[ Upstream commit cf9e6d5dbd ]
The CLK_POL field specifies whether data is sampled on the falling or
rising edge of PCLK, not whether the data lines are active high or low.
Evidence of this can be found in the timing diagram labeled "horizontal
size setting and pixel clock timing".
Fix the setting by checking the correct flag, V4L2_MBUS_PCLK_SAMPLE_RISING.
While at it, reorder the three polarity flag checks so HSYNC and VSYNC
are grouped together.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 249b286171 ]
On Allwinner SoCs, some high memory bandwidth devices do DMA directly
over the memory bus (called MBUS), instead of the system bus. These
devices include the CSI camera sensor interface, video (codec) engine,
display subsystem, etc.. The memory bus has a different addressing
scheme without the DRAM starting offset.
Deal with this using the "interconnects" property from the device tree,
or if that is not available, set dev->dma_pfn_offset to PHYS_PFN_OFFSET.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1451d5ae35 ]
This driver supports both the mt9v032 (color) and the mt9v022 (mono)
sensors. Depending on which sensor is used, the format from the sensor is
different. The format.code inside the dev struct holds this information.
The enum mbus and enum frame sizes need to take into account both type of
sensors, not just the color one. To solve this, use the format.code in
these functions instead of the hardcoded bayer color format (which is only
used for mt9v032).
[Sakari Ailus: rewrapped commit message]
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e3df204f9 ]
The variable _rate is by ov5640_compute_sys_clk() which returns
zero if the PLL exceeds 1GHz. Unfortunately, the check to see
if the max PLL1 output is checking 'rate' and not '_rate' and
'rate' does not ever appear to be 0.
This patch changes the check against the returned value of
'_rate' to determine if the PLL1 output exceeds 1GHz.
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ab987c42 ]
We can have two cases, when it comes to "zap" fw. Either the fw
requires zap fw to take the GPU out of secure mode at boot, or it does
not and we can write RBBM_SECVID_TRUST_CNTL directly. Previously we
decided based on whether zap fw load succeeded, but this is not a great
plan because:
1) we could have zap fw in the filesystem on a device where it is not
required
2) we could have the inverse case
Instead, shift to deciding based on whether we have a 'zap-shader' node
in dt. In practice, there is only one device (currently) with upstream
dt that does not use zap (cheza), and it already has a /delete-node/ for
the zap-shader node.
Fixes: abccb9fe32 ("drm/msm/a6xx: Add zap shader load")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ce18249af ]
When configuring the frame memory window, the last column and row
numbers are written to the column resp. page address registers. These
numbers are thus one less than the actual window width resp. height.
While this is handled correctly in mipi_dbi_fb_dirty() since commit
03ceb1c8df ("drm/tinydrm: Fix setting of the column/page end
addresses."), it is not in mipi_dbi_blank(). The latter still forgets
to subtract one when calculating the most significant bytes of the
column and row numbers, thus programming wrong values when the display
width or height is a multiple of 256.
Fixes: 02dd95fe31 ("drm/tinydrm: Add MIPI DBI support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230130604.31006-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit def97da136 ]
Commit f92b070f2d ("printk: Do not miss new messages when replaying
the log") introduced a new variable @exclusive_console_stop_seq to
store when an exclusive console should stop printing. It should be
set to the @console_seq value at registration. However, @console_seq
is previously set to @syslog_seq so that the exclusive console knows
where to begin. This results in the exclusive console immediately
reactivating all the other consoles and thus repeating the messages
for those consoles.
Set @console_seq after @exclusive_console_stop_seq has stored the
current @console_seq value.
Fixes: f92b070f2d ("printk: Do not miss new messages when replaying the log")
Link: http://lkml.kernel.org/r/20191219115322.31160-1-john.ogness@linutronix.de
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b1cb1f03 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.
Fix this by:
- Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
configures the combined "CTX0&CTX1" output signal,
- Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
the shared "CRX0/CRX1" input signal, which is fed to both CAN
inputs,
- Adding the missing function GPIO definition for "CTX0&CTX1" to
pinmux_func_gpios[],
- Moving all CAN enums next to each other.
See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
[1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
Version),
[2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
Version,
[3] Table 1.4 List of Pins,
[4] Figure 20.29 Connection Example when Using This Module as 1-Channel
Module (64 Mailboxes x 1 Channel),
[5] Table 32.10 Multiplexed Pins (Port J),
[6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).
Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26a2c2ddc ]
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d61fe22c2a ]
A design of ALSA control core allows applications to execute three
operations for TLV feature; read, write and command. Furthermore, it
allows driver developers to process the operations by two ways; allocated
array or callback function. In the former, read operation is just allowed,
thus developers uses the latter when device driver supports variety of
models or the target model is expected to dynamically change information
stored in TLV container.
The core also allows applications to lock any element so that the other
applications can't perform write operation to the element for element
value and TLV information. When the element is locked, write and command
operation for TLV information are prohibited as well as element value.
Any read operation should be allowed in the case.
At present, when an element has callback function for TLV information,
TLV read operation returns EPERM if the element is locked. On the
other hand, the read operation is success when an element has allocated
array for TLV information. In both cases, read operation is success for
element value expectedly.
This commit fixes the bug. This change can be backported to v4.14
kernel or later.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20191223093347.15279-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 697529091a ]
Before commit bb29b9cccd ("leds: pca963x: Add bindings to invert
polarity") Mode register 2 was initialized directly with either 0x01
or 0x05 for open-drain or totem pole (push-pull) configuration.
Afterwards, MODE2 initialization started using bitwise operations on
top of the default MODE2 register value (0x05). Using bitwise OR for
setting OUTDRV with 0x01 and 0x05 does not produce correct results.
When open-drain is used, instead of setting OUTDRV to 0, the driver
keeps it as 1:
Open-drain: 0x05 | 0x01 -> 0x05 (0b101 - incorrect)
Totem pole: 0x05 | 0x05 -> 0x05 (0b101 - correct but still wrong)
Now OUTDRV setting uses correct bitwise operations for initialization:
Open-drain: 0x05 & ~0x04 -> 0x01 (0b001 - correct)
Totem pole: 0x05 | 0x04 -> 0x05 (0b101 - correct)
Additional MODE2 register definitions are introduced now as well.
Fixes: bb29b9cccd ("leds: pca963x: Add bindings to invert polarity")
Signed-off-by: Zahari Petkov <zahari@balena.io>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec5b356c58 ]
[why]
Up to 4 ODM memory pieces are required per ODM combine and cannot
overlap, i.e. each ODM "session" has to use its own memory pieces.
The ODM-memory mapping is currently broken for generic case.
The maximum number of memory pieces is ASIC-dependent, but it's always
big enough to satisfy maximum number of ODM combines. Memory pieces
are mapped as a bit-map, i.e. one memory piece corresponds to one bit.
The OPTC doing ODM needs to select memory pieces by setting the
corresponding bits, making sure there's no overlap with other OPTC
instances that might be doing ODM.
The current mapping works only for OPTC instance indexes smaller than
3. For instance indexes 3 and up it practically maps no ODM memory,
causing black, gray or white screen in display configs that include
ODM on OPTC instance 3 or up.
[how]
Statically map two unique ODM memory pieces for each OPTC instance
and piece them together when programming ODM combine mode.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8bf2aeb65 ]
The number of possible devfns is 256, but pci_add_dma_alias() allocated a
bitmap of size 255. Fix this off-by-one error.
This fixes commits 338c3149a2 ("PCI: Add support for multiple DMA
aliases") and c663579273 ("PCI: Allocate dma_alias_mask with
bitmap_zalloc()"), but I doubt it was possible to see a problem because
it takes 4 64-bit longs (or 8 32-bit longs) to hold 255 bits, and
bitmap_zalloc() doesn't save the 255-bit size anywhere.
[bhelgaas: commit log, move #define to drivers/pci/pci.h, include loop
limit fix from Qian Cai:
https://lore.kernel.org/r/20191218170004.5297-1-cai@lca.pw]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 216b44000a ]
The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
error: dereferencing freed memory 'pkt'
It looks like there was supposed to be a continue after we free "pkt".
Fixes: 4754fceeb9 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cc509aa83 ]
In the implementation of brcmf_p2p_create_p2pdev() the allocated memory
for p2p_vif is leaked when the mac address is the same as primary
interface. To fix this, go to error path to release p2p_vif via
brcmf_free_vif().
Fixes: cb746e4783 ("brcmfmac: check p2pdev mac address uniqueness")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45178ac0ce ]
Paul reported a very sporadic, rcutorture induced, workqueue failure.
When the planets align, the workqueue rescuer's self-migrate fails and
then triggers a WARN for running a work on the wrong CPU.
Tejun then figured that set_cpus_allowed_ptr()'s stop_one_cpu() call
could be ignored! When stopper->enabled is false, stop_machine will
insta complete the work, without actually doing the work. Worse, it
will not WARN about this (we really should fix this).
It turns out there is a small window where a freshly online'ed CPU is
marked 'online' but doesn't yet have the stopper task running:
BP AP
bringup_cpu()
__cpu_up(cpu, idle) --> start_secondary()
...
cpu_startup_entry()
bringup_wait_for_ap()
wait_for_ap_thread() <-- cpuhp_online_idle()
while (1)
do_idle()
... available to run kthreads ...
stop_machine_unpark()
stopper->enable = true;
Close this by moving the stop_machine_unpark() into
cpuhp_online_idle(), such that the stopper thread is ready before we
start the idle loop and schedule.
Reported-by: "Paul E. McKenney" <paulmck@kernel.org>
Debugged-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: "Paul E. McKenney" <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8488a4180 ]
Some meson pll registers can be initialized with 0 as N value, introducing
the following division by 0 when computing rate :
UBSAN: Undefined behaviour in drivers/clk/meson/clk-pll.c:75:9
division by zero
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc3-608075-g86c9af8630e1-dirty #400
Call trace:
dump_backtrace+0x0/0x1c0
show_stack+0x14/0x20
dump_stack+0xc4/0x100
ubsan_epilogue+0x14/0x68
__ubsan_handle_divrem_overflow+0x98/0xb8
__pll_params_to_rate+0xdc/0x140
meson_clk_pll_recalc_rate+0x278/0x3a0
__clk_register+0x7c8/0xbb0
devm_clk_hw_register+0x54/0xc0
meson_eeclkc_probe+0xf4/0x1a0
platform_drv_probe+0x54/0xd8
really_probe+0x16c/0x438
driver_probe_device+0xb0/0xf0
device_driver_attach+0x94/0xa0
__driver_attach+0x70/0x108
bus_for_each_dev+0xd8/0x128
driver_attach+0x30/0x40
bus_add_driver+0x1b0/0x2d8
driver_register+0xbc/0x1d0
__platform_driver_register+0x78/0x88
axg_driver_init+0x18/0x20
do_one_initcall+0xc8/0x24c
kernel_init_freeable+0x2b0/0x344
kernel_init+0x10/0x128
ret_from_fork+0x10/0x18
This checks if N is null before doing the division.
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
[jbrunet@baylibre.com: update the comment in above the fix]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11e0e167d0 ]
Currently if the allocation of new_buf fails then a null pointer
dereference occurs when assiging new_buf->vb. Avoid this by returning
early on a memory allocation failure as there is not much more can
be done at this point.
Addresses-Coverity: ("Dereference null return")
Fixes: 3e7f51bd96 ("media: meson: add v4l2 m2m video decoder driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47501f87c6 ]
The previous preallocation and DIO decision like below.
allow_outplace_dio !allow_outplace_dio
f2fs_force_buffered_io (*) No_Prealloc / Buffered_IO Prealloc / Buffered_IO
!f2fs_force_buffered_io No_Prealloc / DIO Prealloc / DIO
But, Javier reported Case (*) where zoned device bypassed preallocation but
fell back to buffered writes in f2fs_direct_IO(), resulting in stale data
being read.
In order to fix the issue, actually we need to preallocate blocks whenever
we fall back to buffered IO like this. No change is made in the other cases.
allow_outplace_dio !allow_outplace_dio
f2fs_force_buffered_io (*) Prealloc / Buffered_IO Prealloc / Buffered_IO
!f2fs_force_buffered_io No_Prealloc / DIO Prealloc / DIO
Reported-and-tested-by: Javier Gonzalez <javier@javigon.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cf539a87a ]
This fixes a data-race where `atomic_t dynticks` is copied by value. The
copy is performed non-atomically, resulting in a data-race if `dynticks`
is updated concurrently.
This data-race was found with KCSAN:
==================================================================
BUG: KCSAN: data-race in dyntick_save_progress_counter / rcu_irq_enter
write to 0xffff989dbdbe98e0 of 4 bytes by task 10 on cpu 3:
atomic_add_return include/asm-generic/atomic-instrumented.h:78 [inline]
rcu_dynticks_snap kernel/rcu/tree.c:310 [inline]
dyntick_save_progress_counter+0x43/0x1b0 kernel/rcu/tree.c:984
force_qs_rnp+0x183/0x200 kernel/rcu/tree.c:2286
rcu_gp_fqs kernel/rcu/tree.c:1601 [inline]
rcu_gp_fqs_loop+0x71/0x880 kernel/rcu/tree.c:1653
rcu_gp_kthread+0x22c/0x3b0 kernel/rcu/tree.c:1799
kthread+0x1b5/0x200 kernel/kthread.c:255
<snip>
read to 0xffff989dbdbe98e0 of 4 bytes by task 154 on cpu 7:
rcu_nmi_enter_common kernel/rcu/tree.c:828 [inline]
rcu_irq_enter+0xda/0x240 kernel/rcu/tree.c:870
irq_enter+0x5/0x50 kernel/softirq.c:347
<snip>
Reported by Kernel Concurrency Sanitizer on:
CPU: 7 PID: 154 Comm: kworker/7:1H Not tainted 5.3.0+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Workqueue: kblockd blk_mq_run_work_fn
==================================================================
Signed-off-by: Marco Elver <elver@google.com>
Cc: Paul E. McKenney <paulmck@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: rcu@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd6bc19d76 ]
Tasks waiting within exp_funnel_lock() for an expedited grace period to
elapse can be starved due to the following sequence of events:
1. Tasks A and B both attempt to start an expedited grace
period at about the same time. This grace period will have
completed when the lower four bits of the rcu_state structure's
->expedited_sequence field are 0b'0100', for example, when the
initial value of this counter is zero. Task A wins, and thus
does the actual work of starting the grace period, including
acquiring the rcu_state structure's .exp_mutex and sets the
counter to 0b'0001'.
2. Because task B lost the race to start the grace period, it
waits on ->expedited_sequence to reach 0b'0100' inside of
exp_funnel_lock(). This task therefore blocks on the rcu_node
structure's ->exp_wq[1] field, keeping in mind that the
end-of-grace-period value of ->expedited_sequence (0b'0100')
is shifted down two bits before indexing the ->exp_wq[] field.
3. Task C attempts to start another expedited grace period,
but blocks on ->exp_mutex, which is still held by Task A.
4. The aforementioned expedited grace period completes, so that
->expedited_sequence now has the value 0b'0100'. A kworker task
therefore acquires the rcu_state structure's ->exp_wake_mutex
and starts awakening any tasks waiting for this grace period.
5. One of the first tasks awakened happens to be Task A. Task A
therefore releases the rcu_state structure's ->exp_mutex,
which allows Task C to start the next expedited grace period,
which causes the lower four bits of the rcu_state structure's
->expedited_sequence field to become 0b'0101'.
6. Task C's expedited grace period completes, so that the lower four
bits of the rcu_state structure's ->expedited_sequence field now
become 0b'1000'.
7. The kworker task from step 4 above continues its wakeups.
Unfortunately, the wake_up_all() refetches the rcu_state
structure's .expedited_sequence field:
wake_up_all(&rnp->exp_wq[rcu_seq_ctr(rcu_state.expedited_sequence) & 0x3]);
This results in the wakeup being applied to the rcu_node
structure's ->exp_wq[2] field, which is unfortunate given that
Task B is instead waiting on ->exp_wq[1].
On a busy system, no harm is done (or at least no permanent harm is done).
Some later expedited grace period will redo the wakeup. But on a quiet
system, such as many embedded systems, it might be a good long time before
there was another expedited grace period. On such embedded systems,
this situation could therefore result in a system hang.
This issue manifested as DPM device timeout during suspend (which
usually qualifies as a quiet time) due to a SCSI device being stuck in
_synchronize_rcu_expedited(), with the following stack trace:
schedule()
synchronize_rcu_expedited()
synchronize_rcu()
scsi_device_quiesce()
scsi_bus_suspend()
dpm_run_callback()
__device_suspend()
This commit therefore prevents such delays, timeouts, and hangs by
making rcu_exp_wait_wake() use its "s" argument consistently instead of
refetching from rcu_state.expedited_sequence.
Fixes: 3b5f668e71 ("rcu: Overlap wakeups with next expedited grace period")
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 610dea36d3 ]
Commit 18cd8c93e6 ("rcu/nocb: Print gp/cb kthread hierarchy if
dump_tree") added print statements to rcu_organize_nocb_kthreads for
debugging, but incorrectly guarded them, causing the function to always
spew out its message.
This patch fixes it by guarding both pr_alert statements with dump_tree,
while also changing the second pr_alert to a pr_cont, to print the
hierarchy in a single line (assuming that's how it was supposed to
work).
Fixes: 18cd8c93e6 ("rcu/nocb: Print gp/cb kthread hierarchy if dump_tree")
Signed-off-by: Stefan Reiter <stefan@pimaker.at>
[ paulmck: Make single-nocbs-CPU GP kthreads look less erroneous. ]
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbe3ad61dc ]
A coccicheck run provided information like the following.
drivers/gpu/drm/qxl/qxl_kms.c:295:1-7: ERROR: missing iounmap;
ioremap on line 178 and execution via conditional on line 185
Generated by: scripts/coccinelle/free/iounmap.cocci
A jump target was specified in an if branch. The corresponding function
call did not release the desired system resource then.
Thus use the label “rom_unmap” instead to fix the exception handling
for this function implementation.
Fixes: 5043348a49 ("drm: qxl: Fix error handling at qxl_device_init")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: http://patchwork.freedesktop.org/patch/msgid/5e5ef9c4-4d85-3c93-cf28-42cfcb5b0649@web.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b1413f00b ]
There is a check on the retry counter invalid_buf_id_retry that is always
false because invalid_buf_id_retry is initialized to zero on each iteration
of a while-loop. Fix this by initializing the retry counter before the
while-loop starts.
Addresses-Coverity: ("Logically dead code")
Fixes: b4a967b7d0 ("wil6210: reset buff id in status message after completion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8a595a87e ]
When ath10k_qmi_init() fails, the error handling does not free the irq
resources, which causes an issue if we EPROBE_DEFER as we'll attempt to
(re-)register irqs which are already registered.
Fix this by doing a power off since we just powered on the hardware, and
freeing the irqs as error handling.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd1a5e521c ]
psbfb_probe performs an evaluation of the required size from the stolen
GTT memory, but gets it wrong in two distinct ways:
- The resulting size must be page-size-aligned;
- The size to allocate is derived from the surface dimensions, not the fb
dimensions.
When two connectors are connected with different modes, the smallest will
be stored in the fb dimensions, but the size that needs to be allocated must
match the largest (surface) dimensions. This is what is used in the actual
allocation code.
Fix this by correcting the evaluation to conform to the two points above.
It allows correctly switching to 16bpp when one connector is e.g. 1920x1080
and the other is 1024x768.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107153048.843881-1-paul.kocialkowski@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2debf0852 ]
unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_flower' doesn't validate the size of
netlink attribute 'TCA_FLOWER_FLAGS' provided by user: add a proper entry
to fl_policy.
Fixes: 5b33f48842 ("net/flower: Introduce hardware offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1afa3cc90f ]
unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_matchall' doesn't validate the size
of netlink attribute 'TCA_MATCHALL_FLAGS' provided by user: add a proper
entry to mall_policy.
Fixes: b87f7936a9 ("net/sched: Add match-all classifier hw offloading.")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04fb91243a ]
Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f90522591 ]
Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090
After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.
After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
enic_poll_msix_wq->
vnic_cq_service->
enic_wq_service->
netif_wake_subqueue(enic->netdev, q_number)->
test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.
Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad1e03b2b3 ]
The current generic XDP handler skips execution of XDP programs entirely if
an SKB is marked as cloned. This leads to some surprising behaviour, as
packets can end up being cloned in various ways, which will make an XDP
program not see all the traffic on an interface.
This was discovered by a simple test case where an XDP program that always
returns XDP_DROP is installed on a veth device. When combining this with
the Scapy packet sniffer (which uses an AF_PACKET) socket on the sending
side, SKBs reliably end up in the cloned state, causing them to be passed
through to the receiving interface instead of being dropped. A minimal
reproducer script for this is included below.
This patch fixed the issue by simply triggering the existing linearisation
code for cloned SKBs instead of skipping the XDP program execution. This
behaviour is in line with the behaviour of the native XDP implementation
for the veth driver, which will reallocate and copy the SKB data if the SKB
is marked as shared.
Reproducer Python script (requires BCC and Scapy):
from scapy.all import TCP, IP, Ether, sendp, sniff, AsyncSniffer, Raw, UDP
from bcc import BPF
import time, sys, subprocess, shlex
SKB_MODE = (1 << 1)
DRV_MODE = (1 << 2)
PYTHON=sys.executable
def client():
time.sleep(2)
# Sniffing on the sender causes skb_cloned() to be set
s = AsyncSniffer()
s.start()
for p in range(10):
sendp(Ether(dst="aa:aa:aa:aa:aa:aa", src="cc:cc:cc:cc:cc:cc")/IP()/UDP()/Raw("Test"),
verbose=False)
time.sleep(0.1)
s.stop()
return 0
def server(mode):
prog = BPF(text="int dummy_drop(struct xdp_md *ctx) {return XDP_DROP;}")
func = prog.load_func("dummy_drop", BPF.XDP)
prog.attach_xdp("a_to_b", func, mode)
time.sleep(1)
s = sniff(iface="a_to_b", count=10, timeout=15)
if len(s):
print(f"Got {len(s)} packets - should have gotten 0")
return 1
else:
print("Got no packets - as expected")
return 0
if len(sys.argv) < 2:
print(f"Usage: {sys.argv[0]} <skb|drv>")
sys.exit(1)
if sys.argv[1] == "client":
sys.exit(client())
elif sys.argv[1] == "server":
mode = SKB_MODE if sys.argv[2] == 'skb' else DRV_MODE
sys.exit(server(mode))
else:
try:
mode = sys.argv[1]
if mode not in ('skb', 'drv'):
print(f"Usage: {sys.argv[0]} <skb|drv>")
sys.exit(1)
print(f"Running in {mode} mode")
for cmd in [
'ip netns add netns_a',
'ip netns add netns_b',
'ip -n netns_a link add a_to_b type veth peer name b_to_a netns netns_b',
# Disable ipv6 to make sure there's no address autoconf traffic
'ip netns exec netns_a sysctl -qw net.ipv6.conf.a_to_b.disable_ipv6=1',
'ip netns exec netns_b sysctl -qw net.ipv6.conf.b_to_a.disable_ipv6=1',
'ip -n netns_a link set dev a_to_b address aa:aa:aa:aa:aa:aa',
'ip -n netns_b link set dev b_to_a address cc:cc:cc:cc:cc:cc',
'ip -n netns_a link set dev a_to_b up',
'ip -n netns_b link set dev b_to_a up']:
subprocess.check_call(shlex.split(cmd))
server = subprocess.Popen(shlex.split(f"ip netns exec netns_a {PYTHON} {sys.argv[0]} server {mode}"))
client = subprocess.Popen(shlex.split(f"ip netns exec netns_b {PYTHON} {sys.argv[0]} client"))
client.wait()
server.wait()
sys.exit(server.returncode)
finally:
subprocess.run(shlex.split("ip netns delete netns_a"))
subprocess.run(shlex.split("ip netns delete netns_b"))
Fixes: d445516966 ("net: xdp: support xdp generic on virtual devices")
Reported-by: Stepan Horacek <shoracek@redhat.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f6ab0107a4 ]
Define PT_MAX_FULL_LEVELS as PT64_ROOT_MAX_LEVEL, i.e. 5, to fix shadow
paging for 5-level guest page tables. PT_MAX_FULL_LEVELS is used to
size the arrays that track guest pages table information, i.e. using a
"max levels" of 4 causes KVM to access garbage beyond the end of an
array when querying state for level 5 entries. E.g. FNAME(gpte_changed)
will read garbage and most likely return %true for a level 5 entry,
soft-hanging the guest because FNAME(fetch) will restart the guest
instead of creating SPTEs because it thinks the guest PTE has changed.
Note, KVM doesn't yet support 5-level nested EPT, so PT_MAX_FULL_LEVELS
gets to stay "4" for the PTTYPE_EPT case.
Fixes: 855feb6736 ("KVM: MMU: Add 5 level EPT & Shadow page table support.")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57c32ea42f ]
Setting softlimit larger than hardlimit seems meaningless
for disk quota but currently it is allowed. In this case,
there may be a bit of comfusion for users when they run
df comamnd to directory which has project quota.
For example, we set 20M softlimit and 10M hardlimit of
block usage limit for project quota of test_dir(project id 123).
[root@hades mnt_ext4]# repquota -P -a
*** Report for project quotas on device /dev/loop0
Block grace time: 7days; Inode grace time: 7days
Block limits File limits
Project used soft hard grace used soft hard grace
----------------------------------------------------------------------
0 -- 13 0 0 2 0 0
123 -- 10237 20480 10240 5 200 100
The result of df command as below:
[root@hades mnt_ext4]# df -h test_dir
Filesystem Size Used Avail Use% Mounted on
/dev/loop0 20M 10M 10M 50% /home/cgxu/test/mnt_ext4
Even though it looks like there is another 10M free space to use,
if we write new data to diretory test_dir(inherit project id),
the write will fail with errno(-EDQUOT).
After this patch, the df result looks like below.
[root@hades mnt_ext4]# df -h test_dir
Filesystem Size Used Avail Use% Mounted on
/dev/loop0 10M 10M 3.0K 100% /home/cgxu/test/mnt_ext4
Signed-off-by: Chengguang Xu <cgxu519@mykernel.net>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191016022501.760-1-cgxu519@mykernel.net
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c96dceeabf ]
Commit 904cdbd41d ("jbd2: clear dirty flag when revoking a buffer from
an older transaction") set the BH_Freed flag when forgetting a metadata
buffer which belongs to the committing transaction, it indicate the
committing process clear dirty bits when it is done with the buffer. But
it also clear the BH_Mapped flag at the same time, which may trigger
below NULL pointer oops when block_size < PAGE_SIZE.
rmdir 1 kjournald2 mkdir 2
jbd2_journal_commit_transaction
commit transaction N
jbd2_journal_forget
set_buffer_freed(bh1)
jbd2_journal_commit_transaction
commit transaction N+1
...
clear_buffer_mapped(bh1)
ext4_getblk(bh2 ummapped)
...
grow_dev_page
init_page_buffers
bh1->b_private=NULL
bh2->b_private=NULL
jbd2_journal_put_journal_head(jh1)
__journal_remove_journal_head(hb1)
jh1 is NULL and trigger oops
*) Dir entry block bh1 and bh2 belongs to one page, and the bh2 has
already been unmapped.
For the metadata buffer we forgetting, we should always keep the mapped
flag and clear the dirty flags is enough, so this patch pick out the
these buffers and keep their BH_Mapped flag.
Link: https://lore.kernel.org/r/20200213063821.30455-3-yi.zhang@huawei.com
Fixes: 904cdbd41d ("jbd2: clear dirty flag when revoking a buffer from an older transaction")
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cf913e9683 upstream.
This reverts commit 9db9c0cf58.
Setting mode_config.allow_fb_modifiers manually is completely
unnecessary. It is set automatically by drm_universal_plane_init() based
on the fact if modifier list is provided or not. Even more, it breaks
DE2 and DE3 as they don't support any modifiers beside linear. Modifiers
aware applications can be confused by provided empty modifier list - at
least linear modifier should be included, but it's not for DE2 and DE3.
Fixes: 9db9c0cf58 ("drm/sun4i: drv: Allow framebuffer modifiers in mode config")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200126065937.9564-1-jernej.skrabec@siol.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80cc7bb6c1 upstream.
For data collected on machines with front end stalled cycles supported,
such as found on modern AMD CPU families, commit 146540fb54 ("perf
stat: Always separate stalled cycles per insn") introduces a new line in
CSV output with a leading comma that upsets some automated scripts.
Scripts have to use "-e ex_ret_instr" to work around this issue, after
upgrading to a version of perf with that commit.
We could add "if (have_frontend_stalled && !config->csv_sep)" to the not
(total && avg) else clause, to emphasize that CSV users are usually
scripts, and are written to do only what is needed, i.e., they wouldn't
typically invoke "perf stat" without specifying an explicit event list.
But - let alone CSV output - why should users now tolerate a constant
0-reporting extra line in regular terminal output?:
BEFORE:
$ sudo perf stat --all-cpus -einstructions,cycles -- sleep 1
Performance counter stats for 'system wide':
181,110,981 instructions # 0.58 insn per cycle
# 0.00 stalled cycles per insn
309,876,469 cycles
1.002202582 seconds time elapsed
The user would not like to see the now permanent:
"0.00 stalled cycles per insn"
line fixture, as it gives no useful information.
So this patch removes the printing of the zeroed stalled cycles line
altogether, almost reverting the very original commit fb4605ba47
("perf stat: Check for frontend stalled for metrics"), which seems like
it was written to normalize --metric-only column output of common Intel
machines at the time: modern Intel machines have ceased to support the
genericised frontend stalled metrics AFAICT.
AFTER:
$ sudo perf stat --all-cpus -einstructions,cycles -- sleep 1
Performance counter stats for 'system wide':
244,071,432 instructions # 0.69 insn per cycle
355,353,490 cycles
1.001862516 seconds time elapsed
Output behaviour when stalled cycles is indeed measured is not affected
(BEFORE == AFTER):
$ sudo perf stat --all-cpus -einstructions,cycles,stalled-cycles-frontend -- sleep 1
Performance counter stats for 'system wide':
247,227,799 instructions # 0.63 insn per cycle
# 0.26 stalled cycles per insn
394,745,636 cycles
63,194,485 stalled-cycles-frontend # 16.01% frontend cycles idle
1.002079770 seconds time elapsed
Fixes: 146540fb54 ("perf stat: Always separate stalled cycles per insn")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20200207230613.26709-1-kim.phillips@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 307f1cfa26 upstream.
KVM defines the #DB payload as compatible with the 'pending debug
exceptions' field under VMX, not DR6. Mask off bit 12 when applying the
payload to DR6, as it is reserved on DR6 but not the 'pending debug
exceptions' field.
Fixes: f10c729ff9 ("kvm: vmx: Defer setting of DR6 until #DB delivery")
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3543d7ddd5 upstream.
The interrupt map for the FVP's PCI node is missing the
parent-unit-address cells for each of the INTx entries, leading to the
kernel code failing to parse the entries correctly.
Add the missing zero cells, which are pretty useless as far as the GIC
is concerned, but that the spec requires. This allows INTx to be usable
on the model, and VFIO to work correctly.
Fixes: fa083b99eb ("arm64: dts: fast models: Add DTS fo Base RevC FVP")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f6166aaf1 upstream.
Fix display for sec=krb5i which was wrongly interleaved by cruid,
resulting in string "sec=krb5,cruid=<...>i" instead of
"sec=krb5i,cruid=<...>".
Fixes: 96281b9e46 ("smb3: for kerberos mounts display the credential uid used")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf2b012c90 upstream.
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bb ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
