Add notifier for speed transitions. Keep a count of CPU active
microseconds times current frequency, converted to a percentage relative
to the current frequency when load is evaluated.
Change-Id: I5c27adb11081c50490219784ca57cc46e97fc28c
Signed-off-by: Todd Poynor <toddpoynor@google.com>
The longer-term load since last speed change isn't terribly useful,
may delay recognition of dropping load, and would need forthcoming
changes to adjust load for changing CPU speeds. Drop it.
Change-Id: Ic3cbb0542cc3484617031787e03ed9bdd632dec1
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Accept a string of target loads and speeds at which to apply the
target loads, per the documentation update in this patch. For example,
"85 1000000:90 1700000:99" targets CPU load 85% below speed 1GHz, 90%
at or above 1GHz, until 1.7GHz and above, at which load 99% is targeted.
Attempt to avoid oscillations by evaluating the current speed
weighted by current load against each new choice of speed, choosing a
higher speed if the current load requires a higher speed.
Change-Id: Ie3300206047c84eca5a26b0b63ea512e5207550e
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Apply above_hispeed_delay whenever increasing speed to a new speed above
hispeed (not just the first step above hispeed).
Change-Id: Ibb7add7db47f2a4306a9458c4e1ebabb60698636
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Add a target_load attribute that specifies how aggressively the governor is
to adjust speed to meet the observed load. New target speed is calculated
as the current actual speed (may be higher than target speed on SMP) times
the CPU load (as a fraction) divided by target load (fraction).
cpufreq_frequency_table_target() call use CPUFREQ_RELATION_L to set
the next higher speed rather than next lower speed.
Change-Id: If432451da82f5fed12e15c9421d7d27792376150
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Tracing adds actual speed since this is expected to be key to the
choice of target speed.
Change-Id: Iec936102d0010c4e9dfa143c38a9fd0d551189c3
Signed-off-by: Todd Poynor <toddpoynor@google.com>
create_bulk_endpoints should not be __init since it is called when
accessory is enabled.
Change-Id: Iac6e9f29d53c93760e926efd8e7603432632acb4
Signed-off-by: Todd Poynor <toddpoynor@google.com>
If create_if_tag_stat fails to allocate memory (GFP_ATOMIC) the
following will happen:
qtaguid: iface_stat: tag stat alloc failed
...
kernel BUG at xt_qtaguid.c:1482!
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
The deferrable timer list isn't checked on all idle exits, such as when
hi-res timers expire or ISRs schedule workers. If the idle loop is
exited and it's past time to run the governor load polling timer,
run it immediately. This ensures we handle load spikes caused by actvity
that does not run the normal timer list.
Rename the field that timestamps the "time_in_idle" value to be more
accurate.
Change-Id: Ied590ecbefc83c9a9ec5eb9e31903557f6fa1614
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Avoid wakeups only to handle the governor timer when the system is otherwise
idle.
For platforms where the power cost of remaining in idle at higher CPU
speed may outweigh the cost of a governor wakeup from idle to lower the speed,
set parameter cpufreq_interactive.governidle=1.
Change-Id: Id6c43eb35caecf9b0574fcdd5b769711bc7e6de6
Signed-off-by: LianWei WANG <a22439@motorola.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Helps avoid waking up other CPUs to react to activity on the local CPU.
Change-Id: Ife272aaa7916894a437705d44521b1a1693fbe8e
Signed-off-by: Todd Poynor <toddpoynor@google.com>
debug_console_write calls debug_uart_flush, which will usually wait
until the serial port fifo empties. If another thread is continuously
calling fiq_tty_write, the fifo will constantly be refilled and
debug_uart_flush might never return.
Add a spinlock that is locked in debug_console_write and fiq_tty_write
to ensure they can't run at the same time. This has an extra advantage
of preventing lines from the console and tty from being mixed together.
Also reduce the size returned by fiq_tty_write_room to keep the time
spent with the spinlock held to a reasonable value.
In addition, make sure fiq context can't loop forever by never calling
debug_uart_flush when the console is enabled.
Change-Id: I5712b01f740ca0c84f680d2032c9fa16b7656939
Signed-off-by: Colin Cross <ccross@android.com>
When a new charge source is set, enable charging and set the charging
current, unless we've paused charging due to battery full or battery
health problems.
Change-Id: I129e621c455a941e264dc431b4eb9db6a17c9f7b
Signed-off-by: Danke Xie <d.xie@sta.samsung.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
iio_event_chrdev_read would return -EFAULT if the user-space page was
not resident.
Change-Id: I4ac5d3bc791bb503d014d9db576b9d6d522505b2
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Only check battery health when connected to a charger.
Change-Id: I43e3f73ac1e5862f8e6dbaa19daa6d322f3bba20
Signed-off-by: HongMin Son <hongmin.son@samsung.com>
qtudev_open() could return with a uid_tag_data_tree_lock held
when an kzalloc(..., GFP_ATOMIC) would fail.
Very unlikely to get triggered AND survive the mayhem of running out of mem.
Signed-off-by: JP Abgrall <jpa@google.com>
Alarmtimer may execute the monitor early in the resume sequence. Freeze the
monitor while suspended, and unfreeze after the battery charger and fuel gauge,
etc. drivers are resumed.
Change-Id: Iefda1c642d4b2440169d90d2bee2888fc70e030a
Signed-off-by: Todd Poynor <toddpoynor@google.com>
This patch adds a debugfs file called "shrinker" when read this calls
all the shrinkers in the system with nr_to_scan set to zero and prints
the result. These results are the number of objects the shrinkers have
available and can thus be used an indication of the total memory
that would be availble to the system if a shrink occurred.
Change-Id: Ied0ee7caff3d2fc1cb4bb839aaafee81b5b0b143
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
- Alarm Timer driver is suspended before battery driver, so alarm
timer was not changed to slow poll speed at suspend. Use PM
notifiers instead.
- If charger is connected, keep 1 min alarm timer.
Signed-off-by: HongMin Son <hongmin.son@samsung.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Change-Id: Id0f3bda5d0749fd90f1964073bc30c1a73fc317f
If charger was connected and a charge source change event occurs such that
the charger is still connected (or a different charge source connected),
do not overwrite an existing state such as full or not-charging. Only
switch from discharging to charging on a charge source change event.
Change-Id: I1b841c8f3a92bf15074999e18b17d1d19ce028d7
Signed-off-by: Todd Poynor <toddpoynor@google.com>
When load is below go_hispeed_load, apply the percentage of CPU load to
a max frequency of hispeed_freq instead of the max speed. This avoids
jumping too quickly to hispeed_freq when it is a relatively low
percentage of max speed. This also allows go_hispeed_load to be set to
a high percentage relative to hispeed_freq (as a percentage of max speed,
again useful when hispeed_freq is a low fraction of max speed), to cap
larger loads at hispeed_freq. For example, a load of 60% will typically
move to 60% of hispeed_freq, not 60% of max speed. This causes the
governor to apply two different speed caps, depending on whether load is
below or above go_hispeed_load.
Also fix the type of hispeed_freq, which was u64, to match other
speed data types (and avoid overhead and allow division).
Change-Id: Ie2d0668be161c074aaad77db2037505431457b3a
Signed-off-by: Todd Poynor <toddpoynor@google.com>
The conversion to use oom_score_adj instead of the deprecated oom_adj
values breaks existing user-space code. Add a config option to convert
oom_adj values written to oom_score_adj values if they appear to be
valid oom_adj values.
Change-Id: I68308125059b802ee2991feefb07e9703bc48549
Signed-off-by: Arve Hjønnevåg <arve@android.com>
First bump speed up to hispeed_freq whenever the current speed is below
hispeed_freq, instead of only when the current speed is the minimum speed.
The previous code made it too difficult to use hispeed_freq as a common
intermediate speed on systems that frequently run at speeds between
minimum and hispeed_freq.
Change-Id: I04ec30bafabf5741e267ff289209b8c2d846824b
Signed-off-by: Todd Poynor <toddpoynor@google.com>
ffs_func_eps_enable always take the highspeed usb_endpoint_descriptor
if it is available. Choose the correct usb_endpoint_descriptor
depending on the gadget speed instead.
Change-Id: I5b8444cfdf1b6fe1eef25525fb7a0a0f617a353e
Signed-off-by: Benoit Goby <benoit@android.com>
This driver presents a standard USB audio class interface to the host
and an ALSA PCM device to userspace
Change-Id: If16b14a5ff27045f9cb2daaf1ae9195c5eeab7d0
Signed-off-by: Mike Lockwood <lockwood@google.com>
The control request will be used by the host to enable/disable USB audio
and the ioctl will be used by userspace to read the audio mode
Change-Id: I81c38611b588451e80eacdccc417ca6e11c60cab
Signed-off-by: Mike Lockwood <lockwood@google.com>
Place SLPZ pin in sleep state at system suspend time if a GPIO is
provided by board platform data.
Change-Id: I93c61fa0ae474e968e0f909209c9bfcaafe3dd2c
Signed-off-by: Todd Poynor <toddpoynor@google.com>
In the past, a process could only see its own stats (uid-based summary,
and details).
Now we allow any process to see other UIDs uid-based stats, but still
hide the detailed stats.
Change-Id: I7666961ed244ac1d9359c339b048799e5db9facc
Signed-off-by: JP Abgrall <jpa@google.com>
Same units as power_supply, don't need 1/10000 deg C and conversion
is error-prone.
Change-Id: I8cf146d2a7725df2dacc415daa66b2986b69f2a7
Signed-off-by: Todd Poynor <toddpoynor@google.com>
For reflecting board-level decisions on whether USB or AC charger
is connected, which may differ from charger power supply notion
of USB input path (which may be connected to an AC charger) vs.
AC input path.
Change-Id: I9d2eb446db8b4d9496ba7ce1472d0e7a4d4e24ef
[toddpoynor@google.com: refactoring]
Signed-off-by: hongmin.son <hongmin.son@samsung.com>
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Avoid shutdown due to battery capacity or temperature out of range.
Change-Id: I54abe4dc54bf2fb8a9b972a3940e6fd93cc60473
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Since the smp call to stop the other cpus are handled in those
cpus in interrupt context, there's a potential for those smp
handlers to interrupt threads holding spin locks (such as the
one a mutex holds). This prevents those threads from ever
releasing their spin lock, so if the cpu doing the shutdown
is allowed to switch to another thread that tries to grab the
same lock/mutex, we could get into a deadlock (the spin lock
call is called with preemption disabled in the mutex lock code).
To avoid that possibility, disable preemption before doing the
smp_send_stop().
Change-Id: I7976c5382d7173fcb3cd14da8cc5083d442b2544
Signed-off-by: Mike J. Chen <mjchen@google.com>
Based on Tuna code from 3.0 ported to 3.4 alarm API.
Change-Id: I9b13209963d5a5043237e9e29f3cb07c40583af2
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Add a generic battery power supply and glue logic for talking to the
board battery driver. This driver handles common chores such as:
* periodic battery level and health monitoring
* kernel log reporting and other debugging features for key
properties provided by different charger, fuel gauge, etc.
components
* ensure properties such as battery health are made available to
userspace
* common processing for board-level battery/case temperature sensors
and policy for charging status based on battery health
Based on work by himihee.seo@samsung.com, ms925.kim@samsung.com, and
joshua.chang@samsung.com.
Change-Id: I5fa8e8d68811d84820b7a130b0245ad2b5b6d36b
Signed-off-by: Todd Poynor <toddpoynor@google.com>
mmc_sdio_init_card function is doing necessary initialization
Change-Id: I7d2e432b2af8a76267378acba07e3e4e8fd1e6bc
Signed-off-by: Hosung Kim <hosung0.kim@samsung.com>
kernel_restart cannot be called from interrupt context. Add support for
commands called from a work function, and implement the "reboot" command
there. Also rename the existing irq-mode command to "reset" and change
it to use machine_restart instead of kernel_restart.
Change-Id: I3c423147c01db03d89e95a5b99096ca89462079f
Signed-off-by: Colin Cross <ccross@android.com>
Not useful to have a separate, non-realtime workqueue for speed down
events, avoid priority inversion for speed up events.
Change-Id: Iddcd05545245c847aa1bbe0b8790092914c813d2
Signed-off-by: Todd Poynor <toddpoynor@google.com>
