);
^
On top of this, it assigned the result of the max() macro to a signed
integer whilst all further uses of it result in it being cast to varying
widths of unsigned integer.
Fix this up by using max_t to ensure the comparison is performed as
unsigned integers, and for consistency change the type of the len
variable to unsigned int.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0335695dfa upstream.
The current_user_ns() macro currently returns &init_user_ns when user
namespaces are disabled, and that causes several warnings when building
with gcc-6.0 in code that compares the result of the macro to
&init_user_ns itself:
fs/xfs/xfs_ioctl.c: In function 'xfs_ioctl_setattr_check_projid':
fs/xfs/xfs_ioctl.c:1249:22: error: self-comparison always evaluates to true [-Werror=tautological-compare]
if (current_user_ns() == &init_user_ns)
This is a legitimate warning in principle, but here it isn't really
helpful, so I'm reprasing the definition in a way that shuts up the
warning. Apparently gcc only warns when comparing identical literals,
but it can figure out that the result of an inline function can be
identical to a constant expression in order to optimize a condition yet
not warn about the fact that the condition is known at compile time.
This is exactly what we want here, and it looks reasonable because we
generally prefer inline functions over macros anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6b1160eb2 upstream.
Arnd Bergmann pointed out that gcc-6 warns about passing negative signed
integer into swab16() due to the macro expansion of 'outw'.
It appears that the register map constants are causing the warnings.
Actually, it might just be the (1 << 15) ones...
Convert all the constants as suggested by checkpatch.pl:
CHECK: Prefer using the BIT macro
The BIT() macro will make all the constants explicitly 'unsigned', which
helps to avoid the warning.
Fix the, unsused, DT2821_CHANCSR_PRESLA() macro. The "Present List
Address" (PRESLA) bits in the CHANCSR register are read only. This
define was meant to extract the bits from the read value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99e5cde5ea upstream.
Make sure to drop any device reference taken by vio_find_node() when
adding and removing virtual I/O slots.
Fixes: 5eeb8c63a3 ("[PATCH] PCI Hotplug: rpaphp: Move VIO registration")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1803b9a52c upstream.
The core AES cipher implementation that uses ARMv8 Crypto Extensions
instructions erroneously loads the round keys as 64-bit quantities,
which causes the algorithm to fail when built for big endian. In
addition, the key schedule generation routine fails to take endianness
into account as well, when loading the combining the input key with
the round constants. So fix both issues.
Fixes: 12ac3efe74 ("arm64/crypto: use crypto instructions to generate AES key schedule")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caf4b9e2b3 upstream.
Emit the XTS tweak literal constants in the appropriate order for a
single 128-bit scalar literal load.
Fixes: 49788fe2a1 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee71e5f1e7 upstream.
The SHA1 digest is an array of 5 32-bit quantities, so we should refer
to them as such in order for this code to work correctly when built for
big endian. So replace 16 byte scalar loads and stores with 4x4 vector
ones where appropriate.
Fixes: 2c98833a42 ("arm64/crypto: SHA-1 using ARMv8 Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2c435cc99 upstream.
The AES implementation using pure NEON instructions relies on the generic
AES key schedule generation routines, which store the round keys as arrays
of 32-bit quantities stored in memory using native endianness. This means
we should refer to these round keys using 4x4 loads rather than 16x1 loads.
In addition, the ShiftRows tables are loading using a single scalar load,
which is also affected by endianness, so emit these tables in the correct
order depending on whether we are building for big endian or not.
Fixes: 49788fe2a1 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56e4e76c68 upstream.
The AES-CCM implementation that uses ARMv8 Crypto Extensions instructions
refers to the AES round keys as pairs of 64-bit quantities, which causes
failures when building the code for big endian. In addition, it byte swaps
the input counter unconditionally, while this is only required for little
endian builds. So fix both issues.
Fixes: 12ac3efe74 ("arm64/crypto: use crypto instructions to generate AES key schedule")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58010fa6f7 upstream.
The AES key schedule generation is mostly endian agnostic, with the
exception of the rotation and the incorporation of the round constant
at the start of each round. So implement a big endian specific version
of that part to make the whole routine big endian compatible.
Fixes: 86464859cc ("crypto: arm - AES in ECB/CBC/CTR/XTS modes using ARMv8 Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c433ad508 upstream.
The GHASH key and digest are both pairs of 64-bit quantities, but the
GHASH code does not always refer to them as such, causing failures when
built for big endian. So replace the 16x1 loads and stores with 2x8 ones.
Fixes: b913a6404c ("arm64/crypto: improve performance of GHASH algorithm")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 174122c39c upstream.
The SHA256 digest is an array of 8 32-bit quantities, so we should refer
to them as such in order for this code to work correctly when built for
big endian. So replace 16 byte scalar loads and stores with 4x32 vector
ones where appropriate.
Fixes: 6ba6c74dfc ("arm64/crypto: SHA-224/SHA-256 using ARMv8 Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bed570307e upstream.
I noticed some wakeirq flakeyness with consumer drivers not using
autosuspend. For drivers not using autosuspend, the wakeirq may never
get unmasked in rpm_suspend() because of irq desc->depth.
We are configuring dedicated wakeirqs to start with IRQ_NOAUTOEN as we
naturally don't want them running until rpm_suspend() is called.
However, when a consumer driver initially calls pm_runtime_get(), we
now wrongly start with disable_irq_nosync() call on the dedicated
wakeirq that is disabled to start with.
This causes desc->depth to toggle between 1 and 2 instead of the usual
0 and 1. This can prevent enable_irq() from unmasking the wakeirq as
that only happens at desc->depth 1.
This does not necessarily show up with drivers using autosuspend as
there is time for disable_irq_nosync() before rpm_suspend() gets called
after the autosuspend timeout.
Let's fix the issue by adding wirq->status that lazily gets set on
the first rpm_suspend(). We also need PM runtime core private functions
for dev_pm_enable_wake_irq_check() and dev_pm_disable_wake_irq_check()
so we can enable the dedicated wakeirq on the first rpm_suspend().
While at it, let's also fix the comments for dev_pm_enable_wake_irq()
and dev_pm_disable_wake_irq(). Those can still be used by the consumer
drivers as needed because the IRQ core manages the interrupt usecount
for us.
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a91918cd3e upstream.
This iscsit_tpg_add_portal_group() function is only called from
lio_target_tiqn_addtpg(). Both functions free the "tpg" pointer on
error so it's a double free bug. The memory is allocated in the caller
so it should be freed in the caller and not here.
Fixes: e48354ce07 ("iscsi-target: Add iSCSI fabric support for target v4.1")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Disseldorp <ddiss@suse.de>
[ bvanassche: Added "Fix" at start of patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af15769ffa upstream.
gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:
drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.
Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.
Fixes: a4632aae8b ("[SCSI] mvsas: Add new macros and functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5faf071d08 upstream.
Unfortunately, I seem to have missed a case where an IRQ safe spinlock was
required, in samsung_i2s_dai_remove, when I fixed up the other calls in
this patch:
316fa9e09a ("ASoC: samsung: Use IRQ safe spin lock calls")
This causes a lockdep warning when unbinding and rebinding the audio card:
[ 104.357664] CPU0 CPU1
[ 104.362174] ---- ----
[ 104.366692] lock(&(&pri_dai->spinlock)->rlock);
[ 104.371372] local_irq_disable();
[ 104.377283] lock(&(&substream->self_group.lock)->rlock);
[ 104.385259] lock(&(&pri_dai->spinlock)->rlock);
[ 104.392469] <Interrupt>
[ 104.395072] lock(&(&substream->self_group.lock)->rlock);
[ 104.400710]
[ 104.400710] *** DEADLOCK ***
Fixes: ce8bcdbb61 ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec0e86172 upstream.
We met the DMAR fault both on hpsa P420i and P421 SmartArray controllers
under kdump, it can be steadily reproduced on several different machines,
the dmesg log is like:
HP HPSA Driver (v 3.4.16-0)
hpsa 0000:02:00.0: using doorbell to reset controller
hpsa 0000:02:00.0: board ready after hard reset.
hpsa 0000:02:00.0: Waiting for controller to respond to no-op
DMAR: Setting identity map for device 0000:02:00.0 [0xe8000 - 0xe8fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xf4000 - 0xf4fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6e000 - 0xbdf6efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf6f000 - 0xbdf7efff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf7f000 - 0xbdf82fff]
DMAR: Setting identity map for device 0000:02:00.0 [0xbdf83000 - 0xbdf84fff]
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read] Request device [02:00.0] fault addr fffff000 [fault reason 06] PTE Read access is not set
hpsa 0000:02:00.0: controller message 03:00 timed out
hpsa 0000:02:00.0: no-op failed; re-trying
After some debugging, we found that the fault addr is from DMA initiated at
the driver probe stage after reset(not in-flight DMA), and the corresponding
pte entry value is correct, the fault is likely due to the old iommu caches
of the in-flight DMA before it.
Thus we need to flush the old cache after context mapping is setup for the
device, where the device is supposed to finish reset at its driver probe
stage and no in-flight DMA exists hereafter.
I'm not sure if the hardware is responsible for invalidating all the related
caches allocated in the iommu hardware before, but seems not the case for hpsa,
actually many device drivers have problems in properly resetting the hardware.
Anyway flushing (again) by software in kdump kernel when the device gets context
mapped which is a quite infrequent operation does little harm.
With this patch, the problematic machine can survive the kdump tests.
CC: Myron Stowe <myron.stowe@gmail.com>
CC: Joseph Szczypek <jszczype@redhat.com>
CC: Don Brace <don.brace@microsemi.com>
CC: Baoquan He <bhe@redhat.com>
CC: Dave Young <dyoung@redhat.com>
Fixes: 091d42e43d ("iommu/vt-d: Copy translation tables from old kernel")
Fixes: dbcd861f25 ("iommu/vt-d: Do not re-use domain-ids from the old kernel")
Fixes: cf484d0e69 ("iommu/vt-d: Mark copied context entries")
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65ca7f5f7d upstream.
Different encodings are used to represent supported PASID bits
and number of PASID table entries.
The current code assigns ecap_pss directly to extended context
table entry PTS which is wrong and could result in writing
non-zero bits to the reserved fields. IOMMU fault reason
11 will be reported when reserved bits are nonzero.
This patch converts ecap_pss to extend context entry pts encoding
based on VT-d spec. Chapter 9.4 as follows:
- number of PASID bits = ecap_pss + 1
- number of PASID table entries = 2^(pts + 5)
Software assigned limit of pasid_max value is also respected to
match the allocation limitation of PASID table.
cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Fixes: 2f26e0a9c9 ('iommu/vt-d: Add basic SVM PASID support')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 432abf68a7 upstream.
The generic command buffer entry is 128 bits (16 bytes), so the offset
of tail and head pointer should be 16 bytes aligned and increased with
0x10 per command.
When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE.
So when left space of cmd buf should be able to store only two
command, we should be issued one COMPLETE_WAIT additionally to wait
all older commands completed. Then the left space should be increased
after IOMMU fetching from cmd buf.
So left check value should be left <= 0x20 (two commands).
Signed-off-by: Huang Rui <ray.huang@amd.com>
Fixes: ac0ea6e92b ('x86/amd-iommu: Improve handling of full command buffer')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bae203d58b upstream.
Function mx31_clocks_init() is called during clock intialization on
legacy boards with reference clock frequency passed as its input
argument, this can be verified by examination of the function
declaration found in arch/arm/mach-imx/common.h and actual function
users which include that header file.
Inside CCF driver the function ignores its input argument, by chance
the used value in the function body is the same as input arguments on
side of all callers.
Fixes: d9388c8432 ("clk: imx31: Do not call mxc_timer_init twice when booting with DT")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fccd4a1e8 upstream.
Fix overflows seen when writing into fan speed limit attributes.
Also fix crash due to division by zero, seen when certain very
large values (such as 2147483648, or 0x80000000) are written
into fan speed limit attributes.
Fixes: 594fbe713b ("Add support for GMT G762/G763 PWM fan controllers")
Cc: Arnaud Ebalard <arno@natisbad.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0d04e9112 upstream.
Fix overflows seen when writing voltage and temperature limit attributes.
The value passed to DIV_ROUND_CLOSEST() needs to be clamped, and the
value parameter passed to nct7802_write_fan_min() is an unsigned long.
Also, writing values larger than 2700000 into a fan limit attribute results
in writing 0 into the chip's limit registers. The exact behavior when
writing this value is unspecified. For consistency, report a limit of
1350000 if the chip register reads 0. This may be wrong, and the chip
behavior should be verified with the actual chip, but it is better than
reporting a value of 0 (which, when written, results in writing a value
of 0x1fff into the chip register).
Fixes: 3434f37835 ("hwmon: Driver for Nuvoton NCT7802Y")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e36ce99ee0 upstream.
Module test reports:
temp1_max: Suspected overflow: [160000 vs. 0]
temp1_min: Suspected overflow: [160000 vs. 0]
This is seen because the values passed when writing temperature limits
are unbound.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Fixes: 6099469805 ("hwmon: Support for Dallas Semiconductor DS620")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4538bfbf2d upstream.
Converts the unsigned temperature values from the i2c read
to be sign extended as defined in the datasheet so that
negative temperatures are properly read.
Fixes: 28e6274d8f ("hwmon: (amc6821) Avoid forward declaration")
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
[groeck: Dropped unnecessary continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13edb767aa upstream.
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
$
After this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
alias: of:N*T*Carm,scpi-sensorsC*
alias: of:N*T*Carm,scpi-sensors
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Fixes: ea98b29a05 ("hwmon: Support sensors exported via ARM SCP interface")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 328cf6927b upstream.
If CONFIG_ETRAX_AXISFLASHMAP is not configured, the flash rescue image
object file is empty. With recent versions of binutils, this results
in the following build error.
cris-linux-objcopy: error:
the input file 'arch/cris/boot/rescue/rescue.o' has no sections
This is seen, for example, when trying to build cris:allnoconfig
with recently generated toolchains.
Since it does not make sense to build a flash rescue image if there is
no flash, only build it if CONFIG_ETRAX_AXISFLASHMAP is enabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 66ab3a74c5 ("CRIS: Merge machine dependent boot/compressed ..")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31b239824e upstream.
The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed1220 ("ath10k: add spectral scan feature")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[resolves a messed up backport, so no matching upstream commit]
The backport of upstream commit 777c6e0dae ("hotplug: Make
register and unregister notifier API symmetric") to linux-4.4.y
introduced a harmless warning in 'allnoconfig' builds as spotted by
kernelci.org:
kernel/cpu.c:226:13: warning: 'cpu_notify_nofail' defined but not used [-Wunused-function]
So far, this is the only stable tree that is affected, as linux-4.6 and
higher contain commit 984581728e ("cpu/hotplug: Split out cpu down functions")
that makes the function used in all configurations, while older longterm
releases so far don't seem to have a backport of 777c6e0dae.
The fix for the warning is trivial: move the unused function back
into the #ifdef section where it was before.
Link: https://kernelci.org/build/id/586fcacb59b514049ef6c3aa/logs/
Fixes: 1c0f4e0ebb ("hotplug: Make register and unregister notifier API symmetric") in v4.4.y
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19ec31230e upstream.
Let's call dwc3_ep0_prepare_one_trb() explicitly
because there are occasions where we will need more
than one TRB to handle an EP0 transfer.
A follow-up patch will fix one bug related to
multiple-TRB Data Phases when it comes to
mapping/unmapping requests for DMA.
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7931ec86c1 upstream.
For now this is just a cleanup patch, no functional
changes. We will be using the new function to fix a
bug introduced long ago by commit 0416e494ce
("usb: dwc3: ep0: correct cache sync issue in case
of ep0_bounced") and further worsened by commit
c0bd5456a4 ("usb: dwc3: ep0: handle non maxpacket
aligned transfers > 512")
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d621459299 upstream.
commit 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.
Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.
Fixes: 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced")
Cc: <stable@vger.kernel.org>
Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b321a38d24 upstream.
The oversampling ratio is controlled using the oversampling pins,
OS [2:0] with OS2 being the MSB control bit, and OS0 the LSB control
bit.
The gpio connected to the OS2 pin is not being set correctly, only OS0
and OS1 pins are being set. Fix the typo to allow proper control of the
oversampling pins.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com>
Fixes: b9618c0 ("staging: IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4")
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
