[ Upstream commit 755a5b805f ]
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56d3746247 ]
With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8875ca356 ]
With the current driver, the statistics reported by .ndo_get_stats64()
are reset when the device goes down. Store a snapshot of the
rtnl_link_stats64 before shutdown. This snapshot is added to the
current counters in .ndo_get_stats64() so that the counters will not
get reset when the device is down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c675421af ]
Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8294059931 ]
Each media stream negotiation between 2 SIP peers will trigger creation
of 4 different expectations (2 RTP and 2 RTCP):
- INVITE will create expectations for the media packets sent by the
called peer
- reply to the INVITE will create expectations for media packets sent
by the caller
The dport used by these expectations usually match the ones selected
by the SIP peers, but they might get translated due to conflicts with
another expectation. When such event occur, it is important to do
this translation in both directions, dport translation on the receiving
path and sport translation on the sending path.
This commit fixes the sport translation when the peer requiring it is
also the one that starts the media stream. In this scenario, first media
stream packet is forwarded from LAN to WAN and will rely on
nf_nat_sip_expected() to do the necessary sport translation. However, the
expectation matched by this packet does not contain the necessary information
for doing SNAT, this data being stored in the paired expectation created by
the sender's SIP message (INVITE or reply to it).
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b4924da47 ]
This patch is based on commit a86caa9ba5 ("pinctrl: msm: fix gpio-hog
related boot issues").
It fixes the issue that the gpio ranges needs to be defined before
gpiochip_add().
Therefore, we also have to swap the order of registering the pinctrl
driver and registering the gpio chip.
You also have to add the "gpio-ranges" property to the pinctrl device
node to get it finally working.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0752e9c30 ]
Commit 21abf10381
("gpio: Pass a flag to gpiochip_request_own_desc()")
started to pass an enum gpiod_flags but this file is
not including the header file that defines that enum
and the compiler spits:
drivers/memory/omap-gpmc.c: In function
'gpmc_probe_generic_child':
drivers/memory/omap-gpmc.c:2174:9: error: type of formal
parameter 4 is incomplete
0);
^
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 21abf10381 ("gpio: Pass a flag to gpiochip_request_own_desc()")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ba35b3a00 ]
Clang warns:
samples/vfio-mdev/mtty.c:592:39: warning: implicit conversion from 'int'
to 'char' changes value from 162 to -94 [-Wconstant-conversion]
*buf = UART_MSR_DSR | UART_MSR_DDSR | UART_MSR_DCD;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
1 warning generated.
Turns out that all uses of buf in this function ultimately end up stored
or cast to an unsigned type. Just use u8, which has the same number of
bits but can store this larger number so Clang no longer warns.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7f677a2a ]
When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the characters to the workqueue
for the tty layer to handle them. When this busy time on the serial/tty
subsystem happens during boot, where it is also busy on the userspace
trying to initialise, some processes can continuously get preempted
and will be on hold until the interrupts subside.
The fix is to backoff on processing received characters for a specified
amount of time when an input overrun is seen (received a new character
before the previous one is processed). This only stops receive and will
continue to transmit characters to serial port. After the backoff period
is done, it receive will be re-enabled. This is optional and will only
be enabled by setting 'overrun-throttle-ms' in the dts.
Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85af74c474 ]
We're getting a reference RPi's firmware node in order to be able to
communicate with it's driver. We should decrease the reference count on
the dt node after being done with it.
Fixes: a98d90e7d5 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e0856d317 ]
The memory chunk allocated by hid_allocate_device() should be released
by hid_destroy_device(), not kfree().
Fixes: 0b28cb4bcb1("HID: intel-ish-hid: ISH HID client driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e948218b7 ]
When falling back to PIO, active_rx must be set to a different value
than cookie_rx[i], else sci_dma_rx_find_active() will incorrectly find a
match, leading to a NULL pointer dereference in rx_timer_fn() later.
Use zero instead, which is the same value as after driver
initialization.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 158ffa364b ]
We use this number to figure out how many delayed refs to run, but
__btrfs_run_delayed_refs really only checks every time we need a new
delayed ref head, so we always run at least one ref head completely no
matter what the number of items on it. Fix the accounting to only be
adjusted when we add/remove a ref head.
In addition to using this number to limit the number of delayed refs
run, a future patch is also going to use it to calculate the amount of
space required for delayed refs space reservation.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6ec385b5 ]
We can have a lot freed extents during the life span of transaction, so
the red black tree that keeps track of the ranges of each freed extent
(fs_info->freed_extents[]) can get quite big. When finishing a
transaction commit we find each range, process it (discard the extents,
unpin them) and then remove it from the red black tree.
We can use an extent state record as a cache when searching for a range,
so that when we clean the range we can use the cached extent state we
passed to the search function instead of iterating the red black tree
again. Doing things as fast as possible when finishing a transaction (in
state TRANS_STATE_UNBLOCKED) is convenient as it reduces the time we
block another task that wants to commit the next transaction.
So change clear_extent_dirty() to allow an optional extent state record to
be passed as an argument, which will be passed down to __clear_extent_bit.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b47dda2ef6 ]
The device-replace needs to check the result code of the scrub workers
in btrfs_dev_replace_cancel and distinguish if successful cancel
operation and when the there was no operation running.
If btrfs_scrub_cancel() fails, return
BTRFS_IOCTL_DEV_REPLACE_RESULT_NOT_STARTED so that user can try
to cancel the replace again.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da612e31ae ]
RAID5 and RAID6 profile store one copy of the data, not 2 or 3. These
values are not yet used anywhere so there's no change.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Hans van Kranenburg <hans.van.kranenburg@mendix.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8a168aa9 ]
Before btrfs_map_bio submits all stripe bios it does a number of checks
to ensure the device for every stripe is present. However, it doesn't do
a DEV_STATE_MISSING check, instead this is relegated to the lower level
btrfs_schedule_bio (in the async submission case, sync submission
doesn't check DEV_STATE_MISSING at all). Additionally
btrfs_schedule_bios does the duplicate device->bdev check which has
already been performed in btrfs_map_bio.
This patch moves the DEV_STATE_MISSING check in btrfs_map_bio and
removes the duplicate device->bdev check. Doing so ensures that no bio
cloning/submission happens for both async/sync requests in the face of
missing device. This makes the async io submission path slightly shorter
in terms of instruction count. No functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8dc7623bf6 ]
PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.
If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.
This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.
Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 732774437a ]
The opcodes used by the controller when doing batched page prog should
be written in NFC_REG_WCMD_SET not FC_REG_RCMD_SET. Luckily, the
default NFC_REG_WCMD_SET value matches the one we set in the driver
which explains why we didn't notice the problem.
Fixes: 614049a8d9 ("mtd: nand: sunxi: add support for DMA assisted operations")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18f92bc02f ]
On errors, if we don't stop the descriptor chain, it may continue to
run and raise IRQ after we have called mmc_request_done(). This is bad
because we won't be able to get cmd anymore and properly deal with the
IRQ.
This patch makes sure the descriptor chain is stopped before
calling mmc_request_done()
Fixes: 79ed05e329 ("mmc: meson-gx: add support for descriptor chain mode")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8236b08cf5 ]
The old code always starts from fixed port for VMADDR_PORT_ANY. Sometimes
when VMM crashed, there is still orphaned vsock which is waiting for
close timer, then it could cause connection time out for new started VM
if they are trying to connect to same port with same guest cid since the
new packets could hit that orphaned vsock. We could also fix this by doing
more in vhost_vsock_reset_orphans, but any way, it should be better to start
from a random local port instead of a fixed one.
Signed-off-by: Lepton Wu <ytht.net@gmail.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6422ccc5fb ]
listen fails when more than one tls capable device is
registered. tls_hw_hash is called for each dev which loops
again for each cdev_list causing listen failure. Hence
call chtls_listen_start/stop for specific device than loop over all
devices.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5510b8daf ]
If CONFIG_GPOILIB is not set, the stub of gpio_to_desc() should return
the same type of error as regular version: NULL. All the callers
compare the return value of gpio_to_desc() against NULL, so returned
ERR_PTR would be treated as non-error case leading to dereferencing of
error value.
Fixes: 79a9becda8 ("gpiolib: export descriptor-based GPIO interface")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92f45ebe68 ]
The PCAL_PINCTRL_MASK is too large. The extended register block on
PCAL6524, which is the largest chip with this block, has the block
limited to address range 0x40..0x7f. This is because the bit 7 in
the command register is used for the Address Increment functionality.
Trim the mask to 0x60 to match the datasheet and to prevent accidental
overwrite of the AI bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 956343a612 ]
command len is set too early in the code, since when building
AMSDU, the size changes. This causes the byte count table to
have the wrong size.
Fixes: a0ec0169b7 ("iwlwifi: support new tx api")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0916224eaa ]
When removing the driver, the following flow can happen:
1. host command is in progress, for example at index 68.
2. RX interrupt is received with the response.
3. Before it is processed, the remove flow kicks in, and
calls iwl_pcie_txq_unmap. The function cleans all DMA,
and promotes the read pointer to 69.
4. RX thread proceeds with the processing, and is calling
iwl_pcie_cmdq_reclaim, which will print this error:
iwl_pcie_cmdq_reclaim: Read index for DMA queue txq id (0),
index 4 is out of range [0-256] 69 69.
Detect this situation, and avoid the print. Change it to
warning while at it, to make such issues more noticeable
in the future.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bc2468277 ]
When traffic load is not low or low latency is active, TCM schedules
re-evaluation work so in case traffic stops TCM will detect that
traffic load has become low or that low latency is no longer active.
However, if TCM is paused when the re-evaluation work runs, it does
not re-evaluate and the re-evaluation work is no longer scheduled.
As a result, TCM will not indicate that low latency is no longer
active or that traffic load is low when traffic stops.
Fix this by forcing TCM re-evaluation when TCM is resumed in case
low latency is active or traffic load is not low.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64866e5da1 ]
This function is only half-used by mvm (i.e. only the nvm_version part
matters, since the calibration version is irrelevant), so it's
pointless to export it from iwlwifi. If mvm uses this function, it
has the additional complexity of setting the calib version to a bogus
value on all cfg structs.
To avoid this, move the function to dvm and make a simple comparison
of the nvm_version in mvm instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4722a3e6b7 ]
This commit fixes some build issues.
The first issue is the breakage of linux.bin.ub target since commit
ece97f3a5f ("microblaze: Fix simpleImage format generation")
because the addition of UIMAGE_{IN,OUT} affected it.
make ARCH=microblaze CROSS_COMPILE=microblaze-linux- linux.bin.ub
[ snip ]
OBJCOPY arch/microblaze/boot/linux.bin
UIMAGE arch/microblaze/boot/linux.bin.ub.ub
/usr/bin/mkimage: Can't open arch/microblaze/boot/linux.bin.ub: No such file or directory
make[1]: *** [arch/microblaze/boot/Makefile;14: arch/microblaze/boot/linux.bin.ub] Error 1
make: *** [arch/microblaze/Makefile;83: linux.bin.ub] Error 2
The second issue is the use of the "if_changed" multiple times for
the same target.
As commit 92a4728608 ("x86/boot: Fix if_changed build flip/flop bug")
pointed out, this never works properly. Moreover, generating multiple
images as a side-effect is confusing.
Let's split the build recipe for each image.
simpleImage.<dt>*.unstrip is just a copy of vmlinux.
simpleImage.<dt> and simpleImage.<dt>.ub are created in the same way
as linux.bin and linux.bin.ub, respectively.
I kept simpleImage.* recipes independent of linux.bin.* ones to not
change the behavior.
Lastly, this commit fixes "make ARCH=microblaze clean". Previously,
it only cleaned up the unstrip image. Now, all the simpleImage files
are cleaned.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e14f94cf4 ]
To prepare for more fixes, move this to arch/microblaze/Makefile.
Otherwise, the same "... is ready" would be printed multiple times.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bafcc61d99 ]
"make ARCH=microblaze help" mentions simpleImage.<dt>.unstrip,
but it is not a real Make target. It does not work because Makefile
assumes "system.unstrip" is the name of DT.
$ make ARCH=microblaze CROSS_COMPILE=microblaze-linux- simpleImage.system.unstrip
[ snip ]
make[1]: *** No rule to make target 'arch/microblaze/boot/dts/system.unstrip.dtb', needed by 'arch/microblaze/boot/dts/system.dtb'. Stop.
make: *** [Makefile;1060: arch/microblaze/boot/dts] Error 2
make: *** Waiting for unfinished jobs....
simpleImage.<dt> works like a phony target that generates multiple
images. Reflect the real behavior. I removed the DT directory path
information because it is already explained a few lines below.
While I am here, I deleted the redundant *_defconfig explanation.
The top-level Makefile caters to list available defconfig files:
mmu_defconfig - Build for mmu
nommu_defconfig - Build for nommu
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e542087701 ]
The UBI device reference is dropped but then the device is used as a
parameter of ubi_err. The bug is introduced in changing ubi_err's
behavior. The old ubi_err does not require a UBI device as its first
parameter, but the new one does.
Fixes: 3260870331 ("UBI: Extend UBI layer debug/messaging capabilities")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b95f83ab76 ]
The MTD device reference is dropped via put_mtd_device, however its
field ->index is read and passed to ubi_msg. To fix this, the patch
moves the reference dropping after calling ubi_msg.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d62e98ed1e ]
When ubifs is build without the LZO compressor and no compressor is
given the creation of the default file system will fail. before
selection the LZO compressor check if it is present and if not fall back
to the zlib or none.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64bafd2f1e ]
Since mkfs always formats the filesystem with the realtime bitmap and
summary inodes immediately after the root directory, we should expect
that both of them are present and loadable, even if there isn't a
realtime volume attached. There's no reason to skip this if rbmino ==
NULLFSINO; in fact, this causes an immediate crash if the there /is/ a
realtime volume and someone writes to it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79b791466e ]
A fresh backing device is not attached to any cache_set, and
has no writeback kthread created until first attached to some
cache_set.
But bch_cached_dev_writeback_init run
"
dc->writeback_running = true;
WARN_ON(test_and_clear_bit(BCACHE_DEV_WB_RUNNING,
&dc->disk.flags));
"
for any newly formatted backing devices.
For a fresh standalone backing device, we can get something like
following even if no writeback kthread created:
------------------------
/sys/block/bcache0/bcache# cat writeback_running
1
/sys/block/bcache0/bcache# cat writeback_rate_debug
rate: 512.0k/sec
dirty: 0.0k
target: 0.0k
proportional: 0.0k
integral: 0.0k
change: 0.0k/sec
next io: -15427384ms
The none ZERO fields are misleading as no alive writeback kthread yet.
Set dc->writeback_running false as no writeback thread created in
bch_cached_dev_writeback_init().
We have writeback thread created and woken up in bch_cached_dev_writeback
_start(). Set dc->writeback_running true before bch_writeback_queue()
called, as a writeback thread will check if dc->writeback_running is true
before writing back dirty data, and hung if false detected.
After the change, we can get the following output for a fresh standalone
backing device:
-----------------------
/sys/block/bcache0/bcache$ cat writeback_running
0
/sys/block/bcache0/bcache# cat writeback_rate_debug
rate: 0.0k/sec
dirty: 0.0k
target: 0.0k
proportional: 0.0k
integral: 0.0k
change: 0.0k/sec
next io: 0ms
v1 -> v2:
Set dc->writeback_running before bch_writeback_queue() called,
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae17102316 ]
debugfs_remove and debugfs_remove_recursive will check if the dentry
pointer is NULL or ERR, and will do nothing in that case.
Remove the check in cache_set_free and bch_debug_init.
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afbb1947db ]
entry is released via usb_put_urb just after calling usb_submit_urb.
However, entry is used if the submission fails, resulting in a use after
free bug. The patch fixes this.
Signed-off-by: Pan Bian <bianpan2016@163.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
