[ Upstream commit 86bd0c4a2a ]
The Exynos UFS controller only supports scatter/gather list elements that
are aligned on a 4 KiB boundary. Fix DMA alignment in case PAGE_SIZE !=
4096. Rename UFSHCD_QUIRK_ALIGN_SG_WITH_PAGE_SIZE into
UFSHCD_QUIRK_4KB_DMA_ALIGNMENT.
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Fixes: 2b2bfc8aa5 ("scsi: ufs: Introduce a quirk to allow only page-aligned sg entries")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9d27c6be5 ]
The MIPI DCS specification demands that brightness values are sent in
big endian byte order. It also states that one parameter (i.e. one byte)
shall be sent/received for 8 bit wide values, and two parameters shall
be used for values that are between 9 and 16 bits wide.
Add new functions to properly handle 16-bit brightness in big endian,
since the two 8- and 16-bit cases are distinct from each other.
[richard: use separate functions instead of switch/case]
[richard: split into 16-bit component]
Fixes: 1a9d759331 ("drm/dsi: Implement DCS set/get display brightness")
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Link: 754affd62d
[richard: fix 16-bit brightness_get]
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Tested-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116224909.23884-2-mailingradian@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abc40122d9 ]
In the event that the topology requests resources that have not been
created by the system (because they are typically not represented in
dpu_mdss_cfg ^1), the resource(s) in global_state (in this case DSC
blocks, until their allocation/assignment is being sanity-checked in
"drm/msm/dpu: Reject topologies for which no DSC blocks are available")
remain NULL but will still be returned out of
dpu_rm_get_assigned_resources, where the caller expects to get an array
containing num_blks valid pointers (but instead gets these NULLs).
To prevent this from happening, where null-pointer dereferences
typically result in a hard-to-debug platform lockup, num_blks shouldn't
increase past NULL blocks and will print an error and break instead.
After all, max_blks represents the static size of the maximum number of
blocks whereas the actual amount varies per platform.
^1: which can happen after a git rebase ended up moving additions to
_dpu_cfg to a different struct which has the same patch context.
Fixes: bb00a452d6 ("drm/msm/dpu: Refactor resource manager")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/517636/
Link: https://lore.kernel.org/r/20230109231556.344977-1-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf22ef78f2 ]
The problem is that base sched hasn't been assigned yet at this moment,
causing something like "ring=0" all the time from trace.
mpv:cs0-3473 [002] ..... 129.047431: amdgpu_cs: ring=0, dw=48, fences=0
mpv:cs0-3473 [002] ..... 129.089125: amdgpu_cs: ring=0, dw=48, fences=0
mpv:cs0-3473 [002] ..... 129.130987: amdgpu_cs: ring=0, dw=48, fences=0
mpv:cs0-3473 [002] ..... 129.172478: amdgpu_cs: ring=0, dw=48, fences=0
Fixes: 4624459c84 ("drm/amdgpu: add gang submit frontend v6")
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ee0fe7fa3 ]
Although the "dma_chan" pointer occupies more or equal space compared
to "*dma_chan", the allocation size should use the size of variable
itself.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 01ef7dbffb ("ALSA: hda - Update CA0132 codec to load DSP firmware binary")
Signed-off-by: Alexey V. Vissarionov <gremlin@altlinux.org>
Link: https://lore.kernel.org/r/20230117111522.GA15213@altlinux.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f5fab1b6c ]
clang warning:
drivers/scsi/qla2xxx/qla_edif_bsg.h:93:12: warning: field remote_pid
within 'struct app_pinfo_req' is less aligned than 'port_id_t' and is
usually due to 'struct app_pinfo_req' being packed, which can lead to
unaligned accesses [-Wunaligned-access]
port_id_t remote_pid;
^
2 warnings generated.
Remove u32 field in remote_pid to silence warning.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 7ebb336e45 ("scsi: qla2xxx: edif: Add start + stop bsgs")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41e5afe51f ]
In large environment, it is possible to experience command timeout and
escalation of path recovery. Currently the driver does not track the number
of exchanges/commands sent to FW. If there is a delay for commands at the
head of the queue, then this will create back pressure for commands at the
back of the queue.
Check for exchange availability before command submission.
Fixes: 89c72f4245 ("scsi: qla2xxx: Add IOCB resource tracking")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df993fced2 ]
The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.
With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.
Fixes: c54619b0bf ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-2-1f8e0770798b@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca8fd8c16a ]
A user complained that the ftsteutates driver was displaying
bogus values since its introduction. This happens because the
sensor measurements need to be scaled in order to produce
meaningful results:
- the fan speed needs to be multiplied by 60 since its in RPS
- the temperature is in degrees celsius and needs an offset of 64
- the voltage is in 1/256 of 3.3V
The offical datasheet says the voltage needs to be divided by 256,
but this is likely an off-by-one-error, since even the BIOS
devides by 255 (otherwise 3.3V could not be measured).
The voltage channels additionally need a board-specific multiplier,
however this can be done by the driver since its board-specific.
The reason the missing scaling of measurements is the way Fujitsu
used this driver when it was still out-of-tree. Back then, all
scaling was done in userspace by libsensors, even the generic one.
Tested on a Fujitsu DS3401-B1.
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20221224041855.83981-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fe2a8f40c ]
A null-ptr-deref is triggered when it tries to destroy the workqueue in
vkms->output.composer_workq in vkms_release().
KASAN: null-ptr-deref in range [0x0000000000000118-0x000000000000011f]
CPU: 5 PID: 17193 Comm: modprobe Not tainted 6.0.0-11331-gd465bff130bf #24
RIP: 0010:destroy_workqueue+0x2f/0x710
...
Call Trace:
<TASK>
? vkms_config_debugfs_init+0x50/0x50 [vkms]
__devm_drm_dev_alloc+0x15a/0x1c0 [drm]
vkms_init+0x245/0x1000 [vkms]
do_one_initcall+0xd0/0x4f0
do_init_module+0x1a4/0x680
load_module+0x6249/0x7110
__do_sys_finit_module+0x140/0x200
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
The reason is that an OOM happened which triggers the destroy of the
workqueue, however, the workqueue is alloced in the later process,
thus a null-ptr-deref happened. A simple call graph is shown as below:
vkms_init()
vkms_create()
devm_drm_dev_alloc()
__devm_drm_dev_alloc()
devm_drm_dev_init()
devm_add_action_or_reset()
devm_add_action() # an error happened
devm_drm_dev_init_release()
drm_dev_put()
kref_put()
drm_dev_release()
vkms_release()
destroy_workqueue() # null-ptr-deref happened
vkms_modeset_init()
vkms_output_init()
vkms_crtc_init() # where the workqueue get allocated
Fix this by checking if composer_workq is NULL before passing it to
the destroy_workqueue() in vkms_release().
Fixes: 6c234fe37c ("drm/vkms: Implement CRC debugfs API")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221101065156.41584-3-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d0b368b9d ]
A memory leak was reported after the vkms module install failed.
unreferenced object 0xffff88810bc28520 (size 16):
comm "modprobe", pid 9662, jiffies 4298009455 (age 42.590s)
hex dump (first 16 bytes):
01 01 00 64 81 88 ff ff 00 00 dc 0a 81 88 ff ff ...d............
backtrace:
[<00000000e7561ff8>] kmalloc_trace+0x27/0x60
[<000000000b1954a0>] 0xffffffffc45200a9
[<00000000abbf1da0>] do_one_initcall+0xd0/0x4f0
[<000000001505ee87>] do_init_module+0x1a4/0x680
[<00000000958079ad>] load_module+0x6249/0x7110
[<00000000117e4696>] __do_sys_finit_module+0x140/0x200
[<00000000f74b12d2>] do_syscall_64+0x35/0x80
[<000000008fc6fcde>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
The reason is that the vkms_init() returns without checking the return
value of vkms_create(), and if the vkms_create() failed, the config
allocated at the beginning of vkms_init() is leaked.
vkms_init()
config = kmalloc(...) # config allocated
...
return vkms_create() # vkms_create failed and config is leaked
Fix this problem by checking return value of vkms_create() and free the
config if error happened.
Fixes: 2df7af93fd ("drm/vkms: Add vkms_config type")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221101065156.41584-2-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ecff954c3 ]
A problem about insmod megachips-stdpxxxx-ge-b850v3-fw.ko failed is
triggered with the following log given:
[ 4497.981497] Error: Driver 'stdp4028-ge-b850v3-fw' is already registered, aborting...
insmod: ERROR: could not insert module megachips-stdpxxxx-ge-b850v3-fw.ko: Device or resource busy
The reason is that stdpxxxx_ge_b850v3_init() returns i2c_add_driver()
directly without checking its return value, if i2c_add_driver() failed,
it returns without calling i2c_del_driver() on the previous i2c driver,
resulting the megachips-stdpxxxx-ge-b850v3-fw can never be installed
later.
A simple call graph is shown as below:
stdpxxxx_ge_b850v3_init()
i2c_add_driver(&stdp4028_ge_b850v3_fw_driver)
i2c_add_driver(&stdp2690_ge_b850v3_fw_driver)
i2c_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without delete stdp4028_ge_b850v3_fw_driver
Fix by calling i2c_del_driver() on stdp4028_ge_b850v3_fw_driver when
i2c_add_driver() returns error.
Fixes: fcfa0ddc18 ("drm/bridge: Drivers for megachips-stdpxxxx-ge-b850v3-fw (LVDS-DP++)")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221108091226.114524-1-yuancan@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
