[ Upstream commit 143c2a89e0 ]
When running kprobe on -rt kernel, the below bug is caught:
|BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:931
|in_atomic(): 1, irqs_disabled(): 128, pid: 14, name: migration/0
|Preemption disabled at:[<802f2b98>] cpu_stopper_thread+0xc0/0x140
|CPU: 0 PID: 14 Comm: migration/0 Tainted: G O 4.8.3-rt2 #1
|Hardware name: Freescale LS1021A
|[<8025a43c>] (___might_sleep)
|[<80b5b324>] (rt_spin_lock)
|[<80b5c31c>] (__patch_text_real)
|[<80b5c3ac>] (patch_text_stop_machine)
|[<802f2920>] (multi_cpu_stop)
Since patch_text_stop_machine() is called in stop_machine() which
disables IRQ, sleepable lock should be not used in this atomic context,
so replace patch_lock to raw lock.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85b0cae89d ]
Gigabyte X299 DESIGNARE EX motherboard has one PCIe root port that is
connected to an Alpine Ridge Thunderbolt controller. This port has slot
implemented bit set in the config space but other than that it is not
hotplug capable in the sense we are expecting in Linux (it has
dev->is_hotplug_bridge set to 0):
00:1c.4 PCI bridge: Intel Corporation 200 Series PCH PCI Express Root Port #5
Bus: primary=00, secondary=05, subordinate=46, sec-latency=0
Memory behind bridge: 78000000-8fffffff [size=384M]
Prefetchable memory behind bridge: 00003800f8000000-00003800ffffffff [size=128M]
...
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
...
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #8, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState+
This system is using ACPI based hotplug to notify the OS that it needs to
rescan the PCI bus (ACPI hotplug).
If there is nothing connected in any of the Thunderbolt ports the root port
will not have any runtime PM active children and is thus automatically
runtime suspended pretty soon after boot by PCI PM core. Now, when a
device is connected the BIOS SMI handler responsible for enumerating newly
added devices is not able to find anything because the port is in D3.
Prevent this from happening by blacklisting PCI power management of this
particular Gigabyte system.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202031
Reported-by: Kedar A Dongre <kedar.a.dongre@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0f890aba2 ]
This patch is to add the AMBA device ID for CA73 CPU, so that CPU debug
module can be initialized successfully when a SoC contain CA73 CPUs.
This patch has been verified on 96boards Hikey960.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6a3e1475b ]
On some Samsung hardware, it is necessary to clear events accumulated by
the EC during sleep. These ECs stop reporting GPEs until they are manually
polled, if too many events are accumulated.
Thus the CLEAR_ON_RESUME quirk is introduced to send EC query commands
unconditionally after resume to clear all the EC query events on those
platforms.
Later, commit 4c237371f2 ("ACPI / EC: Remove old CLEAR_ON_RESUME quirk")
removes the CLEAR_ON_RESUME quirk because we thought the new EC IRQ
polling logic should handle this case.
Now it has been proved that the EC IRQ Polling logic does not fix the
issue actually because we got regression report on these Samsung
platforms after removing the quirk.
Thus revert commit 4c237371f2 ("ACPI / EC: Remove old CLEAR_ON_RESUME
quirk") to introduce back the Samsung quirk in this patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=44161
Tested-by: Ortwin Glück <odi@odi.ch>
Tested-by: Francisco Cribari <cribari@gmail.com>
Tested-by: Balazs Varga <balazs4web@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c34a83820f ]
Clients may submit a new requests from the completion callback
context. The driver was not prepared to receive a request in this
state because it already held the request queue lock and a recursive
lock error is triggered.
Now all completions are queued up until we are ready to drop the queue
lock and then delivered.
The fault was triggered by TCP over an IPsec connection in the LTP
test suite:
LTP: starting tcp4_ipsec02 (tcp_ipsec.sh -p ah -m transport -s "100 1000 65535")
BUG: spinlock recursion on CPU#1, genload/943
lock: 0xbf3c3094, .magic: dead4ead, .owner: genload/943, .owner_cpu: 1
CPU: 1 PID: 943 Comm: genload Tainted: G O 4.9.62-axis5-devel #6
Hardware name: Axis ARTPEC-6 Platform
(unwind_backtrace) from [<8010d134>] (show_stack+0x18/0x1c)
(show_stack) from [<803a289c>] (dump_stack+0x84/0x98)
(dump_stack) from [<8016e164>] (do_raw_spin_lock+0x124/0x128)
(do_raw_spin_lock) from [<804de1a4>] (artpec6_crypto_submit+0x2c/0xa0)
(artpec6_crypto_submit) from [<804def38>] (artpec6_crypto_prepare_submit_hash+0xd0/0x54c)
(artpec6_crypto_prepare_submit_hash) from [<7f3165f0>] (ah_output+0x2a4/0x3dc [ah4])
(ah_output [ah4]) from [<805df9bc>] (xfrm_output_resume+0x178/0x4a4)
(xfrm_output_resume) from [<805d283c>] (xfrm4_output+0xac/0xbc)
(xfrm4_output) from [<80587928>] (ip_queue_xmit+0x140/0x3b4)
(ip_queue_xmit) from [<805a13b4>] (tcp_transmit_skb+0x4c4/0x95c)
(tcp_transmit_skb) from [<8059f218>] (tcp_rcv_state_process+0xdf4/0xdfc)
(tcp_rcv_state_process) from [<805a7530>] (tcp_v4_do_rcv+0x64/0x1ac)
(tcp_v4_do_rcv) from [<805a9724>] (tcp_v4_rcv+0xa34/0xb74)
(tcp_v4_rcv) from [<80581d34>] (ip_local_deliver_finish+0x78/0x2b0)
(ip_local_deliver_finish) from [<8058259c>] (ip_local_deliver+0xe4/0x104)
(ip_local_deliver) from [<805d23ec>] (xfrm4_transport_finish+0xf4/0x144)
(xfrm4_transport_finish) from [<805df564>] (xfrm_input+0x4f4/0x74c)
(xfrm_input) from [<804de420>] (artpec6_crypto_task+0x208/0x38c)
(artpec6_crypto_task) from [<801271b0>] (tasklet_action+0x60/0xec)
(tasklet_action) from [<801266d4>] (__do_softirq+0xcc/0x3a4)
(__do_softirq) from [<80126d20>] (irq_exit+0xf4/0x15c)
(irq_exit) from [<801741e8>] (__handle_domain_irq+0x68/0xbc)
(__handle_domain_irq) from [<801014f0>] (gic_handle_irq+0x50/0x94)
(gic_handle_irq) from [<80657370>] (__irq_usr+0x50/0x80)
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46f3ceaffa ]
Move mipi_dsi_dcs_set_display_off() from innolux_panel_disable()
to innolux_panel_unprepare(), so they are consistent with
innolux_panel_enable() and innolux_panel_prepare().
This also fixes some mode check and irq timeout issue in MTK dsi code.
Since some dsi code (e.g. mtk_dsi) have following call trace:
1. drm_panel_disable(), which calls innolux_panel_disable()
2. switch to cmd mode
3. drm_panel_unprepare(), which calls innolux_panel_unprepare()
However, mtk_dsi needs to be in cmd mode to be able to send commands
(e.g. mipi_dsi_dcs_set_display_off() and mipi_dsi_dcs_enter_sleep_mode()),
so we need these functions to be called after the switch to cmd mode happens,
i.e. in innolux_panel_unprepare.
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190109065922.231753-1-hsinyi@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59a12205d3 ]
Introduce lkdtm tests for NULL pointer dereference: check access or exec
at NULL address, since these errors tend to be reported differently from
the general fault error text. For example from x86:
pr_alert("BUG: unable to handle kernel %s at %px\n",
address < PAGE_SIZE ? "NULL pointer dereference" : "paging request",
(void *)address);
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c411157a4 ]
Today, when doing a lkdtm test before the readiness of the
random generator, (ptrval) is printed instead of the address
at which it perform the fault:
[ 1597.337030] lkdtm: Performing direct entry EXEC_USERSPACE
[ 1597.337142] lkdtm: attempting ok execution at (ptrval)
[ 1597.337398] lkdtm: attempting bad execution at (ptrval)
[ 1597.337460] kernel tried to execute user page (77858000) -exploit attempt? (uid: 0)
[ 1597.344769] Unable to handle kernel paging request for instruction fetch
[ 1597.351392] Faulting instruction address: 0x77858000
[ 1597.356312] Oops: Kernel access of bad area, sig: 11 [#1]
If the lkdtm test is done later on, it prints an hashed address.
In both cases this is pointless. The purpose of the test is to
ensure the kernel generates an Oops at the expected address,
so real addresses needs to be printed. This patch fixes that.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6e1fd17a3 ]
This fixes splats like the one below if CONFIG_DEBUG_ATOMIC_SLEEP=y
and machine (Tegra30) booted with SMP=n or all secondary CPU's are put
offline. Locking isn't needed because it protects atomic operation.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G C 4.18.0-next-20180821-00180-gc3ebb6544e44-dirty #823
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[<c01134f4>] (unwind_backtrace) from [<c010db2c>] (show_stack+0x20/0x24)
[<c010db2c>] (show_stack) from [<c0bd0f3c>] (dump_stack+0x94/0xa8)
[<c0bd0f3c>] (dump_stack) from [<c0151df8>] (___might_sleep+0x13c/0x174)
[<c0151df8>] (___might_sleep) from [<c0151ea0>] (__might_sleep+0x70/0xa8)
[<c0151ea0>] (__might_sleep) from [<c0bec2b8>] (mutex_lock+0x2c/0x70)
[<c0bec2b8>] (mutex_lock) from [<c0589844>] (tegra_powergate_is_powered+0x44/0xa8)
[<c0589844>] (tegra_powergate_is_powered) from [<c0581a60>] (tegra30_cpu_rail_off_ready+0x30/0x74)
[<c0581a60>] (tegra30_cpu_rail_off_ready) from [<c0122244>] (tegra30_idle_lp2+0xa0/0x108)
[<c0122244>] (tegra30_idle_lp2) from [<c0853438>] (cpuidle_enter_state+0x140/0x540)
[<c0853438>] (cpuidle_enter_state) from [<c08538a4>] (cpuidle_enter+0x40/0x4c)
[<c08538a4>] (cpuidle_enter) from [<c01595e0>] (call_cpuidle+0x30/0x48)
[<c01595e0>] (call_cpuidle) from [<c01599f8>] (do_idle+0x238/0x28c)
[<c01599f8>] (do_idle) from [<c0159d28>] (cpu_startup_entry+0x28/0x2c)
[<c0159d28>] (cpu_startup_entry) from [<c0be76c8>] (rest_init+0xd8/0xdc)
[<c0be76c8>] (rest_init) from [<c1200f50>] (start_kernel+0x41c/0x430)
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 388b4e6a00 ]
scsi_device_quiesce() and scsi_device_resume() are called during
system-wide suspend and resume. scsi_device_quiesce() only succeeds for
SCSI devices that are in one of the RUNNING, OFFLINE or TRANSPORT_OFFLINE
states (see also scsi_set_device_state()). This patch avoids that the
following warning is triggered when resuming a system for which quiescing a
SCSI device failed:
WARNING: CPU: 2 PID: 11303 at drivers/scsi/scsi_lib.c:2600 scsi_device_resume+0x4f/0x58
CPU: 2 PID: 11303 Comm: kworker/u8:70 Not tainted 5.0.0-rc1+ #50
Hardware name: LENOVO 80E3/Lancer 5B2, BIOS A2CN45WW(V2.13) 08/04/2016
Workqueue: events_unbound async_run_entry_fn
Call Trace:
scsi_dev_type_resume+0x2e/0x60
async_run_entry_fn+0x32/0xd8
process_one_work+0x1f4/0x420
worker_thread+0x28/0x3c0
kthread+0x118/0x130
ret_from_fork+0x22/0x40
Cc: Przemek Socha <soprwa@gmail.com>
Reported-by: Przemek Socha <soprwa@gmail.com>
Fixes: 3a0a529971 ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cffaaf0c81 ]
Commit 57384592c4 ("iommu/vt-d: Store bus information in RMRR PCI
device path") changed the type of the path data, however, the change in
path type was not reflected in size calculations. Update to use the
correct type and prevent a buffer overflow.
This bug manifests in systems with deep PCI hierarchies, and can lead to
an overflow of the static allocated buffer (dmar_pci_notify_info_buf),
or can lead to overflow of slab-allocated data.
BUG: KASAN: global-out-of-bounds in dmar_alloc_pci_notify_info+0x1d5/0x2e0
Write of size 1 at addr ffffffff90445d80 by task swapper/0/1
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.14.87-rt49-02406-gd0a0e96 #1
Call Trace:
? dump_stack+0x46/0x59
? print_address_description+0x1df/0x290
? dmar_alloc_pci_notify_info+0x1d5/0x2e0
? kasan_report+0x256/0x340
? dmar_alloc_pci_notify_info+0x1d5/0x2e0
? e820__memblock_setup+0xb0/0xb0
? dmar_dev_scope_init+0x424/0x48f
? __down_write_common+0x1ec/0x230
? dmar_dev_scope_init+0x48f/0x48f
? dmar_free_unused_resources+0x109/0x109
? cpumask_next+0x16/0x20
? __kmem_cache_create+0x392/0x430
? kmem_cache_create+0x135/0x2f0
? e820__memblock_setup+0xb0/0xb0
? intel_iommu_init+0x170/0x1848
? _raw_spin_unlock_irqrestore+0x32/0x60
? migrate_enable+0x27a/0x5b0
? sched_setattr+0x20/0x20
? migrate_disable+0x1fc/0x380
? task_rq_lock+0x170/0x170
? try_to_run_init_process+0x40/0x40
? locks_remove_file+0x85/0x2f0
? dev_prepare_static_identity_mapping+0x78/0x78
? rt_spin_unlock+0x39/0x50
? lockref_put_or_lock+0x2a/0x40
? dput+0x128/0x2f0
? __rcu_read_unlock+0x66/0x80
? __fput+0x250/0x300
? __rcu_read_lock+0x1b/0x30
? mntput_no_expire+0x38/0x290
? e820__memblock_setup+0xb0/0xb0
? pci_iommu_init+0x25/0x63
? pci_iommu_init+0x25/0x63
? do_one_initcall+0x7e/0x1c0
? initcall_blacklisted+0x120/0x120
? kernel_init_freeable+0x27b/0x307
? rest_init+0xd0/0xd0
? kernel_init+0xf/0x120
? rest_init+0xd0/0xd0
? ret_from_fork+0x1f/0x40
The buggy address belongs to the variable:
dmar_pci_notify_info_buf+0x40/0x60
Fixes: 57384592c4 ("iommu/vt-d: Store bus information in RMRR PCI device path")
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c643165020 ]
The SHA512 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69216a545c ]
The SHA256 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f75a2804da ]
xfrm_state_put() moves struct xfrm_state to the GC list
and schedules the GC work to clean it up. On net exit call
path, xfrm_state_flush() is called to clean up and
xfrm_flush_gc() is called to wait for the GC work to complete
before exit.
However, this doesn't work because one of the ->destructor(),
ipcomp_destroy(), schedules the same GC work again inside
the GC work. It is hard to wait for such a nested async
callback. This is also why syzbot still reports the following
warning:
WARNING: CPU: 1 PID: 33 at net/ipv6/xfrm6_tunnel.c:351 xfrm6_tunnel_net_exit+0x2cb/0x500 net/ipv6/xfrm6_tunnel.c:351
...
ops_exit_list.isra.0+0xb0/0x160 net/core/net_namespace.c:153
cleanup_net+0x51d/0xb10 net/core/net_namespace.c:551
process_one_work+0xd0c/0x1ce0 kernel/workqueue.c:2153
worker_thread+0x143/0x14a0 kernel/workqueue.c:2296
kthread+0x357/0x430 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
In fact, it is perfectly fine to bypass GC and destroy xfrm_state
synchronously on net exit call path, because it is in process context
and doesn't need a work struct to do any blocking work.
This patch introduces xfrm_state_put_sync() which simply bypasses
GC, and lets its callers to decide whether to use this synchronous
version. On net exit path, xfrm_state_fini() and
xfrm6_tunnel_net_exit() use it. And, as ipcomp_destroy() itself is
blocking, it can use xfrm_state_put_sync() directly too.
Also rename xfrm_state_gc_destroy() to ___xfrm_state_destroy() to
reflect this change.
Fixes: b48c05ab5d ("xfrm: Fix warning in xfrm6_tunnel_net_exit.")
Reported-and-tested-by: syzbot+e9aebef558e3ed673934@syzkaller.appspotmail.com
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f941d3e41d ]
There are systems in which non-wakeup GPEs fire during the "noirq"
suspend stage of suspending devices and that effectively prevents the
system that tries to suspend to idle from entering any low-power
state at all. If the offending GPE fires regularly and often enough,
the system appears to be suspended, but in fact it is in a tight loop
over "noirq" suspend and "noirq" resume of devices all the time.
To prevent that from happening, disable all non-wakeup GPEs except
for the EC GPE for suspend-to-idle (the EC GPE is special, because
on some systems it has to be enabled for power button wakeup events
to be generated as expected).
Fixes: 147a7d9d25 (ACPI / PM: Do not reconfigure GPEs for suspend-to-idle)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201987
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49ad712afa ]
The Image Signal Processor found on Cherry Trail devices is brought up in
D0 state on devices which have camera sensors attached to it. The ISP will
not enter D3 state again without some massaging of its registers beforehand
and the ISP not being in D3 state blocks the SoC from entering S0ix modes.
There was a driver for the ISP in drivers/staging but that got removed
again because it never worked. It does not seem likely that a real
driver for the ISP will be added to the mainline kernel anytime soon.
This commit adds a dummy driver which contains the necessary magic from
the staging driver to powerdown the ISP, so that Cherry Trail devices where
the ISP is used will properly use S0ix modes when suspended.
Together with other recent S0ix related fixes this allows S0ix modes to
be entered on e.g. a Chuwi Hi8 Pro and a HP x2 210.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196915
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1c6ca3c6d ]
It is possible to observe hung_task complaints when system goes to
suspend-to-idle state:
# echo freeze > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
sd 0:0:0:0: [sda] Synchronizing SCSI cache
INFO: task bash:1569 blocked for more than 120 seconds.
Not tainted 4.19.0-rc3_+ #687
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
bash D 0 1569 604 0x00000000
Call Trace:
? __schedule+0x1fe/0x7e0
schedule+0x28/0x80
suspend_devices_and_enter+0x4ac/0x750
pm_suspend+0x2c0/0x310
Register a PM notifier to disable the detector on suspend and re-enable
back on wakeup.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b7960cace ]
In cases where queryinfo fails, we have cases in cifs (vers=1.0)
where with backupuid mounts we retry the query info with findfirst.
This doesn't work to some NetApp servers which don't support
WindowsXP (and later) infolevel 261 (SMB_FIND_FILE_ID_FULL_DIR_INFO)
so in this case use other info levels (in this case it will usually
be level 257, SMB_FIND_FILE_DIRECTORY_INFO).
(Also fixes some indentation)
See kernel bugzilla 201435
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd18bffca3 ]
A VMEnter that VMFails (as opposed to VMExits) does not touch host
state beyond registers that are explicitly noted in the VMFail path,
e.g. EFLAGS. Host state does not need to be loaded because VMFail
is only signaled for consistency checks that occur before the CPU
starts to load guest state, i.e. there is no need to restore any
state as nothing has been modified. But in the case where a VMFail
is detected by hardware and not by KVM (due to deferring consistency
checks to hardware), KVM has already loaded some amount of guest
state. Luckily, "loaded" only means loaded to KVM's software model,
i.e. vmcs01 has not been modified. So, unwind our software model to
the pre-VMEntry host state.
Not restoring host state in this VMFail path leads to a variety of
failures because we end up with stale data in vcpu->arch, e.g. CR0,
CR4, EFER, etc... will all be out of sync relative to vmcs01. Any
significant delta in the stale data is all but guaranteed to crash
L1, e.g. emulation of SMEP, SMAP, UMIP, WP, etc... will be wrong.
An alternative to this "soft" reload would be to load host state from
vmcs12 as if we triggered a VMExit (as opposed to VMFail), but that is
wildly inconsistent with respect to the VMX architecture, e.g. an L1
VMM with separate VMExit and VMFail paths would explode.
Note that this approach does not mean KVM is 100% accurate with
respect to VMX hardware behavior, even at an architectural level
(the exact order of consistency checks is microarchitecture specific).
But 100% emulation accuracy isn't the goal (with this patch), rather
the goal is to be consistent in the information delivered to L1, e.g.
a VMExit should not fall-through VMENTER, and a VMFail should not jump
to HOST_RIP.
This technically reverts commit "5af4157388ad (KVM: nVMX: Fix mmu
context after VMLAUNCH/VMRESUME failure)", but retains the core
aspects of that patch, just in an open coded form due to the need to
pull state from vmcs01 instead of vmcs12. Restoring host state
resolves a variety of issues introduced by commit "4f350c6dbcb9
(kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly)",
which remedied the incorrect behavior of treating VMFail like VMExit
but in doing so neglected to restore arch state that had been modified
prior to attempting nested VMEnter.
A sample failure that occurs due to stale vcpu.arch state is a fault
of some form while emulating an LGDT (due to emulated UMIP) from L1
after a failed VMEntry to L3, in this case when running the KVM unit
test test_tpr_threshold_values in L1. L0 also hits a WARN in this
case due to a stale arch.cr4.UMIP.
L1:
BUG: unable to handle kernel paging request at ffffc90000663b9e
PGD 276512067 P4D 276512067 PUD 276513067 PMD 274efa067 PTE 8000000271de2163
Oops: 0009 [#1] SMP
CPU: 5 PID: 12495 Comm: qemu-system-x86 Tainted: G W 4.18.0-rc2+ #2
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:native_load_gdt+0x0/0x10
...
Call Trace:
load_fixmap_gdt+0x22/0x30
__vmx_load_host_state+0x10e/0x1c0 [kvm_intel]
vmx_switch_vmcs+0x2d/0x50 [kvm_intel]
nested_vmx_vmexit+0x222/0x9c0 [kvm_intel]
vmx_handle_exit+0x246/0x15a0 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x850/0x1830 [kvm]
kvm_vcpu_ioctl+0x3a1/0x5c0 [kvm]
do_vfs_ioctl+0x9f/0x600
ksys_ioctl+0x66/0x70
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x4f/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
L0:
WARNING: CPU: 2 PID: 3529 at arch/x86/kvm/vmx.c:6618 handle_desc+0x28/0x30 [kvm_intel]
...
CPU: 2 PID: 3529 Comm: qemu-system-x86 Not tainted 4.17.2-coffee+ #76
Hardware name: Intel Corporation Kabylake Client platform/KBL S
RIP: 0010:handle_desc+0x28/0x30 [kvm_intel]
...
Call Trace:
kvm_arch_vcpu_ioctl_run+0x863/0x1840 [kvm]
kvm_vcpu_ioctl+0x3a1/0x5c0 [kvm]
do_vfs_ioctl+0x9f/0x5e0
ksys_ioctl+0x66/0x70
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x49/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 5af4157388 (KVM: nVMX: Fix mmu context after VMLAUNCH/VMRESUME failure)
Fixes: 4f350c6dbc (kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly)
Cc: Jim Mattson <jmattson@google.com>
Cc: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca1721c5be ]
On Apple machines, plugging-in or unplugging the power triggers a GPE
for the EC. Since these machines expose an SBS device, this GPE ends
up triggering the acpi_sbs_callback(). This in turn tries to get the
status of the SBS charger. However, on MBP13,* and MBP14,* machines,
performing the smbus-read operation to get the charger's status triggers
the EC's GPE again. The result is an endless re-triggering and handling
of that GPE, consuming significant CPU resources (> 50% in irq).
In the end this is quite similar to commit 3031cddea6 (ACPI / SBS:
Don't assume the existence of an SBS charger), except that on the above
machines a status of all 1's is returned. And like there, we just want
ignore the charger here.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198169
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0a2e73e50 ]
Without this usbip fails on a machine with devices
that lexicographically come after vhci_hcd.
ie.
$ ls -l /sys/devices/platform
...
drwxr-xr-x. 4 root root 0 Sep 19 16:21 serial8250
-rw-r--r--. 1 root root 4096 Sep 19 23:50 uevent
drwxr-xr-x. 6 root root 0 Sep 20 13:15 vhci_hcd.0
drwxr-xr-x. 4 root root 0 Sep 19 16:22 w83627hf.656
Because it detects 'w83627hf.656' as another vhci_hcd controller,
and then fails to be able to talk to it.
Note: this doesn't actually fix usbip's support for multiple
controllers... that's still broken for other reasons
("vhci_hcd.0" is hardcoded in a string macro), but is enough to
actually make it work on the above machine.
See also:
https://bugzilla.redhat.com/show_bug.cgi?id=1631148
Cc: Jonathan Dieter <jdieter@gmail.com>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Tested-by: Jonathan Dieter <jdieter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6862fdf220 ]
"S3C2410 PM Suspend Memory CRC" feature (controlled by
SAMSUNG_PM_CHECK config option) is incompatible with highmem
(uses phys_to_virt() instead of proper mapping) which is used by
the majority of Exynos boards. The issue manifests itself in OOPS
on affected boards, i.e. on Odroid-U3 I got the following one:
Unable to handle kernel paging request at virtual address f0000000
pgd = 1c0f9bb4
[f0000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[<c0458034>] (crc32_le) from [<c0121f8c>] (s3c_pm_makecheck+0x34/0x54)
[<c0121f8c>] (s3c_pm_makecheck) from [<c0121efc>] (s3c_pm_run_res+0x74/0x8c)
[<c0121efc>] (s3c_pm_run_res) from [<c0121ecc>] (s3c_pm_run_res+0x44/0x8c)
[<c0121ecc>] (s3c_pm_run_res) from [<c01210b8>] (exynos_suspend_enter+0x64/0x148)
[<c01210b8>] (exynos_suspend_enter) from [<c018893c>] (suspend_devices_and_enter+0x9ec/0xe74)
[<c018893c>] (suspend_devices_and_enter) from [<c0189534>] (pm_suspend+0x770/0xc04)
[<c0189534>] (pm_suspend) from [<c0186ce8>] (state_store+0x6c/0xcc)
[<c0186ce8>] (state_store) from [<c09db434>] (kobj_attr_store+0x14/0x20)
[<c09db434>] (kobj_attr_store) from [<c02fa63c>] (sysfs_kf_write+0x4c/0x50)
[<c02fa63c>] (sysfs_kf_write) from [<c02f97a4>] (kernfs_fop_write+0xfc/0x1e4)
[<c02f97a4>] (kernfs_fop_write) from [<c027b198>] (__vfs_write+0x2c/0x140)
[<c027b198>] (__vfs_write) from [<c027b418>] (vfs_write+0xa4/0x160)
[<c027b418>] (vfs_write) from [<c027b5d8>] (ksys_write+0x40/0x8c)
[<c027b5d8>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Add PLAT_S3C24XX, ARCH_S3C64XX and ARCH_S5PV210 dependencies to
SAMSUNG_PM_CHECK config option to hide it on Exynos platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54a58185bf ]
Some drivers, for example, QCOM's qdf2xxx, set groups[gpio].name only
when gpio is valid, and leave invalid gpio names as null.
If we want to access the sys node "pinconf-groups",
pinctrl_get_group_selector() -> get_group_name() may return a null
pointer if group_selector is invalid, then the below Kernel panic
would happen since strcmp() uses this null pointer to do comparison.
Unable to handle kernel NULL pointer dereference at ss 00000000
el:Internal error: Oops: 9600000[ 143.080279]
SMP
CPU: 19 PID: 2493 Comm: read_all Tainted: G O
.aarch64 #1
Hardware name: HXT Semiconductor HXT REP-2 System
PC is at strcmp+0x18/0x154
LR is at pinctrl_get_group_selector+0x6c/0xe8
Process read_all (pid: 2493, stack limit =
Call trace:
Exception stack
strcmp+0x18/0x154
pin_config_group_get+0x64/0xd8
pinconf_generic_dump_one+0xd8/0x1c0
pinconf_generic_dump_pins+0x94/0xc8
pinconf_groups_show+0xb4/0x104
seq_read+0x178/0x464
full_proxy_read+0x6c/0xac
__vfs_read+0x58/0x178
vfs_read+0x94/0x164
SyS_read+0x60/0xc0
__sys_trace_return+0x0/0x4
--[ end trace]--
Kernel panic - not syncing: Fatal exception
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb1ce2350 ]
When console device is rebinded, console_setup() is called again.
But marking it as __init means that function will be clear after boot is
complete. If console device is binded again console_setup() is not found
and error "Unable to handle kernel paging request at virtual address"
is reported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d704967f4 ]
cgroup v2 path field is PATH_MAX which is too large, this is placing too
much pressure on memory allocation for people with many rules doing
cgroup v1 classid matching, side effects of this are bug reports like:
https://bugzilla.kernel.org/show_bug.cgi?id=200639
This patch registers a new revision that shrinks the cgroup path to 512
bytes, which is the same approach we follow in similar extensions that
have a path field.
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae7d1247d8 ]
In functions snd_soc_get_volsw_sx() or snd_soc_put_volsw_sx(),
if the result of (min + max) is negative, then fls() returns
signed integer with value as 32. This leads to signed integer
overflow as complete operation is considered as signed integer.
UBSAN: Undefined behaviour in sound/soc/soc-ops.c:382:50
signed integer overflow:
-2147483648 - 1 cannot be represented in type 'int'
Call trace:
[<ffffff852f746fe4>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffff852f746fe4>] dump_stack+0xec/0x158 lib/dump_stack.c:51
[<ffffff852f7b5f3c>] ubsan_epilogue+0x18/0x50 lib/ubsan.c:164
[<ffffff852f7b6840>] handle_overflow+0xf8/0x130 lib/ubsan.c:195
[<ffffff852f7b68f0>] __ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:211
[<ffffff85307971a0>] snd_soc_get_volsw_sx+0x1a8/0x1f8 sound/soc/soc-ops.c:382
Typecast the operation to unsigned int to fix the issue.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d20c8abb2 ]
https://bugzilla.kernel.org/show_bug.cgi?id=200951
These is a NULL pointer dereference issue reported in bugzilla:
Hi,
in the setup there is a SATA SSD connected to a SATA-to-USB bridge.
The disc is "Samsung SSD 850 PRO 256G" which supports TRIM.
There are four partitions:
sda1: FAT /boot
sda2: F2FS /
sda3: F2FS /home
sda4: F2FS
The bridge is ASMT1153e which uses the "uas" driver.
There is no TRIM pass-through, so, when mounting it reports:
mounting with "discard" option, but the device does not support discard
The USB host is USB3.0 and UASP capable. It is the one on RK3399.
Given this everything works fine, except there is no TRIM support.
In order to enable TRIM a new UDEV rule is added [1]:
/etc/udev/rules.d/10-sata-bridge-trim.rules:
ACTION=="add|change", ATTRS{idVendor}=="174c", ATTRS{idProduct}=="55aa", SUBSYSTEM=="scsi_disk", ATTR{provisioning_mode}="unmap"
After reboot any F2FS write hangs forever and dmesg reports:
Unable to handle kernel NULL pointer dereference
Also tested on a x86_64 system: works fine even with TRIM enabled.
same disc
same bridge
different usb host controller
different cpu architecture
not root filesystem
Regards,
Vicenç.
[1] Post #5 in https://bbs.archlinux.org/viewtopic.php?id=236280
Unable to handle kernel NULL pointer dereference at virtual address 000000000000003e
Mem abort info:
ESR = 0x96000004
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000626e3122
[000000000000003e] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
Modules linked in: overlay snd_soc_hdmi_codec rc_cec dw_hdmi_i2s_audio dw_hdmi_cec snd_soc_simple_card snd_soc_simple_card_utils snd_soc_rockchip_i2s rockchip_rga snd_soc_rockchip_pcm rockchipdrm videobuf2_dma_sg v4l2_mem2mem rtc_rk808 videobuf2_memops analogix_dp videobuf2_v4l2 videobuf2_common dw_hdmi dw_wdt cec rc_core videodev drm_kms_helper media drm rockchip_thermal rockchip_saradc realtek drm_panel_orientation_quirks syscopyarea sysfillrect sysimgblt fb_sys_fops dwmac_rk stmmac_platform stmmac pwm_bl squashfs loop crypto_user gpio_keys hid_kensington
CPU: 5 PID: 957 Comm: nvim Not tainted 4.19.0-rc1-1-ARCH #1
Hardware name: Sapphire-RK3399 Board (DT)
pstate: 00000005 (nzcv daif -PAN -UAO)
pc : update_sit_entry+0x304/0x4b0
lr : update_sit_entry+0x108/0x4b0
sp : ffff00000ca13bd0
x29: ffff00000ca13bd0 x28: 000000000000003e
x27: 0000000000000020 x26: 0000000000080000
x25: 0000000000000048 x24: ffff8000ebb85cf8
x23: 0000000000000253 x22: 00000000ffffffff
x21: 00000000000535f2 x20: 00000000ffffffdf
x19: ffff8000eb9e6800 x18: ffff8000eb9e6be8
x17: 0000000007ce6926 x16: 000000001c83ffa8
x15: 0000000000000000 x14: ffff8000f602df90
x13: 0000000000000006 x12: 0000000000000040
x11: 0000000000000228 x10: 0000000000000000
x9 : 0000000000000000 x8 : 0000000000000000
x7 : 00000000000535f2 x6 : ffff8000ebff3440
x5 : ffff8000ebff3440 x4 : ffff8000ebe3a6c8
x3 : 00000000ffffffff x2 : 0000000000000020
x1 : 0000000000000000 x0 : ffff8000eb9e5800
Process nvim (pid: 957, stack limit = 0x0000000063a78320)
Call trace:
update_sit_entry+0x304/0x4b0
f2fs_invalidate_blocks+0x98/0x140
truncate_node+0x90/0x400
f2fs_remove_inode_page+0xe8/0x340
f2fs_evict_inode+0x2b0/0x408
evict+0xe0/0x1e0
iput+0x160/0x260
do_unlinkat+0x214/0x298
__arm64_sys_unlinkat+0x3c/0x68
el0_svc_handler+0x94/0x118
el0_svc+0x8/0xc
Code: f9400800 b9488400 36080140 f9400f01 (387c4820)
---[ end trace a0f21a307118c477 ]---
The reason is it is possible to enable discard flag on block queue via
UDEV, but during mount, f2fs will initialize se->discard_map only if
this flag is set, once the flag is set after mount, f2fs may dereference
NULL pointer on se->discard_map.
So this patch does below changes to fix this issue:
- initialize and update se->discard_map all the time.
- don't clear DISCARD option if device has no QUEUE_FLAG_DISCARD flag
during mount.
- don't issue small discard on zoned block device.
- introduce some functions to enhance the readability.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ce3ebe973 ]
In the corner case where the gpio driver probe fails, for whatever
reason, the suspend and resume handlers will still be called as they
have to be registered as syscore operations. This applies as well when
no probe was called while the driver has been built in the kernel.
Nicolas tracked this in :
https://bugzilla.kernel.org/show_bug.cgi?id=200905
Therefore, add a failsafe in these function, and test if a proper probe
succeeded and the driver is functional.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abf7b30d7f ]
In the Cirrus driver, the regular clean-up code also performs the clean-up
of a failed initialization. If the fbdev's framebuffer was not initialized,
the clean-up will fail within drm_framebuffer_unregister_private. Booting
with cirrus.bpp=16 triggers this bug.
The framebuffer is currently stored directly within struct cirrus_fbdev. To
fix the bug, we turn it into a pointer that is only set for initialized
framebuffers. The fbdev's clean-up code skips uninitialized framebuffers.
The memory for struct drm_framebuffer is allocated dynamically. This requires
additional error handling within cirrusfb_create. The framebuffer clean-up is
now performed by drm_framebuffer_put, which also frees the data strcuture's
memory.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1101822
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20180720112743.27159-1-tzimmermann@suse.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18915b5873 ]
The ext4 fstrim implementation uses the block bitmaps to find free space
that can be discarded. If we haven't replayed the journal, the bitmaps
will be stale and we absolutely *cannot* use stale metadata to zap the
underlying storage.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
YueHaibing