[ Upstream commit 56e69e59751d20993f243fb7dd6991c4e522424c ]
An overflow may occur if the function is called with the last
block and an offset greater than zero. It is necessary to add
a check to avoid this.
Found by Linux Verification Center (linuxtesting.org) with Svace.
[JK: Make test cover also unalloc table freeing]
Link: https://patch.msgid.link/20240620072413.7448-1-r.smirnov@omp.ru
Suggested-by: Jan Kara <jack@suse.com>
Signed-off-by: Roman Smirnov <r.smirnov@omp.ru>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ca27e0c8c13ac50a4acf9cdf77069e2d94a547d ]
When a SOCK_(STREAM|SEQPACKET) socket connect()s to another one, we need
to lock the two sockets to check their states in unix_stream_connect().
We use unix_state_lock() for the server and unix_state_lock_nested() for
client with tricky sk->sk_state check to avoid deadlock.
The possible deadlock scenario are the following:
1) Self connect()
2) Simultaneous connect()
The former is simple, attempt to grab the same lock, and the latter is
AB-BA deadlock.
After the server's unix_state_lock(), we check the server socket's state,
and if it's not TCP_LISTEN, connect() fails with -EINVAL.
Then, we avoid the former deadlock by checking the client's state before
unix_state_lock_nested(). If its state is not TCP_LISTEN, we can make
sure that the client and the server are not identical based on the state.
Also, the latter deadlock can be avoided in the same way. Due to the
server sk->sk_state requirement, AB-BA deadlock could happen only with
TCP_LISTEN sockets. So, if the client's state is TCP_LISTEN, we can
give up the second lock to avoid the deadlock.
CPU 1 CPU 2 CPU 3
connect(A -> B) connect(B -> A) listen(A)
--- --- ---
unix_state_lock(B)
B->sk_state == TCP_LISTEN
READ_ONCE(A->sk_state) == TCP_CLOSE
^^^^^^^^^
ok, will lock A unix_state_lock(A)
.--------------' WRITE_ONCE(A->sk_state, TCP_LISTEN)
| unix_state_unlock(A)
|
| unix_state_lock(A)
| A->sk_sk_state == TCP_LISTEN
| READ_ONCE(B->sk_state) == TCP_LISTEN
v ^^^^^^^^^^
unix_state_lock_nested(A) Don't lock B !!
Currently, while checking the client's state, we also check if it's
TCP_ESTABLISHED, but this is unlikely and can be checked after we know
the state is not TCP_CLOSE.
Moreover, if it happens after the second lock, we now jump to the restart
label, but it's unlikely that the server is not found during the retry,
so the jump is mostly to revist the client state check.
Let's remove the retry logic and check the state against TCP_CLOSE first.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fba8334721e266f92079632598e46e5f89082f30 ]
When all the strides in a WQE have been consumed, the WQE is unlinked
from the WQ linked list (mlx5_wq_ll_pop()). For SHAMPO, it is possible
to receive CQEs with 0 consumed strides for the same WQE even after the
WQE is fully consumed and unlinked. This triggers an additional unlink
for the same wqe which corrupts the linked list.
Fix this scenario by accepting 0 sized consumed strides without
unlinking the WQE again.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240603212219.1037656-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bad28cfc30988a845fb3f59a99f4b8a4ce8fe95 ]
Let the power supply core register the attribute.
This ensures that the attribute is created before the device is
announced to userspace, avoiding a race condition.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a231eed10ed5a290129fda36ad7bcc263c53ff7d ]
Let the power supply core register the attribute.
This ensures that the attribute is created before the device is
announced to userspace, avoid a race condition.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db19d3aa77612983a02bd223b3f273f896b243cf ]
There is a race condition in the CMT interrupt handler. In the interrupt
handler the driver sets a driver private flag, FLAG_IRQCONTEXT. This
flag is used to indicate any call to set_next_event() should not be
directly propagated to the device, but instead cached. This is done as
the interrupt handler itself reprograms the device when needed before it
completes and this avoids this operation to take place twice.
It is unclear why this design was chosen, my suspicion is to allow the
struct clock_event_device.event_handler callback, which is called while
the FLAG_IRQCONTEXT is set, can update the next event without having to
write to the device twice.
Unfortunately there is a race between when the FLAG_IRQCONTEXT flag is
set and later cleared where the interrupt handler have already started to
write the next event to the device. If set_next_event() is called in
this window the value is only cached in the driver but not written. This
leads to the board to misbehave, or worse lockup and produce a splat.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 0-...!: (0 ticks this GP) idle=f5e0/0/0x0 softirq=519/519 fqs=0 (false positive?)
rcu: (detected by 1, t=6502 jiffies, g=-595, q=77 ncpus=2)
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.10.0-rc5-arm64-renesas-00019-g74a6f86eaf1c-dirty #20
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : tick_check_broadcast_expired+0xc/0x40
lr : cpu_idle_poll.isra.0+0x8c/0x168
sp : ffff800081c63d70
x29: ffff800081c63d70 x28: 00000000580000c8 x27: 00000000bfee5610
x26: 0000000000000027 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00007fbb9100 x22: ffff8000818f1008 x21: ffff8000800ef07c
x20: ffff800081c79ec0 x19: ffff800081c70c28 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffc2c717d8
x14: 0000000000000000 x13: ffff000009c18080 x12: ffff8000825f7fc0
x11: 0000000000000000 x10: ffff8000818f3cd4 x9 : 0000000000000028
x8 : ffff800081c79ec0 x7 : ffff800081c73000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : ffff7ffffe286000 x3 : 0000000000000000
x2 : ffff7ffffe286000 x1 : ffff800082972900 x0 : ffff8000818f1008
Call trace:
tick_check_broadcast_expired+0xc/0x40
do_idle+0x9c/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x11c
do_one_initcall+0x0/0x260
__primary_switched+0x80/0x88
rcu: rcu_preempt kthread timer wakeup didn't happen for 6501 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402
rcu: Possible timer handling issue on cpu=0 timer-softirq=262
rcu: rcu_preempt kthread starved for 6502 jiffies! g-595 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:I stack:0 pid:15 tgid:15 ppid:2 flags:0x00000008
Call trace:
__switch_to+0xbc/0x100
__schedule+0x358/0xbe0
schedule+0x48/0x148
schedule_timeout+0xc4/0x138
rcu_gp_fqs_loop+0x12c/0x764
rcu_gp_kthread+0x208/0x298
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
The design have been part of the driver since it was first merged in
early 2009. It becomes increasingly harder to trigger the issue the
older kernel version one tries. It only takes a few boots on v6.10-rc5,
while hundreds of boots are needed to trigger it on v5.10.
Close the race condition by using the CMT channel lock for the two
competing sections. The channel lock was added to the driver after its
initial design.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20240702190230.3825292-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55d4669ef1b76823083caecfab12a8bd2ccdcf64 ]
When rcu_barrier() calls rcu_rdp_cpu_online() and observes a CPU off
rnp->qsmaskinitnext, it means that all accesses from the offline CPU
preceding the CPUHP_TEARDOWN_CPU are visible to RCU barrier, including
callbacks expiration and counter updates.
However interrupts can still fire after stop_machine() re-enables
interrupts and before rcutree_report_cpu_dead(). The related accesses
happening between CPUHP_TEARDOWN_CPU and rnp->qsmaskinitnext clearing
are _NOT_ guaranteed to be seen by rcu_barrier() without proper
ordering, especially when callbacks are invoked there to the end, making
rcutree_migrate_callback() bypass barrier_lock.
The following theoretical race example can make rcu_barrier() hang:
CPU 0 CPU 1
----- -----
//cpu_down()
smpboot_park_threads()
//ksoftirqd is parked now
<IRQ>
rcu_sched_clock_irq()
invoke_rcu_core()
do_softirq()
rcu_core()
rcu_do_batch()
// callback storm
// rcu_do_batch() returns
// before completing all
// of them
// do_softirq also returns early because of
// timeout. It defers to ksoftirqd but
// it's parked
</IRQ>
stop_machine()
take_cpu_down()
rcu_barrier()
spin_lock(barrier_lock)
// observes rcu_segcblist_n_cbs(&rdp->cblist) != 0
<IRQ>
do_softirq()
rcu_core()
rcu_do_batch()
//completes all pending callbacks
//smp_mb() implied _after_ callback number dec
</IRQ>
rcutree_report_cpu_dead()
rnp->qsmaskinitnext &= ~rdp->grpmask;
rcutree_migrate_callback()
// no callback, early return without locking
// barrier_lock
//observes !rcu_rdp_cpu_online(rdp)
rcu_barrier_entrain()
rcu_segcblist_entrain()
// Observe rcu_segcblist_n_cbs(rsclp) == 0
// because no barrier between reading
// rnp->qsmaskinitnext and rsclp->len
rcu_segcblist_add_len()
smp_mb__before_atomic()
// will now observe the 0 count and empty
// list, but too late, we enqueue regardless
WRITE_ONCE(rsclp->len, rsclp->len + v);
// ignored barrier callback
// rcu barrier stall...
This could be solved with a read memory barrier, enforcing the message
passing between rnp->qsmaskinitnext and rsclp->len, matching the full
memory barrier after rsclp->len addition in rcu_segcblist_add_len()
performed at the end of rcu_do_batch().
However the rcu_barrier() is complicated enough and probably doesn't
need too many more subtleties. CPU down is a slowpath and the
barrier_lock seldom contended. Solve the issue with unconditionally
locking the barrier_lock on rcutree_migrate_callbacks(). This makes sure
that either rcu_barrier() sees the empty queue or its entrained
callback will be migrated.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf546dd289e0f6d2594c25e2fb4e19ee67c6d988 ]
If we allocate a bio that is larger than NVMe maximum request size,
attach integrity metadata to it and send it to the NVMe subsystem, the
integrity metadata will be corrupted.
Splitting the bio works correctly. The function bio_split will clone the
bio, trim the iterator of the first bio and advance the iterator of the
second bio.
However, the function rq_integrity_vec has a bug - it returns the first
vector of the bio's metadata and completely disregards the metadata
iterator that was advanced when the bio was split. Thus, the second bio
uses the same metadata as the first bio and this leads to metadata
corruption.
This commit changes rq_integrity_vec, so that it calls mp_bvec_iter_bvec
instead of returning the first vector. mp_bvec_iter_bvec reads the
iterator and uses it to build a bvec for the current position in the
iterator.
The "queue_max_integrity_segments(rq->q) > 1" check was removed, because
the updated rq_integrity_vec function works correctly with multiple
segments.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/49d1afaa-f934-6ed2-a678-e0d428c63a65@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 305a5170dc5cf3d395bb4c4e9239bca6d0b54b49 ]
Currently, mdadm support --revert-reshape to abort the reshape while
reassembling, as the test 07revert-grow. However, following BUG_ON()
can be triggerred by the test:
kernel BUG at drivers/md/raid5.c:6278!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
irq event stamp: 158985
CPU: 6 PID: 891 Comm: md0_reshape Not tainted 6.9.0-03335-g7592a0b0049a #94
RIP: 0010:reshape_request+0x3f1/0xe60
Call Trace:
<TASK>
raid5_sync_request+0x43d/0x550
md_do_sync+0xb7a/0x2110
md_thread+0x294/0x2b0
kthread+0x147/0x1c0
ret_from_fork+0x59/0x70
ret_from_fork_asm+0x1a/0x30
</TASK>
Root cause is that --revert-reshape update the raid_disks from 5 to 4,
while reshape position is still set, and after reassembling the array,
reshape position will be read from super block, then during reshape the
checking of 'writepos' that is caculated by old reshape position will
fail.
Fix this panic the easy way first, by converting the BUG_ON() to
WARN_ON(), and stop the reshape if checkings fail.
Noted that mdadm must fix --revert-shape as well, and probably md/raid
should enhance metadata validation as well, however this means
reassemble will fail and there must be user tools to fix the wrong
metadata.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240611132251.1967786-13-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8768a134518e406d41799a3594aeb74e0889cf7 ]
The deletion of safemode_timer in mddev_suspend() is redundant and
potentially harmful now. If timer is about to be woken up but gets
deleted, 'in_sync' will remain 0 until the next write, causing array
to stay in the 'active' state instead of transitioning to 'clean'.
Commit 0d9f4f135e ("MD: Add del_timer_sync to mddev_suspend (fix
nasty panic))" introduced this deletion for dm, because if timer fired
after dm is destroyed, the resource which the timer depends on might
have been freed.
However, commit 0dd84b3193 ("md: call __md_stop_writes in md_stop")
added __md_stop_writes() to md_stop(), which is called before freeing
resource. Timer is deleted in __md_stop_writes(), and the origin issue
is resolved. Therefore, delete safemode_timer can be removed safely now.
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240508092053.1447930-1-linan666@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6040072f4774a575fa67b912efe7722874be337b ]
On powerpc systems, spinlock acquisition does not order prior stores
against later loads. This means that this statement:
rfcp->rfc_next = NULL;
Can be reordered to follow this statement:
WRITE_ONCE(*rfcpp, rfcp);
Which is then a data race with rcu_torture_fwd_prog_cr(), specifically,
this statement:
rfcpn = READ_ONCE(rfcp->rfc_next)
KCSAN located this data race, which represents a real failure on powerpc.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Marco Elver <elver@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <kasan-dev@googlegroups.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3862093ee93fcfbdadcb7957f5f8974fffa806a ]
bcm_sf2_mdio_register() calls of_phy_find_device() and then
phy_device_remove() in a loop to remove existing PHY devices.
of_phy_find_device() eventually calls bus_find_device(), which calls
get_device() on the returned struct device * to increment the refcount.
The current implementation does not decrement the refcount, which causes
memory leak.
This commit adds the missing phy_device_free() call to decrement the
refcount via put_device() to balance the refcount.
Fixes: 771089c2a4 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806011327.3817861-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5431dc2803ac159d6d4645ae237d15c3cb252db ]
This restores behaviour (including the comment) from now-removed
hci_request.c, and also matches existing code for active scanning.
Without this, the duplicates filter is always active when passive
scanning, which makes it impossible to work with devices that send
nontrivial dynamic data in their advertisement reports.
Fixes: abfeea476c ("Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY")
Signed-off-by: Anton Khirnov <anton@khirnov.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92c4ee25208d0f35dafc3213cdf355fbe449e078 ]
syzbot hit a use-after-free[1] which is caused because the bridge doesn't
make sure that all previous garbage has been collected when removing a
port. What happens is:
CPU 1 CPU 2
start gc cycle remove port
acquire gc lock first
wait for lock
call br_multicasg_gc() directly
acquire lock now but free port
the port can be freed
while grp timers still
running
Make sure all previous gc cycles have finished by using flush_work before
freeing the port.
[1]
BUG: KASAN: slab-use-after-free in br_multicast_port_group_expired+0x4c0/0x550 net/bridge/br_multicast.c:861
Read of size 8 at addr ffff888071d6d000 by task syz.5.1232/9699
CPU: 1 PID: 9699 Comm: syz.5.1232 Not tainted 6.10.0-rc5-syzkaller-00021-g24ca36a562d6 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/07/2024
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:114
print_address_description mm/kasan/report.c:377 [inline]
print_report+0xc3/0x620 mm/kasan/report.c:488
kasan_report+0xd9/0x110 mm/kasan/report.c:601
br_multicast_port_group_expired+0x4c0/0x550 net/bridge/br_multicast.c:861
call_timer_fn+0x1a3/0x610 kernel/time/timer.c:1792
expire_timers kernel/time/timer.c:1843 [inline]
__run_timers+0x74b/0xaf0 kernel/time/timer.c:2417
__run_timer_base kernel/time/timer.c:2428 [inline]
__run_timer_base kernel/time/timer.c:2421 [inline]
run_timer_base+0x111/0x190 kernel/time/timer.c:2437
Reported-by: syzbot+263426984509be19c9a0@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=263426984509be19c9a0
Fixes: e12cec65b5 ("net: bridge: mcast: destroy all entries via gc")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20240802080730.3206303-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3db03fb4995ef85fc41e86262ead7b4852f4bcf0 ]
While x86_64 has PMD aligned text sections, i386 does not have this
luxery. Notably ALIGN_ENTRY_TEXT_END is empty and _etext has PAGE
alignment.
This means that text on i386 can be page granular at the tail end,
which in turn means that the PTI text clones should consistently
account for this.
Make pti_clone_entry_text() consistent with pti_clone_kernel_text().
Fixes: 16a3fe634f ("x86/mm/pti: Clone kernel-image on PTE level for 32 bit")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41e71dbb0e0a0fe214545fe64af031303a08524c ]
Guenter reported dodgy crashes on an i386-nosmp build using GCC-11
that had the form of endless traps until entry stack exhaust and then
#DF from the stack guard.
It turned out that pti_clone_pgtable() had alignment assumptions on
the start address, notably it hard assumes start is PMD aligned. This
is true on x86_64, but very much not true on i386.
These assumptions can cause the end condition to malfunction, leading
to a 'short' clone. Guess what happens when the user mapping has a
short copy of the entry text?
Use the correct increment form for addr to avoid alignment
assumptions.
Fixes: 16a3fe634f ("x86/mm/pti: Clone kernel-image on PTE level for 32 bit")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20240731163105.GG33588@noisy.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 224fa3552029a3d14bec7acf72ded8171d551b88 ]
Per the example of:
!atomic_cmpxchg(&key->enabled, 0, 1)
the inverse was written as:
atomic_cmpxchg(&key->enabled, 1, 0)
except of course, that while !old is only true for old == 0, old is
true for everything except old == 0.
Fix it to read:
atomic_cmpxchg(&key->enabled, 1, 0) == 1
such that only the 1->0 transition returns true and goes on to disable
the keys.
Fixes: 83ab38ef0a0b ("jump_label: Fix concurrency issues in static_key_slow_dec()")
Reported-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lkml.kernel.org/r/20240731105557.GY33588@noisy.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72b96ee29ed6f7670bbb180ba694816e33d361d1 ]
Width of chunk related bitfields is ACTIVATE_SCAN and SCAN_STATUS MSRs
are different in newer IFS generation compared to gen0.
Make changes to scan test flow such that MSRs are populated
appropriately based on the generation supported by hardware.
Account for the 8/16 bit MSR bitfield width differences between gen0 and
newer generations for the scan test trace event too.
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Link: https://lore.kernel.org/r/20231005195137.3117166-5-jithu.joseph@intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Stable-dep-of: 3114f77e9453 ("platform/x86/intel/ifs: Initialize union ifs_status to zero")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6be6cba9c4371d27f78d900ccfe34bb880d9ee20 ]
The mbigen interrupt chip has its per node registers located in a
contiguous region of page sized chunks. The code maps them into virtual
address space as a contiguous region and determines the address of a node
by using the node ID as index.
mbigen chip
|-----------------|------------|--------------|
mgn_node_0 mgn_node_1 ... mgn_node_i
|--------------| |--------------| |----------------------|
[0x0000, 0x0x0FFF] [0x1000, 0x1FFF] [i*0x1000, (i+1)*0x1000 - 1]
This works correctly up to 10 nodes, but then fails because the 11th's
array slot is used for the MGN_CLEAR registers.
mbigen chip
|-----------|--------|--------|---------------|--------|
mgn_node_0 mgn_node_1 ... mgn_clear_register ... mgn_node_i
|-----------------|
[0xA000, 0xAFFF]
Skip the MGN_CLEAR register space when calculating the offset for node IDs
greater than or equal to ten.
Fixes: a6c2f87b88 ("irqchip/mbigen: Implement the mbigen irq chip operation functions")
Signed-off-by: Yipeng Zou <zouyipeng@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240730014400.1751530-1-zouyipeng@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1193d9bbbd379defe9be3c6de566de684de8a6f ]
Flushing list in cancel_gc drops references to other lists right away,
without waiting for RCU to destroy list. Fixes race when referenced
ipsets can't be destroyed while referring list is scheduled for destroy.
Fixes: 97f7cf1cd80e ("netfilter: ipset: fix performance regression in swap operation")
Signed-off-by: Alexander Maltsev <keltar.gw@gmail.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7c70bcc2a84cf925f655ea1ac4b8088062b144a3 upstream.
In main_loop_s function, when the open(cfg_input, O_RDONLY) function is
run, the last fd is not closed if the "--cfg_repeat > 0" branch is not
taken.
Fixes: 05be5e273c ("selftests: mptcp: add disconnect tests")
Cc: stable@vger.kernel.org
Signed-off-by: Liu Jing <liujing@cmss.chinamobile.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68cc924729ffcfe90d0383177192030a9aeb2ee4 upstream.
When a subflow receives and discards duplicate data, the mptcp
stack assumes that the consumed offset inside the current skb is
zero.
With multiple subflows receiving data simultaneously such assertion
does not held true. As a result the subflow-level copied_seq will
be incorrectly increased and later on the same subflow will observe
a bad mapping, leading to subflow reset.
Address the issue taking into account the skb consumed offset in
mptcp_subflow_discard_data().
Fixes: 04e4cd4f7c ("mptcp: cleanup mptcp_subflow_discard_data()")
Cc: stable@vger.kernel.org
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/501
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4258b94831bb7ff28ab80e3c8d94db37db930728 upstream.
The 'backup' flag from mptcp_subflow_context structure is supposed to be
set only when the other peer flagged a subflow as backup, not the
opposite.
Fixes: 067065422f ("mptcp: add the outgoing MP_PRIO support")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a567c2a10033bf04ed618368d179bce6977984b upstream.
Since its introduction, the mentioned MIB accounted for the wrong
event: wake-up being skipped as not-needed on some edge condition
instead of incoming skb being dropped after landing in the (subflow)
receive queue.
Move the increment in the correct location.
Fixes: ce599c5163 ("mptcp: properly account bulk freed memory")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b317e0eb287bd30a1b329513531157c25e8b692 upstream.
Currently the per connection announced address counter is never
decreased. As a consequence, after connection establishment, if
the NL PM deletes an endpoint and adds a new/different one, no
additional subflow is created for the new endpoint even if the
current limits allow that.
Address the issue properly updating the signaled address counter
every time the NL PM removes such addresses.
Fixes: 01cacb00b3 ("mptcp: add netlink-based PM")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efd340bf3d7779a3a8ec954d8ec0fb8a10f24982 upstream.
When sending an MP_JOIN + SYN + ACK, it is possible to mark the subflow
as 'backup' by setting the flag with the same name. Before this patch,
the backup was set if the other peer set it in its MP_JOIN + SYN
request.
It is not correct: the backup flag should be set in the MPJ+SYN+ACK only
if the host asks for it, and not mirroring what was done by the other
peer. It is then required to have a dedicated bit for each direction,
similar to what is done in the subflow context.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 167b93258d1e2230ee3e8a97669b4db4cc9e90aa upstream.
Currently the per-connection announced address counter is never
decreased. When the user-space PM is in use, this just affect
the information exposed via diag/sockopt, but it could still foul
the PM to wrong decision.
Add the missing accounting for the user-space PM's sake.
Fixes: 8b1c94da1e ("mptcp: only send RM_ADDR in nl_cmd_remove")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08f3a5c38087d1569e982a121aad1e6acbf145ce upstream.
It could lead to error happen because the variable res is not updated if
the call to sr_share_read_word returns an error. In this particular case
error code was returned and res stayed uninitialized. Same issue also
applies to sr_read_reg.
This can be avoided by checking the return value of sr_share_read_word
and sr_read_reg, and propagating the error if the read operation failed.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b511572660190db1dc8ba412efd0be0d3781ab6 upstream.
On the off chance that clock value ends up being too high (by means
of skl_ddi_calculate_wrpll() having been called with big enough
value of crtc_state->port_clock * 1000), one possible consequence
may be that the result will not be able to fit into signed int.
Fix this issue by moving conversion of clock parameter from kHz to Hz
into the body of skl_ddi_calculate_wrpll(), as well as casting the
same parameter to u64 type while calculating the value for AFE clock.
This both mitigates the overflow problem and avoids possible erroneous
integer promotion mishaps.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 82d3543701 ("drm/i915/skl: Implementation of SKL DPLL programming")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729174035.25727-1-n.zhandarovich@fintech.ru
(cherry picked from commit 833cf12846aa19adf9b76bc79c40747726f3c0c1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e58337100721f3cc0c7424a18730e4f39844934f upstream.
Introduce a version of the fence ops that on release doesn't remove
the fence from the pending list, and thus doesn't require a lock to
fix poll->fence wait->fence unref deadlocks.
vmwgfx overwrites the wait callback to iterate over the list of all
fences and update their status, to do that it holds a lock to prevent
the list modifcations from other threads. The fence destroy callback
both deletes the fence and removes it from the list of pending
fences, for which it holds a lock.
dma buf polling cb unrefs a fence after it's been signaled: so the poll
calls the wait, which signals the fences, which are being destroyed.
The destruction tries to acquire the lock on the pending fences list
which it can never get because it's held by the wait from which it
was called.
Old bug, but not a lot of userspace apps were using dma-buf polling
interfaces. Fix those, in particular this fixes KDE stalls/deadlock.
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Fixes: 2298e804e9 ("drm/vmwgfx: rework to new fence interface, v2")
Cc: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.2+
Reviewed-by: Maaz Mombasawala <maaz.mombasawala@broadcom.com>
Reviewed-by: Martin Krastev <martin.krastev@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722184313.181318-2-zack.rusin@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dab73ab925a51ab05543b491bf17463a48ca323 upstream.
Commit 7ba5ca32fe ("ALSA: firewire-lib: operate for period elapse event
in process context") removed the process context workqueue from
amdtp_domain_stream_pcm_pointer() and update_pcm_pointers() to remove
its overhead.
With RME Fireface 800, this lead to a regression since
Kernels 5.14.0, causing an AB/BA deadlock competition for the
substream lock with eventual system freeze under ALSA operation:
thread 0:
* (lock A) acquire substream lock by
snd_pcm_stream_lock_irq() in
snd_pcm_status64()
* (lock B) wait for tasklet to finish by calling
tasklet_unlock_spin_wait() in
tasklet_disable_in_atomic() in
ohci_flush_iso_completions() of ohci.c
thread 1:
* (lock B) enter tasklet
* (lock A) attempt to acquire substream lock,
waiting for it to be released:
snd_pcm_stream_lock_irqsave() in
snd_pcm_period_elapsed() in
update_pcm_pointers() in
process_ctx_payloads() in
process_rx_packets() of amdtp-stream.c
? tasklet_unlock_spin_wait
</NMI>
<TASK>
ohci_flush_iso_completions firewire_ohci
amdtp_domain_stream_pcm_pointer snd_firewire_lib
snd_pcm_update_hw_ptr0 snd_pcm
snd_pcm_status64 snd_pcm
? native_queued_spin_lock_slowpath
</NMI>
<IRQ>
_raw_spin_lock_irqsave
snd_pcm_period_elapsed snd_pcm
process_rx_packets snd_firewire_lib
irq_target_callback snd_firewire_lib
handle_it_packet firewire_ohci
context_tasklet firewire_ohci
Restore the process context work queue to prevent deadlock
AB/BA deadlock competition for ALSA substream lock of
snd_pcm_stream_lock_irq() in snd_pcm_status64()
and snd_pcm_stream_lock_irqsave() in snd_pcm_period_elapsed().
revert commit 7ba5ca32fe ("ALSA: firewire-lib: operate for period
elapse event in process context")
Replace inline description to prevent future deadlock.
Cc: stable@vger.kernel.org
Fixes: 7ba5ca32fe ("ALSA: firewire-lib: operate for period elapse event in process context")
Reported-by: edmund.raile <edmund.raile@proton.me>
Closes: https://lore.kernel.org/r/kwryofzdmjvzkuw6j3clftsxmoolynljztxqwg76hzeo4simnl@jn3eo7pe642q/
Signed-off-by: Edmund Raile <edmund.raile@protonmail.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240730195318.869840-3-edmund.raile@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6a66e521a2032f7fcba2af5a9bcbaeaa19b7ca3 upstream.
The 'mptcp_subflow_context' structure has two items related to the
backup flags:
- 'backup': the subflow has been marked as backup by the other peer
- 'request_bkup': the backup flag has been set by the host
Before this patch, the scheduler was only looking at the 'backup' flag.
That can make sense in some cases, but it looks like that's not what we
wanted for the general use, because either the path-manager was setting
both of them when sending an MP_PRIO, or the receiver was duplicating
the 'backup' flag in the subflow request.
Note that the use of these two flags in the path-manager are going to be
fixed in the next commits, but this change here is needed not to modify
the behaviour.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa37bde1a7b645816cda8b80df4753ecf172bf1 upstream.
both callers have verified that fd is not greater than ->max_fds;
however, misprediction might end up with
tofree = fdt->fd[fd];
being speculatively executed. That's wrong for the same reasons
why it's wrong in close_fd()/file_close_fd_locked(); the same
solution applies - array_index_nospec(fd, fdt->max_fds) could differ
from fd only in case of speculative execution on mispredicted path.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cd44dd1d17a23d5cc8c443c659ca57aa76e2fa5 upstream.
When btrfs makes a block group read-only, it adds all free regions in the
block group to space_info->bytes_readonly. That free space excludes
reserved and pinned regions. OTOH, when btrfs makes the block group
read-write again, it moves all the unused regions into the block group's
zone_unusable. That unused region includes reserved and pinned regions.
As a result, it counts too much zone_unusable bytes.
Fortunately (or unfortunately), having erroneous zone_unusable does not
affect the calculation of space_info->bytes_readonly, because free
space (num_bytes in btrfs_dec_block_group_ro) calculation is done based on
the erroneous zone_unusable and it reduces the num_bytes just to cancel the
error.
This behavior can be easily discovered by adding a WARN_ON to check e.g,
"bg->pinned > 0" in btrfs_dec_block_group_ro(), and running fstests test
case like btrfs/282.
Fix it by properly considering pinned and reserved in
btrfs_dec_block_group_ro(). Also, add a WARN_ON and introduce
btrfs_space_info_update_bytes_zone_unusable() to catch a similar mistake.
Fixes: 169e0da91a ("btrfs: zoned: track unusable bytes for zones")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
