commit e8bfa04224 upstream.
The clcd device is lacking an interrupt-parent property, which makes
the interrupt unusable and shows up as a warning with the latest
dtc version:
arch/arm/boot/dts/ste-nomadik-s8815.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
arch/arm/boot/dts/ste-nomadik-nhk15.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
I looked up the old board files and found that this interrupt has
the same irqchip as all the other on-chip device, it just needs one
extra line.
Fixes: 17470b7da1 ("ARM: dts: add the CLCD LCD display to the NHK15")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ac1f59c09 upstream.
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca32e0c4bf upstream.
dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/questions/59497/alsa-asoc-how-to-correctly-load-devices-drivers/62217#62217
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 566bd8902e upstream.
SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.
Fixes: 1fb47e0a9b ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes")
Cc: stable@vger.kernel.org
Reported-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dd0d2d22a upstream.
For some reason, the implementation of some 16-bit ID system calls
(namely, setuid16/setgid16 and setfsuid16/setfsgid16) used type cast
instead of low2highgid/low2highuid macros for converting [GU]IDs, which
led to incorrect handling of value of -1 (which ought to be considered
invalid).
Discovered by strace test suite.
Cc: stable@vger.kernel.org
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fa4680b86 upstream.
Some OpenPOWER boxes can have same pstate values for nominal and
pmin pstates. In these boxes the current code will not initialize
'powernv_pstate_info.min' variable and result in erroneous CPU
frequency reporting. This patch fixes this problem.
Fixes: 09ca4c9b59 (cpufreq: powernv: Replacing pstate_id with frequency table index)
Reported-by: Alvin Wang <wangat@tw.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f301e06de upstream.
The following sequence:
* Change queue pair state into IB_QPS_ERR.
* Post a work request on the queue pair.
Triggers the following race condition in the rdma_rxe driver:
* rxe_qp_error() triggers an asynchronous call of rxe_completer(), the function
that examines the QP send queue.
* rxe_post_send() posts a work request on the QP send queue.
If rxe_completer() runs prior to rxe_post_send(), it will drain the send
queue and the driver will assume no further action is necessary.
However, once we post the send to the send queue, because the queue is
in error, no send completion will ever happen and the send will get
stuck. In order to process the send, we need to make sure that
rxe_completer() gets run after a send is posted to a queue pair in an
error state. This patch ensures that happens.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Moni Shoua <monis@mellanox.com>
Cc: <stable@vger.kernel.org> # v4.8
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c1baad223 upstream.
Running the compaction_test sometimes results in out-of-memory
failures. When I debugged this, it turned out that the code to
reset the number of hugepages to the initial value is simply
broken since we write into an open sysctl file descriptor
multiple times without seeking back to the start.
Adding the lseek here fixes the problem.
Cc: stable@vger.kernel.org
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://bugs.linaro.org/show_bug.cgi?id=3145
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 852f692759 upstream.
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Fixes: 4196670be7 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87b3524cb5 upstream.
This failure exists with qib:
ver_rc_compare_swap:
mismatch, sequence 2, expected 123456789abcdef, got 0
The request builder was using the incorrect inlines to
build the request header resulting in incorrect data
in the atomic header.
Fix by using the appropriate inlines to create the request.
Fixes: 261a435184 ("IB/qib,IB/hfi: Use core common header file")
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dd601fa83 upstream.
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da843 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com>
Cc: stable@vger.kernel.org (v3.14+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec897569ad upstream.
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ac8ff95f4 upstream.
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d15d662e89 upstream.
ALSA sequencer core initializes the event pool on demand by invoking
snd_seq_pool_init() when the first write happens and the pool is
empty. Meanwhile user can reset the pool size manually via ioctl
concurrently, and this may lead to UAF or out-of-bound accesses since
the function tries to vmalloc / vfree the buffer.
A simple fix is to just wrap the snd_seq_pool_init() call with the
recently introduced client->ioctl_mutex; as the calls for
snd_seq_pool_init() from other side are always protected with this
mutex, we can avoid the race.
Reported-by: 范龙飞 <long7573@126.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e35dc0338 upstream.
Add quirk to ensure a sync endpoint is properly configured.
This patch is a fix for same symptoms on Behringer UFX1204 as patch
from Albertto Aquirre on Dec 8 2016 for Axe-Fx II.
Signed-off-by: Lassi Ylikojola <lassi.ylikojola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdcc968a3b upstream.
These laptops have a combined jack to attach headsets, the U727 on
the left, the U757 on the right, but a headsets microphone doesn't
work. Using hdajacksensetest I found that pin 0x19 changed the
present state when plugging the headset, in addition to 0x21, but
didn't have the correct configuration (shown as "Not connected").
So this sets the configuration to the same values as the headphone
pin 0x21 except for the device type microphone, which makes it
work correctly. With the patch the configured pins for U727 are
Pin 0x12 (Internal Mic, Mobile-In): present = No
Pin 0x14 (Internal Speaker): present = No
Pin 0x19 (Black Mic, Left side): present = No
Pin 0x1d (Internal Aux): present = No
Pin 0x21 (Black Headphone, Left side): present = No
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61fcf8ece9 upstream.
Thinkpad Dock device support for ALC298 platform.
It need to use SSID for the quirk table.
Because IdeaPad also has ALC298 platform.
Use verb for the quirk table will confuse.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 447cae58ce upstream.
The layout of the UAC2 Control request and response varies depending on
the request type. With the current implementation, only the Layout 2
Parameter Block (with the 2-byte sized RANGE attribute) is handled
properly. For the Control requests with the 1-byte sized RANGE attribute
(Bass Control, Mid Control, Tremble Control), the response is parsed
incorrectly.
This commit:
* fixes the wLength field value in the request
* fixes parsing the range values from the response
Fixes: 23caaf19b1 ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea56fb2823 upstream.
With commit 3cf32d1802 ("mtd: nand: vf610: switch to
mtd_ooblayout_ops") the driver started to use the NAND cores
default large page ooblayout. However, shortly after commit
6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
changed the default layout to the old hamming layout, which is
not what vf610_nfc is using. Specify the default large page
layout explicitly.
Fixes: 6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26d99834f8 upstream.
When a 9p request is successfully flushed, the server is expected to just
mark it as used without sending a 9p reply (ie, without writing data into
the buffer). In this case, virtqueue_get_buf() will return len == 0 and
we must not report a REQ_STATUS_RCVD status to the client, otherwise the
client will erroneously assume the request has not been flushed.
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 900c998168 upstream.
The highest objectid, which is assigned to new inode, is decided at
the time of initializing fs roots. However, in cases where log replay
gets processed, the btree which fs root owns might be changed, so we
have to search it again for the highest objectid, otherwise creating
new inode would end up with -EEXIST.
cc: <stable@vger.kernel.org> v4.4-rc6+
Fixes: f32e48e925 ("Btrfs: Initialize btrfs_root->highest_objectid when loading tree root and subvolume roots")
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8f1bc1493 upstream.
This regression is introduced in
commit 3d48d9810d ("btrfs: Handle uninitialised inode eviction").
There are two problems,
a) it is ->destroy_inode() that does the final free on inode, not
->evict_inode(),
b) clear_inode() must be called before ->evict_inode() returns.
This could end up hitting BUG_ON(inode->i_state != (I_FREEING | I_CLEAR));
in evict() because I_CLEAR is set in clear_inode().
Fixes: commit 3d48d9810d ("btrfs: Handle uninitialised inode eviction")
Cc: <stable@vger.kernel.org> # v4.7-rc6+
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55237a5f24 upstream.
It's possible that btrfs_sync_log() bails out after one of the two
btrfs_write_marked_extents() which convert extent state's state bit into
EXTENT_NEED_WAIT from EXTENT_DIRTY/EXTENT_NEW, however only EXTENT_DIRTY
and EXTENT_NEW are searched by free_log_tree() so that those extent states
with EXTENT_NEED_WAIT lead to memory leak.
cc: <stable@vger.kernel.org>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1846430c24 upstream.
In cases that the whole fs flips into readonly status due to failures in
critical sections, then log tree's blocks are still dirty, and this leads
to a crash during umount time, the crash is about use-after-free,
umount
-> close_ctree
-> stop workers
-> iput(btree_inode)
-> iput_final
-> write_inode_now
-> ...
-> queue job on stop'd workers
cc: <stable@vger.kernel.org> v3.12+
Fixes: 681ae50917 ("Btrfs: cleanup reserved space when freeing tree log on error")
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c713fb071e upstream.
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection lost problem")
Cc: Stable <stable@vger.kernel.org> # 4.14+
Fix-suggested-by: Pkshih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 724ba8b30b upstream.
When this method is set, the caller expects struct console_font fields
to be properly initialized when it returns. Leave it unset otherwise
nonsensical (leaked kernel stack) values are returned to user space.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cb18db070 upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent display node was also prematurely
freed.
Note that the display and timings node references are never put after a
successful dt-initialisation so the nodes would leak on later probe
deferrals and on driver unbind.
Fixes: b985172b32 ("video: atmel_lcdfb: add device tree suport")
Cc: stable <stable@vger.kernel.org> # 3.13
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac56aa3bc upstream.
Fix child-node lookup during initialisation which was using the wrong
OF-helper and ended up searching the whole device tree depth-first
starting at the parent rather than just matching on its children.
To make things worse, the parent pci node could end up being prematurely
freed as of_find_node_by_name() drops a reference to its first argument.
Any matching child interrupt-controller node was also leaked.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Cc: stable <stable@vger.kernel.org> # 3.18
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
[lorenzo.pieralisi@arm.com: updated commit subject]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e6522c565 upstream.
MIPS_GENERIC selects some options conditional on BIG_ENDIAN which does
not exist.
Replace BIG_ENDIAN with CPU_BIG_ENDIAN which is the correct kconfig
name. Note that BMIPS_GENERIC does the same which confirms that this
patch is needed.
Fixes: eed0eabd12 ("MIPS: generic: Introduce generic DT-based board support")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.9+
Patchwork: https://patchwork.linux-mips.org/patch/18495/
[jhogan@kernel.org: Clean up commit message]
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10a0cd6e49 upstream.
The functions devm_memremap_pages() and devm_memremap_pages_release() use
different ways to calculate the section-aligned amount of memory. The
latter function may use an incorrect size if the memory region is small
but straddles a section border.
Use the same code for both.
Cc: <stable@vger.kernel.org>
Fixes: 5f29a77cd9 ("mm: fix mixed zone detection in devm_memremap_pages")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af27d9403f upstream.
We get a warning about some slow configurations in randconfig kernels:
mm/memory.c:83:2: error: #warning Unfortunate NUMA and NUMA Balancing config, growing page-frame for last_cpupid. [-Werror=cpp]
The warning is reasonable by itself, but gets in the way of randconfig
build testing, so I'm hiding it whenever CONFIG_COMPILE_TEST is set.
The warning was added in 2013 in commit 75980e97da ("mm: fold
page->_last_nid into page->flags where possible").
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06f29cc81f upstream.
In the function __ext4_grp_locked_error(), __save_error_info()
is called to save error info in super block block, but does not sync
that information to disk to info the subsequence fsck after reboot.
This patch writes the error information to disk. After this patch,
I think there is no obvious EXT4 error handle branches which leads to
"Remounting filesystem read-only" will leave the disk partition miss
the subsequence fsck.
Signed-off-by: Zhouyi Zhou <zhouzhouyi@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abbc3f9395 upstream.
This patch fixes a race between the shutdown path and bio completion
handling. In the ext4 direct io path with async io, after submitting a
bio to the block layer, if journal starting fails,
ext4_direct_IO_write() would bail out pretending that the IO
failed. The caller would have had no way of knowing whether or not the
IO was successfully submitted. So instead, we return -EIOCBQUEUED in
this case. Now, the caller knows that the IO was submitted. The bio
completion handler takes care of the error.
Tested: Ran the shutdown xfstest test 461 in loop for over 2 hours across
4 machines resulting in over 400 runs. Verified that the race didn't
occur. Usually the race was seen in about 20-30 iterations.
Signed-off-by: Harshad Shirwadkar <harshads@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f69120ce6c upstream.
Sphinx emits various (26) warnings when building make target 'htmldocs'.
Currently struct definitions contain duplicate documentation, some as
kernel-docs and some as standard c89 comments. We can reduce
duplication while cleaning up the kernel docs.
Move all kernel-docs to right above each struct member. Use the set of
all existing comments (kernel-doc and c89). Add documentation for
missing struct members and function arguments.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b8b580630 upstream.
According to the OPAL docs:
skiboot-5.2.5/doc/opal-api/opal-rtc-read-3.txt
skiboot-5.2.5/doc/opal-api/opal-rtc-write-4.txt
OPAL_HARDWARE may be returned from OPAL_RTC_READ or OPAL_RTC_WRITE and
this indicates either a transient or permanent error.
Prior to this patch, Linux was not dealing with OPAL_HARDWARE being a
permanent error particularly well, in that you could end up in a busy
loop.
This was not too hard to trigger on an AMI BMC based OpenPOWER machine
doing a continuous "ipmitool mc reset cold" to the BMC, the result of
that being that we'd get stuck in an infinite loop in
opal_get_rtc_time().
We now retry a few times before returning the error higher up the
stack.
Fixes: 16b1d26e77 ("rtc/tpo: Driver to support rtc and wakeup on PowerNV platform")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a61b527b4 upstream.
Check the variable that was most recently initialized.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x, y, f, g, e, m;
statement S1,S2,S3,S4;
@@
x = f(...);
if (\(<+...x...+>\&e\)) S1 else S2
(
x = g(...);
|
m = g(...,&x,...);
|
y = g(...);
*if (e)
S3 else S4
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b65865627 upstream.
__unregister_ftrace_function_probe() will incorrectly parse the glob filter
because it resets the search variable that was setup by filter_parse_regex().
Al Viro reported this:
After that call of filter_parse_regex() we could have func_g.search not
equal to glob only if glob started with '!' or '*'. In the former case
we would've buggered off with -EINVAL (not = 1). In the latter we
would've set func_g.search equal to glob + 1, calculated the length of
that thing in func_g.len and proceeded to reset func_g.search back to
glob.
Suppose the glob is e.g. *foo*. We end up with
func_g.type = MATCH_MIDDLE_ONLY;
func_g.len = 3;
func_g.search = "*foo";
Feeding that to ftrace_match_record() will not do anything sane - we
will be looking for names containing "*foo" (->len is ignored for that
one).
Link: http://lkml.kernel.org/r/20180127031706.GE13338@ZenIV.linux.org.uk
Fixes: 3ba0092971 ("ftrace: Introduce ftrace_glob structure")
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ac1dc736b upstream.
Setting si_code to 0 is the same a setting si_code to SI_USER which is definitely
not correct. With si_code set to SI_USER si_pid and si_uid will be copied to
userspace instead of si_addr. Which is very wrong.
So fix this by using a sensible si_code (SEGV_MAPERR) for this failure.
Fixes: b920de1b77 ("mn10300: add the MN10300/AM33 architecture to the kernel")
Cc: David Howells <dhowells@redhat.com>
Cc: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
