commit 34ffb33e09 upstream.
The 'ni_at_a2150' module links to `cfc_write_to_buffer` in the
'comedi_fc' module, so selecting 'COMEDI_NI_AT_A2150' in the kernel config
needs to also select 'COMEDI_FC'.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c43435d772 upstream.
comedi_auto_config() associates a Comedi minor device number with an
auto-configured hardware device and comedi_auto_unconfig() disassociates
it. Currently, these use the hardware device's private data pointer to
point to some allocated storage holding the minor device number. This
is a bit of a waste of the hardware device's private data pointer,
preventing it from being used for something more useful by the low-level
comedi device drivers. For example, it would make more sense if
comedi_usb_auto_config() was passed a pointer to the struct
usb_interface instead of the struct usb_device, but this cannot be done
currently because the low-level comedi drivers already use the private
data pointer in the struct usb_interface for something more useful.
This patch stops the comedi core hijacking the hardware device's private
data pointer. Instead, comedi_auto_config() stores a pointer to the
hardware device's struct device in the struct comedi_device_file_info
associated with the minor device number, and comedi_auto_unconfig()
calls new function comedi_find_board_minor() to recover the minor device
number associated with the hardware device.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e43a028752 upstream.
When remembering the direction of a DCR transaction, we should write
to the same variable that we interpret on later when doing vcpu_run
again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6491d4d028 upstream.
The dma_pte_free_pagetable() function will only free a page table page
if it is asked to free the *entire* 2MiB range that it covers. So if a
page table page was used for one or more small mappings, it's likely to
end up still present in the page tables... but with no valid PTEs.
This was fine when we'd only be repopulating it with 4KiB PTEs anyway
but the same virtual address range can end up being reused for a
*large-page* mapping. And in that case were were trying to insert the
large page into the second-level page table, and getting a complaint
from the sanity check in __domain_mapping() because there was already a
corresponding entry. This was *relatively* harmless; it led to a memory
leak of the old page table page, but no other ill-effects.
Fix it by calling dma_pte_clear_range (hopefully redundant) and
dma_pte_free_pagetable() before setting up the new large page.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Tested-by: Ravi Murty <Ravi.Murty@intel.com>
Tested-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96e5d1d3ad upstream.
In gfs2_trans_add_bh(), gfs2 was testing if a there was a bd attached to the
buffer without having the gfs2_log_lock held. It was then assuming it would
stay attached for the rest of the function. However, without either the log
lock being held of the buffer locked, __gfs2_ail_flush() could detach bd at any
time. This patch moves the locking before the test. If there isn't a bd
already attached, gfs2 can safely allocate one and attach it before locking.
There is no way that the newly allocated bd could be on the ail list,
and thus no way for __gfs2_ail_flush() to detach it.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 55c1945eda upstream.
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad1 "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07e72b95f5 upstream.
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
