[ Upstream commit c673ec61ad ]
When CONFIG_XEN_BALLOON_MEMORY_HOTPLUG is not defined
reserve_additional_memory() will set balloon_stats.target_pages to a
wrong value in case there are still some ballooned pages allocated via
alloc_xenballooned_pages().
This will result in balloon_process() no longer be triggered when
ballooned pages are freed in batches.
Reported-by: Nicholas Tsirakis <niko.tsirakis@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa2ac657f9 ]
Objects allocated by xen_blkif_alloc come from the 'blkif_cache' kmem
cache. This cache is destoyed when xen-blkif is unloaded so it is
necessary to wait for the deferred free routine used for such objects to
complete. This necessity was missed in commit 14855954f6 "xen-blkback:
allow module to be cleanly unloaded". This patch fixes the problem by
taking/releasing extra module references in xen_blkif_alloc/free()
respectively.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0539ad0b22 ]
The s390 CPU Measurement sampling facility has an overflow condition
which fires when all entries in a SBD are used.
The measurement alert interrupt is triggered and reads out all samples
in this SDB. It then tests the successor SDB, if this SBD is not full,
the interrupt handler does not read any samples at all from this SDB
The design waits for the hardware to fill this SBD and then trigger
another meassurement alert interrupt.
This scheme works nicely until
an perf_event_overflow() function call discards the sample due to
a too high sampling rate.
The interrupt handler has logic to read out a partially filled SDB
when the perf event overflow condition in linux common code is met.
This causes the CPUM sampling measurement hardware and the PMU
device driver to operate on the same SBD's trailer entry.
This should not happen.
This can be seen here using this trace:
cpumsf_pmu_add: tear:0xb5286000
hw_perf_event_update: sdbt 0xb5286000 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 1. interrupt
hw_perf_event_update: sdbt 0xb5286008 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 2. interrupt
... this goes on fine until...
hw_perf_event_update: sdbt 0xb5286068 full 1 over 0 flush_all:0
perf_push_sample1: overflow
one or more samples read from the IRQ handler are rejected by
perf_event_overflow() and the IRQ handler advances to the next SDB
and modifies the trailer entry of a partially filled SDB.
hw_perf_event_update: sdbt 0xb5286070 full 0 over 0 flush_all:1
timestamp: 14:32:52.519953
Next time the IRQ handler is called for this SDB the trailer entry shows
an overflow count of 19 missed entries.
hw_perf_event_update: sdbt 0xb5286070 full 1 over 19 flush_all:1
timestamp: 14:32:52.970058
Remove access to a follow on SDB when event overflow happened.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39d4a501a9 ]
Function perf_event_ever_overflow() and perf_event_account_interrupt()
are called every time samples are processed by the interrupt handler.
However function perf_event_account_interrupt() has checks to avoid being
flooded with interrupts (more then 1000 samples are received per
task_tick). Samples are then dropped and a PERF_RECORD_THROTTLED is
added to the perf data. The perf subsystem limit calculation is:
maximum sample frequency := 100000 --> 1 samples per 10 us
task_tick = 10ms = 10000us --> 1000 samples per task_tick
The work flow is
measurement_alert() uses SDBT head and each SBDT points to 511
SDB pages, each with 126 sample entries. After processing 8 SBDs
and for each valid sample calling:
perf_event_overflow()
perf_event_account_interrupts()
there is a considerable amount of samples being dropped, especially when
the sample frequency is very high and near the 100000 limit.
To avoid the high amount of samples being dropped near the end of a
task_tick time frame, increment the sampling interval in case of
dropped events. The CPU Measurement sampling facility on the s390
supports only intervals, specifiing how many CPU cycles have to be
executed before a sample is generated. Increase the interval when the
samples being generated hit the task_tick limit.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1da4bd9f9d ]
Fix the lookup method on the dynamic root directory such that creation
calls, such as mkdir, open(O_CREAT), symlink, etc. fail with EOPNOTSUPP
rather than failing with some odd error (such as EEXIST).
lookup() itself tries to create automount directories when it is invoked.
These are cached locally in RAM and not committed to storage.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebfcd8955c ]
The socket read/write helpers only look at the file O_NONBLOCK. not
the iocb IOCB_NOWAIT flag. This breaks users like preadv2/pwritev2
and io_uring that rely on not having the file itself marked nonblocking,
but rather the iocb itself.
Cc: netdev@vger.kernel.org
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5b5da96da ]
Gadget driver should always use config_ep_by_speed() to initialize
usb_ep struct according to usb device's operating speed. Otherwise,
usb_ep struct may be wrong if usb devcie's operating speed is changed.
The key point in this patch is that we want to make sure the desc pointer
in usb_ep struct will be set to NULL when gadget is disconnected.
This will force it to call config_ep_by_speed() to correctly initialize
usb_ep struct based on the new operating speed when gadget is
re-connected later.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37a68eab4c ]
Place the declaration of struct nouveau_conn_atom above that of
struct nouveau_connector. This commit makes no changes to the moved
block what so ever, it just moves it up a bit.
This is a preparation patch to fix some issues with connector handling
on pre nv50 displays (which do not use atomic modesetting).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fee92f2577 ]
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->chap_dma_pool' double freed
drivers/scsi/qla4xxx/ql4_os.c:8856 qla4xxx_probe_adapter() warn: 'ha->fw_ddb_dma_pool' double freed
Fixes: afaf5a2d34 ("[SCSI] Initial Commit of qla4xxx")
Link: https://lore.kernel.org/r/20191203094421.hw7ex7qr3j2rbsmx@kili.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd1de5830a ]
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad0990 ("scsi: qla2xxx: Fix N2N link re-connect")
Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com
Acked-by: Quinn Tran <qutran@marvell.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2030abddec ]
If RoCE PDUs being sent or received contain pad bytes, then the iCRC
is miscalculated, resulting in PDUs being emitted by RXE with an incorrect
iCRC, as well as ingress PDUs being dropped due to erroneously detecting
a bad iCRC in the PDU. The fix is to include the pad bytes, if any,
in iCRC computations.
Note: This bug has caused broken on-the-wire compatibility with actual
hardware RoCE devices since the soft-RoCE driver was first put into the
mainstream kernel. Fixing it will create an incompatibility with the
original soft-RoCE devices, but is necessary to be compatible with real
hardware devices.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Steve Wise <larrystevenwise@gmail.com>
Link: https://lore.kernel.org/r/20191203020319.15036-2-larrystevenwise@gmail.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcbccaf2ed ]
Make the AFS dynamic root superblock R/W so that SELinux can set the
security label on it. Without this, upgrades to, say, the Fedora
filesystem-afs RPM fail if afs is mounted on it because the SELinux label
can't be (re-)applied.
It might be better to make it possible to bypass the R/O check for LSM
label application through setxattr.
Fixes: 4d673da145 ("afs: Support the AFS dynamic root")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: selinux@vger.kernel.org
cc: linux-security-module@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bd0160d12 ]
afs_find_server tries to find a server that has an address that
matches the transport address of an rxrpc peer. The code assumes
that the transport address is always ipv6, with ipv4 represented
as ipv4 mapped addresses, but that's not the case. If the transport
family is AF_INET, srx->transport.sin6.sin6_addr.s6_addr32[] will
be beyond the actual ipv4 address and will always be 0, and all
ipv4 addresses will be seen as matching.
As a result, the first ipv4 address seen on any server will be
considered a match, and the server returned may be the wrong one.
One of the consequences is that callbacks received over ipv4 will
only be correctly applied for the server that happens to have the
first ipv4 address on the fs_addresses4 list. Callbacks over ipv4
from all other servers are dropped, causing the client to serve stale
data.
This is fixed by looking at the transport family, and comparing ipv4
addresses based on a sockaddr_in structure rather than a sockaddr_in6.
Fixes: d2ddc776a4 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42a6b25e67 ]
Right now devfreq_dev_release will print a warning and abort the rest of
the cleanup if the devfreq instance is not part of the global
devfreq_list. But this is a valid scenario, for example it can happen if
the governor can't be found or on any other init error that happens
after device_register.
Initialize devfreq->node to an empty list head in devfreq_add_device so
that list_del becomes a safe noop inside devfreq_dev_release and we can
continue the rest of the cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7cc792d00 ]
The devfreq_notifier_call functions will update scaling_min_freq and
scaling_max_freq when the OPP table is updated.
If fetching the maximum frequency fails then scaling_max_freq remains
set to zero which is confusing. Set to ULONG_MAX instead so we don't
need special handling for this case in other places.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e876e710ed ]
Notifier callbacks shouldn't return negative errno but one of the
NOTIFY_OK/DONE/BAD values.
The OPP core will ignore return values from notifiers but returning a
value that matches NOTIFY_STOP_MASK will stop the notification chain.
Fix by always returning NOTIFY_OK.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fd229c478 ]
As of commit b9ddd50911 ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
Fixes: 69780a3bbc ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a51d9f8fe7 ]
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e807535da ]
When security violation from new vbios happens, data fabric is
risky to stop working. So prevent the direct access to DF
mmFabricConfigAccessControl from the new vbios and onwards.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c869e494ef ]
If an error occurs on one of the ios used for creating an
association, the creating routine has error paths that are
invoked by the command failure and the error paths will free
up the controller resources created to that point.
But... the io was ultimately determined by an asynchronous
completion routine that detected the error and which
unconditionally invokes the error_recovery path which calls
delete_association. Delete association deletes all outstanding
io then tears down the controller resources. So the
create_association thread can be running in parallel with
the error_recovery thread. What was seen was the LLDD received
a call to delete a queue, causing the LLDD to do a free of a
resource, then the transport called the delete queue again
causing the driver to repeat the free call. The second free
routine corrupted the allocator. The transport shouldn't be
making the duplicate call, and the delete queue is just one
of the resources being freed.
To fix, it is realized that the create_association path is
completely serialized with one command at a time. So the
failed io completion will always be seen by the create_association
path and as of the failure, there are no ios to terminate and there
is no reason to be manipulating queue freeze states, etc.
The serialized condition stays true until the controller is
transitioned to the LIVE state. Thus the fix is to change the
error recovery path to check the controller state and only
invoke the teardown path if not already in the CONNECTING state.
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 863fbae929 ]
In nvme-fc: it's possible to have connected active controllers
and as no references are taken on the LLDD, the LLDD can be
unloaded. The controller would enter a reconnect state and as
long as the LLDD resumed within the reconnect timeout, the
controller would resume. But if a namespace on the controller
is the root device, allowing the driver to unload can be problematic.
To reload the driver, it may require new io to the boot device,
and as it's no longer connected we get into a catch-22 that
eventually fails, and the system locks up.
Fix this issue by taking a module reference for every connected
controller (which is what the core layer did to the transport
module). Reference is cleared when the controller is removed.
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40ecab5512 ]
Commit 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org
Fixes: 39ce8150a0 ("pinctrl: baytrail: Serialize all register access")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a902c0f31 ]
GTP default hashtable size is 1024 and userspace could set specific
hashtable size with IFLA_GTP_PDP_HASHSIZE. If hashtable size is set to 0
from userspace, hashtable will not work and panic will occur.
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94dc550a50 ]
ipv4_pdp_find() is called in TX packet path of GTP.
ipv4_pdp_find() internally uses gtp->tid_hash to lookup pdp context.
In the current code, gtp->tid_hash and gtp->addr_hash are freed by
->dellink(), which is gtp_dellink().
But gtp_dellink() would be called while packets are processing.
So, gtp_dellink() should not free gtp->tid_hash and gtp->addr_hash.
Instead, dev->priv_destructor() would be used because this callback
is called after all packet processing safely.
Test commands:
ip link add veth1 type veth peer name veth2
ip a a 172.0.0.1/24 dev veth1
ip link set veth1 up
ip a a 172.99.0.1/32 dev lo
gtp-link add gtp1 &
gtp-tunnel add gtp1 v1 200 100 172.99.0.2 172.0.0.2
ip r a 172.99.0.2/32 dev gtp1
ip link set gtp1 mtu 1500
ip netns add ns2
ip link set veth2 netns ns2
ip netns exec ns2 ip a a 172.0.0.2/24 dev veth2
ip netns exec ns2 ip link set veth2 up
ip netns exec ns2 ip a a 172.99.0.2/32 dev lo
ip netns exec ns2 ip link set lo up
ip netns exec ns2 gtp-link add gtp2 &
ip netns exec ns2 gtp-tunnel add gtp2 v1 100 200 172.99.0.1 172.0.0.1
ip netns exec ns2 ip r a 172.99.0.1/32 dev gtp2
ip netns exec ns2 ip link set gtp2 mtu 1500
hping3 172.99.0.2 -2 --flood &
ip link del gtp1
Splat looks like:
[ 72.568081][ T1195] BUG: KASAN: use-after-free in ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.568916][ T1195] Read of size 8 at addr ffff8880b9a35d28 by task hping3/1195
[ 72.569631][ T1195]
[ 72.569861][ T1195] CPU: 2 PID: 1195 Comm: hping3 Not tainted 5.5.0-rc1 #199
[ 72.570547][ T1195] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 72.571438][ T1195] Call Trace:
[ 72.571764][ T1195] dump_stack+0x96/0xdb
[ 72.572171][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.572761][ T1195] print_address_description.constprop.5+0x1be/0x360
[ 72.573400][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.573971][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.574544][ T1195] __kasan_report+0x12a/0x16f
[ 72.575014][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.575593][ T1195] kasan_report+0xe/0x20
[ 72.576004][ T1195] ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.576577][ T1195] gtp_build_skb_ip4+0x199/0x1420 [gtp]
[ ... ]
[ 72.647671][ T1195] BUG: unable to handle page fault for address: ffff8880b9a35d28
[ 72.648512][ T1195] #PF: supervisor read access in kernel mode
[ 72.649158][ T1195] #PF: error_code(0x0000) - not-present page
[ 72.649849][ T1195] PGD a6c01067 P4D a6c01067 PUD 11fb07067 PMD 11f939067 PTE 800fffff465ca060
[ 72.652958][ T1195] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 72.653834][ T1195] CPU: 2 PID: 1195 Comm: hping3 Tainted: G B 5.5.0-rc1 #199
[ 72.668062][ T1195] RIP: 0010:ipv4_pdp_find.isra.12+0x86/0x170 [gtp]
[ ... ]
[ 72.679168][ T1195] Call Trace:
[ 72.679603][ T1195] gtp_build_skb_ip4+0x199/0x1420 [gtp]
[ 72.681915][ T1195] ? ipv4_pdp_find.isra.12+0x170/0x170 [gtp]
[ 72.682513][ T1195] ? lock_acquire+0x164/0x3b0
[ 72.682966][ T1195] ? gtp_dev_xmit+0x35e/0x890 [gtp]
[ 72.683481][ T1195] gtp_dev_xmit+0x3c2/0x890 [gtp]
[ ... ]
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94a6d9fb88 ]
gtp_genl_dump_pdp() is ->dumpit() callback of GTP module and it is used
to dump pdp contexts. it would be re-executed because of dump packet size.
If dump packet size is too big, it saves current dump pointer
(gtp interface pointer, bucket, TID value) then it restarts dump from
last pointer.
Current GTP code allows adding zero TID pdp context but dump code
ignores zero TID value. So, last dump pointer will not be found.
In addition, this patch adds missing rcu_read_lock() in
gtp_genl_dump_pdp().
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f85e6267c ]
Backport of commit fdfc5c8594 ("tcp: remove empty skb from
write queue in error cases") in linux-4.14 stable triggered
various bugs. One of them has been fixed in commit ba2ddb43f2
("tcp: Don't dequeue SYN/FIN-segments from write-queue"), but
we still have crashes in some occasions.
Root-cause is that when tcp_sendmsg() has allocated a fresh
skb and could not append a fragment before being blocked
in sk_stream_wait_memory(), tcp_write_xmit() might be called
and decide to send this fresh and empty skb.
Sending an empty packet is not only silly, it might have caused
many issues we had in the past with tp->packets_out being
out of sync.
Fixes: c65f7f00c5 ("[TCP]: Simplify SKB data portion allocation with NETIF_F_SG.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dbd76e79a upstream.
Michal Kubecek and Firo Yang did a very nice analysis of crashes
happening in __inet_lookup_established().
Since a TCP socket can go from TCP_ESTABLISH to TCP_LISTEN
(via a close()/socket()/listen() cycle) without a RCU grace period,
I should not have changed listeners linkage in their hash table.
They must use the nulls protocol (Documentation/RCU/rculist_nulls.txt),
so that a lookup can detect a socket in a hash list was moved in
another one.
Since we added code in commit d296ba60d8 ("soreuseport: Resolve
merge conflict for v4/v6 ordering fix"), we have to add
hlist_nulls_add_tail_rcu() helper.
Fixes: 3b24d854cb ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Firo Yang <firo.yang@suse.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/netdev/20191120083919.GH27852@unicorn.suse.cz/
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
[stable-4.19: we also need to update code in __inet_lookup_listener() and
inet6_lookup_listener() which has been removed in 5.0-rc1.]
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f3f2364ea1 ]
phylink requires the MAC to report when its link status changes when
operating in inband modes. Failure to report link status changes
means that phylink has no idea when the link events happen, which
results in either the network interface's carrier remaining up or
remaining permanently down.
For example, with a fiber module, if the interface is brought up and
link is initially established, taking the link down at the far end
will cut the optical power. The SFP module's LOS asserts, we
deactivate the link, and the network interface reports no carrier.
When the far end is brought back up, the SFP module's LOS deasserts,
but the MAC may be slower to establish link. If this happens (which
in my tests is a certainty) then phylink never hears that the MAC
has established link with the far end, and the network interface is
stuck reporting no carrier. This means the interface is
non-functional.
Avoiding the link interrupt when we have phylink is basically not
an option, so remove the !port->phylink from the test.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b01b1d9b2 ]
GTP RX packet path lookups pdp context with TID. If duplicate TID pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, TID value should be unique.
GTP TX packet path lookups pdp context with ms_addr. If duplicate ms_addr pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, ms_addr value should be unique.
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f081042d12 ]
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
So disable the neigh confirm for vxlan and geneve pmtu update.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: a93bf0ff44 ("vxlan: update skb dst pmtu on tx path")
Fixes: 52a589d51f ("geneve: update skb dst pmtu on tx path")
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Tested-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d42df46d6 ]
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8247a79efa ]
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although vti and vti6 are immune to this problem because they are IFF_NOARP
interfaces, as Guillaume pointed. There is still no sense to confirm neighbour
here.
v5: Update commit description.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a1592bcb1 ]
When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No Change.
v4: Update commit description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 0dec879f63 ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP")
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Tested-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07dc35c6e3 ]
Add a new function skb_dst_update_pmtu_no_confirm() for callers who need
update pmtu but should not do neighbor confirm.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
