[ Upstream commit 189927e719 ]
Add support for specifying the xtal load capacitance in the DT node.
The pcf8523 supports xtal load capacitance of 7pF or 12.5pF.
If the rtc has the wrong configuration the time will
drift several hours/week.
The driver use the default value 12.5pF.
The DT may specify either 7000fF or 12500fF.
(The DT uses femto Farad to avoid decimal numbers).
Other values are warned and the driver uses the default value.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fdc1790e6 ]
On plug-in of my USB-C device, its USB_SS_PORT_LS_SS_INACTIVE
link state bit is set. Greping all the kernel for this bit shows
that the port status requests a warm-reset this way.
This just happens, if its the only device on the root hub, the hub
therefore resumes and the HCDs status_urb isn't yet available.
If a warm-reset request is detected, this sets the hubs event_bits,
which will prevent any auto-suspend and allows the hubs workqueue
to warm-reset the port later in port_event.
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 202e69e645 ]
XMOS/Thesycon family of USB Audio Class firmware flags DSD altsetting
separate from the PCM ones. Thus the DSD altsetting can be auto-detected
based on the flag and doesn't need maintaining specific altsetting
whitelist.
In addition, static VID:PID-to-altsetting whitelisting causes problems
when firmware update changes the altsetting, or same VID:PID is reused
for another device that has different kind of firmware.
This patch removes existing explicit whitelist mappings for XMOS VID
(0x20b1) and Thesycon VID (0x152a).
Also corrects placement of Hegel HD12 and NuPrime DAC-10 to keep list
sorted based on VID.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acbfa6c26f ]
We must wait until End Transfer completes in order to clear
DWC3_EP_TRANSFER_STARTED, otherwise we may confuse the driver.
This patch is in preparation to fix a rare race condition that happens
upon Disconnect Interrupt.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f45581f5e ]
There is a rare race condition that may happen during a Disconnect
Interrupt if we have a started request that happens to be
dequeued *after* completion of End Transfer command. If that happens,
that request will be left waiting for completion of an End Transfer
command that will never happen.
If End Transfer command has already completed before, we are safe to
giveback the request straight away.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d59dd69d55 ]
When NULL pointer accidentally passed to write_kprobe_events,
due to strlen(NULL), segmentation fault happens.
Changed code returns -1 to deal with this situation.
Bug issued with Smatch, static analysis.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b538cc213 ]
When using this driver with the wireless dongle and some usermode
program that monitors every input device (acpid, for example), while
another usermode client opens and closes the low-level device
repeadedly, the system eventually deadlocks.
The reason is that steam_input_register_device() must not be called with
the mutex held, because the input subsystem has its own synchronization
that clashes with this one: it is possible that steam_input_open() is
called before input_register_device() returns, and since
steam_input_open() needs to lock the mutex, it deadlocks.
However we must hold the mutex when calling any function that sends
commands to the controller. If not, random commands end up falling fail.
Reported-by: Simon Gene Gottlieb <simon@gottliebtfreitag.de>
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Tested-by: Simon Gene Gottlieb <simon@gottliebtfreitag.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf28aee292 ]
There is a new firmware for the Steam Controller with support for BLE
connections. When using such a device with a wired connection, it
reboots itself every 10 seconds unless an application has opened it.
Doing hid_hw_open() unconditionally on probe fixes the issue, and the
code becomes simpler.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a767ffea05 ]
Add ASUS Transbook T100CHI/T90CHI keyboard dock into battery quirk list, in
order to add specific implementation in hid-asus.
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ca1f90861 ]
Instead of reimplement afunction to do 'dt_node_to_map' task like
'rt2880_pinctrl_dt_node_to_map' make use of 'pinconf_generic_dt_node_to_map_all'
generic function for this task. Also use its equivalent function for free which
is 'pinconf_generic_dt_free_map'. Remove 'rt2880_pinctrl_dt_node_to_map' function
which is not needed anymore. This decrease a bit driver LOC and make it more
generic. To properly compile this changes 'GENERIC_PINCONF' option is selected
with the driver in its Kconfig file.
This also fix a problem with function 'rt2880_pinctrl_dt_node_to_map' which was
calling internally 'pinctrl_utils_reserve_map' which expects 'num_maps' to be initialized.
It does a memory allocation based on the value, and triggers the following
warning if is not properly set:
if (unlikely(order >= MAX_ORDER)) {
WARN_ON_ONCE(!(gfp_mask & __GFP_NOWARN));
return NULL;
}
Generic function 'pinconf_generic_dt_node_to_map_all' initializes properly
'num_maps' to zero fixing the problem.
Fixes: e12a1a6e08 ("staging: mt7621-pinctrl: refactor rt2880_pinctrl_dt_node_to_map function")
Reported-by: NeilBrown <neil@brown.name>
Tested-by: NeilBrown <neil@brown.name>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff64dd4857 ]
git-diff-index does not refresh the index for you, so using it for a
"-dirty" check can give misleading results. Commit 6147b1cf19
("scripts/setlocalversion: git: Make -dirty check more robust") tried to
fix this by switching to git-status, but it overlooked the fact that
git-status also writes to the .git directory of the source tree, which
is definitely not kosher for an out-of-tree (O=) build. That is getting
reverted.
Fortunately, git-status now supports avoiding writing to the index via
the --no-optional-locks flag, as of git 2.14. It still calculates an
up-to-date index, but it avoids writing it out to the .git directory.
So, let's retry the solution from commit 6147b1cf19 using this new
flag first, and if it fails, we assume this is an older version of git
and just use the old git-diff-index method.
It's hairy to get the 'grep -vq' (inverted matching) correct by stashing
the output of git-status (you have to be careful about the difference
betwen "empty stdin" and "blank line on stdin"), so just pipe the output
directly to grep and use a regex that's good enough for both the
git-status and git-diff-index version.
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Alexander Kapshuk <alexander.kapshuk@gmail.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Genki Sky <sky@genki.is>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b627f616e ]
The registered clks should unregister when something wrong happens
before going out in function clk_boston_setup().
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a31061833 ]
We lose even config space access when we power gate the ISP
via the PUNIT. That makes lspci & co. produce gibberish.
To fix that let's try to implement actual runtime pm hooks
and inform the pci core that the device always goes to
D3cold. That will cause the pci core to resume the device
before attempting config space access.
This introduces another annoyance though. We get the
following error every time we try to resume the device:
intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
The reason being that the pci core tries to put the device
back into D0 via the standard PCI PM mechanism before
calling the driver resume hook. To fix this properly
we'd need to infiltrate the platform pm hooks (could
turn ugly real fast), or use pm domains (which don't
seem to exist on x86), or some extra early resume
hook for the driver (which doesn't exist either).
So maybe we just choose to live with the error?
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1475af255e ]
While using Elan touchpads, the message floods:
[ 136.138487] i2c_hid i2c-DELL08D6:00: i2c_hid_get_input: incomplete report (14/65535)
Though the message flood is annoying, the device it self works without
any issue. I suspect that the device in question takes too much time to
pull the IRQ back to high after I2C host has done reading its data.
Since the host receives all useful data, let's ignore the input report
when there's no data.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86c31524b2 ]
LG touchscreen (1fd2:8001) stops working after reboot:
[ 4.859153] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 4.936070] i2c_hid i2c-SAPS2101:00: i2c_hid_get_input: incomplete report (64/66)
[ 9.948224] i2c_hid i2c-SAPS2101:00: failed to reset device.
The device in question stops working after receives SLEEP, ON, SLEEP
commands in a short period. The scenario is like this:
- Once the desktop session closes, it also closed the hid device, so the
device gets runtime suspended and receives a SLEEP command.
- Before calling shutdown callback, it gets runtime resumed and received
an ON command.
- In the shutdown callback, it receives another SLEEP command.
I failed to find a reliable interval between ON/SLEEP commands that can
make it work, so let's simply disable runtime PM for the device.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29edbc3ebd ]
Set types bitmap:ipmac and hash:ipmac check that MAC addresses
are not all zeroes.
Introduce one missing check, and make the remaining ones
consistent, using is_zero_ether_addr() instead of comparing
against an array containing zeroes.
This was already done for hash:mac sets in commit 26c97c5d8d
("netfilter: ipset: Use is_zero_ether_addr instead of static and
memcmp").
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4222ea7100 ]
When we are writing out a free space cache, during the transaction commit
phase, we can end up in a deadlock which results in a stack trace like the
following:
schedule+0x28/0x80
btrfs_tree_read_lock+0x8e/0x120 [btrfs]
? finish_wait+0x80/0x80
btrfs_read_lock_root_node+0x2f/0x40 [btrfs]
btrfs_search_slot+0xf6/0x9f0 [btrfs]
? evict_refill_and_join+0xd0/0xd0 [btrfs]
? inode_insert5+0x119/0x190
btrfs_lookup_inode+0x3a/0xc0 [btrfs]
? kmem_cache_alloc+0x166/0x1d0
btrfs_iget+0x113/0x690 [btrfs]
__lookup_free_space_inode+0xd8/0x150 [btrfs]
lookup_free_space_inode+0x5b/0xb0 [btrfs]
load_free_space_cache+0x7c/0x170 [btrfs]
? cache_block_group+0x72/0x3b0 [btrfs]
cache_block_group+0x1b3/0x3b0 [btrfs]
? finish_wait+0x80/0x80
find_free_extent+0x799/0x1010 [btrfs]
btrfs_reserve_extent+0x9b/0x180 [btrfs]
btrfs_alloc_tree_block+0x1b3/0x4f0 [btrfs]
__btrfs_cow_block+0x11d/0x500 [btrfs]
btrfs_cow_block+0xdc/0x180 [btrfs]
btrfs_search_slot+0x3bd/0x9f0 [btrfs]
btrfs_lookup_inode+0x3a/0xc0 [btrfs]
? kmem_cache_alloc+0x166/0x1d0
btrfs_update_inode_item+0x46/0x100 [btrfs]
cache_save_setup+0xe4/0x3a0 [btrfs]
btrfs_start_dirty_block_groups+0x1be/0x480 [btrfs]
btrfs_commit_transaction+0xcb/0x8b0 [btrfs]
At cache_save_setup() we need to update the inode item of a block group's
cache which is located in the tree root (fs_info->tree_root), which means
that it may result in COWing a leaf from that tree. If that happens we
need to find a free metadata extent and while looking for one, if we find
a block group which was not cached yet we attempt to load its cache by
calling cache_block_group(). However this function will try to load the
inode of the free space cache, which requires finding the matching inode
item in the tree root - if that inode item is located in the same leaf as
the inode item of the space cache we are updating at cache_save_setup(),
we end up in a deadlock, since we try to obtain a read lock on the same
extent buffer that we previously write locked.
So fix this by using the tree root's commit root when searching for a
block group's free space cache inode item when we are attempting to load
a free space cache. This is safe since block groups once loaded stay in
memory forever, as well as their caches, so after they are first loaded
we will never need to read their inode items again. For new block groups,
once they are created they get their ->cached field set to
BTRFS_CACHE_FINISHED meaning we will not need to read their inode item.
Reported-by: Andrew Nelson <andrew.s.nelson@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CAPTELenq9x5KOWuQ+fa7h1r3nsJG8vyiTH8+ifjURc_duHh2Wg@mail.gmail.com/
Fixes: 9d66e233c7 ("Btrfs: load free space cache if it exists")
Tested-by: Andrew Nelson <andrew.s.nelson@gmail.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 742bbe1ee3 ]
Currently the Switchtec quirk runs on all endpoints in the switch,
including all the upstream and downstream ports. These other functions do
not contain BARs, so the quirk fails when trying to map the BAR and prints
the error "Cannot iomap Switchtec device". The user will see a few of
these useless and scary errors, one for each port in the switch.
At most, the quirk should only run on either a management endpoint
(PCI_CLASS_MEMORY_OTHER) or an NTB endpoint (PCI_CLASS_BRIDGE_OTHER).
However, the quirk is useless except in NTB applications, so we will
only run it when the class is PCI_CLASS_BRIDGE_OTHER.
Switch to using DECLARE_PCI_FIXUP_CLASS_FINAL and only match
PCI_CLASS_BRIDGE_OTHER.
Reported-by: Stephen Bates <sbates@raithlin.com>
Fixes: ad281ecf1c ("PCI: Add DMA alias quirk for Microsemi Switchtec NTB")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
[bhelgaas: split SWITCHTEC_QUIRK() introduction to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Doug Meyer <dmeyer@gigaio.com>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dab71b2db9 ]
dc->writeback_rate_minimum is type unsigned integer variable, it is set
via sysfs interface, and converte from input string to unsigned integer
by d_strtoul_nonzero(). When the converted input value is larger than
UINT_MAX, overflow to unsigned integer happens.
This patch fixes the overflow by using sysfs_strotoul_clamp() to
convert input string and limit the value in range [1, UINT_MAX], then
the overflow can be avoided.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a802ee99c4 ]
Bail out KMS hw init on display initialization failures with
proper error logging.
changes in v3:
- introduced in the series
changes in v4:
- avoid duplicate return on errors (Sean Paul)
- avoid spamming errors on failures (Jordon Crouse)
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 445640a563 ]
When the C-state limit is 8 on Goldmont, PC10 is enabled.
Previously turbostat saw this as "undefined", and thus assumed
it should not show some counters, such as pc3, pc6, pc7.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd7cd0e6ce ]
When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 399474e4c1 ]
This device uses the SIPODEV SP1064 touchpad, which does not
supply descriptors, so it has to be added to the override list.
Reported-by: Tim Aldridge <taldridge@mac.com>
Signed-off-by: Julian Sax <jsbc@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c093b590e ]
Testcase to reproduce this bug:
1. mkfs.f2fs /dev/sdd
2. mount -t f2fs /dev/sdd /mnt/f2fs
3. touch /mnt/f2fs/file
4. sync
5. chattr +a /mnt/f2fs/file
6. xfs_io -a /mnt/f2fs/file -c "fsync"
7. godown /mnt/f2fs
8. umount /mnt/f2fs
9. mount -t f2fs /dev/sdd /mnt/f2fs
10. xfs_io /mnt/f2fs/file
There is no error when opening this file w/o O_APPEND, but actually,
we expect the correct result should be:
/mnt/f2fs/file: Operation not permitted
The root cause is, in recover_inode(), we recover inode->i_flags more
than F2FS_I(inode)->i_flags, so fix it.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7de36cf3e4 ]
inode.i_gc_failures is used to indicate that skip count of migrating
on blocks of inode, we should guarantee it can be recovered in sudden
power-off case.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30ec514d44 ]
The SC16IS752 has an Enhanced Feature Register which is aliased at the
same address as the Interrupt Identification Register; accessing it
requires that a magic value is written to the Line Configuration
Register. If an interrupt is raised while the EFR is mapped in then
the ISR won't be able to access the IIR, leading to the "Unexpected
interrupt" error messages.
Avoid the problem by claiming a mutex around accesses to the EFR
register, also claiming the mutex in the interrupt handler work
item (this is equivalent to disabling interrupts to interlock against
a non-threaded interrupt handler).
See: https://github.com/raspberrypi/linux/issues/2529
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0667b625 ]
After quota_off, we'll get some dirty blocks. If put_super don't have a chance
to flush them by checkpoint, it causes NULL pointer exception in end_io after
iput(node_inode). (e.g., by checkpoint=disable)
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6470f31927 ]
After being associated with some EDMA rx traffic, upon "down" driver
doesn't free all skbs in the rx ring.
Modify wil_move_all_rx_buff_to_free_list to loop on active list of rx
buffers, unmap the physical memory and free the skb.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd2b007eae ]
[BUG]
For btrfs:qgroup_meta_reserve event, the trace event can output garbage:
qgroup_meta_reserve: 9c7f6acc-b342-4037-bc47-7f6e4d2232d7: refroot=5(FS_TREE) type=DATA diff=2
The diff should always be alinged to sector size (4k), so there is
definitely something wrong.
[CAUSE]
For the wrong @diff, it's caused by wrong parameter order.
The correct parameters are:
struct btrfs_root, s64 diff, int type.
However the parameters used are:
struct btrfs_root, int type, s64 diff.
Fixes: 4ee0d8832c ("btrfs: qgroup: Update trace events for metadata reservation")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8702ba9396 ]
[Background]
Btrfs qgroup uses two types of reserved space for METADATA space,
PERTRANS and PREALLOC.
PERTRANS is metadata space reserved for each transaction started by
btrfs_start_transaction().
While PREALLOC is for delalloc, where we reserve space before joining a
transaction, and finally it will be converted to PERTRANS after the
writeback is done.
[Inconsistency]
However there is inconsistency in how we handle PREALLOC metadata space.
The most obvious one is:
In btrfs_buffered_write():
btrfs_delalloc_release_extents(BTRFS_I(inode), reserve_bytes, true);
We always free qgroup PREALLOC meta space.
While in btrfs_truncate_block():
btrfs_delalloc_release_extents(BTRFS_I(inode), blocksize, (ret != 0));
We only free qgroup PREALLOC meta space when something went wrong.
[The Correct Behavior]
The correct behavior should be the one in btrfs_buffered_write(), we
should always free PREALLOC metadata space.
The reason is, the btrfs_delalloc_* mechanism works by:
- Reserve metadata first, even it's not necessary
In btrfs_delalloc_reserve_metadata()
- Free the unused metadata space
Normally in:
btrfs_delalloc_release_extents()
|- btrfs_inode_rsv_release()
Here we do calculation on whether we should release or not.
E.g. for 64K buffered write, the metadata rsv works like:
/* The first page */
reserve_meta: num_bytes=calc_inode_reservations()
free_meta: num_bytes=0
total: num_bytes=calc_inode_reservations()
/* The first page caused one outstanding extent, thus needs metadata
rsv */
/* The 2nd page */
reserve_meta: num_bytes=calc_inode_reservations()
free_meta: num_bytes=calc_inode_reservations()
total: not changed
/* The 2nd page doesn't cause new outstanding extent, needs no new meta
rsv, so we free what we have reserved */
/* The 3rd~16th pages */
reserve_meta: num_bytes=calc_inode_reservations()
free_meta: num_bytes=calc_inode_reservations()
total: not changed (still space for one outstanding extent)
This means, if btrfs_delalloc_release_extents() determines to free some
space, then those space should be freed NOW.
So for qgroup, we should call btrfs_qgroup_free_meta_prealloc() other
than btrfs_qgroup_convert_reserved_meta().
The good news is:
- The callers are not that hot
The hottest caller is in btrfs_buffered_write(), which is already
fixed by commit 336a8bb8e3 ("btrfs: Fix wrong
btrfs_delalloc_release_extents parameter"). Thus it's not that
easy to cause false EDQUOT.
- The trans commit in advance for qgroup would hide the bug
Since commit f5fef45936 ("btrfs: qgroup: Make qgroup async transaction
commit more aggressive"), when btrfs qgroup metadata free space is slow,
it will try to commit transaction and free the wrongly converted
PERTRANS space, so it's not that easy to hit such bug.
[FIX]
So to fix the problem, remove the @qgroup_free parameter for
btrfs_delalloc_release_extents(), and always pass true to
btrfs_inode_rsv_release().
Reported-by: Filipe Manana <fdmanana@suse.com>
Fixes: 43b18595d6 ("btrfs: qgroup: Use separate meta reservation type for delalloc")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c67d970f0e ]
When we have a buffered write that starts at an offset greater than or
equals to the file's size happening concurrently with a full ranged
fiemap, we can end up leaking an extent state structure.
Suppose we have a file with a size of 1Mb, and before the buffered write
and fiemap are performed, it has a single extent state in its io tree
representing the range from 0 to 1Mb, with the EXTENT_DELALLOC bit set.
The following sequence diagram shows how the memory leak happens if a
fiemap a buffered write, starting at offset 1Mb and with a length of
4Kb, are performed concurrently.
CPU 1 CPU 2
extent_fiemap()
--> it's a full ranged fiemap
range from 0 to LLONG_MAX - 1
(9223372036854775807)
--> locks range in the inode's
io tree
--> after this we have 2 extent
states in the io tree:
--> 1 for range [0, 1Mb[ with
the bits EXTENT_LOCKED and
EXTENT_DELALLOC_BITS set
--> 1 for the range
[1Mb, LLONG_MAX[ with
the EXTENT_LOCKED bit set
--> start buffered write at offset
1Mb with a length of 4Kb
btrfs_file_write_iter()
btrfs_buffered_write()
--> cached_state is NULL
lock_and_cleanup_extent_if_need()
--> returns 0 and does not lock
range because it starts
at current i_size / eof
--> cached_state remains NULL
btrfs_dirty_pages()
btrfs_set_extent_delalloc()
(...)
__set_extent_bit()
--> splits extent state for range
[1Mb, LLONG_MAX[ and now we
have 2 extent states:
--> one for the range
[1Mb, 1Mb + 4Kb[ with
EXTENT_LOCKED set
--> another one for the range
[1Mb + 4Kb, LLONG_MAX[ with
EXTENT_LOCKED set as well
--> sets EXTENT_DELALLOC on the
extent state for the range
[1Mb, 1Mb + 4Kb[
--> caches extent state
[1Mb, 1Mb + 4Kb[ into
@cached_state because it has
the bit EXTENT_LOCKED set
--> btrfs_buffered_write() ends up
with a non-NULL cached_state and
never calls anything to release its
reference on it, resulting in a
memory leak
Fix this by calling free_extent_state() on cached_state if the range was
not locked by lock_and_cleanup_extent_if_need().
The same issue can happen if anything else other than fiemap locks a range
that covers eof and beyond.
This could be triggered, sporadically, by test case generic/561 from the
fstests suite, which makes duperemove run concurrently with fsstress, and
duperemove does plenty of calls to fiemap. When CONFIG_BTRFS_DEBUG is set
the leak is reported in dmesg/syslog when removing the btrfs module with
a message like the following:
[77100.039461] BTRFS: state leak: start 6574080 end 6582271 state 16402 in tree 0 refs 1
Otherwise (CONFIG_BTRFS_DEBUG not set) detectable with kmemleak.
CC: stable@vger.kernel.org # 4.16+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b21555786f ]
Commit 721b1d98fb ("dm snapshot: Fix excessive memory usage and
workqueue stalls") introduced a semaphore to limit the maximum number of
in-flight kcopyd (COW) jobs.
The implementation of this throttling mechanism is prone to a deadlock:
1. One or more threads write to the origin device causing COW, which is
performed by kcopyd.
2. At some point some of these threads might reach the s->cow_count
semaphore limit and block in down(&s->cow_count), holding a read lock
on _origins_lock.
3. Someone tries to acquire a write lock on _origins_lock, e.g.,
snapshot_ctr(), which blocks because the threads at step (2) already
hold a read lock on it.
4. A COW operation completes and kcopyd runs dm-snapshot's completion
callback, which ends up calling pending_complete().
pending_complete() tries to resubmit any deferred origin bios. This
requires acquiring a read lock on _origins_lock, which blocks.
This happens because the read-write semaphore implementation gives
priority to writers, meaning that as soon as a writer tries to enter
the critical section, no readers will be allowed in, until all
writers have completed their work.
So, pending_complete() waits for the writer at step (3) to acquire
and release the lock. This writer waits for the readers at step (2)
to release the read lock and those readers wait for
pending_complete() (the kcopyd thread) to signal the s->cow_count
semaphore: DEADLOCK.
The above was thoroughly analyzed and documented by Nikos Tsironis as
part of his initial proposal for fixing this deadlock, see:
https://www.redhat.com/archives/dm-devel/2019-October/msg00001.html
Fix this deadlock by reworking COW throttling so that it waits without
holding any locks. Add a variable 'in_progress' that counts how many
kcopyd jobs are running. A function wait_for_in_progress() will sleep if
'in_progress' is over the limit. It drops _origins_lock in order to
avoid the deadlock.
Reported-by: Guruswamy Basavaiah <guru2018@gmail.com>
Reported-by: Nikos Tsironis <ntsironis@arrikto.com>
Reviewed-by: Nikos Tsironis <ntsironis@arrikto.com>
Tested-by: Nikos Tsironis <ntsironis@arrikto.com>
Fixes: 721b1d98fb ("dm snapshot: Fix excessive memory usage and workqueue stalls")
Cc: stable@vger.kernel.org # v5.0+
Depends-on: 4a3f111a73a8c ("dm snapshot: introduce account_start_copy() and account_end_copy()")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2f83e8b0c ]
This simple refactoring moves code for modifying the semaphore cow_count
into separate functions to prepare for changes that will extend these
methods to provide for a more sophisticated mechanism for COW
throttling.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3840c5b788 upstream.
Nicolas pointed out that the cxgb4 driver is doing dma off of the stack,
which is generally considered a very bad thing. On some architectures it
could be a security problem, but odds are none of them actually run this
driver, so it's just a "normal" bug.
Resolve this by allocating the memory for a message off of the heap
instead of the stack. kmalloc() always will give us a proper memory
location that DMA will work correctly from.
Link: https://lore.kernel.org/r/20191001165611.GA3542072@kroah.com
Reported-by: Nicolas Waisman <nico@semmle.com>
Tested-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 307f4065b9 upstream.
rq_qos_del() incorrectly assigns the node being deleted to the head if
it was the first on the list in the !prev path. Fix it by iterating
with ** instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Fixes: a79050434b ("blk-rq-qos: refactor out common elements of blk-wbt")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45144d42f2 upstream.
There is an arbitrary difference between the system resume and
runtime resume code paths for PCI devices regarding the delay to
apply when switching the devices from D3cold to D0.
Namely, pci_restore_standard_config() used in the runtime resume
code path calls pci_set_power_state() which in turn invokes
__pci_start_power_transition() to power up the device through the
platform firmware and that function applies the transition delay
(as per PCI Express Base Specification Revision 2.0, Section 6.6.1).
However, pci_pm_default_resume_early() used in the system resume
code path calls pci_power_up() which doesn't apply the delay at
all and that causes issues to occur during resume from
suspend-to-idle on some systems where the delay is required.
Since there is no reason for that difference to exist, modify
pci_power_up() to follow pci_set_power_state() more closely and
invoke __pci_start_power_transition() from there to call the
platform firmware to power up the device (in case that's necessary).
Fixes: db288c9c5f ("PCI / PM: restore the original behavior of pci_set_power_state()")
Reported-by: Daniel Drake <drake@endlessm.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/linux-pm/CAD8Lp44TYxrMgPLkHCqF9hv6smEurMXvmmvmtyFhZ6Q4SE+dig@mail.gmail.com/T/#m21be74af263c6a34f36e0fc5c77c5449d9406925
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d5c1a037d upstream.
xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().
Remove the superfluous module_put().
Fixes: 279f438e36 ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65650b3513 upstream.
It is incorrect to set the cpufreq syscore shutdown callback pointer
to cpufreq_suspend(), because that function cannot be run in the
syscore stage of system shutdown for two reasons: (a) it may attempt
to carry out actions depending on devices that have already been shut
down at that point and (b) the RCU synchronization carried out by it
may not be able to make progress then.
The latter issue has been present since commit 45975c7d21 ("rcu:
Define RCU-sched API in terms of RCU for Tree RCU PREEMPT builds"),
but the former one has been there since commit 90de2a4aa9 ("cpufreq:
suspend cpufreq governors on shutdown") regardless.
Fix that by dropping cpufreq_syscore_ops altogether and making
device_shutdown() call cpufreq_suspend() directly before shutting
down devices, which is along the lines of what system-wide power
management does.
Fixes: 45975c7d21 ("rcu: Define RCU-sched API in terms of RCU for Tree RCU PREEMPT builds")
Fixes: 90de2a4aa9 ("cpufreq: suspend cpufreq governors on shutdown")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
