[ Upstream commit 914a7b3563 ]
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f228af11df ]
We need to set it to the most recent completed fence, not the most
recent submitted. Otherwise we have races where we think we can retire
submits that the GPU is not finished with, if the GPU doesn't manage to
overwrite the seqno before we look at it.
This can show up with hang recovery if one of the submits after the
crashing submit also hangs after it is replayed.
Fixes: f97decac5f ("drm/msm: Support multiple ringbuffers")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea8912b788 ]
usleep_range() may take longer than the max argument due to scheduling,
especially under load. This is causing random errors in the transmitted
IR. Remove the usleep_range() in favour of busy-looping with udelay().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1769bb68a ]
This reverts commit 76d164f582.
PCIe hung issue was observed on multiple platforms. The issue was reproduced
when DUT was configured as AP and associated with 50+ STAs.
For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size
of the RD/WR access to the HOST MEM.
0 - No split , RAW read/write transfer size from MAC is put out on bus
as burst length
1 - Split at 256 byte boundary
2,3 - Reserved
With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when
issue happened. It broke PCIe spec and caused PCIe stuck. So revert
the default value from 0 to 1.
Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047
QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044
Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b648a5132c ]
The kernel test robot pointed out a slightly different error message
after recent commit 5456ffdee6 ("powerpc/spufs: simplify spufs core
dumping") to spufs for a configuration that never worked:
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_proxydma_info_dump':
>> file.c:(.text+0x4c68): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_dma_info_dump':
file.c:(.text+0x4d70): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_wbox_info_dump':
file.c:(.text+0x4df4): undefined reference to `.dump_emit'
Add a Kconfig dependency to prevent this from happening again.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200706132302.3885935-1-arnd@arndb.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b38b298aa4 ]
__hyp_call_panic_nvhe contains inline assembly which did not declare
its dependency on the __hyp_panic_string symbol.
The static-declared string has previously been kept alive because of a use in
__hyp_call_panic_vhe. Fix this in preparation for separating the source files
between VHE and nVHE when the two users land in two different compilation
units. The static variable otherwise gets dropped when compiling the nVHE
source file, causing an undefined symbol linker error later.
Signed-off-by: David Brazdil <dbrazdil@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200625131420.71444-2-dbrazdil@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa99677342 ]
Make sure the delayed work stopped before releasing the resources.
cancel_delayed_work_sync() will only guarantee that the work finishes
executing if the work is already in the ->worklist. That means after
the cancel_delayed_work_sync() returns, it will leave the work requeued
if it was rearmed at the end. That can lead to a use after free once the
work struct is freed.
Fix it by flushing the delayed work instead of trying to cancel it, and
ensure that the work doesn't rearm if the mdsc is stopping.
URL: https://tracker.ceph.com/issues/46293
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7f8b1c2ac ]
The incoming qgroup reserved space timing will move the data reservation
to ordered extent completely.
However in btrfs_punch_hole_lock_range() will call
btrfs_invalidate_page(), which will clear QGROUP_RESERVED bit for the
range.
In current stage it's OK, but if we're making ordered extents handle the
reserved space, then btrfs_punch_hole_lock_range() can clear the
QGROUP_RESERVED bit before we submit ordered extent, leading to qgroup
reserved space leakage.
So here change the timing to make reserve data space after
btrfs_punch_hole_lock_range().
The new timing is fine for either current code or the new code.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ef9b28aa ]
Though the number of lock-acquisitions is tracked as unsigned long, this
is passed as the divisor to div_s64() which interprets it as a s32,
giving nonsense values with more than 2 billion acquisitons. E.g.
acquisitions holdtime-min holdtime-max holdtime-total holdtime-avg
-------------------------------------------------------------------------
2350439395 0.07 353.38 649647067.36 0.-32
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20200725185110.11588-1-chris@chris-wilson.co.uk
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 990a116298 ]
nouveau_connector_detect() calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2cdf39536 ]
nv50_disp_atomic_commit() calls calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfad51c763 ]
nouveau_fbcon_open() calls calls pm_runtime_get_sync() that
increments the reference count. In case of failure, decrement the
ref count before returning the error.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99c787cfd2 ]
During umount, f2fs_put_super() unregisters procfs entries after
f2fs_destroy_segment_manager(), it may cause use-after-free
issue when umount races with procfs accessing, fix it by relocating
f2fs_unregister_sysfs().
[Chao Yu: change commit title/message a bit]
Signed-off-by: Li Guifu <bluce.liguifu@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68f775ddd2 ]
Add HID_QUIRK_NOGET for Logitech GROUP device.
Logitech GROUP is a compound with camera and audio.
When the HID interface in an audio device is requested to get
specific report id, all following control transfers are stalled
and never be restored back.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203419
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5656bb3857 ]
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse.
To use the TMR_FIPER register to generate desired periodic
pulses. The value should programmed is,
desired_period - tclk_period
Current tmr-fiper2 value is to generate 100us periodic pulses.
(But the value should have been 99995, not 99990. The tclk_period is 5.)
This patch is to generate 1 second periodic pulses with value
999999995 programmed which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a94644b44 ]
kobject_init_and_add() takes a reference even when it fails. If it returns
an error, kobject_put() must be called to clean up the memory associated
with the object.
When kobject_init_and_add() fails, call kobject_put() instead of kfree().
b8eb718348 ("net-sysfs: Fix reference count leak in
rx|netdev_queue_add_kobject") fixed a similar problem.
Link: https://lore.kernel.org/r/20200528021322.1984-1-wu000273@umn.edu
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3337bf41e0 ]
An extra count on ebb_state.stats.pmc_count[PMC_INDEX(pmc)] is being per-
formed when count_pmc() is used to reset PMCs on a few selftests. This
extra pmc_count can occasionally invalidate results, such as the ones from
cycles_test shown hereafter. The ebb_check_count() failed with an above
the upper limit error due to the extra value on ebb_state.stats.pmc_count.
Furthermore, this extra count is also indicated by extra PMC1 trace_log on
the output of the cycle test (as well as on pmc56_overflow_test):
==========
...
[21]: counter = 8
[22]: register SPRN_MMCR0 = 0x0000000080000080
[23]: register SPRN_PMC1 = 0x0000000080000004
[24]: counter = 9
[25]: register SPRN_MMCR0 = 0x0000000080000080
[26]: register SPRN_PMC1 = 0x0000000080000004
[27]: counter = 10
[28]: register SPRN_MMCR0 = 0x0000000080000080
[29]: register SPRN_PMC1 = 0x0000000080000004
>> [30]: register SPRN_PMC1 = 0x000000004000051e
PMC1 count (0x280000546) above upper limit 0x2800003e8 (+0x15e)
[FAIL] Test FAILED on line 52
failure: cycles
==========
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200626164737.21943-1-desnesn@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96355d5a1f ]
In tracking down a problem in this patchset, I discovered we are
reclaiming dirty stale inodes. This wasn't discovered until inodes
were always attached to the cluster buffer and then the rcu callback
that freed inodes was assert failing because the inode still had an
active pointer to the cluster buffer after it had been reclaimed.
Debugging the issue indicated that this was a pre-existing issue
resulting from the way the inodes are handled in xfs_inactive_ifree.
When we free a cluster buffer from xfs_ifree_cluster, all the inodes
in cache are marked XFS_ISTALE. Those that are clean have nothing
else done to them and so eventually get cleaned up by background
reclaim. i.e. it is assumed we'll never dirty/relog an inode marked
XFS_ISTALE.
On journal commit dirty stale inodes as are handled by both
buffer and inode log items to run though xfs_istale_done() and
removed from the AIL (buffer log item commit) or the log item will
simply unpin it because the buffer log item will clean it. What happens
to any specific inode is entirely dependent on which log item wins
the commit race, but the result is the same - stale inodes are
clean, not attached to the cluster buffer, and not in the AIL. Hence
inode reclaim can just free these inodes without further care.
However, if the stale inode is relogged, it gets dirtied again and
relogged into the CIL. Most of the time this isn't an issue, because
relogging simply changes the inode's location in the current
checkpoint. Problems arise, however, when the CIL checkpoints
between two transactions in the xfs_inactive_ifree() deferops
processing. This results in the XFS_ISTALE inode being redirtied
and inserted into the CIL without any of the other stale cluster
buffer infrastructure being in place.
Hence on journal commit, it simply gets unpinned, so it remains
dirty in memory. Everything in inode writeback avoids XFS_ISTALE
inodes so it can't be written back, and it is not tracked in the AIL
so there's not even a trigger to attempt to clean the inode. Hence
the inode just sits dirty in memory until inode reclaim comes along,
sees that it is XFS_ISTALE, and goes to reclaim it. This reclaiming
of a dirty inode caused use after free, list corruptions and other
nasty issues later in this patchset.
Hence this patch addresses a violation of the "never log XFS_ISTALE
inodes" caused by the deferops processing rolling a transaction
and relogging a stale inode in xfs_inactive_free. It also adds a
bunch of asserts to catch this problem in debug kernels so that
we don't reintroduce this problem in future.
Reproducer for this issue was generic/558 on a v4 filesystem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03dbfe0668 ]
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f79f94765f ]
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e008fa6fb4 ]
in amdgpu_display_crtc_set_config, the call to pm_runtime_get_sync
increments the counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5509ac65f2 ]
in amdgpu_drm_ioctl the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ba8923cbb ]
in amdgpu_driver_open_kms the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f2e8acdb4 ]
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20eca0123a ]
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3e3d2be68 ]
Unlike the other instances which represent a complete loss of
consistency within the rcache mechanism itself, or a fundamental
and obvious misconfiguration by an IOMMU driver, the BUG_ON() in
iova_magazine_free_pfns() can be provoked at more or less any time
in a "spooky action-at-a-distance" manner by any old device driver
passing nonsense to dma_unmap_*() which then propagates through to
queue_iova().
Not only is this well outside the IOVA layer's control, it's also
nowhere near fatal enough to justify panicking anyway - all that
really achieves is to make debugging the offending driver more
difficult. Let's simply WARN and otherwise ignore bogus PFNs.
Reported-by: Prakash Gupta <guptap@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Prakash Gupta <guptap@codeaurora.org>
Link: https://lore.kernel.org/r/acbd2d092b42738a03a21b417ce64e27f8c91c86.1591103298.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b431ef837e ]
We make an assumption that a debugfs directory exists, but since
this can fail ensure it exists before allowing blktrace setup to
complete. Otherwise we end up stuffing blktrace files on the debugfs
root directory. In the worst case scenario this *in theory* can create
an eventual panic *iff* in the future a similarly named file is created
prior on the debugfs root directory. This theoretical crash can happen
due to a recursive removal followed by a specific dentry removal.
This doesn't fix any known crash, however I have seen the files
go into the main debugfs root directory in cases where the debugfs
directory was not created due to other internal bugs with blktrace
now fixed.
blktrace is also completely useless without this directory, so
this ensures to userspace we only setup blktrace if the kernel
can stuff files where they are supposed to go into.
debugfs directory creations typically aren't checked for, and we have
maintainers doing sweep removals of these checks, but since we need this
check to ensure proper userspace blktrace functionality we make sure
to annotate the justification for the check.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6499a0db9b ]
The value av7110->debi_virt is stored in DMA memory, and it is assigned
to data, and thus data[0] can be modified at any time by malicious
hardware. In this case, "if (data[0] < 2)" can be passed, but then
data[0] can be changed into a large number, which may cause buffer
overflow when the code "av7110->ci_slot[data[0]]" is used.
To fix this possible bug, data[0] is assigned to a local variable, which
replaces the use of data[0].
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0f5c7076e ]
Processing NETDEV_FEAT_CHANGE causes IPvlan links to lose
NETIF_F_LLTX feature because of the incorrect handling of
features in ipvlan_fix_features().
--before--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Actual changes:
vlan-challenged: off [fixed]
tx-lockless: off [fixed]
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: off [fixed]
lpaa10:~#
--after--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Could not change any device features
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~#
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ccd143e515 ]
Most statistics in ena driver are incremented, meaning that a stat's
value is a sum of all increases done to it since driver/queue
initialization.
This patch makes all statistics this way, effectively making missed_tx
statistic incremental.
Also added a comment regarding rx_drops and tx_drops to make it
clearer how these counters are calculated.
Fixes: 11095fdb71 ("net: ena: add statistics for missed tx packets")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
