[ Upstream commit dd8f7fa908 ]
If ANA is enabled but no ANA group descriptor is found when creating
a new namespace the ANA log is most likely out of date, so trigger
a re-read. The namespace will be tagged with the NS_ANA_PENDING flag
to exclude it from path selection until the ANA log has been re-read.
Fixes: 32acab3181 ("nvme: implement multipath access to nvme subsystems")
Reported-by: Martin George <marting@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04722cec14 ]
Currently POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT and
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE are exposed on
the battery node and this is incorrect.
This patch exposes both of them on the charger node rather
than the battery node.
Fixes: 5069185fc1 ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 379c9a24cc ]
Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.
clk: failed to reparent uart1 to sys_pll1_80m: -16
Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.
When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.
Fixes: 9461f7b33d ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b73b45d54 ]
The TCP stack can run from process context for a long time
so we should disable BH here.
Fixes: 3f2304f8c6 ("nvme-tcp: add NVMe over TCP host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6471a65fd ]
The function mv_platform_probe() neglects to check the results of the
calls to platform_get_irq() and irq_of_parse_and_map() and blithely
passes them to ata_host_activate() -- while the latter only checks
for IRQ0 (treating it as a polling mode indicattion) and passes the
negative values to devm_request_irq() causing it to fail as it takes
unsigned values for the IRQ #...
Add to mv_platform_probe() the proper IRQ checks to pass the positive IRQ
#s to ata_host_activate(), propagate upstream the negative error codes,
and override the IRQ0 with -EINVAL (as we don't want the polling mode).
Fixes: f351b2d638 ("sata_mv: Support SoC controllers")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/51436f00-27a1-e20b-c21b-0e817e0a7c86@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e379b40cc0 ]
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking
code to pass the positive IRQ #s to ata_host_activate(), propagate errors
upstream, and treat IRQ0 as error, returning -EINVAL, as the libata code
treats 0 as an indication that polling should be used anyway...
Fixes: 0df0d0a0ea ("[libata] ARM: add ixp4xx PATA driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e8f404d5 ]
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking code
to pass the positive IRQ #s to ata_host_activate(), propagate upstream
-EPROBE_DEFER, and set up the driver to polling mode on (negative) errors
and IRQ0 (libata treats IRQ #0 as a polling mode anyway)...
Fixes: a480167b23 ("pata_arasan_cf: Adding support for arasan compact flash host controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb4969e6f9 ]
Currently the following command produces an error message:
linux# make kselftest TARGETS=bpf O=/mnt/linux-build
# selftests: bpf: test_libbpf.sh
# ./test_libbpf.sh: line 23: ./test_libbpf_open: No such file or directory
# test_libbpf: failed at file test_l4lb.o
# selftests: test_libbpf [FAILED]
The error message might not affect the return code of make, therefore
one needs to grep make output in order to detect it.
This is not the only instance of the same underlying problem; any test
with more than one element in $(TEST_PROGS) fails the same way. Another
example:
linux# make O=/mnt/linux-build TARGETS=splice kselftest
[...]
# ./short_splice_read.sh: 15: ./splice_read: not found
# FAIL: /sys/module/test_module/sections/.init.text 2
not ok 2 selftests: splice: short_splice_read.sh # exit=1
The current logic prepends $(OUTPUT) only to the first member of
$(TEST_PROGS). After that, run_one() does
cd `dirname $TEST`
For all tests except the first one, `dirname $TEST` is ., which means
they cannot access the files generated in $(OUTPUT).
Fix by using $(addprefix) to prepend $(OUTPUT)/ to each member of
$(TEST_PROGS).
Fixes: 1a940687e4 ("selftests: lib.mk: copy test scripts and test files for make O=dir run")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dd3b8c9f5 ]
There are 2 bugs in the can_boost() function because of using
x86 insn decoder. Since the insn->opcode never has a prefix byte,
it can not find CS override prefix in it. And the insn->attr is
the attribute of the opcode, thus inat_is_address_size_prefix(
insn->attr) always returns false.
Fix those by checking each prefix bytes with for_each_insn_prefix
loop and getting the correct attribute for each prefix byte.
Also, this removes unlikely, because this is a slow path.
Fixes: a8d11cd071 ("kprobes/x86: Consolidate insn decoder users for copying code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/161666691162.1120877.2808435205294352583.stgit@devnote2
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e87068570 ]
Using 'imply AMD_IOMMU_V2' does not guarantee that the driver can link
against the exported functions. If the GPU driver is built-in but the
IOMMU driver is a loadable module, the kfd_iommu.c file is indeed
built but does not work:
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_bind_process_to_device':
kfd_iommu.c:(.text+0x516): undefined reference to `amd_iommu_bind_pasid'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_unbind_process':
kfd_iommu.c:(.text+0x691): undefined reference to `amd_iommu_unbind_pasid'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_suspend':
kfd_iommu.c:(.text+0x966): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0x97f): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0x9a4): undefined reference to `amd_iommu_free_device'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_resume':
kfd_iommu.c:(.text+0xa9a): undefined reference to `amd_iommu_init_device'
x86_64-linux-ld: kfd_iommu.c:(.text+0xadc): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xaff): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xc72): undefined reference to `amd_iommu_bind_pasid'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe08): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe26): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe42): undefined reference to `amd_iommu_free_device'
Use IS_REACHABLE to only build IOMMU-V2 support if the amd_iommu symbols
are reachable by the amdkfd driver. Output a warning if they are not,
because that may not be what the user was expecting.
Fixes: 64d1c3a43a ("drm/amdkfd: Centralize IOMMUv2 code and make it conditional")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16a5dcf7fb ]
Inside alloc_user_pages() based on flag value either pin_user_pages()
or get_user_pages_fast() will be called. However, these API might fail.
But free_user_pages() called in error handling path doesn't bother
about return value and will try to unpin bo->pgnr pages, which is
incorrect.
Fix this by passing the page_nr to free_user_pages(). If page_nr > 0
pages will be unpinned based on bo->mem_type. This will also take care
of non error handling path.
allocation")
Link: https://lore.kernel.org/linux-media/1601219284-13275-1-git-send-email-jrdr.linux@gmail.com
Fixes: 14a638ab96 ("media: atomisp: use pin_user_pages() for memory
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c451ee146d ]
The media bus bit width of MEDIA_BUS_FMT_RGB101010_1X30 is 30.
So, 'Bit31' and 'Bit30' cells for the 'MEDIA_BUS_FMT_RGB101010_1X30'
row should be spaces instead of '0's.
Fixes: 54f38fcae5 ("media: docs: move uAPI book to userspace-api/media")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e61f9ea271 ]
In case of error, the function i2c_new_dummy_device() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: e6089feca4 ("media: m88ds3103: Add support for ds3103b demod")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3d384e366 ]
When sun6i_video_remote_subdev() returns NULL to subdev, no error return
code of sun6i_video_start_streaming() is assigned.
To fix this bug, ret is assigned with -EINVAL in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 5cc7522d89 ("media: sun6i: Add support for Allwinner CSI V3s")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a465c5391 ]
If an error occurs after a successful 'of_icc_get()' call, it must be
undone.
Use 'devm_of_icc_get()' instead of 'of_icc_get()' to avoid the leak.
Update the remove function accordingly and axe the now unneeded
'icc_put()' calls.
Fixes: 32f0a6ddc8 ("media: venus: Use on-chip interconnect API")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3536169f85 ]
Video engine uses eclk and vclk for its clock sources and its reset
control is coupled with eclk so the current clock enabling sequence works
like below.
Enable eclk
De-assert Video Engine reset
10ms delay
Enable vclk
It introduces improper reset on the Video Engine hardware and eventually
the hardware generates unexpected DMA memory transfers that can corrupt
memory region in random and sporadic patterns. This issue is observed
very rarely on some specific AST2500 SoCs but it causes a critical
kernel panic with making a various shape of signature so it's extremely
hard to debug. Moreover, the issue is observed even when the video
engine is not actively used because udevd turns on the video engine
hardware for a short time to make a query in every boot.
To fix this issue, this commit changes the clock handling logic to make
the reset de-assertion triggered after enabling both eclk and vclk. Also,
it adds clk_unprepare call for a case when probe fails.
clk: ast2600: fix reset settings for eclk and vclk
Video engine reset setting should be coupled with eclk to match it
with the setting for previous Aspeed SoCs which is defined in
clk-aspeed.c since all Aspeed SoCs are sharing a single video engine
driver. Also, reset bit 6 is defined as 'Video Engine' reset in
datasheet so it should be de-asserted when eclk is enabled. This
commit fixes the setting.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Fixes: d3d04f6c33 ("clk: Add support for AST2600 SoC")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe8373ca7 ]
When setting the source media bus code in the resizer,
we first check that the current media bus code in the
source is yuv encoded format. This is done by
retrieving the data from the formats list of the isp
entity. This cause a crash when the media bus code on the
source is YUYV8_1_5X8 which is not supported by the isp
entity. Instead we should test the sink format of the resizer
which is guaranteed to be supported by the isp entity.
Fixes: 251b6eebb6 ("media: staging: rkisp1: rsz: Add support to more YUV encoded mbus codes on src pad")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Tested-by: Sebastian Fricke <sebastian.fricke.linux@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e56429b09d ]
The new AMD IOMMU DMA implementation concatenates sglist entries under
certain conditions, and because saa7146 accessed the length member
directly, it did not support this scenario.
This fixes IO_PAGE_FAULTs by using the sg_dma_len macro.
Fixes: be62dbf554 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1cb753c0 ]
The new AMD IOMMU DMA implementation concatenates sglist entries under
certain conditions, and because saa7134 accessed the length member
directly, it did not support this scenario.
This fixes IO_PAGE_FAULTs and choppy DMA audio by using the
sg_dma_len macro.
Fixes: be62dbf554 ("iommu/amd: Convert AMD iommu driver to the dma-iommu api")
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cde22fcc7 ]
Currently the chroma_flags and alpha_flags are being zero'd with a bit-wise
mask and the following statement should be bit-wise or'ing in the new flag
bits but instead is making a direct assignment. Fix this by using the |=
operator rather than an assignment.
Addresses-Coverity: ("Unused value")
Fixes: ef834f7836 ("[media] vivid: add the video capture and output parts")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6494ccb932 ]
In rcu_nmi_enter(), there is an erroneous instrumentation_end() in the
second branch of the "if" statement. Oddly enough, "objtool check -f
vmlinux.o" fails to complain because it is unable to correctly cover
all cases. Instead, objtool visits the third branch first, which marks
following trace_rcu_dyntick() as visited. This commit therefore removes
the spurious instrumentation_end().
Fixes: 04b25a495b ("rcu: Mark rcu_nmi_enter() call to rcu_cleanup_after_idle() noinstr")
Reported-by Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1eb04a87 ]
Fix afs_apply_status() to mask off the irrelevant bits from status->mode
when OR'ing them into i_mode. This can happen when a 3rd party chmod
occurs.
Also fix afs_inode_init_from_status() to mask off the mode bits when
initialising i_mode.
Fixes: 260a980317 ("[AFS]: Add "directory write" support.")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39a2a6eb5c ]
Syzbot reported a handful of occurrences where an sd->nr_balance_failed can
grow to much higher values than one would expect.
A successful load_balance() resets it to 0; a failed one increments
it. Once it gets to sd->cache_nice_tries + 3, this *should* trigger an
active balance, which will either set it to sd->cache_nice_tries+1 or reset
it to 0. However, in case the to-be-active-balanced task is not allowed to
run on env->dst_cpu, then the increment is done without any further
modification.
This could then be repeated ad nauseam, and would explain the absurdly high
values reported by syzbot (86, 149). VincentG noted there is value in
letting sd->cache_nice_tries grow, so the shift itself should be
fixed. That means preventing:
"""
If the value of the right operand is negative or is greater than or equal
to the width of the promoted left operand, the behavior is undefined.
"""
Thus we need to cap the shift exponent to
BITS_PER_TYPE(typeof(lefthand)) - 1.
I had a look around for other similar cases via coccinelle:
@expr@
position pos;
expression E1;
expression E2;
@@
(
E1 >> E2@pos
|
E1 >> E2@pos
)
@cst depends on expr@
position pos;
expression expr.E1;
constant cst;
@@
(
E1 >> cst@pos
|
E1 << cst@pos
)
@script:python depends on !cst@
pos << expr.pos;
exp << expr.E2;
@@
# Dirty hack to ignore constexpr
if exp.upper() != exp:
coccilib.report.print_report(pos[0], "Possible UB shift here")
The only other match in kernel/sched is rq_clock_thermal() which employs
sched_thermal_decay_shift, and that exponent is already capped to 10, so
that one is fine.
Fixes: 5a7f555904 ("sched/fair: Relax constraint on task's load during load balance")
Reported-by: syzbot+d7581744d5fd27c9fbe1@syzkaller.appspotmail.com
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: http://lore.kernel.org/r/000000000000ffac1205b9a2112f@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0c5ac04e7 ]
A recent patch renaming MIPI_DSI_MODE_EOT_PACKET to
MIPI_DSI_MODE_NO_EOT_PACKET brought to light the
misunderstanding in the current MCDE driver and all
its associated panel drivers that MIPI_DSI_MODE_EOT_PACKET
would mean "use EOT packet" when in fact it means the
reverse.
Fix it up by implementing the flag right in the MCDE
DSI driver and remove the flag from panels that actually
want the EOT packet.
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Fixes: 5fc537bfd0 ("drm/mcde: Add new driver for ST-Ericsson MCDE")
Fixes: 899f24ed8d ("drm/panel: Add driver for Novatek NT35510-based panels")
Fixes: ac1d6d7488 ("drm/panel: Add driver for Samsung S6D16D0 panel")
Fixes: 435e06c06c ("drm/panel: s6e63m0: Add DSI transport")
Fixes: 8152c2bfd7 ("drm/panel: Add driver for Sony ACX424AKP panel")
Link: https://patchwork.freedesktop.org/patch/msgid/20210304004138.1785057-1-linus.walleij@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e6fafd5a2 ]
The hdcp_i2c_offsets[] array did not have an entry for
HDCP_MESSAGE_ID_WRITE_CONTENT_STREAM_TYPE so it led to an off by one
read overflow. I added an entry and copied the 0x0 value for the offset
from similar code in drivers/gpu/drm/amd/display/modules/hdcp/hdcp_ddc.c.
I also declared several of these arrays as having HDCP_MESSAGE_ID_MAX
entries. This doesn't change the code, but it's just a belt and
suspenders approach to try future proof the code.
Fixes: 4c283fdac0 ("drm/amd/display: Add HDCP module")
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1a75f4dd8 ]
When run xrandr to change resolution on Beaglebone Black board, it will
print the error information:
root@beaglebone:~# xrandr -display :0 --output HDMI-1 --mode 720x400
[drm:drm_crtc_commit_wait] *ERROR* flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:32:tilcdc crtc] commit wait timed out
[drm:drm_crtc_commit_wait] *ERROR* flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CONNECTOR:34:HDMI-A-1] commit wait timed out
[drm:drm_crtc_commit_wait] *ERROR* flip_done timed out
[drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:31:plane-0] commit wait timed out
tilcdc 4830e000.lcdc: already pending page flip!
This is because there is operation sequence as below:
drm_atomic_connector_commit_dpms(mode is DRM_MODE_DPMS_OFF):
...
drm_atomic_helper_setup_commit <- init_completion(commit_A->flip_done)
drm_atomic_helper_commit_tail
tilcdc_crtc_atomic_disable
tilcdc_plane_atomic_update <- drm_crtc_send_vblank_event in tilcdc_crtc_irq
is skipped since tilcdc_crtc->enabled is 0
tilcdc_crtc_atomic_flush <- drm_crtc_send_vblank_event is skipped since
crtc->state->event is set to be NULL in
tilcdc_plane_atomic_update
drm_mode_setcrtc:
...
drm_atomic_helper_setup_commit <- init_completion(commit_B->flip_done)
drm_atomic_helper_wait_for_dependencies
drm_crtc_commit_wait <- wait for commit_A->flip_done completing
Just as shown above, the steps which could complete commit_A->flip_done
are all skipped and commit_A->flip_done will never be completed. This will
result a time-out ERROR when drm_crtc_commit_wait check the commit_A->flip_done.
So add drm_crtc_send_vblank_event in tilcdc_crtc_atomic_disable to
complete commit_A->flip_done.
Fixes: cb345decb4 ("drm/tilcdc: Use standard drm_atomic_helper_commit")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Tested-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Jyri Sarha <jyri.sarha@iki.fi>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209082415.382602-1-quanyang.wang@windriver.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ffa828534 ]
The intent here was to return negative error codes but it actually
returns positive values. The problem is that type promotion with
ternary operations is quite complicated.
"ret" is an int. "copied" is a u32. And the snoop_file_read() function
returns long. What happens is that "ret" is cast to u32 and becomes
positive then it's cast to long and it's still positive.
Fix this by removing the ternary so that "ret" is type promoted directly
to long.
Fixes: 3772e5da44 ("drivers/misc: Aspeed LPC snoop output using misc chardev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Patrick Venture <venture@google.com>
Link: https://lore.kernel.org/r/YIE90PSXsMTa2Y8n@mwanda
Link: https://lore.kernel.org/r/20210423000919.1249474-1-joel@jms.id.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d75e7f63b7 ]
Prior to commit 4a8c31a1c6 ("xen/blkback: rework connect_ring() to avoid
inconsistent xenstore 'ring-page-order' set by malicious blkfront"), the
behaviour of xen-blkback when connecting to a frontend was:
- read 'ring-page-order'
- if not present then expect a single page ring specified by 'ring-ref'
- else expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
This was correct behaviour, but was broken by the afforementioned commit to
become:
- read 'ring-page-order'
- if not present then expect a single page ring (i.e. ring-page-order = 0)
- expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
- if that didn't work then see if there's a single page ring specified by
'ring-ref'
This incorrect behaviour works most of the time but fails when a frontend
that sets 'ring-page-order' is unloaded and replaced by one that does not
because, instead of reading 'ring-ref', xen-blkback will read the stale
'ring-ref0' left around by the previous frontend will try to map the wrong
grant reference.
This patch restores the original behaviour.
Fixes: 4a8c31a1c6 ("xen/blkback: rework connect_ring() to avoid inconsistent xenstore 'ring-page-order' set by malicious blkfront")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: "Roger Pau Monné" <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210202175659.18452-1-paul@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2a5e8448e ]
Data received during half-duplex transmission must be filtered.
If the target device responds quickly, emptying the FIFO at the end of
the transmission can erase not only the echo characters but also part of
the response message.
By keeping the receive interrupt enabled even during transmission, it
allows you to filter each echo character and only in a number equal to
those transmitted.
The issue was generated by a target device that started responding
240us later having received a request in communication at 115200bps.
Sometimes, some messages received by the target were missing some of the
first bytes.
Fixes: 3a13884abe ("tty/serial: omap: empty the RX FIFO at the end of half-duplex TX")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20210418094705.27014-1-dariobin@libero.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24d209dba5 ]
When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.
- Added dwc_handle_gpwrdn_disc_det() function which handles
gpwrdn disconnect detect flow and exits hibernation
without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
calling dwc_handle_gpwrdn_disc_det() function. Here no register
is restored which is the solution described above.
Fixes: 65c9c4c6b0 ("usb: dwc2: Add dwc2_handle_gpwrdn_intr() handler")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124715.75355A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5d1499ae2 ]
Hibernation fails on a system in fips mode because md5 is used for the e820
integrity check and is not available. Use crc32 instead.
The check is intended to detect whether the E820 memory map provided
by the firmware after cold boot unexpectedly differs from the one that
was in use when the hibernation image was created. In this case, the
hibernation image cannot be restored, as it may cover memory regions
that are no longer available to the OS.
A non-cryptographic checksum such as CRC-32 is sufficient to detect such
inadvertent deviations.
Fixes: 62a03defea ("PM / hibernate: Verify the consistent of e820 memory map by md5 digest")
Reviewed-by: Eric Biggers <ebiggers@google.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Chris von Recklinghausen <crecklin@redhat.com>
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77db0ec8b7 ]
When running in Azure, disks may be connected to a Linux VM with
read/write caching enabled. If a VM panics and issues a VMbus
UNLOAD request to Hyper-V, the response is delayed until all dirty
data in the disk cache is flushed. In extreme cases, this flushing
can take 10's of seconds, depending on the disk speed and the amount
of dirty data. If kdump is configured for the VM, the current 10 second
timeout in vmbus_wait_for_unload() may be exceeded, and the UNLOAD
complete message may arrive well after the kdump kernel is already
running, causing problems. Note that no problem occurs if kdump is
not enabled because Hyper-V waits for the cache flush before doing
a reboot through the BIOS/UEFI code.
Fix this problem by increasing the timeout in vmbus_wait_for_unload()
to 100 seconds. Also output periodic messages so that if anyone is
watching the serial console, they won't think the VM is completely
hung.
Fixes: 911e1987ef ("Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/1618894089-126662-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2209ea556 ]
When KEXEC is disabled, the UV build fails:
arch/x86/platform/uv/uv_nmi.c:875:14: error: ‘uv_nmi_kexec_failed’ undeclared (first use in this function)
Since uv_nmi_kexec_failed is only defined in the KEXEC_CORE #ifdef branch,
this code cannot ever have been build tested:
if (main)
pr_err("UV: NMI kdump: KEXEC not supported in this kernel\n");
atomic_set(&uv_nmi_kexec_failed, 1);
Nor is this use possible in uv_handle_nmi():
atomic_set(&uv_nmi_kexec_failed, 0);
These bugs were introduced in this commit:
d0a9964e98: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Which added the uv_nmi_kexec_failed assignments to !KEXEC code, while making the
definition KEXEC-only - apparently without testing the !KEXEC case.
Instead of complicating the #ifdef maze, simplify the code by requiring X86_UV
to depend on KEXEC_CORE. This pattern is present in other architectures as well.
( We'll remove the untested, 7 years old !KEXEC complications from the file in a
separate commit. )
Fixes: d0a9964e98: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 126bdb606f ]
The spi controller supports 44-bit address space on AXI in DMA mode,
so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping.
In addition, if dma_map_single fails, it should return immediately
instead of continuing doing the DMA operation which bases on invalid
address.
This fixes the following crash which occurs in reading a big block
from flash:
[ 123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots)
[ 123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped
[ 123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0
[ 123.792536] Mem abort info:
[ 123.795313] ESR = 0x96000145
[ 123.798351] EC = 0x25: DABT (current EL), IL = 32 bits
[ 123.803655] SET = 0, FnV = 0
[ 123.806693] EA = 0, S1PTW = 0
[ 123.809818] Data abort info:
[ 123.812683] ISV = 0, ISS = 0x00000145
[ 123.816503] CM = 1, WnR = 1
[ 123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000
[ 123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000
[ 123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMP
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-6-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 799f923f0a ]
After calling platform_set_drvdata(pdev, xqspi) in probe, the return
value of dev_get_drvdata(dev) is a pointer to struct zynqmp_qspi but
not struct spi_controller. A wrong structure type passing to the
functions spi_controller_suspend/resume will hang the system.
And we should check the return value of spi_controller_suspend, if
an error is returned, return it to PM subsystem to stop suspend.
Also, GQSPI_EN_MASK should be written to GQSPI_EN_OFST to enable
the spi controller in zynqmp_qspi_resume since it was disabled in
zynqmp_qspi_suspend before.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
