Remove support for gpio_disable_free() because it is called when the libgpiod
command "gpioset" is invoked. This gives the GPIO control back to hardware which
cancels out the effort to set the GPIO value.
Reminder of the code flow to change a GPIO value from software:
1) All GPIOs are controlled by hardware by default
2) To change the GPIO value, enable software control via a mux.
3) Once software has control over the GPIO pin, the gpio-mlxbf3 driver
will be able to change the direction and value of the GPIO.
When the user runs "gpioset gpiochip0 0=0" for example, the gpio
pin value should change from 1 to 0. In this case, mlxbf3_gpio_request_enable()
is called via gpiochip_generic_request(). The latter switches GPIO control from
hardware to software. Then the GPIO value is changed from 1 to 0. However,
gpio_disable_free() is also called which changes control back to hardware
which changes the GPIO value back to 1.
Fixes: d11f932808 ("pinctrl: mlxbf3: Add pinctrl driver support")
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230818164314.8505-2-asmaa@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed pinctrl bindings are missing an additionalProperties/
unevaluatedProperties schemas on the child pin mux nodes which means any
undefined properties are allowed. In addition, using
'additionalProperties' for child nodes with any name works better than a
pattern matching everything with an if/then schema to select nodes only.
With 'additionalProperties' added, 'pins' and 'bias-disable'
properties need to be added as they were not defined. A $ref to
pinmux-node.yaml which defines the common property types was also
missing.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819010907.916061-1-robh@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Qualcomm pinctrl changes for v6.6
1. Add support for the SM6115 and SM8350 LPASS (Low Power Audio
SubSystem) TLMM pin controllers.
2. Add bindings for the Qualcomm PMC8180 and PMC8180C PMICs GPIO pin
controllers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In atmel_conf_pin_config_dbg_show(), checking atmel_pioctrl->pins[pin_id]
against being NULL doesn't make any sense as it gets derefenced first and
the driver's probe() method immediately returns -ENOMEM when devm_kzalloc()
returns NULL for any atmel_pioctrl->pins[] element anyway, thus failing to
register the device...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/4ab2f59f-45c1-76a2-94da-3331e8ec4e35@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update binding for yaml and remove the old related txt bindings. Note that
we are also adding the undocumented pinctrl-single,slew-rate property. And
we only use the first example from the old binding.
As we are mostly using a generic compatible across various SoCs, let's not
start adding matches for random pin group node naming. Let's standardize on
pin group node name ending in -pins with an optional instance number
suffix.
As a pin group may have additional pins added to it later on, let's always
use -pins rather than -pin for the gropu name.
Most of the dts files have been updated already for the pin group node
names with a few changes still pending.
Cc: Nishanth Menon <nm@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230721082654.27036-1-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support to handle 'output-enable' and 'bias-high-impedance'
configurations.
Using these pinctrl properties observed hang issues with older PMUFW(Xilinx
ZynqMP Platform Management Firmware), hence reverted the patch.
Commit 9989bc33c4 ("Revert "pinctrl: pinctrl-zynqmp: Add support
for output-enable and bias-high-impedance"").
Support for configuring these properties added in PMUFW Configuration Set
version 2.0. When there is a request for these configurations from pinctrl
driver for ZynqMP platform, xilinx firmware driver checks for this version
before configuring these properties to avoid the hang issue and proceeds
further only when firmware version is >=2 otherwise it returns error.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230731095026.3766675-5-sai.krishna.potthuri@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add 'output-enable' configuration parameter to the properties list.
Using these pinctrl properties observed hang issues with older Xilinx
ZynqMP Platform Management Firmware, hence reverted the patch previously.
Commit ff8356060e ("Revert "dt-bindings: pinctrl-zynqmp: Add
output-enable configuration"").
Support for configuring these properties added in Xilinx ZynqMP Platform
Management firmware(PMUFW) Configuration Set version 2.0. Linux firmware
driver checks if the configuration is supported by the PMUFW when it gets
request for TRISTATE configuration from pinctrl driver. If it supports,
then calls will be made otherwise it returns error.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230731095026.3766675-4-sai.krishna.potthuri@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_generic_add_function() doesn't check result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230719202253.13469-4-s.shtylyov@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register_one_pin() doesn't check the result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230719202253.13469-3-s.shtylyov@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_generic_add_group() doesn't check the result of radix_tree_insert()
despite they both may return a negative error code. Linus Walleij said he
has copied the radix tree code from kernel/irq/ where the functions calling
radix_tree_insert() are *void* themselves; I think it makes more sense to
propagate the errors from radix_tree_insert() upstream if we can do that...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20230719202253.13469-2-s.shtylyov@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230714174901.4062397-1-robh@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
