[ Upstream commit 9de30f3f7f ]
In copy_result_to_user(), we first create a struct dlm_lock_result, which
contains a struct dlm_lksb, the last member of which is a pointer to the
lvb. Unfortunately, we copy the entire struct dlm_lksb to the result
struct, which is then copied to userspace at the end of the function,
leaking the contents of sb_lvbptr, which is a valid kernel pointer in some
cases (indeed, later in the same function the data it points to is copied
to userspace).
It is an error to leak kernel pointers to userspace, as it undermines KASLR
protections (see e.g. 65eea8edc3 ("floppy: Do not copy a kernel pointer to
user memory in FDGETPRM ioctl") for another example of this).
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d968b4e240 ]
dlm_config_nodes() does not allocate nodes on failure, so we should not
free() nodes when it fails.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 157c0f2f64 ]
During the initial connect to a non-pd port, sink would hard reset
twice before deeming that the port partner is non-pd. TCPM sets the
the charge path to false during the hard reset. This causes unnecessary
connects/disconnects of charge path and makes port take longer to
charge from the non-pd ports. Avoid this by not setting the charge path
to false unless the partner has already identified to be pd capable.
When partner is a pd port, set the charge path to false in
SNK_HARD_RESET_SINK_OFF. Set the current limits to default value based
of CC pull up and resume the charge path when port enters
SNK_HARD_RESET_SINK_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--------
Changes in V3:
Rebase on top of usb-next
Changes in V2:
Based on feedback of jackp@codeaurora.org
- vsafe_5v_hard_reset flag from tcpc_config is removed
- Patch only differentiates between pd port partner and non-pd port
partner
V1 version of the patch is here:
https://lkml.org/lkml/2018/9/14/11
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d83ca3ea83 ]
An address change for a remote port cause PRLI for the wrong protocol
to be sent. The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.
Fix the copy logic for the address change. Beefed up log messages in
this area as well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d496b9a724 ]
Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.
Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.
While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 036cad1f1a ]
On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.
Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9155cf30a3 ]
In megasas_transition_to_ready() driver waits 180seconds for controller to
change FW state. Here we are calling msleep(1) in a loop for this. As
explained in timers-howto.txt, msleep(1) will actually sleep longer than
1ms. If a faulty controller is connected, we will end up waiting for much
more than 180 seconds causing unnecessary delays during load.
Change the granularity of msleep() call from 1ms to 1000ms.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97f3519409 ]
Currently driver is modifying both current & NVRAM/persistent data in
Manufacturing page11. Driver should change only current copy of
Manufacturing page11. It should not modify the persistent data.
So removed the section of code where driver is modifying the persistent
data of Manufacturing page11.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9029a72500 ]
This is to fix SYNC CACHE and START STOP command failures with
DID_NO_CONNECT during driver unload.
In driver's IO submission patch (i.e. in driver's .queuecommand()) driver
won't allow any SCSI commands to the IOC when ioc->remove_host flag is set
and hence SYNC CACHE commands which are issued to the target drives (where
write cache is enabled) during driver unload time is failed with
DID_NO_CONNECT status.
Now modified the driver to allow SYNC CACHE and START STOP commands to IOC,
even when remove_host flag is set.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c04a17d2a9 ]
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d39e1bb1c ]
It looks like we wanted to print a maximum of BSSList_rid.ssidLen bytes
of the ssid, but we accidentally use "%*s" (width) instead of "%.*s"
(precision) so if the ssid doesn't have a NUL terminator this could lead
to an overflow.
Static analysis. Not tested.
Fixes: e174961ca1 ("net: convert print_mac to %pM")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96fca788e5 ]
This message greatly spams the log under heavy Tx of frames with BK access
class which is especially true when operating as AP. It is also not informative
as the "agg'ablity" of TIDs are set once and never change.
Fix this by logging only in debug mode.
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 307b00c5e6 ]
Add missing break statement in order to prevent the code from falling
through to the default case.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3419348a97 ]
We return 0 unconditionally at the end of
'wlcore_vendor_cmd_smart_config_start()'.
However, 'ret' is set to some error codes in several error handling paths
and we already return some error codes at the beginning of the function.
Return 'ret' instead to propagate the error code.
Fixes: 80ff8063e8 ("wlcore: handle smart config vendor commands")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82e60d920e ]
Similar to regulator error handling, we should only start tearing down
the 'i - 1' clock when clock 'i' fails to enable. Otherwise, we might
end up with an unbalanced clock, where we never successfully enabled the
clock, but we try to disable it anyway.
Fixes: a6a793f987 ("ath10k: vote for hardware resources for WCN3990")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c69709f8e ]
RGF_CAF_ICR register location has changed in Talyn-MB.
Add RGF_CAF_ICR_TALYN_MB to support the new address.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04de15010a ]
L2 RX status errors should not be treated as a bitmap and the actual
error values should be checked.
Print L2 errors as wil_err_ratelimited for easier debugging
when such errors occurs.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84ec040d0f ]
All wil6210 device memory access should be 4 bytes aligned. In io
blob wil6210 did not force alignment for read function, this caused
alignment fault on some platforms.
Fixing that by accessing all 4 lower bytes and return to host the
requested data.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e17916b35 ]
Note: this patch fixes a problem in a feature outside of btrfs ("kernel
hacking: add a config option to disable compiler auto-inlining") and is
applied ahead of time due to cross-subsystem dependencies.
On 32-bit ARM with gcc-8, I see a link error with the addition of the
CONFIG_NO_AUTO_INLINE option:
fs/btrfs/super.o: In function `btrfs_statfs':
super.c:(.text+0x67b8): undefined reference to `__aeabi_uldivmod'
super.c:(.text+0x67fc): undefined reference to `__aeabi_uldivmod'
super.c:(.text+0x6858): undefined reference to `__aeabi_uldivmod'
super.c:(.text+0x6920): undefined reference to `__aeabi_uldivmod'
super.c:(.text+0x693c): undefined reference to `__aeabi_uldivmod'
fs/btrfs/super.o:super.c:(.text+0x6958): more undefined references to `__aeabi_uldivmod' follow
So far this is the only file that shows the behavior, so I'd propose
to just work around it by marking the functions as 'static inline'
that normally get inlined here.
The reference to __aeabi_uldivmod comes from a div_u64() which has an
optimization for a constant division that uses a straight '/' operator
when the result should be known to the compiler. My interpretation is
that as we turn off inlining, gcc still expects the result to be constant
but fails to use that constant value.
Link: https://lkml.kernel.org/r/20181103153941.1881966-1-arnd@arndb.de
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[ add the note ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97adaddaa6 ]
When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.
test config:
CONFIG_BPFILTER=y
# CONFIG_BPFILTER_UMH is not set
test command:
%iptables -L
iptables: No chain/target/match by that name.
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea956d8be9 ]
Empty executable arguments were being skipped when printing out the list
of arguments in an EXECVE record, making it appear they were somehow
lost. Include empty arguments as an itemized empty string.
Reproducer:
autrace /bin/ls "" "/etc"
ausearch --start recent -m execve -i | grep EXECVE
type=EXECVE msg=audit(10/03/2018 13:04:03.208:1391) : argc=3 a0=/bin/ls a2=/etc
With fix:
type=EXECVE msg=audit(10/03/2018 21:51:38.290:194) : argc=3 a0=/bin/ls a1= a2=/etc
type=EXECVE msg=audit(1538617898.290:194): argc=3 a0="/bin/ls" a1="" a2="/etc"
Passes audit-testsuite. GH issue tracker at
https://github.com/linux-audit/audit-kernel/issues/99
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: cleaned up the commit metadata]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb14ada11d ]
When the kernel is built with CONFIG_THUMB2_KERNEL we would set the
kernel's resume entry point to be a function that is already built as
Thumb-2 code while the boot agent doing the resume is in ARM mode, so
this does not work. There is a header label defined: cpu_resume_arm
which we can use to do the switching for us.
Fixes: 0b741b8234 ("soc: bcm: brcmstb: Add support for S2/S3/S5 suspend states (ARM)")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 859783d139 ]
In the user manual of A64 SoC, the bit 22 and 23 of pll-mipi control
register is called "LDO{1,2}_EN", and according to the BSP source code
from Allwinner , the LDOs are enabled during the clock's enabling
process.
The clock failed to generate output if the two LDOs are not enabled.
Add the two bits to the clock's gate bits, so that the LDOs are enabled
when the PLL is enabled.
Fixes: c6a0637460 ("clk: sunxi-ng: Add A64 clocks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ad9fb750a ]
Bindings for "fixed-regulator" only explicitly support "gpio" property,
not "gpios". Fix by correcting the property name.
The enet PHYs on imx6sx-sdb needs to be explicitly reset after a power
cycle, this can be handled by the phy-reset-gpios property. Sadly this
is not handled on suspend: the fec driver turns phy-supply off but
doesn't assert phy-reset-gpios again on resume.
Since additional phy-level work is required to support powering off the
phy in suspend fix the problem by just marking the regulator as
"boot-on" "always-on" so that it's never turned off. This behavior is
equivalent to older releases.
Keep the phy-reset-gpios property on fec anyway because it is a correct
description of board design.
This issue was exposed by commit efdfeb079c ("regulator: fixed:
Convert to use GPIO descriptor only") which causes the "gpios" property
to also be parsed. Before that commit the "gpios" property had no
effect, PHY reset was only handled in the the bootloader.
This fixes linux-next boot failures previously reported here:
https://lore.kernel.org/patchwork/patch/982437/#1177900https://lore.kernel.org/patchwork/patch/994091/#1178304
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a277d516de ]
When CONFIG_CC_OPTIMIZE_FOR_DEBUGGING is enabled, the compiler
fails to optimize out a dead code path, which leads to a link failure:
net/openvswitch/conntrack.o: In function `ovs_ct_set_labels':
conntrack.c:(.text+0x2e60): undefined reference to `nf_connlabels_replace'
In this configuration, we can take a shortcut, and completely
remove the contrack label code. This may also help the regular
optimization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f130a37c4 ]
When load_balance() fails to move some load because of task affinity,
we end up increasing sd->balance_interval to delay the next periodic
balance in the hopes that next time we look, that annoying pinned
task(s) will be gone.
However, idle_balance() pays no attention to sd->balance_interval, yet
it will still lead to an increase in balance_interval in case of
pinned tasks.
If we're going through several newidle balances (e.g. we have a
periodic task), this can lead to a huge increase of the
balance_interval in a very small amount of time.
To prevent that, don't increase the balance interval when going
through a newidle balance.
This is a similar approach to what is done in commit 58b26c4c02
("sched: Increment cache_nice_tries only on periodic lb"), where we
disregard newidle balance and rely on periodic balance for more stable
results.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Dietmar.Eggemann@arm.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: patrick.bellasi@arm.com
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/1537974727-30788-2-git-send-email-valentin.schneider@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe60faa506 ]
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.
Problem is that GSO packets can end up comsuming more than
the BQL budget.
Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.
It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.
It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.
Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e98578775 ]
When -EIOCBQUEUED returns, it means that aio_complete() will be called
from dio_complete(), which is an asynchronous progress against
write_iter. Generally, IO is a very slow progress than executing
instruction, but we still can't take the risk to access a freed iocb.
And we do face a BUG crash issue. Using the crash tool, iocb is
obviously freed already.
crash> struct -x kiocb ffff881a350f5900
struct kiocb {
ki_filp = 0xffff881a350f5a80,
ki_pos = 0x0,
ki_complete = 0x0,
private = 0x0,
ki_flags = 0x0
}
And the backtrace shows:
ocfs2_file_write_iter+0xcaa/0xd00 [ocfs2]
aio_run_iocb+0x229/0x2f0
do_io_submit+0x291/0x540
SyS_io_submit+0x10/0x20
system_call_fastpath+0x16/0x75
Link: http://lkml.kernel.org/r/1523361653-14439-1-git-send-email-ge.changwei@h3c.com
Signed-off-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e68599a3c3 ]
Mike Galbraith reported a regression caused by the commit 9b6f7e163c
("mm: rework memcg kernel stack accounting") on a system with
"cgroup_disable=memory" boot option: the system panics with the following
stack trace:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000f8
PGD 0 P4D 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 0 PID: 1 Comm: systemd Not tainted 4.19.0-preempt+ #410
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20180531_142017-buildhw-08.phx2.fed4
RIP: 0010:page_counter_try_charge+0x22/0xc0
Code: 41 5d c3 c3 0f 1f 40 00 0f 1f 44 00 00 48 85 ff 0f 84 a7 00 00 00 41 56 48 89 f8 49 89 fe 49
Call Trace:
try_charge+0xcb/0x780
memcg_kmem_charge_memcg+0x28/0x80
memcg_kmem_charge+0x8b/0x1d0
copy_process.part.41+0x1ca/0x2070
_do_fork+0xd7/0x3d0
do_syscall_64+0x5a/0x180
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The problem occurs because get_mem_cgroup_from_current() returns the NULL
pointer if memory controller is disabled. Let's check if this is a case
at the beginning of memcg_kmem_charge() and just return 0 if
mem_cgroup_disabled() returns true. This is how we handle this case in
many other places in the memory controller code.
Link: http://lkml.kernel.org/r/20181029215123.17830-1-guro@fb.com
Fixes: 9b6f7e163c ("mm: rework memcg kernel stack accounting")
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Acked-by: Rik van Riel <riel@surriel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3404155190 ]
turbostat recently gained a feature adding APIC and X2APIC columns.
While they are disabled by-default, they are enabled with --debug
or when explicitly requested, eg.
$ sudo turbostat --quiet --show Package,Node,Core,CPU,APIC,X2APIC date
But these columns erroneously showed zeros on AMD hardware.
This patch corrects the APIC and X2APIC [sic] columns on AMD.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98356eb0ae ]
After 'a66649dab350 arm64: fix vdso-offsets.h dependency' if
one will try to build .i file in case of external kernel module,
build fails complaining that prepare0 target is missing. This
issue came up with SystemTap when it tries to build variety
of .i files for its own generated kernel modules trying to
figure given kernel features/capabilities.
The issue is that prepare0 is defined in top level Makefile
only if KBUILD_EXTMOD is not defined. .i file rule depends
on prepare and in case KBUILD_EXTMOD defined top level Makefile
contains empty rule for prepare. But after mentioned commit
arch/arm64/Makefile would introduce dependency on prepare0
through its own prepare target.
Fix it to put proper ifdef KBUILD_EXTMOD around code introduced
by mentioned commit. It matches what top level Makefile does.
Acked-by: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Victor Kamensky <kamensky@cisco.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe5c59ff6 ]
The nvme pci driver had been adding its CMB resource to the P2P DMA
subsystem everytime on on a controller reset. This results in the
following warning:
------------[ cut here ]------------
nvme 0000:00:03.0: Conflicting mapping in same section
WARNING: CPU: 7 PID: 81 at kernel/memremap.c:155 devm_memremap_pages+0xa6/0x380
...
Call Trace:
pci_p2pdma_add_resource+0x153/0x370
nvme_reset_work+0x28c/0x17b1 [nvme]
? add_timer+0x107/0x1e0
? dequeue_entity+0x81/0x660
? dequeue_entity+0x3b0/0x660
? pick_next_task_fair+0xaf/0x610
? __switch_to+0xbc/0x410
process_one_work+0x1cf/0x350
worker_thread+0x215/0x3d0
? process_one_work+0x350/0x350
kthread+0x107/0x120
? kthread_park+0x80/0x80
ret_from_fork+0x1f/0x30
---[ end trace f7ea76ac6ee72727 ]---
nvme nvme0: failed to register the CMB
This patch fixes this by registering the CMB with P2P only once.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7756e2b5d6 ]
ndev_vec_mask() should be returning u64 mask value instead of int.
Otherwise the mask value returned can be incorrect for larger
vectors.
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Lucas Van <lucas.van@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a861594b1b ]
The tx_time should be in usecs (according to the comment above the
variable), but the setting of the timer during the rearming is done in
msecs. Change it to match the expected units.
Fixes: e74bfeedad ("NTB: Add flow control to the ntb_netdev")
Suggested-by: Gerd W. Haeussler <gerd.haeussler@cesys-it.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c12493809 ]
When there is a PHY, the driver needs to complete some operations through
MDIO during reset reinitialization, so HCLGE_STATE_CMD_DISABLE is more
suitable than HCLGE_STATE_RST_HANDLING to prevent the MDIO operation from
being sent during the hardware reset.
Fixes: b50ae26c57 ("net: hns3: never send command queue message to IMP when reset)
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d71ec6cbf ]
The HEAD pointer of the hardware command queue maybe equal to the command
queue's next_to_use in the driver, so that does not belong to the invalid
HEAD pointer, since the hardware may not process the command in time,
causing the HEAD pointer to be too late to update. The variables' name
in this function is unreadable, so give them a more readable one.
Fixes: 3ff504908f ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4411408a ]
The current driver supports handling two vector0 interrupts, reset and
mailbox. When the hardware reports an interrupt of another type of
interrupt source, if the driver does not process the interrupt, but
enables the interrupt, the hardware will repeatedly report the unknown
interrupt.
Therefore, the driver enables the vector0 interrupt after clearing the
known type of interrupt source. Other conditions are not enabled.
Fixes: cd8c5c269b ("net: hns3: Fix for hclge_reset running repeatly problem")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b907a083 ]
When hns3_get_ring_config()/hns3_queue_to_ring()/
hns3_get_vector_ring_chain() failed during resetting, the allocated
memory has not been freed before these three functions return. So
this patch adds error handler in these functions to fix it.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
