[ Upstream commit 03e2c9c782 ]
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820830ec91 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e4209b380 ]
The current implementation of scsi_vpd_lun_id() uses the designator length
as an implicit measure of priority. This works most of the time, but not
always. For example, some Hitachi storage arrays return this in VPD 0x83:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: T10 vendor identification, code_set: ASCII
associated with the Addressed logical unit
vendor id: HITACHI
vendor specific: 5030C3502025
Designation descriptor number 2, descriptor length: 6
designator_type: vendor specific [0x0], code_set: Binary
associated with the Target port
vendor specific: 08 03
Designation descriptor number 3, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the Addressed logical unit
NAA 6, IEEE Company_id: 0x60e8
Vendor Specific Identifier: 0x7c35000
Vendor Specific Identifier Extension: 0x30c35000002025
[0x60060e8007c350000030c35000002025]
The current code would use the first descriptor because it's longer than
the NAA descriptor. But this is wrong, the kernel is supposed to prefer NAA
descriptors over T10 vendor ID. Designator length should only be used to
compare designators of the same type.
This patch addresses the issue by separating designator priority and
length.
Link: https://lore.kernel.org/r/20201029170846.14786-1-mwilck@suse.com
Fixes: 9983bed390 ("scsi: Add scsi_vpd_lun_id()")
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 299fe9937d ]
When compiled with CONFIG_HAVE_CLK, the kernel need to get provider for the
clock API. This is usually selected by the platform and the sound drivers
should not really care about this. However COMPILE_TEST is special and the
platform required may not have been selected, leading to this type of
error:
> aiu-encoder-spdif.c:(.text+0x3a0): undefined reference to `clk_set_parent'
Since we need a sane provider of the API with COMPILE_TEST, depends on
COMMON_CLK.
Fixes: 6dc4fa179f ("ASoC: meson: add axg fifo base driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201116172423.546855-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27c3943683 ]
mtk_vcodec_release_dec_pm() will be called in two places:
a. mtk_vcodec_init_dec_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_dec_remove().
In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_dec_pm() previously.
Thus add put_devices() call in mtk_vcodec_release_dec_pm()
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a08ad6339e ]
The are two instances of sizeof() being used incorrectly. The
sizeof(void *) is incorrect because urb_buffer is a char ** pointer,
fix this by using sizeof(*dev->urb_buffer). The sizeof(dma_addr_t *)
is incorrect, it should be sizeof(*dev->urb_dma), which is a dma_addr_t
and not a dma_addr_t *. This errors did not cause any issues because
it just so happens the sizes are the same.
Addresses-Coverity: ("Sizeof not portable (SIZEOF_MISMATCH)")
Fixes: 16427faf28 ("[media] tm6000: Add parameter to keep urb bufs allocated")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b5c130fb2 ]
The return value of qat_hal_rd_ae_csr() is always a CSR value and never
a status and should not be stored in the status variable of
qat_hal_put_rel_rd_xfer().
This removes the assignment as qat_hal_rd_ae_csr() is not expected to
fail.
A more comprehensive handling of the theoretical corner case which could
result in a fail will be submitted in a separate patch.
Fixes: 8c9478a400 ("crypto: qat - reduce stack size with KASAN")
Signed-off-by: Jack Xu <jack.xu@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Fiona Trahe <fiona.trahe@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a5fe2fb96 ]
When BCM47XX_BCMA is enabled and BCMA_DRIVER_PCI is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for BCMA_DRIVER_PCI_HOSTMODE
Depends on [n]: MIPS [=y] && BCMA_DRIVER_PCI [=n] && PCI_DRIVERS_LEGACY [=y] && BCMA [=y]=y
Selected by [y]:
- BCM47XX_BCMA [=y] && BCM47XX [=y] && PCI [=y]
The reason is that BCM47XX_BCMA selects BCMA_DRIVER_PCI_HOSTMODE without
depending on or selecting BCMA_DRIVER_PCI while BCMA_DRIVER_PCI_HOSTMODE
depends on BCMA_DRIVER_PCI. This can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: c1d1c5d421 ("bcm47xx: add support for bcma bus")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209879
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb7dc5db6 ]
gcc points out a suspicious mixing of enum types in a function that
converts from MTHCA_OPCODE_* values to IB_WC_* values:
drivers/infiniband/hw/mthca/mthca_cq.c: In function 'mthca_poll_one':
drivers/infiniband/hw/mthca/mthca_cq.c:607:21: warning: implicit conversion from 'enum <anonymous>' to 'enum ib_wc_opcode' [-Wenum-conversion]
607 | entry->opcode = MTHCA_OPCODE_INVALID;
Nothing seems to ever check for MTHCA_OPCODE_INVALID again, no idea if
this is meaningful, but it seems harmless as it deals with an invalid
input.
Remove MTHCA_OPCODE_INVALID and set the ib_wc_opcode to 0xFF, which is
still bogus, but at least doesn't make compiler warnings.
Fixes: 2a4443a699 ("[PATCH] IB/mthca: fill in opcode field for send completions")
Link: https://lore.kernel.org/r/20201026211311.3887003-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58cfa49c2b ]
In comment 173ca26e9b ("samples/bpf: add comprehensive ipip, ipip6,
ip6ip6 test") we added ip6ip6 test for bpf tunnel testing. But in commit
933a741e3b ("selftests/bpf: bpf tunnel test.") when we moved it to
the current folder, we didn't add it.
This patch add the ip6ip6 test back to bpf tunnel test. Update the ipip6's
topology for both IPv4 and IPv6 testing. Since iperf test is removed as
currect framework simplified it in purpose, I also removed unused tcp
checkings in test_tunnel_kern.c.
Fixes: 933a741e3b ("selftests/bpf: bpf tunnel test.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20201110015013.1570716-2-liuhangbin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dfccd13db ]
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928b ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca6 ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73bc7510ea ]
Exynos7 uses the same syscon reboot and poweroff nodes as other Exynos
SoCs, so instead of duplicating code we can just include common dtsi
file, which already contains definitions of them. After this change,
poweroff node will be also available, previously this dts file did
contain only reboot node.
Fixes: fb026cb652 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc93 ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-1-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 200ea5a229 ]
A previous fix, commit 83370b31a9 ("selinux: fix error initialization
in inode_doinit_with_dentry()"), changed how failures were handled
before a SELinux policy was loaded. Unfortunately that patch was
potentially problematic for two reasons: it set the isec->initialized
state without holding a lock, and it didn't set the inode's SELinux
label to the "default" for the particular filesystem. The later can
be a problem if/when a later attempt to revalidate the inode fails
and SELinux reverts to the existing inode label.
This patch should restore the default inode labeling that existed
before the original fix, without affecting the LABEL_INVALID marking
such that revalidation will still be attempted in the future.
Fixes: 83370b31a9 ("selinux: fix error initialization in inode_doinit_with_dentry()")
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c22b80f61 ]
soc-pcm's dpcm_fe_dai_do_trigger() supported DRAIN commnad up to kernel
v5.4 where explicit switch(cmd) has been introduced which takes into
account all SNDRV_PCM_TRIGGER_xxx but SNDRV_PCM_TRIGGER_DRAIN. Update
switch statement to reactive support for it.
As DRAIN is somewhat unique by lacking negative/stop counterpart, bring
behaviour of dpcm_fe_dai_do_trigger() for said command back to its
pre-v5.4 state by adding it to START/RESUME/PAUSE_RELEASE group.
Fixes: acbf27746e ("ASoC: pcm: update FE/BE trigger order based on the command")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201026100129.8216-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4ccc37693 ]
PHY disable/enable resets PLL registers to default values. Thus in
addition to restoring several registers we also need to restore VCO rate
settings.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c6659785df ("drm/msm/dsi/pll: call vco set rate explicitly")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3acc4522d8 ]
When running fault injection test, if we don't stop checkpoint, some stale
NAT entries were flushed which breaks consistency.
Fixes: 86f33603f8 ("f2fs: handle errors of f2fs_get_meta_page_nofail")
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c0b976bf2 ]
Currently in generic_secondary_smp_init(), cur_cpu_spec->cpu_restore()
is called before a stack has been set up in r1. This was previously fine
as the cpu_restore() functions were implemented in assembly and did not
use a stack. However commit 5a61ef74f2 ("powerpc/64s: Support new
device tree binding for discovering CPU features") used
__restore_cpu_cpufeatures() as the cpu_restore() function for a
device-tree features based cputable entry. This is a C function and
hence uses a stack in r1.
generic_secondary_smp_init() is entered on the secondary cpus via the
primary cpu using the OPAL call opal_start_cpu(). In OPAL, each hardware
thread has its own stack. The OPAL call is ran in the primary's hardware
thread. During the call, a job is scheduled on a secondary cpu that will
start executing at the address of generic_secondary_smp_init(). Hence
the value that will be left in r1 when the secondary cpu enters the
kernel is part of that secondary cpu's individual OPAL stack. This means
that __restore_cpu_cpufeatures() will write to that OPAL stack. This is
not horribly bad as each hardware thread has its own stack and the call
that enters the kernel from OPAL never returns, but it is still wrong
and should be corrected.
Create the temp kernel stack before calling cpu_restore().
As noted by mpe, for a kexec boot, the secondary CPUs are released from
the spin loop at address 0x60 by smp_release_cpus() and then jump to
generic_secondary_smp_init(). The call to smp_release_cpus() is in
setup_arch(), and it comes before the call to emergency_stack_init().
emergency_stack_init() allocates an emergency stack in the PACA for each
CPU. This address in the PACA is what is used to set up the temp kernel
stack in generic_secondary_smp_init(). Move releasing the secondary CPUs
to after the PACAs have been allocated an emergency stack, otherwise the
PACA stack pointer will contain garbage and hence the temp kernel stack
created from it will be broken.
Fixes: 5a61ef74f2 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201014072837.24539-1-jniethe5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbb60031dd ]
gcc -Wextra warns about a function taking an enum argument
being called with a bool:
drivers/gpu/drm/amd/amdgpu/../display/modules/color/color_gamma.c: In function 'apply_degamma_for_user_regamma':
drivers/gpu/drm/amd/amdgpu/../display/modules/color/color_gamma.c:1617:29: warning: implicit conversion from 'enum <anonymous>' to 'enum dc_transfer_func_predefined' [-Wenum-conversion]
1617 | build_coefficients(&coeff, true);
It appears that a patch was added using the old calling conventions
after the type was changed, and the value should actually be 0
(TRANSFER_FUNCTION_SRGB) here instead of 1 (true).
Fixes: 55a01d4023 ("drm/amd/display: Add user_regamma to color module")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93c0210671 ]
Left and Right justified mode are computed using the same formula
as DSP_A and DSP_B mode.
Which is wrong and the user manual explicitly says:
LRCK_PERDIOD:
PCM Mode: Number of BCLKs within (Left + Right) channel width.
I2S/Left-Justified/Right-Justified Mode: Number of BCLKs within each
individual channel width(Left or Right)
Fix this by using the same formula as the I2S mode.
Fixes: 7ae7834ec4 ("ASoC: sun4i-i2s: Add support for DSP formats")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201030144648.397824-2-peron.clem@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c98e233062 ]
An incorrect sizeof() is being used, sizeof(priv->ring[i].rdr_req) is
not correct, it should be sizeof(*priv->ring[i].rdr_req). Note that
since the size of ** is the same size as * this is not causing any
issues.
Addresses-Coverity: ("Sizeof not portable (SIZEOF_MISMATCH)")
Fixes: 9744fec95f ("crypto: inside-secure - remove request list to improve performance")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0237616173 ]
current_desc_hdr() returns a u32 but in fact this is a __be32,
leading to a lot of sparse warnings.
Change the return type to __be32 and ensure it is handled as
sure by the caller.
Fixes: 3e721aeb3d ("crypto: talitos - handle descriptor not found in error path")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 195404db27 ]
current_desc_hdr() compares the value of the current descriptor
with the next_desc member of the talitos_desc struct.
While the current descriptor is obtained from in_be32() which
return CPU ordered bytes, next_desc member is in big endian order.
Convert the current descriptor into big endian before comparing it
with next_desc.
This fixes a sparse warning.
Fixes: 37b5e8897e ("crypto: talitos - chain in buffered data for ahash on SEC1")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a110f3750b ]
core_link_write_dpcd() returns enum dc_status, not ddc_result:
display/dc/core/dc_link_dp.c: In function 'dp_set_panel_mode':
display/dc/core/dc_link_dp.c:4237:11: warning: implicit conversion from 'enum dc_status' to 'enum ddc_result'
[-Wenum-conversion]
Avoid the warning by using the correct enum in the caller.
Fixes: 0b22632243 ("drm/amd/display: Synchronous DisplayPort Link Training")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
