[ Upstream commit 8c8e60fb86 ]
Commit 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling
brcmf_bus_started()") changed the initialization order of the brcmfmac
SDIO driver. Unfortunately since brcmf_sdiod_intr_register() is now
called before the sdiodev->bus_if initialization, it reads the wrong
chip ID and fails to initialize the GPIO on brcm43362. Thus the chip
cannot send interrupts and fails to probe:
[ 12.517023] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
[ 12.531214] ieee80211 phy0: brcmf_bus_started: failed: -110
[ 12.536976] ieee80211 phy0: brcmf_attach: dongle is not responding: err=-110
[ 12.566467] brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
Initialize the bus interface earlier to ensure that
brcmf_sdiod_intr_register() properly sets up the OOB interrupt.
BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908438
Fixes: 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling brcmf_bus_started()")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a68fa5f9 ]
The rate mask is used to tell firmware the supported rate depends on
negotiation. We loop 2 times for all VHT/HT 2SS rate mask first, and then
only keep the part according to chip's NSS.
This commit fixes the logic error of '&' operations for VHT/HT rate, and
we should run this logic before adding legacy rate.
To access HT MCS map, index 0/1 represent MCS 0-7/8-15 respectively. Use
NL80211_BAND_xxx is incorrect, so fix it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba8b3b6bd ]
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
We might see a trace like below
[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c
Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: dc405152bb ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51f57b01e4 ]
JBD2_REC_ERR flag used to indicate the errno has been updated when jbd2
aborted, and then __ext4_abort() and ext4_handle_error() can invoke
panic if ERRORS_PANIC is specified. But if the journal has been aborted
with zero errno, jbd2_journal_abort() didn't set this flag so we can
no longer panic. Fix this by always record the proper errno in the
journal superblock.
Fixes: 4327ba52af ("ext4, jbd2: ensure entering into panic after recording an error in superblock")
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191204124614.45424-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc420c6cee ]
Kmemleak relies on specific symbols to register the read only data
during init (e.g. __start_ro_after_init).
Trying to build an XIP kernel on arm results in the linking error
reported below because when this option is selected read only data
after init are not allowed since .data is read only (.rodata).
arm-linux-gnueabihf-ld: mm/kmemleak.o: in function `kmemleak_init':
kmemleak.c:(.init.text+0x148): undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x14c):
undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x150):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x156):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x162):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x16a):
undefined reference to `__start_ro_after_init'
linux/Makefile:1078: recipe for target 'vmlinux' failed
Fix the issue enabling kmemleak only on non XIP kernels.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfb6cd1e65 ]
Looking through old emails in my INBOX, I came across a patch from Luis
Henriques that attempted to fix a race of two stat tracers registering the
same stat trace (extremely unlikely, as this is done in the kernel, and
probably doesn't even exist). The submitted patch wasn't quite right as it
needed to deal with clean up a bit better (if two stat tracers were the
same, it would have the same files).
But to make the code cleaner, all we needed to do is to keep the
all_stat_sessions_mutex held for most of the registering function.
Link: http://lkml.kernel.org/r/1410299375-20068-1-git-send-email-luis.henriques@canonical.com
Fixes: 002bb86d8d ("tracing/ftrace: separate events tracing and stats tracing engine")
Reported-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 965c94f309 ]
An ioda_pe for each VF is allocated in pnv_pci_sriov_enable() before
the pci_dev for the VF is created. We need to set the pe->pdev pointer
at some point after the pci_dev is created. Currently we do that in:
pcibios_bus_add_device()
pnv_pci_dma_dev_setup() (via phb->ops.dma_dev_setup)
/* fixup is done here */
pnv_pci_ioda_dma_dev_setup() (via pnv_phb->dma_dev_setup)
The fixup needs to be done before setting up DMA for for the VF's PE,
but there's no real reason to delay it until this point. Move the
fixup into pnv_pci_ioda_fixup_iov() so the ordering is:
pcibios_add_device()
pnv_pci_ioda_fixup_iov() (via ppc_md.pcibios_fixup_sriov)
pcibios_bus_add_device()
...
This isn't strictly required, but it's a slightly more logical place
to do the fixup and it simplifies pnv_pci_dma_dev_setup().
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-4-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 953c4a08df ]
o call skb_reset_network_header() before hdlc->xmit()
o change skb proto to HDLC (0x0019) before hdlc->xmit()
o call dev_queue_xmit_nit() before hdlc->xmit()
This changes make it possible to trace (tcpdump) outgoing layer2
(ETH_P_HDLC) packets
Additionally call skb_reset_network_header() after each skb_push() /
skb_pull().
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15fb05fd28 ]
UDF 2.60 standard states in section 2.2.14.2:
A partition with Access Type 3 (rewritable) shall define a Freed
Space Bitmap or a Freed Space Table, see 2.3.3. All other partitions
shall not define a Freed Space Bitmap or a Freed Space Table.
Rewritable partitions are used on media that require some form of
preprocessing before re-writing data (for example legacy MO). Such
partitions shall use Access Type 3.
Overwritable partitions are used on media that do not require
preprocessing before overwriting data (for example: CD-RW, DVD-RW,
DVD+RW, DVD-RAM, BD-RE, HD DVD-Rewritable). Such partitions shall
use Access Type 4.
however older versions of the standard didn't have this wording and
there are tools out there that create UDF filesystems with rewritable
partitions but that don't contain a Freed Space Bitmap or a Freed Space
Table on media that does not require pre-processing before overwriting a
block. So instead of forcing media with rewritable partition read-only,
base this decision on presence of a Freed Space Bitmap or a Freed Space
Table.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Fixes: b085fbe2ef ("udf: Fix crash during mount")
Link: https://lore.kernel.org/linux-fsdevel/20200112144735.hj2emsoy4uwsouxz@pali
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4cf7aa57e ]
Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.
This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.
Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e3002837 ]
The parent clk for gmac clk ctrl has to be gmac_main_clk (125MHz) instead
of dpll_gmac_ck (1GHz). This is caused incorrect CPSW MDIO operation.
Hence, fix it.
Fixes: dffa9051d5 ('clk: ti: dra7: add new clkctrl data')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e45330e3 ]
Without any form of coordination, any case where multiple allocations
from the same mempool are needed at a time to make forward progress can
deadlock under memory pressure.
This is the case for struct bio_post_read_ctx, as one can be allocated
to decrypt a Merkle tree page during fsverity_verify_bio(), which itself
is running from a post-read callback for a data bio which has its own
struct bio_post_read_ctx.
Fix this by freeing the first bio_post_read_ctx before calling
fsverity_verify_bio(). This works because verity (if enabled) is always
the last post-read step.
This deadlock can be reproduced by trying to read from an encrypted
verity file after reducing NUM_PREALLOC_POST_READ_CTXS to 1 and patching
mempool_alloc() to pretend that pool->alloc() always fails.
Note that since NUM_PREALLOC_POST_READ_CTXS is actually 128, to actually
hit this bug in practice would require reading from lots of encrypted
verity files at the same time. But it's theoretically possible, as N
available objects isn't enough to guarantee forward progress when > N/2
threads each need 2 objects at a time.
Fixes: 22cfe4b48c ("ext4: add fs-verity read support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20191231181222.47684-1-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a09decff5c ]
If the journal is dirty when the filesystem is mounted, jbd2 will replay
the journal but the journal superblock will not be updated by
journal_reset() because JBD2_ABORT flag is still set (it was set in
journal_init_common()). This is problematic because when a new transaction
is then committed, it will be recorded in block 1 (journal->j_tail was set
to 1 in journal_reset()). If unclean shutdown happens again before the
journal superblock is updated, the new recorded transaction will not be
replayed during the next mount (because of stale sb->s_start and
sb->s_sequence values) which can lead to filesystem corruption.
Fixes: 85e0c4e89c ("jbd2: if the journal is aborted then don't allow update of the log tail")
Signed-off-by: Kai Li <li.kai4@h3c.com>
Link: https://lore.kernel.org/r/20200111022542.5008-1-li.kai4@h3c.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b64a650f0 ]
It was observed[1] on arm64 that __builtin_strlen led to an infinite
loop in the get_size selftest. This is because __builtin_strlen (and
other builtins) may sometimes result in a call to the C library
function. The C library implementation of strlen uses an IFUNC
resolver to load the most efficient strlen implementation for the
underlying machine and hence has a PLT indirection even for static
binaries. Because this binary avoids the C library startup routines,
the PLT initialization never happens and hence the program gets stuck
in an infinite loop.
On x86_64 the __builtin_strlen just happens to expand inline and avoid
the call but that is not always guaranteed.
Further, while testing on x86_64 (Fedora 31), it was observed that the
test also failed with a segfault inside write() because the generated
code for the write function in glibc seems to access TLS before the
syscall (probably due to the cancellation point check) and fails
because TLS is not initialised.
To mitigate these problems, this patch reduces the interface with the
C library to just the syscall function. The syscall function still
sets errno on failure, which is undesirable but for now it only
affects cases where syscalls fail.
[1] https://bugs.linaro.org/show_bug.cgi?id=5479
Signed-off-by: Siddhesh Poyarekar <siddhesh@gotplt.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2052d032c0 ]
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f0898 ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c1ed62ae0 ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/usb/gadget/udc/core.c, 1175:
kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/core.c, 1195:
mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 212:
debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2114:
devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.
To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f42e4b337b ]
The sizeof is currently on args.src and args.dst and should be on
*args.src and *args.dst. Fortunately these sizes just so happen
to be the same size so it worked, however, this should be fixed
and it also cleans up static analysis warnings
Addresses-Coverity: ("sizeof not portable")
Fixes: f268307ec7 ("nouveau: simplify nouveau_dmem_migrate_vma")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc3a8b295e ]
Why it does not work at the moment:
- num_chipselect sets the number of cs-gpios that are in the DT.
This comes from drivers/spi/spi.c
- num_chipselect gets set with devm_spi_register_controller, that is
called in drivers/spi/spi.c
- devm_spi_register_controller got called after num_chipselect has
been used.
How this commit fixes the issue:
- devm_spi_register_controller gets called before num_chipselect is
being used.
Fixes: c7a4025995 ("spi: lpspi: use the core way to implement cs-gpio function")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20191204141312.1411251-1-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df5e984c8b ]
guest vm gets 0xffffffff when reading RCC_DEV0_EPF0_STRAP0,
as a consequence, the rev_id and external_rev_id are wrong.
workaround it by hardcoding the rev_id to 0, which is the default value.
v2. add comment in the code
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b74351287d ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
kernel/irq/manage.c, 523:
synchronize_irq in disable_irq
drivers/uio/uio_dmem_genirq.c, 140:
disable_irq in uio_dmem_genirq_irqcontrol
drivers/uio/uio_dmem_genirq.c, 134:
_raw_spin_lock_irqsave in uio_dmem_genirq_irqcontrol
synchronize_irq() can sleep at runtime.
To fix this bug, disable_irq() is called without holding the spinlock.
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218094405.6009-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b8651aac1 ]
The compilation error is redeclaration showed as following:
In file included from ../../../include/linux/limits.h:6,
from /usr/include/x86_64-linux-gnu/bits/local_lim.h:38,
from /usr/include/x86_64-linux-gnu/bits/posix1_lim.h:161,
from /usr/include/limits.h:183,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/limits.h:194,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/syslimits.h:7,
from /usr/lib/gcc/x86_64-linux-gnu/8/include-fixed/limits.h:34,
from ../../../include/linux/raid/pq.h:30,
from algos.c:14:
../../../include/linux/types.h:114:15: error: conflicting types for ‘int64_t’
typedef s64 int64_t;
^~~~~~~
In file included from /usr/include/stdint.h:34,
from /usr/lib/gcc/x86_64-linux-gnu/8/include/stdint.h:9,
from /usr/include/inttypes.h:27,
from ../../../include/linux/raid/pq.h:29,
from algos.c:14:
/usr/include/x86_64-linux-gnu/bits/stdint-intn.h:27:19: note: previous \
declaration of ‘int64_t’ was here
typedef __int64_t int64_t;
Fixes: 54d50897d5 ("linux/kernel.h: split *_MAX and *_MIN macros into <linux/limits.h>")
Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83db9ef56 ]
The IXP4xx driver was initializing the MDIO bus before even
probing, in the callbacks supposed to be used for setting up
the module itself, and with the side effect of trying to
register the MDIO bus as soon as this module was loaded or
compiled into the kernel whether the device was discovered
or not.
This does not work with multiplatform environments.
To get rid of this: set up the MDIO bus from the probe()
callback and remove it in the remove() callback. Rename
the probe() and remove() calls to reflect the most common
conventions.
Since there is a bit of checking for the ethernet feature
to be present in the MDIO registering function, making the
whole module not even be registered if we can't find an
MDIO bus, we need something similar: register the MDIO
bus when the corresponding ethernet is probed, and
return -EPROBE_DEFER on the other interfaces until this
happens. If no MDIO bus is present on any of the
registered interfaces we will eventually bail out.
None of the platforms I've seen has e.g. MDIO on EthB
and only uses EthC, there is always a Ethernet hardware
on the NPE (B, C) that has the MDIO bus, we just might
have to wait for it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548f0b9a5f ]
This fixes build errors of all sorts.
Also, emit .exit.text unconditionally.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffc2760bcf ]
Fix a couple of issues with the way we map and copy the vendor string:
- we map only 2 bytes, which usually works since you get at least a
page, but if the vendor string happens to cross a page boundary,
a crash will result
- only call early_memunmap() if early_memremap() succeeded, or we will
call it with a NULL address which it doesn't like,
- while at it, switch to early_memremap_ro(), and array indexing rather
than pointer dereferencing to read the CHAR16 characters.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Matthew Garrett <mjg59@google.com>
Cc: linux-efi@vger.kernel.org
Fixes: 5b83683f32 ("x86: EFI runtime service support")
Link: https://lkml.kernel.org/r/20200103113953.9571-5-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a23680594d ]
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b57cea922 ]
Currently when the low level driver notifies Pkey, GID, and port change
events they are notified to the registered handlers in the order they are
registered.
IB core and other ULPs such as IPoIB are interested in GID, LID, Pkey
change events.
Since all GID queries done by ULPs are serviced by IB core, and the IB
core deferes cache updates to a work queue, it is possible for other
clients to see stale cache data when they handle their own events.
For example, the below call tree shows how ipoib will call
rdma_query_gid() concurrently with the update to the cache sitting in the
WQ.
mlx5_ib_handle_event()
ib_dispatch_event()
ib_cache_event()
queue_work() -> slow cache update
[..]
ipoib_event()
queue_work()
[..]
work handler
ipoib_ib_dev_flush_light()
__ipoib_ib_dev_flush()
ipoib_dev_addr_changed_valid()
rdma_query_gid() <- Returns old GID, cache not updated.
Move all the event dispatch to a work queue so that the cache update is
always done before any clients are notified.
Fixes: f35faa4ba9 ("IB/core: Simplify ib_query_gid to always refer to cache")
Link: https://lore.kernel.org/r/20191212113024.336702-3-leon@kernel.org
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6d061d617 ]
In module_add_modinfo_attrs() if sysfs_create_file() fails
on the first iteration of the loop (so i = 0), we forget to
free the modinfo_attrs.
Fixes: bc6f2a757d ("kernel/module: Fix mem leak in module_add_modinfo_attrs")
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb6d42061a ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/media/platform/sti/bdisp/bdisp-hw.c, 385:
msleep in bdisp_hw_reset
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 341:
bdisp_hw_reset in bdisp_device_run
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 317:
_raw_spin_lock_irqsave in bdisp_device_run
To fix this bug, msleep() is replaced with udelay().
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbc55341b9 ]
In __fpu__restore_sig(), fpu_fpregs_owner_ctx needs to be reset if the
FPU state was not fully restored. Otherwise the following may happen (on
the same CPU):
Task A Task B fpu_fpregs_owner_ctx
*active* A.fpu
__fpu__restore_sig()
ctx switch load B.fpu
*active* B.fpu
fpregs_lock()
copy_user_to_fpregs_zeroing()
copy_kernel_to_xregs() *modify*
copy_user_to_xregs() *fails*
fpregs_unlock()
ctx switch skip loading B.fpu,
*active* B.fpu
In the success case, fpu_fpregs_owner_ctx is set to the current task.
In the failure case, the FPU state might have been modified by loading
the init state.
In this case, fpu_fpregs_owner_ctx needs to be reset in order to ensure
that the FPU state of the following task is loaded from saved state (and
not skipped because it was the previous state).
Reset fpu_fpregs_owner_ctx after a failure during restore occurred, to
ensure that the FPU state for the next task is always loaded.
The problem was debugged-by Yu-cheng Yu <yu-cheng.yu@intel.com>.
[ bp: Massage commit message. ]
Fixes: 5f409e20b7 ("x86/fpu: Defer FPU state load until return to userspace")
Reported-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191220195906.plk6kpmsrikvbcfn@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e36eaf94be ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/gpio/gpio-grgpio.c, 261:
request_irq in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 255:
_raw_spin_lock_irqsave in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 318:
free_irq in grgpio_irq_unmap
drivers/gpio/gpio-grgpio.c, 299:
_raw_spin_lock_irqsave in grgpio_irq_unmap
request_irq() and free_irq() can sleep at runtime.
To fix these bugs, request_irq() and free_irq() are called without
holding the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218132605.10594-1-baijiaju1990@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8daeaea99c ]
The "mali_0" or "mali_1" clock trees should not be updated while the
clock is running. Enforce this by setting CLK_SET_RATE_GATE on the
"mali_0" and "mali_1" gates. This makes the CCF switch to the "mali_1"
tree when "mali_0" is currently active and vice versa, which is exactly
what the vendor driver does when updating the frequency of the mali
clock.
This fixes a potential hang when changing the GPU frequency at runtime.
Fixes: 74e1f2521f ("clk: meson: meson8b: add the GPU clock tree")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b5b9997b3 ]
On pseries there is a bug with adding hotplugged devices to an IOMMU
group. For a number of dumb reasons fixing that bug first requires
re-working how VFs are configured on PowerNV. For background, on
PowerNV we use the pcibios_sriov_enable() hook to do two things:
1. Create a pci_dn structure for each of the VFs, and
2. Configure the PHB's internal BARs so the MMIO range for each VF
maps to a unique PE.
Roughly speaking a PE is the hardware counterpart to a Linux IOMMU
group since all the devices in a PE share the same IOMMU table. A PE
also defines the set of devices that should be isolated in response to
a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all
MMIO and DMA traffic to and from devicein the PE is blocked by the
root complex until the PE is recovered by the OS.
The requirement to block MMIO causes a giant headache because the P8
PHB generally uses a fixed mapping between MMIO addresses and PEs. As
a result we need to delay configuring the IOMMU groups for device
until after MMIO resources are assigned. For physical devices (i.e.
non-VFs) the PE assignment is done in pcibios_setup_bridge() which is
called immediately after the MMIO resources for downstream
devices (and the bridge's windows) are assigned. For VFs the setup is
more complicated because:
a) pcibios_setup_bridge() is not called again when VFs are activated, and
b) The pci_dev for VFs are created by generic code which runs after
pcibios_sriov_enable() is called.
The work around for this is a two step process:
1. A fixup in pcibios_add_device() is used to initialised the cached
pe_number in pci_dn, then
2. A bus notifier then adds the device to the IOMMU group for the PE
specified in pci_dn->pe_number.
A side effect fixing the pseries bug mentioned in the first paragraph
is moving the fixup out of pcibios_add_device() and into
pcibios_bus_add_device(), which is called much later. This results in
step 2. failing because pci_dn->pe_number won't be initialised when
the bus notifier is run.
We can fix this by removing the need for the fixup. The PE for a VF is
known before the VF is even scanned so we can initialise
pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately,
moving the initialisation causes two problems:
1. We trip the WARN_ON() in the current fixup code, and
2. The EEH core clears pdn->pe_number when recovering a VF and
relies on the fixup to correctly re-set it.
The only justification for either of these is a comment in
eeh_rmv_device() suggesting that pdn->pe_number *must* be set to
IODA_INVALID_PE in order for the VF to be scanned. However, this
comment appears to have no basis in reality. Both bugs can be fixed by
just deleting the code.
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191028085424.12006-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66d9f5214c ]
The prescaler works as parent rate divided by (PRES + 1) (is_pres_direct == 1)
It does not work in the way of parent rate shifted to the right by (PRES + 1),
which means division by 2^(PRES + 1) (is_pres_direct == 0)
Thus is_pres_direct must be enabled for this SoC, to make the right computation.
This field was added in
commit 45b0668211 ("clk: at91: fix programmable clock for sama5d2")
SAM9X60 has the same field as SAMA5D2 in the PCK
Fixes: 01e2113de9 ("clk: at91: add sam9x60 pmc driver")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lkml.kernel.org/r/1575977088-16781-1-git-send-email-eugen.hristev@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1948dcf0f9 ]
The Allwinner camera sensor interface has a different definition of
[HV]sync. While the timing diagram uses the names HSYNC and VSYNC,
the note following the diagram and register names use HREF and VREF.
Combined they imply the hardware uses either [HV]REF or inverted
[HV]SYNC. There are also registers to set horizontal skip lengths
in pixels and vertical skip lengths in lines, also known as back
porches.
Fix the polarity handling by using the opposite polarity flag for
the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better
match the hardware register description.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9e6d5dbd ]
The CLK_POL field specifies whether data is sampled on the falling or
rising edge of PCLK, not whether the data lines are active high or low.
Evidence of this can be found in the timing diagram labeled "horizontal
size setting and pixel clock timing".
Fix the setting by checking the correct flag, V4L2_MBUS_PCLK_SAMPLE_RISING.
While at it, reorder the three polarity flag checks so HSYNC and VSYNC
are grouped together.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 249b286171 ]
On Allwinner SoCs, some high memory bandwidth devices do DMA directly
over the memory bus (called MBUS), instead of the system bus. These
devices include the CSI camera sensor interface, video (codec) engine,
display subsystem, etc.. The memory bus has a different addressing
scheme without the DRAM starting offset.
Deal with this using the "interconnects" property from the device tree,
or if that is not available, set dev->dma_pfn_offset to PHYS_PFN_OFFSET.
Fixes: 577bbf23b7 ("media: sunxi: Add A10 CSI driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1451d5ae35 ]
This driver supports both the mt9v032 (color) and the mt9v022 (mono)
sensors. Depending on which sensor is used, the format from the sensor is
different. The format.code inside the dev struct holds this information.
The enum mbus and enum frame sizes need to take into account both type of
sensors, not just the color one. To solve this, use the format.code in
these functions instead of the hardcoded bayer color format (which is only
used for mt9v032).
[Sakari Ailus: rewrapped commit message]
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e3df204f9 ]
The variable _rate is by ov5640_compute_sys_clk() which returns
zero if the PLL exceeds 1GHz. Unfortunately, the check to see
if the max PLL1 output is checking 'rate' and not '_rate' and
'rate' does not ever appear to be 0.
This patch changes the check against the returned value of
'_rate' to determine if the PLL1 output exceeds 1GHz.
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ab987c42 ]
We can have two cases, when it comes to "zap" fw. Either the fw
requires zap fw to take the GPU out of secure mode at boot, or it does
not and we can write RBBM_SECVID_TRUST_CNTL directly. Previously we
decided based on whether zap fw load succeeded, but this is not a great
plan because:
1) we could have zap fw in the filesystem on a device where it is not
required
2) we could have the inverse case
Instead, shift to deciding based on whether we have a 'zap-shader' node
in dt. In practice, there is only one device (currently) with upstream
dt that does not use zap (cheza), and it already has a /delete-node/ for
the zap-shader node.
Fixes: abccb9fe32 ("drm/msm/a6xx: Add zap shader load")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ce18249af ]
When configuring the frame memory window, the last column and row
numbers are written to the column resp. page address registers. These
numbers are thus one less than the actual window width resp. height.
While this is handled correctly in mipi_dbi_fb_dirty() since commit
03ceb1c8df ("drm/tinydrm: Fix setting of the column/page end
addresses."), it is not in mipi_dbi_blank(). The latter still forgets
to subtract one when calculating the most significant bytes of the
column and row numbers, thus programming wrong values when the display
width or height is a multiple of 256.
Fixes: 02dd95fe31 ("drm/tinydrm: Add MIPI DBI support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230130604.31006-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
