[ Upstream commit 6960d133f6 ]
NIC is stopped with rtnl_lock held, and during the stop it cancels the
'service_task' work and free irqs.
However, if CONFIG_MACSEC is set, rtnl_lock is acquired both from
aq_nic_service_task and aq_linkstate_threaded_isr. Then a deadlock
happens if aq_nic_stop tries to cancel/disable them when they've already
started their execution.
As the deadlock is caused by rtnl_lock, it causes many other processes
to stall, not only atlantic related stuff.
Fix it by introducing a mutex that protects each NIC's macsec related
data, and locking it instead of the rtnl_lock from the service task and
the threaded IRQ.
Before this patch, all macsec data was protected with rtnl_lock, but
maybe not all of it needs to be protected. With this new mutex, further
efforts can be made to limit the protected data only to that which
requires it. However, probably it doesn't worth it because all macsec's
data accesses are infrequent, and almost all are done from macsec_ops
or ethtool callbacks, called holding rtnl_lock, so macsec_mutex won't
never be much contended.
The issue appeared repeteadly attaching and deattaching the NIC to a
bond interface. Doing that after this patch I cannot reproduce the bug.
Fixes: 62c1c2e606 ("net: atlantic: MACSec offload skeleton")
Reported-by: Li Liang <liali@redhat.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 170a9e341a ]
The offset 12 (bit-rate) of EEPROM SFP DAC (passive) cables is expected
to be in the range 0x64 to 0x68. However, the 5 meter and 7 meter Molex
passive cables have the rate ceiling 0x78 at offset 12.
Add a quirk for Molex passive cables to extend the rate ceiling to 0x78.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09c5f6bf11 ]
The current XGBE code assumes that offset 6 of EEPROM SFP DAC (passive)
cables is NULL. However, some cables (the 5 meter and 7 meter Molex
passive cables) have non-zero data at offset 6. Fix the logic by moving
the passive cable check above the active checks, so as not to be
improperly identified as an active cable. This will fix the issue for
any passive cable that advertises 1000Base-CX in offset 6.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 230db82413 ]
When a console stack dump is initiated with CONFIG_GCOV_PROFILE_ALL
enabled, show_trace_log_lvl() gets out of sync with the ORC unwinder,
causing the stack trace to show all text addresses as unreliable:
# echo l > /proc/sysrq-trigger
[ 477.521031] sysrq: Show backtrace of all active CPUs
[ 477.523813] NMI backtrace for cpu 0
[ 477.524492] CPU: 0 PID: 1021 Comm: bash Not tainted 6.0.0 #65
[ 477.525295] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-1.fc36 04/01/2014
[ 477.526439] Call Trace:
[ 477.526854] <TASK>
[ 477.527216] ? dump_stack_lvl+0xc7/0x114
[ 477.527801] ? dump_stack+0x13/0x1f
[ 477.528331] ? nmi_cpu_backtrace.cold+0xb5/0x10d
[ 477.528998] ? lapic_can_unplug_cpu+0xa0/0xa0
[ 477.529641] ? nmi_trigger_cpumask_backtrace+0x16a/0x1f0
[ 477.530393] ? arch_trigger_cpumask_backtrace+0x1d/0x30
[ 477.531136] ? sysrq_handle_showallcpus+0x1b/0x30
[ 477.531818] ? __handle_sysrq.cold+0x4e/0x1ae
[ 477.532451] ? write_sysrq_trigger+0x63/0x80
[ 477.533080] ? proc_reg_write+0x92/0x110
[ 477.533663] ? vfs_write+0x174/0x530
[ 477.534265] ? handle_mm_fault+0x16f/0x500
[ 477.534940] ? ksys_write+0x7b/0x170
[ 477.535543] ? __x64_sys_write+0x1d/0x30
[ 477.536191] ? do_syscall_64+0x6b/0x100
[ 477.536809] ? entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 477.537609] </TASK>
This happens when the compiled code for show_stack() has a single word
on the stack, and doesn't use a tail call to show_stack_log_lvl().
(CONFIG_GCOV_PROFILE_ALL=y is the only known case of this.) Then the
__unwind_start() skip logic hits an off-by-one bug and fails to unwind
all the way to the intended starting frame.
Fix it by reverting the following commit:
f1d9a2abff ("x86/unwind/orc: Don't skip the first frame for inactive tasks")
The original justification for that commit no longer exists. That
original issue was later fixed in a different way, with the following
commit:
f2ac57a4c4 ("x86/unwind/orc: Fix inactive tasks with stack pointer in %sp on GCC 10 compiled kernels")
Fixes: f1d9a2abff ("x86/unwind/orc: Don't skip the first frame for inactive tasks")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
[jpoimboe: rewrite commit log]
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a9dbec63 ]
The `macb_resume`/`macb_suspend` methods already call the
`phylink_start`/`phylink_stop` methods during their execution so
explicitly say that the PM of the PHY is done by MAC by using the
`mac_managed_pm` flag of the `struct phylink_config`.
This also fixes the warning message issued during resume:
WARNING: CPU: 0 PID: 237 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0x144/0x148
Depends-on: 96de900ae7 ("net: phylink: add mac_managed_pm in phylink_config structure")
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221019120929.63098-1-sergiu.moga@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ec2f4c6b2 ]
In hinic_vf_func_init(), if VF fails to register information with PF
through the MBOX, the MBOX callback function of VF is released once. But
it is released again in hinic_init_hwdev(). Remove one.
Fixes: 7dd29ee128 ("hinic: add sriov feature support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 363cc87767 ]
When hinic_set_cmdq_depth() fails in hinic_init_cmdqs(), the cmdq memory is
not released correctly. Fix it.
Fixes: 72ef908bb3 ("hinic: add three net_device_ops of vf")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c1f602df8 ]
When the input parameter idx meets the expected case option in
hinic_dbg_get_func_table(), read_data is not released. Fix it.
Fixes: 5215e16244 ("hinic: add support to query function table")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0605cd675 ]
The value of lli_credit_cnt is incorrectly assigned, fix it.
Fixes: a0337c0dee ("hinic: add support to set and get irq coalesce")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9442358968 ]
If phy_device_register() fails, phy_device_free() need be called to
put refcount, so memory of phy device and device name can be freed
in callback function.
If get_phy_device() fails, mdiobus_unregister() need be called,
or it will cause warning in mdiobus_free() and kobject is leaked.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019064104.3228892-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82cb4e4612 ]
syzbot found a crash in tipc_topsrv_accept:
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
Workqueue: tipc_rcv tipc_topsrv_accept
RIP: 0010:kernel_accept+0x22d/0x350 net/socket.c:3487
Call Trace:
<TASK>
tipc_topsrv_accept+0x197/0x280 net/tipc/topsrv.c:460
process_one_work+0x991/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e4/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
It was caused by srv->listener that might be set to null by
tipc_topsrv_stop() in net .exit whereas it's still used in
tipc_topsrv_accept() worker.
srv->listener is protected by srv->idr_lock in tipc_topsrv_stop(), so add
a check for srv->listener under srv->idr_lock in tipc_topsrv_accept() to
avoid the null-ptr-deref. To ensure the lsock is not released during the
tipc_topsrv_accept(), move sock_release() after tipc_topsrv_work_stop()
where it's waiting until the tipc_topsrv_accept worker to be done.
Note that sk_callback_lock is used to protect sk->sk_user_data instead of
srv->listener, and it should check srv in tipc_topsrv_listener_data_ready()
instead. This also ensures that no more tipc_topsrv_accept worker will be
started after tipc_conn_close() is called in tipc_topsrv_stop() where it
sets sk->sk_user_data to null.
Fixes: 0ef897be12 ("tipc: separate topology server listener socket from subcsriber sockets")
Reported-by: syzbot+c5ce866a8d30f4be0651@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/4eee264380c409c61c6451af1059b7fb271a7e7b.1666120790.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44f15c1c0 ]
Add 'volatile' to iounmap()'s argument to prevent build warnings.
This make it the same as other major architectures.
Placates these warnings: (12 such warnings)
../drivers/video/fbdev/riva/fbdev.c: In function 'rivafb_probe':
../drivers/video/fbdev/riva/fbdev.c:2067:42: error: passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type [-Werror=discarded-qualifiers]
2067 | iounmap(default_par->riva.PRAMIN);
Fixes: 1162b0701b ("ARC: I/O and DMA Mappings")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: linux-snps-arc@lists.infradead.org
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e705968dd6 ]
In commit 97886d9dcd ("sched: Migration changes for core scheduling"),
sched_group_cookie_match() was added to help determine if a cookie
matches the core state.
However, while it iterates the SMT group, it fails to actually use the
RQ for each of the CPUs iterated, use cpu_rq(cpu) instead of rq to fix
things.
Fixes: 97886d9dcd ("sched: Migration changes for core scheduling")
Signed-off-by: Lin Shengwang <linshengwang1@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20221008022709.642-1-linshengwang1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca6c21327c ]
Marco reported:
Due to the implementation of how SIGTRAP are delivered if
perf_event_attr::sigtrap is set, we've noticed 3 issues:
1. Missing SIGTRAP due to a race with event_sched_out() (more
details below).
2. Hardware PMU events being disabled due to returning 1 from
perf_event_overflow(). The only way to re-enable the event is
for user space to first "properly" disable the event and then
re-enable it.
3. The inability to automatically disable an event after a
specified number of overflows via PERF_EVENT_IOC_REFRESH.
The worst of the 3 issues is problem (1), which occurs when a
pending_disable is "consumed" by a racing event_sched_out(), observed
as follows:
CPU0 | CPU1
--------------------------------+---------------------------
__perf_event_overflow() |
perf_event_disable_inatomic() |
pending_disable = CPU0 | ...
| _perf_event_enable()
| event_function_call()
| task_function_call()
| /* sends IPI to CPU0 */
<IPI> | ...
__perf_event_enable() +---------------------------
ctx_resched()
task_ctx_sched_out()
ctx_sched_out()
group_sched_out()
event_sched_out()
pending_disable = -1
</IPI>
<IRQ-work>
perf_pending_event()
perf_pending_event_disable()
/* Fails to send SIGTRAP because no pending_disable! */
</IRQ-work>
In the above case, not only is that particular SIGTRAP missed, but also
all future SIGTRAPs because 'event_limit' is not reset back to 1.
To fix, rework pending delivery of SIGTRAP via IRQ-work by introduction
of a separate 'pending_sigtrap', no longer using 'event_limit' and
'pending_disable' for its delivery.
Additionally; and different to Marco's proposed patch:
- recognise that pending_disable effectively duplicates oncpu for
the case where it is set. As such, change the irq_work handler to
use ->oncpu to target the event and use pending_* as boolean toggles.
- observe that SIGTRAP targets the ctx->task, so the context switch
optimization that carries contexts between tasks is invalid. If
the irq_work were delayed enough to hit after a context switch the
SIGTRAP would be delivered to the wrong task.
- observe that if the event gets scheduled out
(rotation/migration/context-switch/...) the irq-work would be
insufficient to deliver the SIGTRAP when the event gets scheduled
back in (the irq-work might still be pending on the old CPU).
Therefore have event_sched_out() convert the pending sigtrap into a
task_work which will deliver the signal at return_to_user.
Fixes: 97ba62b278 ("perf: Add support for SIGTRAP on perf events")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Debugged-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Marco Elver <elver@google.com>
Debugged-by: Marco Elver <elver@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Marco Elver <elver@google.com>
Tested-by: Marco Elver <elver@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9a3545b1d ]
Update HDMI volatile registers list as DMA, Channel Selection registers,
vbit control registers are being reflected by hardware DP port
disconnection.
This update is required to fix no display and no sound issue observed
after reconnecting TAMA/SANWA DP cables.
Once DP cable is unplugged, DMA control registers are being reset by
hardware, however at second plugin, new dma control values does not
updated to the dma hardware registers since new register value and
cached values at the time of first plugin are same.
Fixes: 7cb37b7bd0 ("ASoC: qcom: Add support for lpass hdmi driver")
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reported-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Link: https://lore.kernel.org/r/1665637711-13300-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05c2224d4b ]
It's required by vm_userspace_mem_region_add() that memory size
should be aligned to host page size. However, one guest page is
provided by memslot_modification_stress_test. It triggers failure
in the scenario of 64KB-page-size-host and 4KB-page-size-guest,
as the following messages indicate.
# ./memslot_modification_stress_test
Testing guest mode: PA-bits:40, VA-bits:48, 4K pages
guest physical test memory: [0xffbfff0000, 0xffffff0000)
Finished creating vCPUs
Started all vCPUs
==== Test Assertion Failure ====
lib/kvm_util.c:824: vm_adjust_num_guest_pages(vm->mode, npages) == npages
pid=5712 tid=5712 errno=0 - Success
1 0x0000000000404eeb: vm_userspace_mem_region_add at kvm_util.c:822
2 0x0000000000401a5b: add_remove_memslot at memslot_modification_stress_test.c:82
3 (inlined by) run_test at memslot_modification_stress_test.c:110
4 0x0000000000402417: for_each_guest_mode at guest_modes.c:100
5 0x00000000004016a7: main at memslot_modification_stress_test.c:187
6 0x0000ffffb8cd4383: ?? ??:0
7 0x0000000000401827: _start at :?
Number of guest pages is not compatible with the host. Try npages=16
Fix the issue by providing 16 guest pages to the memory slot for this
particular combination of 64KB-page-size-host and 4KB-page-size-guest
on aarch64.
Fixes: ef4c9f4f65 ("KVM: selftests: Fix 32-bit truncation of vm_get_max_gfn()")
Signed-off-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221013063020.201856-1-gshan@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb9ea2c31f ]
The doc says the I²C device's name is used if devname is NULL, but
actually the I²C device driver's name is used.
Fixes: 0658293012 ("media: v4l: subdev: Add a function to set an I²C sub-device's name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 406e14808e upstream.
Before switching back to the right partition in mmc_blk_reset there used
to be a check if hw_reset was even supported. This return value
was removed, so there is no reason to check. Furthermore ensure
part_curr is not falsely set to a valid value on reset or
partition switch error.
As part of this change the code paths of mmc_blk_reset calls were checked
to ensure no commands are issued after a failed mmc_blk_reset directly
without going through the block layer.
Fixes: fefdd3c91e ("mmc: core: Drop superfluous validations in mmc_hw|sw_reset()")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/e91be6199d04414a91e20611c81bfe1d@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1c5e670d6a.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its one of the partial Path Split patches
that was included.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c56cc7fefc.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its one of the partial Path Split patches
that was included.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b4543dbea8.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its one of the partial Path Split patches
that was included.
NOTE: fixed a git revert error which caused a new line to be inserted:
line 5755 of lpfc_scsi.c in lpfc_queuecommand
+ atomic_inc(&ndlp->cmd_pending);
Removed the line
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9a570069cd.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its a fix specific to the Path Split patches,
which were partially included and now being pulled from 5.15.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6e99860de6.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its a fix specific to the Path Split patches,
which were partially included and now being pulled from 5.15.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17bf429b91.
LTS 5.15 pulled in several lpfc "SLI Path split" patches. The Path
Split mods were a 14-patch set, which refactors the driver from
to split the sli-3 hw (now eol) from the sli-4 hw and use sli4
structures natively. The patches are highly inter-related.
Given only some of the patches were included, it created a situation
where FLOGI's fail, thus SLI Ports can't start communication.
Reverting this patch as its a fix specific to the Path Split patches,
which were partially included and now being pulled from 5.15.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ec803025c upstream.
For some exception types the instruction address points behind the
instruction that caused the exception. Take that into account and add
the missing exception table entry.
Cc: <stable@vger.kernel.org>
Fixes: f058599e22 ("s390/pci: Fix s390_mmio_read/write with MIO")
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a262d3ad6a upstream.
For some exception types the instruction address points behind the
instruction that caused the exception. Take that into account and add
the missing exception table entry.
Cc: <stable@vger.kernel.org>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fd9df10cb upstream.
Since commit d9820ff ("ARC: mm: switch pgtable_t back to struct page *")
a memory leakage problem occurs. Memory allocated for page table entries
not released during process termination. This issue can be reproduced by
a small program that allocates a large amount of memory. After several
runs, you'll see that the amount of free memory has reduced and will
continue to reduce after each run. All ARC CPUs are effected by this
issue. The issue was introduced since the kernel stable release v5.15-rc1.
As described in commit d9820ff after switch pgtable_t back to struct
page *, a pointer to "struct page" and appropriate functions are used to
allocate and free a memory page for PTEs, but the pmd_pgtable macro hasn't
changed and returns the direct virtual address from the PMD (PGD) entry.
Than this address used as a parameter in the __pte_free() and as a result
this function couldn't release memory page allocated for PTEs.
Fix this issue by changing the pmd_pgtable macro and returning pointer to
struct page.
Fixes: d9820ff76f ("ARC: mm: switch pgtable_t back to struct page *")
Cc: Mike Rapoport <rppt@kernel.org>
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Pavel Kozlov <pavel.kozlov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d917a62af8 upstream.
The signal_read(), action_read(), and action_write() callbacks have been
assuming Signal0 is requested without checking. This results in requests
for Signal1 returning data for Signal0. This patch fixes these
oversights by properly checking for the Signal's id in the respective
callbacks and handling accordingly based on the particular Signal
requested. The trig_inverted member of the mchp_tc_data is removed as
superfluous.
Fixes: 106b104137 ("counter: Add microchip TCB capture counter")
Cc: stable@vger.kernel.org
Reviewed-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
Link: https://lore.kernel.org/r/20221018121014.7368-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6746eae4bb upstream.
cti_enable_hw() and cti_disable_hw() are called from an atomic context
so shouldn't use runtime PM because it can result in a sleep when
communicating with firmware.
Since commit 3c66563378 ("Revert "firmware: arm_scmi: Add clock
management to the SCMI power domain""), this causes a hang on Juno when
running the Perf Coresight tests or running this command:
perf record -e cs_etm//u -- ls
This was also missed until the revert commit because pm_runtime_put()
was called with the wrong device until commit 692c9a499b ("coresight:
cti: Correct the parameter for pm_runtime_put")
With lock and scheduler debugging enabled the following is output:
coresight cti_sys0: cti_enable_hw -- dev:cti_sys0 parent: 20020000.cti
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1151
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 330, name: perf-exec
preempt_count: 2, expected: 0
RCU nest depth: 0, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<0000000000000000>] 0x0
hardirqs last disabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last enabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 3 PID: 330 Comm: perf-exec Not tainted 6.0.0-00053-g042116d99298 #7
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Sep 13 2022
Call trace:
dump_backtrace+0x134/0x140
show_stack+0x20/0x58
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
__might_resched+0x180/0x228
__might_sleep+0x50/0x88
__pm_runtime_resume+0xac/0xb0
cti_enable+0x44/0x120
coresight_control_assoc_ectdev+0xc0/0x150
coresight_enable_path+0xb4/0x288
etm_event_start+0x138/0x170
etm_event_add+0x48/0x70
event_sched_in.isra.122+0xb4/0x280
merge_sched_in+0x1fc/0x3d0
visit_groups_merge.constprop.137+0x16c/0x4b0
ctx_sched_in+0x114/0x1f0
perf_event_sched_in+0x60/0x90
ctx_resched+0x68/0xb0
perf_event_exec+0x138/0x508
begin_new_exec+0x52c/0xd40
load_elf_binary+0x6b8/0x17d0
bprm_execve+0x360/0x7f8
do_execveat_common.isra.47+0x218/0x238
__arm64_sys_execve+0x48/0x60
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.4+0xfc/0x120
do_el0_svc+0x34/0xc0
el0_svc+0x40/0x98
el0t_64_sync_handler+0x98/0xc0
el0t_64_sync+0x170/0x174
Fix the issue by removing the runtime PM calls completely. They are not
needed here because it must have already been done when building the
path for a trace.
Fixes: 835d722ba1 ("coresight: cti: Initial CoreSight CTI Driver")
Cc: stable <stable@kernel.org>
Reported-by: Aishwarya TCV <Aishwarya.TCV@arm.com>
Reported-by: Cristian Marussi <Cristian.Marussi@arm.com>
Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: James Clark <james.clark@arm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Tested-by: Mike Leach <mike.leach@linaro.org>
[ Fix build warnings ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20221025131032.1149459-1-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
