commit a019b36123 upstream.
On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc()
allocation as done for the firmware tracer will always fail.
Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself
that copies the debug data into the trace array and there is no need for
the allocation to be contiguous in physical memory. We can therefor use
kvzalloc() instead of kzalloc() and get rid of the large contiguous
allcoation.
Fixes: f53aaa31cc ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc23d0e3f7 upstream.
When the kernel is built with CONFIG_DEBUG_PER_CPU_MAPS, the cpumap code
can trigger a spurious warning if CONFIG_CPUMASK_OFFSTACK is also set. This
happens because in this configuration, NR_CPUS can be larger than
nr_cpumask_bits, so the initial check in cpu_map_alloc() is not sufficient
to guard against hitting the warning in cpumask_check().
Fix this by explicitly checking the supplied key against the
nr_cpumask_bits variable before calling cpu_possible().
Fixes: 6710e11269 ("bpf: introduce new bpf cpu map type BPF_MAP_TYPE_CPUMAP")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Xiumei Mu <xmu@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200416083120.453718-1-toke@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90444b9584 upstream.
Since its inception the module was meant to be disabled by default, but
the original commit failed to add the relevant property.
Fixes: 4aba4cf820 ("ARM: dts: bcm2835: Add the DSI module nodes and clocks")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a8f41023e upstream.
Some Google Apex Edge TPU devices have a class code of 0
(PCI_CLASS_NOT_DEFINED). This prevents the PCI core from assigning
resources for the Apex BARs because __dev_sort_resources() ignores
classless devices, host bridges, and IOAPICs.
On x86, firmware typically assigns those resources, so this was not a
problem. But on some architectures, firmware does *not* assign BARs, and
since the PCI core didn't do it either, the Apex device didn't work
correctly:
apex 0000:01:00.0: can't enable device: BAR 0 [mem 0x00000000-0x00003fff 64bit pref] not claimed
apex 0000:01:00.0: error enabling PCI device
f390d08d8b ("staging: gasket: apex: fixup undefined PCI class") added a
quirk to fix the class code, but it was in the apex driver, and if the
driver was built as a module, it was too late to help.
Move the quirk to the PCI core, where it will always run early enough that
the PCI core will assign resources if necessary.
Link: https://lore.kernel.org/r/CAEzXK1r0Er039iERnc2KJ4jn7ySNUOG9H=Ha8TD8XroVqiZjgg@mail.gmail.com
Fixes: f390d08d8b ("staging: gasket: apex: fixup undefined PCI class")
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Debugged-by: Luís Mendes <luis.p.mendes@gmail.com>
Tested-by: Luis Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2880325bda upstream.
The ASMedia USB XHCI Controller claims to support generating PME# while
in D0:
01:00.0 USB controller: ASMedia Technology Inc. Device 2142 (prog-if 30 [XHCI])
Subsystem: SUNIX Co., Ltd. Device 312b
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
However PME# only gets asserted when plugging USB 2.0 or USB 1.1 devices,
but not for USB 3.0 devices.
Remove PCI_PM_CAP_PME_D0 to avoid using PME under D0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205919
Link: https://lore.kernel.org/r/20191219192006.16270-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23cf1ee1f1 upstream.
Utilize the xpo_release_rqst transport method to ensure that each
rqstp's svc_rdma_recv_ctxt object is released even when the server
cannot return a Reply for that rqstp.
Without this fix, each RPC whose Reply cannot be sent leaks one
svc_rdma_recv_ctxt. This is a 2.5KB structure, a 4KB DMA-mapped
Receive buffer, and any pages that might be part of the Reply
message.
The leak is infrequent unless the network fabric is unreliable or
Kerberos is in use, as GSS sequence window overruns, which result
in connection loss, are more common on fast transports.
Fixes: 3a88092ee3 ("svcrdma: Preserve Receive buffer until svc_rdma_sendto")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b674b9ac8 upstream.
The filesystem freeze sequence in XFS waits on any background
eofblocks or cowblocks scans to complete before the filesystem is
quiesced. At this point, the freezer has already stopped the
transaction subsystem, however, which means a truncate or cowblock
cancellation in progress is likely blocked in transaction
allocation. This results in a deadlock between freeze and the
associated scanner.
Fix this problem by holding superblock write protection across calls
into the block reapers. Since protection for background scans is
acquired from the workqueue task context, trylock to avoid a similar
deadlock between freeze and blocking on the write lock.
Fixes: d6b636ebb1 ("xfs: halt auto-reclamation activities while rebuilding rmap")
Reported-by: Paul Furtado <paulfurtado91@gmail.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Chandan Rajendra <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c799fca8ba upstream.
Positive return values are also failures that don't set val,
although this probably can't happen. Fixes gcc 10 warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
3747 | *phy_fw_ver = val;
Fixes: 01b6961410 ("cxgb4: Add PHY firmware support for T420-BT cards")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e631eee17 upstream.
Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6
socket as well as UDPv6 when trying to transmit fragmentably.
Without this, packets filled to the normal size used by the kernel AFS
client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE
immediately. The ->sk_error_report() notification hook is called, but
rxrpc doesn't generate a trace for it.
This is a temporary fix; a more permanent solution needs to involve
changing the size of the packets being filled in accordance with the MTU,
which isn't currently done in AF_RXRPC. The reason for not doing so was
that, barring the last packet in an rx jumbo packet, jumbos can only be
assembled out of 1412-byte packets - and the plan was to construct jumbos
on the fly at transmission time.
Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to
engage in this anyway since fragmentation is only done by the sender. We
can then condense the switch-statement in rxrpc_send_data_packet().
Fixes: 75b54cb57c ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1e8399eee upstream.
New struct nfsd4_blocked_lock allocated in find_or_allocate_block()
does not initialized nbl_list and nbl_lru.
If conflock allocation fails rollback can call list_del_init()
access uninitialized fields and corrupt memory.
v2: just initialize nbl_list and nbl_lru right after nbl allocation.
Fixes: 76d348fadf ("nfsd: have nfsd4_lock use blocking locks for v4.1+ lock")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9df8ba7c63 upstream.
If probe fails after enabling the regulators regulator_put is called for
each supply without having them disabled before. This produces some
warnings like
WARNING: CPU: 0 PID: 90 at drivers/regulator/core.c:2044 _regulator_put.part.0+0x154/0x15c
[<c010f7a8>] (unwind_backtrace) from [<c010c544>] (show_stack+0x10/0x14)
[<c010c544>] (show_stack) from [<c012b640>] (__warn+0xd0/0xf4)
[<c012b640>] (__warn) from [<c012b9b4>] (warn_slowpath_fmt+0x64/0xc4)
[<c012b9b4>] (warn_slowpath_fmt) from [<c04c4064>] (_regulator_put.part.0+0x154/0x15c)
[<c04c4064>] (_regulator_put.part.0) from [<c04c4094>] (regulator_put+0x28/0x38)
[<c04c4094>] (regulator_put) from [<c04c40cc>] (regulator_bulk_free+0x28/0x38)
[<c04c40cc>] (regulator_bulk_free) from [<c0579b2c>] (release_nodes+0x1d0/0x22c)
[<c0579b2c>] (release_nodes) from [<c05756dc>] (really_probe+0x108/0x34c)
[<c05756dc>] (really_probe) from [<c0575aec>] (driver_probe_device+0xb8/0x16c)
[<c0575aec>] (driver_probe_device) from [<c0575d40>] (device_driver_attach+0x58/0x60)
[<c0575d40>] (device_driver_attach) from [<c0575da0>] (__driver_attach+0x58/0xcc)
[<c0575da0>] (__driver_attach) from [<c0573978>] (bus_for_each_dev+0x78/0xc0)
[<c0573978>] (bus_for_each_dev) from [<c0574b5c>] (bus_add_driver+0x188/0x1e0)
[<c0574b5c>] (bus_add_driver) from [<c05768b0>] (driver_register+0x74/0x108)
[<c05768b0>] (driver_register) from [<c061ab7c>] (i2c_register_driver+0x3c/0x88)
[<c061ab7c>] (i2c_register_driver) from [<c0102df8>] (do_one_initcall+0x58/0x250)
[<c0102df8>] (do_one_initcall) from [<c01a91bc>] (do_init_module+0x60/0x244)
[<c01a91bc>] (do_init_module) from [<c01ab5a4>] (load_module+0x2180/0x2540)
[<c01ab5a4>] (load_module) from [<c01abbd4>] (sys_finit_module+0xd0/0xe8)
[<c01abbd4>] (sys_finit_module) from [<c01011e0>] (__sys_trace_return+0x0/0x20)
Fixes: 3fd6e7d9a1 (ASoC: tas571x: New driver for TI TAS571x power amplifiers)
Signed-off-by: Philipp Puschmann <p.puschmann@pironex.de>
Link: https://lore.kernel.org/r/20200414112754.3365406-1-p.puschmann@pironex.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c824ec094 upstream.
For some reason, the MI2S DAIs do not have channels_min/max defined.
This means that snd_soc_dai_stream_valid() returns false,
i.e. the DAIs have neither valid playback nor capture stream.
It's quite surprising that this ever worked correctly,
but in 5.7-rc1 this is now failing badly: :)
Commit 0e9cf4c452 ("ASoC: pcm: check if cpu-dai supports a given stream")
introduced a check for snd_soc_dai_stream_valid() before calling
hw_params(), which means that the q6i2s_hw_params() function
was never called, eventually resulting in:
qcom-q6afe aprsvc:q6afe:4:4: no line is assigned
... even though "qcom,sd-lines" is set in the device tree.
Commit 9b5db05936 ("ASoC: soc-pcm: dpcm: Only allow playback/capture if supported")
now even avoids creating PCM devices if the stream is not supported,
which means that it is failing even earlier with e.g.:
Primary MI2S: ASoC: no backend playback stream
Avoid all that trouble by adding channels_min/max for the MI2S DAIs.
Fixes: 24c4cbcfac ("ASoC: qdsp6: q6afe: Add q6afe dai driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200415150050.616392-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28535877ac upstream.
It should use ad7797_attribute_group in ad7797_info,
according to commit ("iio:ad7793: Add support for the ad7796 and ad7797").
Scale is fixed for the ad7796 and not programmable, hence
should not have the scale_available attribute.
Fixes: fd1a8b9128 ("iio:ad7793: Add support for the ad7796 and ad7797")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09b04abb70 upstream.
When building with Clang + -Wtautological-pointer-compare:
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:28: warning: comparison of
address of 'req->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~ ~~~~
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:51: warning: comparison of
address of 'req->usb_req' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~~~ ~~~~
2 warnings generated.
As it notes, these statements will always evaluate to false so remove
them.
Fixes: efed421a94 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Link: https://github.com/ClangBuiltLinux/linux/issues/749
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0550cd20e upstream.
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c91 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60d4885710 upstream.
Restore the behavior of locking mmap_sem for reading in
binder_alloc_free_page(), as was first done in commit 3013bf62b6
("binder: reduce mmap_sem write-side lock"). That change was
inadvertently reverted by commit 5cec2d2e58 ("binder: fix race between
munmap() and direct reclaim").
In addition, change the name of the label for the error path to
accurately reflect that we're taking the lock for reading.
Backporting note: This fix is only needed when *both* of the commits
mentioned above are applied. That's an unlikely situation since they
both landed during the development of v5.1 but only one of them is
targeted for stable.
Fixes: 5cec2d2e58 ("binder: fix race between munmap() and direct reclaim")
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Acked-by: Todd Kjos <tkjos@android.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 467d12f5c7 upstream.
QEMU has a funny new build error message when I use the upstream kernel
headers:
CC block/file-posix.o
In file included from /home/cborntra/REPOS/qemu/include/qemu/timer.h:4,
from /home/cborntra/REPOS/qemu/include/qemu/timed-average.h:29,
from /home/cborntra/REPOS/qemu/include/block/accounting.h:28,
from /home/cborntra/REPOS/qemu/include/block/block_int.h:27,
from /home/cborntra/REPOS/qemu/block/file-posix.c:30:
/usr/include/linux/swab.h: In function `__swab':
/home/cborntra/REPOS/qemu/include/qemu/bitops.h:20:34: error: "sizeof" is not defined, evaluates to 0 [-Werror=undef]
20 | #define BITS_PER_LONG (sizeof (unsigned long) * BITS_PER_BYTE)
| ^~~~~~
/home/cborntra/REPOS/qemu/include/qemu/bitops.h:20:41: error: missing binary operator before token "("
20 | #define BITS_PER_LONG (sizeof (unsigned long) * BITS_PER_BYTE)
| ^
cc1: all warnings being treated as errors
make: *** [/home/cborntra/REPOS/qemu/rules.mak:69: block/file-posix.o] Error 1
rm tests/qemu-iotests/socket_scm_helper.o
This was triggered by commit d5767057c9 ("uapi: rename ext2_swab() to
swab() and share globally in swab.h"). That patch is doing
#include <asm/bitsperlong.h>
but it uses BITS_PER_LONG.
The kernel file asm/bitsperlong.h provide only __BITS_PER_LONG.
Let us use the __ variant in swap.h
Link: http://lkml.kernel.org/r/20200213142147.17604-1-borntraeger@de.ibm.com
Fixes: d5767057c9 ("uapi: rename ext2_swab() to swab() and share globally in swab.h")
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: Allison Randal <allison@lohutok.net>
Cc: Joe Perches <joe@perches.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b8a67b3b upstream.
In function do_write_buffer(), in the for loop, there is a case
chip_ready() returns 1 while chip_good() returns 0, so it never
break the loop.
To fix this, chip_good() is enough and it should timeout if it stay
bad for a while.
Fixes: dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
Signed-off-by: Yi Huaijie <yihuaijie@huawei.com>
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Tokunori Ikegami <ikegami_to@yahoo.co.jp>
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 316ec15481 upstream.
A page table upgrade in a kernel section that uses secondary address
mode will mess up the kernel instructions as follows:
Consider the following scenario: two threads are sharing memory.
On CPU1 thread 1 does e.g. strnlen_user(). That gets to
old_fs = enable_sacf_uaccess();
len = strnlen_user_srst(src, size);
and
" la %2,0(%1)\n"
" la %3,0(%0,%1)\n"
" slgr %0,%0\n"
" sacf 256\n"
"0: srst %3,%2\n"
in strnlen_user_srst(). At that point we are in secondary space mode,
control register 1 points to kernel page table and instruction fetching
happens via c1, rather than usual c13. Interrupts are not disabled, for
obvious reasons.
On CPU2 thread 2 does MAP_FIXED mmap(), forcing the upgrade of page table
from 3-level to e.g. 4-level one. We'd allocated new top-level table,
set it up and now we hit this:
notify = 1;
spin_unlock_bh(&mm->page_table_lock);
}
if (notify)
on_each_cpu(__crst_table_upgrade, mm, 0);
OK, we need to actually change over to use of new page table and we
need that to happen in all threads that are currently running. Which
happens to include the thread 1. IPI is delivered and we have
static void __crst_table_upgrade(void *arg)
{
struct mm_struct *mm = arg;
if (current->active_mm == mm)
set_user_asce(mm);
__tlb_flush_local();
}
run on CPU1. That does
static inline void set_user_asce(struct mm_struct *mm)
{
S390_lowcore.user_asce = mm->context.asce;
OK, user page table address updated...
__ctl_load(S390_lowcore.user_asce, 1, 1);
... and control register 1 set to it.
clear_cpu_flag(CIF_ASCE_PRIMARY);
}
IPI is run in home space mode, so it's fine - insns are fetched
using c13, which always points to kernel page table. But as soon
as we return from the interrupt, previous PSW is restored, putting
CPU1 back into secondary space mode, at which point we no longer
get the kernel instructions from the kernel mapping.
The fix is to only fixup the control registers that are currently in use
for user processes during the page table update. We must also disable
interrupts in enable_sacf_uaccess to synchronize the cr and
thread.mm_segment updates against the on_each-cpu.
Fixes: 0aaba41b58 ("s390: remove all code using the access register mode")
Cc: stable@vger.kernel.org # 4.15+
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
References: CVE-2020-11884
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc56ad8c74 upstream.
When performing rename operation with RENAME_WHITEOUT flag, we will
hold AGF lock to allocate or free extents in manipulating the dirents
firstly, and then doing the xfs_iunlink_remove() call last to hold
AGI lock to modify the tmpfile info, so we the lock order AGI->AGF.
The big problem here is that we have an ordering constraint on AGF
and AGI locking - inode allocation locks the AGI, then can allocate
a new extent for new inodes, locking the AGF after the AGI. Hence
the ordering that is imposed by other parts of the code is AGI before
AGF. So we get an ABBA deadlock between the AGI and AGF here.
Process A:
Call trace:
? __schedule+0x2bd/0x620
schedule+0x33/0x90
schedule_timeout+0x17d/0x290
__down_common+0xef/0x125
? xfs_buf_find+0x215/0x6c0 [xfs]
down+0x3b/0x50
xfs_buf_lock+0x34/0xf0 [xfs]
xfs_buf_find+0x215/0x6c0 [xfs]
xfs_buf_get_map+0x37/0x230 [xfs]
xfs_buf_read_map+0x29/0x190 [xfs]
xfs_trans_read_buf_map+0x13d/0x520 [xfs]
xfs_read_agf+0xa6/0x180 [xfs]
? schedule_timeout+0x17d/0x290
xfs_alloc_read_agf+0x52/0x1f0 [xfs]
xfs_alloc_fix_freelist+0x432/0x590 [xfs]
? down+0x3b/0x50
? xfs_buf_lock+0x34/0xf0 [xfs]
? xfs_buf_find+0x215/0x6c0 [xfs]
xfs_alloc_vextent+0x301/0x6c0 [xfs]
xfs_ialloc_ag_alloc+0x182/0x700 [xfs]
? _xfs_trans_bjoin+0x72/0xf0 [xfs]
xfs_dialloc+0x116/0x290 [xfs]
xfs_ialloc+0x6d/0x5e0 [xfs]
? xfs_log_reserve+0x165/0x280 [xfs]
xfs_dir_ialloc+0x8c/0x240 [xfs]
xfs_create+0x35a/0x610 [xfs]
xfs_generic_create+0x1f1/0x2f0 [xfs]
...
Process B:
Call trace:
? __schedule+0x2bd/0x620
? xfs_bmapi_allocate+0x245/0x380 [xfs]
schedule+0x33/0x90
schedule_timeout+0x17d/0x290
? xfs_buf_find+0x1fd/0x6c0 [xfs]
__down_common+0xef/0x125
? xfs_buf_get_map+0x37/0x230 [xfs]
? xfs_buf_find+0x215/0x6c0 [xfs]
down+0x3b/0x50
xfs_buf_lock+0x34/0xf0 [xfs]
xfs_buf_find+0x215/0x6c0 [xfs]
xfs_buf_get_map+0x37/0x230 [xfs]
xfs_buf_read_map+0x29/0x190 [xfs]
xfs_trans_read_buf_map+0x13d/0x520 [xfs]
xfs_read_agi+0xa8/0x160 [xfs]
xfs_iunlink_remove+0x6f/0x2a0 [xfs]
? current_time+0x46/0x80
? xfs_trans_ichgtime+0x39/0xb0 [xfs]
xfs_rename+0x57a/0xae0 [xfs]
xfs_vn_rename+0xe4/0x150 [xfs]
...
In this patch we move the xfs_iunlink_remove() call to
before acquiring the AGF lock to preserve correct AGI/AGF locking
order.
[Minor massage required due to upstream change making xfs_bumplink() a
void function where as in the 4.19.y tree the return value is checked,
even though it is always zero. Only change was to the last code block
removed by the patch. Functionally equivalent to upstream.]
Signed-off-by: kaixuxia <kaixuxia@tencent.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Suraj Jitindar Singh <surajjs@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2e54fbf1 upstream.
For userspace functions using OS Descriptors, if a function also supplies
Extended Property descriptors currently the counts and lengths stored in
the ms_os_descs_ext_prop_{count,name_len,data_len} variables are not
getting reset to 0 during an unbind or when the epfiles are closed. If
the same function is re-bound and the descriptors are re-written, this
results in those count/length variables to monotonically increase
causing the VLA allocation in _ffs_func_bind() to grow larger and larger
at each bind/unbind cycle and eventually fail to allocate.
Fix this by clearing the ms_os_descs_ext_prop count & lengths to 0 in
ffs_data_reset().
Fixes: f0175ab519 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <ugoswami@codeaurora.org>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/20200402044521.9312-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49e0590e3a upstream.
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590 ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b59f10b1d upstream.
The problem is that the group key was saved as VNT_KEY_DEFAULTKEY
was over written by the VNT_KEY_GROUP_ADDRESS index.
mac80211 could not clear the mac_addr in the default key.
The VNT_KEY_DEFAULTKEY is not necesscary so remove it and set as
VNT_KEY_GROUP_ADDRESS.
mac80211 can clear any key using vnt_mac_disable_keyentry.
Fixes: f9ef05ce13 ("staging: vt6656: Fix pairwise key for non station modes")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/da2f7e7f-1658-1320-6eee-0f55770ca391@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a98e7a80f upstream.
Even if the actual screen size is bounded in vc_do_resize(), the unicode
buffer is still a little more than twice the size of the glyph buffer
and may exceed MAX_ORDER down the kmalloc() path. This can be triggered
from user space.
Since there is no point having a physically contiguous buffer here,
let's avoid the above issue as well as reducing pressure on high order
allocations by using vmalloc() instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003282214210.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2717769e20 upstream.
The code in vc_do_resize() bounds the memory allocation size to avoid
exceeding MAX_ORDER down the kzalloc() call chain and generating a
runtime warning triggerable from user space. However, not only is it
unwise to use a literal value here, but MAX_ORDER may also be
configurable based on CONFIG_FORCE_MAX_ZONEORDER.
Let's use KMALLOC_MAX_SIZE instead.
Note that prior commit bb1107f7c6 ("mm, slab: make sure that
KMALLOC_MAX_SIZE will fit into MAX_ORDER") the KMALLOC_MAX_SIZE value
could not be relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003281702410.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 332e0e17ad upstream.
comedi_open() invokes comedi_dev_get_from_minor(), which returns a
reference of the COMEDI device to "dev" with increased refcount.
When comedi_open() returns, "dev" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
comedi_open(). When "cfp" allocation is failed, the refcnt increased by
comedi_dev_get_from_minor() is not decreased, causing a refcnt leak.
Fix this issue by calling comedi_dev_put() on this error path when "cfp"
allocation is failed.
Fixes: 20f083c075 ("staging: comedi: prepare support for per-file read and write subdevices")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/1587361459-83622-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed87d33ddb upstream.
The DT2815 analog output command is 16 bits wide, consisting of the
12-bit sample value in bits 15 to 4, the channel number in bits 3 to 1,
and a voltage or current selector in bit 0. Both bytes of the 16-bit
command need to be written in turn to a single 8-bit data register.
However, the driver currently only writes the low 8-bits. It is broken
and appears to have always been broken.
Electronic copies of the DT2815 User's Manual seem impossible to find
online, but looking at the source code, a best guess for the sequence
the driver intended to use to write the analog output command is as
follows:
1. Wait for the status register to read 0x00.
2. Write the low byte of the command to the data register.
3. Wait for the status register to read 0x80.
4. Write the high byte of the command to the data register.
Step 4 is missing from the driver. Add step 4 to (hopefully) fix the
driver.
Also add a "FIXME" comment about setting bit 0 of the low byte of the
command. Supposedly, it is used to choose between voltage output and
current output, but the current driver always sets it to 1.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200406142015.126982-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94c0b013c9 upstream.
If {i,d}-cache-block-size is set and {i,d}-cache-line-size is not, use
the block-size value for both. Per the devicetree spec cache-line-size
is only needed if it differs from the block size.
Originally the code would fallback from block size to line size. An
error message was printed if both properties were missing.
Later the code was refactored to use clearer names and logic but it
inadvertently made line size a required property, meaning on systems
without a line size property we fall back to the default from the
cputable.
On powernv (OPAL) platforms, since the introduction of device tree CPU
features (5a61ef74f2 ("powerpc/64s: Support new device tree binding
for discovering CPU features")), that has led to the wrong value being
used, as the fallback value is incorrect for Power8/Power9 CPUs.
The incorrect values flow through to the VDSO and also to the sysconf
values, SC_LEVEL1_ICACHE_LINESIZE etc.
Fixes: bd067f83b0 ("powerpc/64: Fix naming of cache block vs. cache line")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Qian Cai <cai@lca.pw>
[mpe: Add even more detail to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200416221908.7886-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1baca8896 upstream.
512a928aff ("ARM: imx: build v7_cpu_resume() unconditionally")
introduced an unintended linker error for i.MX6 configurations that have
ARM_CPU_SUSPEND=n which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE,
nor ARM_PSCI_FW are selected.
Fix this by having v7_cpu_resume() compiled only when cpu_resume() it
calls is available as well.
The C declaration for the function remains unguarded to avoid future code
inadvertently using a stub and introducing a regression to the bug the
original commit fixed.
Cc: <stable@vger.kernel.org>
Fixes: 512a928aff ("ARM: imx: build v7_cpu_resume() unconditionally")
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Tested-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebf1474745 upstream.
snd_soc_dapm_kcontrol widget which is created by autodisable control
should contain correct on_val, mask and shift because it is set when the
widget is powered and changed value is applied on registers by following
code in dapm_seq_run_coalesced().
mask |= w->mask << w->shift;
if (w->power)
value |= w->on_val << w->shift;
else
value |= w->off_val << w->shift;
Shift on the mask in dapm_kcontrol_data_alloc() is removed to prevent
double shift.
And, on_val in dapm_kcontrol_set_value() is modified to get correct
value in the dapm_seq_run_coalesced().
Signed-off-by: Gyeongtaek Lee <gt82.lee@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/000001d61537$b212f620$1638e260$@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 763dafc520 upstream.
Commit 7561252892 ("audit: always check the netlink payload length
in audit_receive_msg()") fixed a number of missing message length
checks, but forgot to check the length of userspace generated audit
records. The good news is that you need CAP_AUDIT_WRITE to submit
userspace audit records, which is generally only given to trusted
processes, so the impact should be limited.
Cc: stable@vger.kernel.org
Fixes: 7561252892 ("audit: always check the netlink payload length in audit_receive_msg()")
Reported-by: syzbot+49e69b4d71a420ceda3e@syzkaller.appspotmail.com
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94f9c8c3c4 upstream.
Cyril Roelandt reports that his JMicron JMS566 USB-SATA bridge fails
to handle WRITE commands with the FUA bit set, even though it claims
to support FUA. (Oddly enough, a later version of the same bridge,
version 2.03 as opposed to 1.14, doesn't claim to support FUA. Also
oddly, the bridge _does_ support FUA when using the UAS transport
instead of the Bulk-Only transport -- but this device was blacklisted
for uas in commit bc3bdb12bb ("usb-storage: Disable UAS on JMicron
SATA enclosure") for apparently unrelated reasons.)
This patch adds a usb-storage unusual_devs entry with the BROKEN_FUA
flag. This allows the bridge to work properly with usb-storage.
Reported-and-tested-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221613110.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
