[ Upstream commit 5ffa828534 ]
The intent here was to return negative error codes but it actually
returns positive values. The problem is that type promotion with
ternary operations is quite complicated.
"ret" is an int. "copied" is a u32. And the snoop_file_read() function
returns long. What happens is that "ret" is cast to u32 and becomes
positive then it's cast to long and it's still positive.
Fix this by removing the ternary so that "ret" is type promoted directly
to long.
Fixes: 3772e5da44 ("drivers/misc: Aspeed LPC snoop output using misc chardev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Patrick Venture <venture@google.com>
Link: https://lore.kernel.org/r/YIE90PSXsMTa2Y8n@mwanda
Link: https://lore.kernel.org/r/20210423000919.1249474-1-joel@jms.id.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d75e7f63b7 ]
Prior to commit 4a8c31a1c6 ("xen/blkback: rework connect_ring() to avoid
inconsistent xenstore 'ring-page-order' set by malicious blkfront"), the
behaviour of xen-blkback when connecting to a frontend was:
- read 'ring-page-order'
- if not present then expect a single page ring specified by 'ring-ref'
- else expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
This was correct behaviour, but was broken by the afforementioned commit to
become:
- read 'ring-page-order'
- if not present then expect a single page ring (i.e. ring-page-order = 0)
- expect a ring specified by 'ring-refX' where X is between 0 and
1 << ring-page-order
- if that didn't work then see if there's a single page ring specified by
'ring-ref'
This incorrect behaviour works most of the time but fails when a frontend
that sets 'ring-page-order' is unloaded and replaced by one that does not
because, instead of reading 'ring-ref', xen-blkback will read the stale
'ring-ref0' left around by the previous frontend will try to map the wrong
grant reference.
This patch restores the original behaviour.
Fixes: 4a8c31a1c6 ("xen/blkback: rework connect_ring() to avoid inconsistent xenstore 'ring-page-order' set by malicious blkfront")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: "Roger Pau Monné" <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210202175659.18452-1-paul@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24d209dba5 ]
When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.
- Added dwc_handle_gpwrdn_disc_det() function which handles
gpwrdn disconnect detect flow and exits hibernation
without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
calling dwc_handle_gpwrdn_disc_det() function. Here no register
is restored which is the solution described above.
Fixes: 65c9c4c6b0 ("usb: dwc2: Add dwc2_handle_gpwrdn_intr() handler")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124715.75355A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77db0ec8b7 ]
When running in Azure, disks may be connected to a Linux VM with
read/write caching enabled. If a VM panics and issues a VMbus
UNLOAD request to Hyper-V, the response is delayed until all dirty
data in the disk cache is flushed. In extreme cases, this flushing
can take 10's of seconds, depending on the disk speed and the amount
of dirty data. If kdump is configured for the VM, the current 10 second
timeout in vmbus_wait_for_unload() may be exceeded, and the UNLOAD
complete message may arrive well after the kdump kernel is already
running, causing problems. Note that no problem occurs if kdump is
not enabled because Hyper-V waits for the cache flush before doing
a reboot through the BIOS/UEFI code.
Fix this problem by increasing the timeout in vmbus_wait_for_unload()
to 100 seconds. Also output periodic messages so that if anyone is
watching the serial console, they won't think the VM is completely
hung.
Fixes: 911e1987ef ("Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/1618894089-126662-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2209ea556 ]
When KEXEC is disabled, the UV build fails:
arch/x86/platform/uv/uv_nmi.c:875:14: error: ‘uv_nmi_kexec_failed’ undeclared (first use in this function)
Since uv_nmi_kexec_failed is only defined in the KEXEC_CORE #ifdef branch,
this code cannot ever have been build tested:
if (main)
pr_err("UV: NMI kdump: KEXEC not supported in this kernel\n");
atomic_set(&uv_nmi_kexec_failed, 1);
Nor is this use possible in uv_handle_nmi():
atomic_set(&uv_nmi_kexec_failed, 0);
These bugs were introduced in this commit:
d0a9964e98: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Which added the uv_nmi_kexec_failed assignments to !KEXEC code, while making the
definition KEXEC-only - apparently without testing the !KEXEC case.
Instead of complicating the #ifdef maze, simplify the code by requiring X86_UV
to depend on KEXEC_CORE. This pattern is present in other architectures as well.
( We'll remove the untested, 7 years old !KEXEC complications from the file in a
separate commit. )
Fixes: d0a9964e98: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d21e5abd3a ]
pmc_plt_clk* clocks are used for ethernet controllers, so need to stay
turned on. This adds the affected board family to critclk_systems DMI
table, so the clocks are marked as CLK_CRITICAL and not turned off.
This replaces the previously listed boards with a match for the whole
device family CBxx63. CBxx63 matches only baytrail devices.
There are new affected boards that would otherwise need to be listed.
There are unaffected boards in the family, but having the clocks
turned on is not an issue.
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Link: https://lore.kernel.org/r/20210412133006.397679-1-linux-kernel-dev@beckhoff.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ce535ec00 ]
We can't use kfree() to free device managed resources so the kfree(dev)
is against the rules.
It's easier to write this code if we open code the device_register() as
a device_initialize() and device_add(). That way if dev_set_name() set
name fails we can call put_device() and it will clean up correctly.
Fixes: acc02a109b ("node: Add memory-side caching attributes")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YHA0JUra+F64+NpB@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2954a6f12f ]
When CONFIG_QCOM_SCM is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:
drivers/firmware/qcom_scm-smc.o: In function `__scm_smc_do_quirk':
qcom_scm-smc.c:(.text+0x36): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call':
qcom_scm-legacy.c:(.text+0xe2): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call_atomic':
qcom_scm-legacy.c:(.text+0x1f0): undefined reference to `__arm_smccc_smc'
Note that __arm_smccc_smc is defined when HAVE_ARM_SMCCC is y.
So add dependency on HAVE_ARM_SMCCC in QCOM_SCM configuration.
Fixes: 916f743da3 ("firmware: qcom: scm: Move the scm driver to drivers/firmware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210406094200.60952-1-heying24@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79c5966cec ]
Drivers can return -ENOIOCTLCMD when an ioctl is not recognised to tell
the upper layers to continue looking for a handler.
This is not the case for the RS485 and ISO7816 ioctls whose handlers
should return -ENOTTY directly in case a serial driver does not
implement the corresponding methods.
Fixes: a5f276f10f ("serial_core: Handle TIOC[GS]RS485 ioctls.")
Fixes: ad8c0eaa0a ("tty/serial_core: add ISO7816 infrastructure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b8b20868a ]
Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Fix up the TIOCMGET, TIOCMSET and TIOCGICOUNT helpers which returned
-EINVAL when a tty driver did not implement the corresponding
operations.
Note that the TIOCMGET and TIOCMSET helpers predate git and do not get a
corresponding Fixes tag below.
Fixes: d281da7ff6 ("tty: Make tiocgicount a handler")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d09845e98a ]
Some kernel-internal ASYNC flags have been superseded by tty-port flags
and should no longer be used by kernel drivers.
Fix the misspelled "__KERNEL__" compile guards which failed their sole
purpose to break out-of-tree drivers that have not yet been updated.
Fixes: 5c0517fefc ("tty: core: Undefine ASYNC_* flags superceded by TTY_PORT* flags")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4969602741 ]
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e6 ("USB: allow users to run setserial with cdc-acm")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd5619582d ]
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bad3bf23c ]
When current CPU load is not L0 then loading armada-37xx-cpufreq.ko driver
fails with following error:
# modprobe armada-37xx-cpufreq
[ 502.702097] Unsupported CPU frequency 250 MHz
This issue was partially fixed by commit 8db8256345 ("cpufreq:
armada-37xx: fix frequency calculation for opp"), but only for calculating
CPU frequency for opp.
Fix this also for determination of base CPU frequency.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com>
Tested-by: Philip Soares <philips@netisense.com>
Fixes: 92ce45fb87 ("cpufreq: Add DVFS support for Armada 37xx")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92963903a8 ]
Commit 8db8256345 ("cpufreq: armada-37xx: fix frequency calculation for
opp") changed calculation of frequency passed to the dev_pm_opp_add()
function call. But the code for dev_pm_opp_remove() function call was not
updated, so the driver cleanup phase does not work when registration fails.
This fixes the issue by using the same frequency in both calls.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com>
Tested-by: Philip Soares <philips@netisense.com>
Fixes: 8db8256345 ("cpufreq: armada-37xx: fix frequency calculation for opp")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e93033aff6 ]
When CPU frequency is at 250 MHz and set_rate() is called with 500 MHz (L1)
quickly followed by a call with 1 GHz (L0), the CPU does not necessarily
stay in L1 for at least 20ms as is required by Marvell errata.
This situation happens frequently with the ondemand cpufreq governor and
can be also reproduced with userspace governor. In most cases it causes CPU
to crash.
This change fixes the above issue and ensures that the CPU always stays in
L1 for at least 20ms when switching from any state to L0.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com>
Tested-by: Philip Soares <philips@netisense.com>
Fixes: 61c40f35f5 ("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to 1.2GHz")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4decb91875 ]
It was observed that the workaround introduced by commit 61c40f35f5
("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to
1.2GHz") when base CPU frequency is 1.2 GHz is also required when base
CPU frequency is 1 GHz. Otherwise switching CPU frequency directly from
L2 (250 MHz) to L0 (1 GHz) causes a crash.
When base CPU frequency is just 800 MHz no crashed were observed during
switch from L2 to L0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com>
Tested-by: Philip Soares <philips@netisense.com>
Fixes: 2089dc33ea ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d118ac2062 ]
The original CPU voltage value for load L1 is too low for Armada 37xx SoC
when base CPU frequency is 1000 or 1200 MHz. It leads to instabilities
where CPU gets stuck soon after dynamic voltage scaling from load L1 to L0.
Update the CPU voltage value for load L1 accordingly when base frequency is
1000 or 1200 MHz. The minimal L1 value for base CPU frequency 1000 MHz is
updated from the original 1.05V to 1.108V and for 1200 MHz is updated to
1.155V. This minimal L1 value is used only in the case when it is lower
than value for L0.
This change fixes CPU instability issues on 1 GHz and 1.2 GHz variants of
Espressobin and 1 GHz Turris Mox.
Marvell previously for 1 GHz variant of Espressobin provided a patch [1]
suitable only for their Marvell Linux kernel 4.4 fork which workarounded
this issue. Patch forced CPU voltage value to 1.108V in all loads. But
such change does not fix CPU instability issues on 1.2 GHz variants of
Armada 3720 SoC.
During testing we come to the conclusion that using 1.108V as minimal
value for L1 load makes 1 GHz variants of Espressobin and Turris Mox boards
stable. And similarly 1.155V for 1.2 GHz variant of Espressobin.
These two values 1.108V and 1.155V are documented in Armada 3700 Hardware
Specifications as typical initial CPU voltage values.
Discussion about this issue is also at the Armbian forum [2].
[1] - dc33b62c90
[2] - https://forum.armbian.com/topic/10429-how-to-make-espressobin-v7-stable/
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com>
Tested-by: Philip Soares <philips@netisense.com>
Fixes: 1c3528232f ("cpufreq: armada-37xx: Add AVS support")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e435a9dd2 ]
Remove the .set_parent method in clk_pm_cpu_ops.
This method was supposed to be needed by the armada-37xx-cpufreq driver,
but was never actually called due to wrong assumptions in the cpufreq
driver. After this was fixed in the cpufreq driver, this method is not
needed anymore.
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com>
Tested-by: Philip Soares <philips@netisense.com>
Fixes: 2089dc33ea ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22592df194 ]
With CPU frequency determining software [1] we have discovered that
after this driver does one CPU frequency change, the base frequency of
the CPU is set to the frequency of TBG-A-P clock, instead of the TBG
that is parent to the CPU.
This can be reproduced on EspressoBIN and Turris MOX:
cd /sys/devices/system/cpu/cpufreq/policy0
echo powersave >scaling_governor
echo performance >scaling_governor
Running the mhz tool before this driver is loaded reports 1000 MHz, and
after loading the driver and executing commands above the tool reports
800 MHz.
The change of TBG clock selector is supposed to happen in function
armada37xx_cpufreq_dvfs_setup. Before the function returns, it does
this:
parent = clk_get_parent(clk);
clk_set_parent(clk, parent);
The armada-37xx-periph clock driver has the .set_parent method
implemented correctly for this, so if the method was actually called,
this would work. But since the introduction of the common clock
framework in commit b2476490ef ("clk: introduce the common clock..."),
the clk_set_parent function checks whether the parent is actually
changing, and if the requested new parent is same as the old parent
(which is obviously the case for the code above), the .set_parent method
is not called at all.
This patch fixes this issue by filling the correct TBG clock selector
directly in the armada37xx_cpufreq_dvfs_setup during the filling of
other registers at the same address. But the determination of CPU TBG
index cannot be done via the common clock framework, therefore we need
to access the North Bridge Peripheral Clock registers directly in this
driver.
[1] https://github.com/wtarreau/mhz
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com>
Tested-by: Philip Soares <philips@netisense.com>
Fixes: 92ce45fb87 ("cpufreq: Add DVFS support for Armada 37xx")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7cae626ca ]
In adf_create_ring, if the callee adf_init_ring() failed, the callee will
free the ring->base_addr by dma_free_coherent() and return -EFAULT. Then
adf_create_ring will goto err and the ring->base_addr will be freed again
in adf_cleanup_ring().
My patch sets ring->base_addr to NULL after the first freed to avoid the
double free.
Fixes: a672a9dc87 ("crypto: qat - Intel(R) QAT transport code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bc6262c61 ]
All of the CPPC sysfs show functions are called via indirect call in
kobj_attr_show(), where they should be of type
ssize_t (*show)(struct kobject *kobj, struct kobj_attribute *attr, char *buf);
because that is the type of the ->show() member in
'struct kobj_attribute' but they are actually of type
ssize_t (*show)(struct kobject *kobj, struct attribute *attr, char *buf);
because of the ->show() member in 'struct cppc_attr', resulting in a
Control Flow Integrity violation [1].
$ cat /sys/devices/system/cpu/cpu0/acpi_cppc/highest_perf
3400
$ dmesg | grep "CFI failure"
[ 175.970559] CFI failure (target: show_highest_perf+0x0/0x8):
As far as I can tell, the only difference between 'struct cppc_attr'
and 'struct kobj_attribute' aside from the type of the attr parameter
is the type of the count parameter in the ->store() member (ssize_t vs.
size_t), which does not actually matter because all of these nodes are
read-only.
Eliminate 'struct cppc_attr' in favor of 'struct kobj_attribute' to fix
the violation.
[1]: https://lore.kernel.org/r/20210401233216.2540591-1-samitolvanen@google.com/
Fixes: 158c998ea4 ("ACPI / CPPC: add sysfs support to compute delivered performance")
Link: https://github.com/ClangBuiltLinux/linux/issues/1343
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0648c55e3a ]
Given that no validation of how much data the firmware loader read in
for a given segment truncated segment files would best case result in a
hash verification failure, without any indication of what went wrong.
Improve this by validating that the firmware loader did return the
amount of data requested.
Fixes: 445c2410a4 ("soc: qcom: mdt_loader: Use request_firmware_into_buf()")
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210107232526.716989-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 794aaf0144 ]
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62453f1ba5 ]
Use the more accurate returned new_freq as resume_freq.
It's the same as how devfreq->previous_freq was updated.
Fixes: 83f8ca45af ("PM / devfreq: add support for suspend/resume of a devfreq device")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60c6b305c1 ]
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the greybus implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: e68453ed28 ("greybus: uart-gb: now builds, more framework added")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407102334.32361-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9b9263a25 ]
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of riv->ieee80211->LinkDetectInfo.SlotNum
that is a u16 type. There is a potential infinite loop if SlotNum
is larger than the u8 loop counter. Fix this by making the loop
counter the same type as SlotNum.
Addresses-Coverity: ("Infinite loop")
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210407150308.496623-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e13d96670 ]
When building with extra warnings enabled, clang points out a
mistake in the error handling:
drivers/irqchip/irq-gic-v3-mbi.c:306:21: error: result of comparison of constant 18446744073709551615 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (mbi_phys_base == OF_BAD_ADDR) {
Truncate the constant to the same type as the variable it gets compared
to, to shut make the check work and void the warning.
Fixes: 505287525c ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323131842.2773094-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 076de75de1 ]
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9a ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd4d607044 ]
Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.
The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.
The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:
[<80106550>] show_stack+0x20/0x24
[<80106868>] dump_stack+0x28/0x30
[<80823540>] __warn+0xfc/0x110
[<8011ac30>] warn_slowpath_fmt+0xb0/0xc0
[<8011ad44>] dma_map_page_attrs+0x24c/0x314
[<8016a27c>] usb_gadget_map_request_by_dev+0x100/0x1e4
[<805cedd8>] usb_gadget_map_request+0x1c/0x20
[<805cefbc>] ast_vhub_epn_queue+0xa0/0x1d8
[<7f02f710>] usb_ep_queue+0x48/0xc4
[<805cd3e8>] ecm_do_notify+0xf8/0x248
[<7f145920>] ecm_set_alt+0xc8/0x1d0
[<7f145c34>] composite_setup+0x680/0x1d30
[<7f00deb8>] ast_vhub_ep0_handle_setup+0xa4/0x1bc
[<7f02ee94>] ast_vhub_dev_irq+0x58/0x84
[<7f0309e0>] ast_vhub_irq+0xb0/0x1c8
[<7f02e118>] __handle_irq_event_percpu+0x50/0x19c
[<8015e5bc>] handle_irq_event_percpu+0x38/0x8c
[<8015e758>] handle_irq_event+0x38/0x4c
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20210331045831.28700-1-rentao.bupt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83dc1173d7 ]
The function adf_isr_resource_alloc() is not unwinding correctly in case
of error.
This patch fixes the error paths and propagate the errors to the caller.
Fixes: 7afa232e76 ("crypto: qat - Intel(R) QAT DH895xcc accelerator")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
