[ Upstream commit dcbf6b18d8 ]
am335x-evm has only one CPSW external port physically wired, but DT defines
2 ext. ports. As result, PHY connection failure reported for the second
ext. port.
Update DT to reflect am335x-evm board HW configuration, and, while here,
switch to use phy-handle instead of phy_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9f36656b5 ]
With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.
By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59739131e0 ]
At OTG work running time, it's possible that several events need to be
addressed (e.g. ID and VBUS events). The current implementation handles
only one event at a time which leads to ignoring the other one. Fix it.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dedbdf2bb ]
When initializing the USB subsystem before starting the kernel,
OTG overcurrent detection is disabled. In case the OTG polarity of
overcurrent is low active, the overcurrent detection is never enabled
again and events cannot be reported as expected. Because imx usb
overcurrent polarity is low active by default, only detection needs
to be enable in usbmisc init function.
Signed-off-by: Nicolas Adell <nicolas.adell@actia.fr>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe72352e37 ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c13b8d1ae ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81255af8d9 ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bacade8225 ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 079cdff3d0 ]
This avoids getting woken up from suspend after power interruptions
when the bci wrongly thinks the battery is full just because
of input current going low because of low input power
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8314c212f9 ]
the charging current uses unsigned int variables, if we step back
if the current is still low, we would run into negative which
means setting the target to a huge value.
Better add checks here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 802fa45cd3 ]
Commit f27b4746f3 ("i40iw: add connection management code") uses an
incorrect rcu iterator, whilst holding the rtnl_lock. Since the
critical region invokes i40iw_manage_qhash(), which is a sleeping
function, the rcu locking and traversal cannot be used.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85a88cabad ]
When performing partition migrations all present CPUs must be online
as all present CPUs must make the H_JOIN call as part of the migration
process. Once all present CPUs make the H_JOIN call, one CPU is returned
to make the rtas call to perform the migration to the destination system.
During testing of migration and changing the SMT state we have found
instances where CPUs are offlined, as part of the SMT state change,
before they make the H_JOIN call. This results in a hung system where
every CPU is either in H_JOIN or offline.
To prevent this this patch disables CPU hotplug during the migration
process.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09b4438db1 ]
This causes SLB alloation to start 1 beyond the start of the SLB.
There is no real problem because after it wraps it stats behaving
properly, it's just surprisig to see when looking at SLB traces.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 984ecdd68d ]
The tbl pointer is being derefenced by IOMMU_PAGE_SIZE prior the check
if it is not NULL.
Just moving the dereference code to after the check, where there will
be guarantee that 'tbl' will not be NULL.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5963e8a312 ]
On the error path of mxs_auart_request_gpio_irq() is performed
backward iterating with index i of enum type. Underline enum type
may be unsigned char. In this case check (--i >= 0) will be always
true and error handling goes into infinite loop.
The patch changes the check so that it is valid for signed and unsigned
types.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ad61b612b ]
If _OSC execution fails today for platforms without an _OSC entry, code is
printing a misleading message saying disabling ASPM as follows:
acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
We need to ensure that platform supports ASPM to begin with.
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d19db777a ]
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e589 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 461cf03605 ]
We tried to revert commit d9c52fd17c ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.
The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.
Fixes: 6df0580be8 ("ath9k: add back support for using active monitor interfaces for tx99")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 131c3eb428 ]
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0350d51f0 ]
gre_parse_header stops parsing when csum_err is encountered, which means
tpi->key is undefined and ip_tunnel_lookup will return NULL improperly.
This patch introduce a NULL pointer as csum_err parameter. Even when
csum_err is encountered, it won't return error and continue parsing gre
header as expected.
Fixes: 9f57c67c37 ("gre: Remove support for sharing GRE protocol hook.")
Reported-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a75e78f21f ]
The terminating NUL byte is only there because the buffer is
allocated with kzalloc(PAGE_SIZE, GFP_KERNEL), but since the
range-check is off-by-one, and PAGE_SIZE==PATH_MAX, the
returned string may not be zero-terminated if it is exactly
PATH_MAX characters long. Furthermore also the initial loop
may theoretically exceed PATH_MAX and cause a fault.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdae566d5d ]
During component_bind_all(), if bind() fails for any
particular component associated with a master, unbind()
should be called for all previous components in that
master's match array, whose bind() might have completed
successfully. As per the current logic, if bind() fails
for the component at position 'n' in the master's match
array, it would start calling unbind() from component in
'n'th position itself and work backwards, and will always
skip calling unbind() for component in 0th position in the
master's match array.
Fix this by updating the loop condition, and the logic to
refer to the components in master's match array, so that
unbind() is called for all components starting from 'n-1'st
position in the array, until (and including) component in
0th position.
Signed-off-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb90a2c6f7 ]
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54baff8d4e ]
If kstrtoul() fails then we print "charge_full" when it's uninitialized.
The debug printk doesn't add anything so I deleted it and cleaned these
two functions up a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3dfa1769 ]
Sharing the same irqchip with multiple gpiochips is not a good
practice. For instance, when installing hooks, we change the state
of the irqchip. The initial state of the irqchip for the second
gpiochip to register is then disrupted.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbbc488ed8 ]
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dtb: Warning (i2c_bus_reg): /soc/i2c@ffc04000/adxl345@0: I2C bus unit address format error, expected "53"
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56d20861c0 ]
Call Frame Information is used by gdb for back-traces and inserting
breakpoints on function return for the "finish" command. This failed
when inside __kernel_clock_gettime. More concerning than difficulty
debugging is that CFI is also used by stack frame unwinding code to
implement exceptions. If you have an app that needs to handle
asynchronous exceptions for some reason, and you are unlucky enough to
get one inside the VDSO time functions, your app will crash.
What's wrong: There is control flow in __kernel_clock_gettime that
reaches label 99 without saving lr in r12. CFI info however is
interpreted by the unwinder without reference to control flow: It's a
simple matter of "Execute all the CFI opcodes up to the current
address". That means the unwinder thinks r12 contains the return
address at label 99. Disabuse it of that notion by resetting CFI for
the return address at label 99.
Note that the ".cfi_restore lr" could have gone anywhere from the
"mtlr r12" a few instructions earlier to the instruction at label 99.
I put the CFI as late as possible, because in general that's best
practice (and if possible grouped with other CFI in order to reduce
the number of CFI opcodes executed when unwinding). Using r12 as the
return address is perfectly fine after the "mtlr r12" since r12 on
that code path still contains the return address.
__get_datapage also has a CFI error. That function temporarily saves
lr in r0, and reflects that fact with ".cfi_register lr,r0". A later
use of r0 means the CFI at that point isn't correct, as r0 no longer
contains the return address. Fix that too.
Signed-off-by: Alan Modra <amodra@gmail.com>
Tested-by: Reza Arbab <arbab@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd73a3dd25 ]
while compiling an ipq4019 target, dtc will complain:
regulator@b089000 unit address format error, expected "2089000"
The saw0 regulator reg value seems to be
copied and pasted from qcom-ipq8064.dtsi.
This patch fixes the reg value to match that of the
unit address which in turn silences the warning.
(There is no driver for qcom,saw2 right now.
So this went unnoticed)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9708d2b5b7 ]
llc_sap_close() is called by llc_sap_put() which
could be called in BH context in llc_rcv(). We can't
block in BH.
There is no reason to block it here, kfree_rcu() should
be sufficient.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b97760ae8e ]
Smatch complains about this condition:
if (has_config && num_pins >= 1)
The "has_config" variable is either uninitialized or true. The
"num_pins" variable is unsigned and we verified that it is non-zero on
the lines before so we know "num_pines >= 1" is true. Really, we could
just check "num_configs" directly and remove the "has_config" variable.
Fixes: 776180848b ("pinctrl: introduce driver for Atmel PIO4 controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7064f376d4 ]
The interrupt handler has to be acquired after the other resource
initialization when allocated with IRQF_SHARED. Otherwise it's
triggered before the resource gets ready, and may lead to unpleasant
behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ccbeeb888 ]
The VIDEO_GET_EVENT and VIDEO_STILLPICTURE was added back in 2005 but
it never worked because the command number is wrong.
Using the right command number means we have a better chance of them
actually doing the right thing, though clearly nobody has ever tried
it successfully.
I noticed these while auditing the remaining users of compat_time_t
for y2038 bugs. This one is fine in that regard, it just never did
anything.
Fixes: 6e87abd0b8 ("[DVB]: Add compat ioctl handling.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eac7230fdb ]
Motion eye video4linux driver for Sony Vaio PictureBook desn't validate user-controlled parameter
'vma->vm_pgoff', a malicious process might access all of kernel memory from user space by trying
pass different arbitrary address.
Discussion: http://www.openwall.com/lists/oss-security/2018/07/06/1
Signed-off-by: Lao Wei <zrlw@qq.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72349b62a5 ]
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a63c1ffd3 ]
For userspace to tell the difference between an random signal
and an exception, the exception must include siginfo information.
Using SEND_SIG_FORCED for SIGSEGV is thus wrong, and it will result in
userspace seeing si_code == SI_USER (like a random signal) instead of
si_code == SI_KERNEL or a more specific si_code as all exceptions
deliver.
Therefore replace force_sig_info(SIGSEGV, SEND_SIG_FORCE, current)
with force_sig(SIG_SEGV, current) which gets this right and is shorter
and easier to type.
Fixes: 791eca1010 ("uretprobes/x86: Hijack return address")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55a3235fc7 ]
For userspace to tell the difference between a random signal and an
exception, the exception must include siginfo information.
Using SEND_SIG_FORCED for SIGILL is thus wrong, and it will result
in userspace seeing si_code == SI_USER (like a random signal) instead
of si_code == SI_KERNEL or a more specific si_code as all exceptions
deliver.
Therefore replace force_sig_info(SIGILL, SEND_SIG_FORCE, current)
with force_sig(SIG_ILL, current) which gets this right and is
shorter and easier to type.
Fixes: 014940bad8 ("uprobes/x86: Send SIGILL if arch_uprobe_post_xol() fails")
Fixes: 0b5256c7f1 ("uprobes: Send SIGILL if handle_trampoline() fails")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86989c41b5 ]
If the first process started (aka /sbin/init) receives a SIGKILL it
will panic the system if it is delivered. Making the system unusable
and undebugable. It isn't much better if the first process started
receives SIGSTOP.
So always ignore SIGSTOP and SIGKILL sent to init.
This is done in a separate clause in sig_task_ignored as force_sig_info
can clear SIG_UNKILLABLE and this protection should work even then.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6df0580be8 ]
Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.
This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter
Fixes: d9c52fd17c ("ath9k: fix tx99 with monitor mode interface")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83ef4fb755 ]
Func jz4780_dma_desc_residue() expects the index to the next hw
descriptor as its last parameter. Caller func jz4780_dma_tx_status(),
however, applied modulus before passing it. When the current hw
descriptor was last in the list, the index passed became zero.
The resulting excess of reported residue especially caused problems
with cyclic DMA transfer clients, i.e. ALSA AIC audio output, which
rely on this for determining current DMA location within buffer.
Combined with the recent and related residue-reporting fixes, spurious
ALSA audio underruns on jz4770 hardware are now fixed.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c558ecd21c ]
If we make this driver depend on MACH_JZ4780, that means it can be
enabled only if we're building a kernel specially crafted for a
JZ4780-based board, while most GNU/Linux distributions will want one
generic MIPS kernel that works on multiple boards.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ae00833e3 ]
This is needed to make the display and venc work properly.
Compare to omap3-beagle.dts.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
