[ Upstream commit 9d5dcefb7b ]
As the comments in this patch say, if we tune and find all phases are
valid it's _almost_ as bad as no phases being found valid. Probably
all phases are not really reliable but we didn't detect where the
unreliable place is. That means we'll essentially be guessing and
hoping we get a good phase.
This is not just a problem in theory. It was causing real problems on
a real board. On that board, most often phase 10 is found as the only
invalid phase, though sometimes 10 and 11 are invalid and sometimes
just 11. Some percentage of the time, however, all phases are found
to be valid. When this happens, the current logic will decide to use
phase 11. Since phase 11 is sometimes found to be invalid, this is a
bad choice. Sure enough, when phase 11 is picked we often get mmc
errors later in boot.
I have seen cases where all phases were found to be valid 3 times in a
row, so increase the retry count to 10 just to be extra sure.
Fixes: 415b5a75da ("mmc: sdhci-msm: Add platform_execute_tuning implementation")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28b0865714 ]
When the returned speed from __ethtool_get_link_ksettings() is
SPEED_UNKNOWN this will lead to reporting a wrong speed and width for
providers that uses ib_get_eth_speed(), fix that by defaulting the
netdev_speed to SPEED_1000 in case the returned value from
__ethtool_get_link_ksettings() is SPEED_UNKNOWN.
Fixes: d41861942f ("IB/core: Add generic function to extract IB speed from netdev")
Link: https://lore.kernel.org/r/20200902124304.170912-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53de092f47 ]
It was discovered that sdparm will fail when attempting to disable write
cache on a SATA disk connected via libsas.
In the ATA command set the write cache state is controlled through the SET
FEATURES operation. This is roughly corresponds to MODE SELECT in SCSI and
the latter command is what is used in the SCSI-ATA translation layer. A
subtle difference is that a MODE SELECT carries data whereas SET FEATURES
is defined as a non-data command in ATA.
Set the DMA data direction to DMA_NONE if the requested ATA command is
identified as non-data.
[mkp: commit desc]
Fixes: fa1c1e8f1e ("[SCSI] Add SATA support to libsas")
Link: https://lore.kernel.org/r/1598426666-54544-1-git-send-email-luojiaxing@huawei.com
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81dbbb417d ]
According to the Reference Manual, the correct size is 512 MiB.
Without this fix, probing the QSPI fails:
fsl-quadspi 1550000.spi: ioremap failed for resource
[mem 0x40000000-0x7fffffff]
fsl-quadspi 1550000.spi: Freescale QuadSPI probe failed
fsl-quadspi: probe of 1550000.spi failed with error -12
Fixes: 85f8ee78ab ("ARM: dts: ls1021a: Add support for QSPI with ls1021a SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d26e9a028 ]
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree but never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 5cb8b0fa55 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7dfee6768 ]
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree, they were never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 739f85bba5 ("ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Support for phys switch id ndo added for representors and if
we do not have representors there is no need to support it.
Since each port return different switch id supporting this
block support for creating bond over PFs and attaching to bridge
in legacy mode.
This bug doesn't exist upstream as the code got refactored and the
netdev api is totally different.
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 96e97bc07e ]
napi_disable() makes sure to set the NAPI_STATE_NPSVC bit to prevent
netpoll from accessing rings before init is complete. However, the
same is not done for fresh napi instances in netif_napi_add(),
even though we expect NAPI instances to be added as disabled.
This causes crashes during driver reconfiguration (enabling XDP,
changing the channel count) - if there is any printk() after
netif_napi_add() but before napi_enable().
To ensure memory ordering is correct we need to use RCU accessors.
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes: 2d8bff1269 ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a63866c8b ]
syzbot is reporting hung task at nbd_ioctl() [1], for there are two
problems regarding TIPC's connectionless socket's shutdown() operation.
----------
#include <fcntl.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <linux/nbd.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
const int fd = open("/dev/nbd0", 3);
alarm(5);
ioctl(fd, NBD_SET_SOCK, socket(PF_TIPC, SOCK_DGRAM, 0));
ioctl(fd, NBD_DO_IT, 0); /* To be interrupted by SIGALRM. */
return 0;
}
----------
One problem is that wait_for_completion() from flush_workqueue() from
nbd_start_device_ioctl() from nbd_ioctl() cannot be completed when
nbd_start_device_ioctl() received a signal at wait_event_interruptible(),
for tipc_shutdown() from kernel_sock_shutdown(SHUT_RDWR) from
nbd_mark_nsock_dead() from sock_shutdown() from nbd_start_device_ioctl()
is failing to wake up a WQ thread sleeping at wait_woken() from
tipc_wait_for_rcvmsg() from sock_recvmsg() from sock_xmit() from
nbd_read_stat() from recv_work() scheduled by nbd_start_device() from
nbd_start_device_ioctl(). Fix this problem by always invoking
sk->sk_state_change() (like inet_shutdown() does) when tipc_shutdown() is
called.
The other problem is that tipc_wait_for_rcvmsg() cannot return when
tipc_shutdown() is called, for tipc_shutdown() sets sk->sk_shutdown to
SEND_SHUTDOWN (despite "how" is SHUT_RDWR) while tipc_wait_for_rcvmsg()
needs sk->sk_shutdown set to RCV_SHUTDOWN or SHUTDOWN_MASK. Fix this
problem by setting sk->sk_shutdown to SHUTDOWN_MASK (like inet_shutdown()
does) when the socket is connectionless.
[1] https://syzkaller.appspot.com/bug?id=3fe51d307c1f0a845485cf1798aa059d12bf18b2
Reported-by: syzbot <syzbot+e36f41d207137b5d12f7@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3106ecb43a ]
With disabling bh in the whole sctp_get_port_local(), when
snum == 0 and too many ports have been used, the do-while
loop will take the cpu for a long time and cause cpu stuck:
[ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s!
[ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940
[ ] Call Trace:
[ ] _raw_spin_lock+0xc1/0xd0
[ ] sctp_get_port_local+0x527/0x650 [sctp]
[ ] sctp_do_bind+0x208/0x5e0 [sctp]
[ ] sctp_autobind+0x165/0x1e0 [sctp]
[ ] sctp_connect_new_asoc+0x355/0x480 [sctp]
[ ] __sctp_connect+0x360/0xb10 [sctp]
There's no need to disable bh in the whole function of
sctp_get_port_local. So fix this cpu stuck by removing
local_bh_disable() called at the beginning, and using
spin_lock_bh() instead.
The same thing was actually done for inet_csk_get_port() in
Commit ea8add2b19 ("tcp/dccp: better use of ephemeral
ports in bind()").
Thanks to Marcelo for pointing the buggy code out.
v1->v2:
- use cond_resched() to yield cpu to other tasks if needed,
as Eric noticed.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d3b990b7f3 ]
This patch fixes two main problems seen when removing NetLabel
mappings: memory leaks and potentially extra audit noise.
The memory leaks are caused by not properly free'ing the mapping's
address selector struct when free'ing the entire entry as well as
not properly cleaning up a temporary mapping entry when adding new
address selectors to an existing entry. This patch fixes both these
problems such that kmemleak reports no NetLabel associated leaks
after running the SELinux test suite.
The potentially extra audit noise was caused by the auditing code in
netlbl_domhsh_remove_entry() being called regardless of the entry's
validity. If another thread had already marked the entry as invalid,
but not removed/free'd it from the list of mappings, then it was
possible that an additional mapping removal audit record would be
generated. This patch fixes this by returning early from the removal
function when the entry was previously marked invalid. This change
also had the side benefit of improving the code by decreasing the
indentation level of large chunk of code by one (accounting for most
of the diffstat).
Fixes: 63c4168874 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping")
Reported-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de1b0ee490 ]
If a driver leaves the limit settings as the defaults, then we don't
initialize bdi->io_pages. This means that file systems may need to
work around bdi->io_pages == 0, which is somewhat messy.
Initialize the default value just like we do for ->ra_pages.
Cc: stable@vger.kernel.org
Fixes: 9491ae4aad ("mm: don't cap request size based on read-ahead setting")
Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tascam FE-8 is known to support communication by asynchronous transaction
only. The support can be implemented in userspace application and
snd-firewire-ctl-services project has the support. However, ALSA
firewire-tascam driver is bound to the model.
This commit changes device entries so that the model is excluded. In a
commit 53b3ffee78 ("ALSA: firewire-tascam: change device probing
processing"), I addressed to the concern that version field in
configuration differs depending on installed firmware. However, as long
as I checked, the version number is fixed. It's safe to return version
number back to modalias.
Fixes: 53b3ffee78 ("ALSA: firewire-tascam: change device probing processing")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200823075537.56255-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit a092b7233f upstream.
The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17743798d8 upstream.
There is a race between the assignment of `table->data` and write value
to the pointer of `table->data` in the __do_proc_doulongvec_minmax() on
the other thread.
CPU0: CPU1:
proc_sys_write
hugetlb_sysctl_handler proc_sys_call_handler
hugetlb_sysctl_handler_common hugetlb_sysctl_handler
table->data = &tmp; hugetlb_sysctl_handler_common
table->data = &tmp;
proc_doulongvec_minmax
do_proc_doulongvec_minmax sysctl_head_finish
__do_proc_doulongvec_minmax unuse_table
i = table->data;
*i = val; // corrupt CPU1's stack
Fix this by duplicating the `table`, and only update the duplicate of
it. And introduce a helper of proc_hugetlb_doulongvec_minmax() to
simplify the code.
The following oops was seen:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor instruction fetch in kernel mode
#PF: error_code(0x0010) - not-present page
Code: Bad RIP value.
...
Call Trace:
? set_max_huge_pages+0x3da/0x4f0
? alloc_pool_huge_page+0x150/0x150
? proc_doulongvec_minmax+0x46/0x60
? hugetlb_sysctl_handler_common+0x1c7/0x200
? nr_hugepages_store+0x20/0x20
? copy_fd_bitmaps+0x170/0x170
? hugetlb_sysctl_handler+0x1e/0x20
? proc_sys_call_handler+0x2f1/0x300
? unregister_sysctl_table+0xb0/0xb0
? __fd_install+0x78/0x100
? proc_sys_write+0x14/0x20
? __vfs_write+0x4d/0x90
? vfs_write+0xef/0x240
? ksys_write+0xc0/0x160
? __ia32_sys_read+0x50/0x50
? __close_fd+0x129/0x150
? __x64_sys_write+0x43/0x50
? do_syscall_64+0x6c/0x200
? entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: e5ff215941 ("hugetlb: multiple hstates for multiple page sizes")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/20200828031146.43035-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13e45417ce upstream.
The usage of "capture group (...)" in the immediate condition after `&&`
results in `$1` being uninitialized. This issues a warning "Use of
uninitialized value $1 in regexp compilation at ./scripts/checkpatch.pl
line 2638".
I noticed this bug while running checkpatch on the set of commits from
v5.7 to v5.8-rc1 of the kernel on the commits with a diff content in
their commit message.
This bug was introduced in the script by commit e518e9a59e
("checkpatch: emit an error when there's a diff in a changelog"). It
has been in the script since then.
The author intended to store the match made by capture group in variable
`$1`. This should have contained the name of the file as `[\w/]+`
matched. However, this couldn't be accomplished due to usage of capture
group and `$1` in the same regular expression.
Fix this by placing the capture group in the condition before `&&`.
Thus, `$1` can be initialized to the text that capture group matches
thereby setting it to the desired and required value.
Fixes: e518e9a59e ("checkpatch: emit an error when there's a diff in a changelog")
Signed-off-by: Mrinal Pandey <mrinalmni@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Cc: Joe Perches <joe@perches.com>
Link: https://lkml.kernel.org/r/20200714032352.f476hanaj2dlmiot@mrinalpandey
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebfa440ce3 upstream.
SR-IOV VFs do not implement the memory enable bit of the command
register, therefore this bit is not set in config space after
pci_enable_device(). This leads to an unintended difference
between PF and VF in hand-off state to the user. We can correct
this by setting the initial value of the memory enable bit in our
virtualized config space. There's really no need however to
ever fault a user on a VF though as this would only indicate an
error in the user's management of the enable bit, versus a PF
where the same access could trigger hardware faults.
Fixes: abafbc551f ("vfio-pci: Invalidate mmaps and block MMIO access on disabled memory")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71a7f8cb1c upstream.
AT instructions do a translation table walk and return the result, or
the fault in PAR_EL1. KVM uses these to find the IPA when the value is
not provided by the CPU in HPFAR_EL1.
If a translation table walk causes an external abort it is taken as an
exception, even if it was due to an AT instruction. (DDI0487F.a's D5.2.11
"Synchronous faults generated by address translation instructions")
While we previously made KVM resilient to exceptions taken due to AT
instructions, the device access causes mismatched attributes, and may
occur speculatively. Prevent this, by forbidding a walk through memory
described as device at stage2. Now such AT instructions will report a
stage2 fault.
Such a fault will cause KVM to restart the guest. If the AT instructions
always walk the page tables, but guest execution uses the translation cached
in the TLB, the guest can't make forward progress until the TLB entry is
evicted. This isn't a problem, as since commit 5dcd0fdbb4 ("KVM: arm64:
Defer guest entry when an asynchronous exception is pending"), KVM will
return to the host to process IRQs allowing the rest of the system to keep
running.
Cc: stable@vger.kernel.org # v4.19
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88a84ccccb upstream.
KVM doesn't expect any synchronous exceptions when executing, any such
exception leads to a panic(). AT instructions access the guest page
tables, and can cause a synchronous external abort to be taken.
The arm-arm is unclear on what should happen if the guest has configured
the hardware update of the access-flag, and a memory type in TCR_EL1 that
does not support atomic operations. B2.2.6 "Possible implementation
restrictions on using atomic instructions" from DDI0487F.a lists
synchronous external abort as a possible behaviour of atomic instructions
that target memory that isn't writeback cacheable, but the page table
walker may behave differently.
Make KVM robust to synchronous exceptions caused by AT instructions.
Add a get_user() style helper for AT instructions that returns -EFAULT
if an exception was generated.
While KVM's version of the exception table mixes synchronous and
asynchronous exceptions, only one of these can occur at each location.
Re-enter the guest when the AT instructions take an exception on the
assumption the guest will take the same exception. This isn't guaranteed
to make forward progress, as the AT instructions may always walk the page
tables, but guest execution may use the translation cached in the TLB.
This isn't a problem, as since commit 5dcd0fdbb4 ("KVM: arm64: Defer guest
entry when an asynchronous exception is pending"), KVM will return to the
host to process IRQs allowing the rest of the system to keep running.
Cc: stable@vger.kernel.org # v4.19
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dcd0fdbb4 upstream.
SError that occur during world-switch's entry to the guest will be
accounted to the guest, as the exception is masked until we enter the
guest... but we want to attribute the SError as precisely as possible.
Reading DISR_EL1 before guest entry requires free registers, and using
ESB+DISR_EL1 to consume and read back the ESR would leave KVM holding
a host SError... We would rather leave the SError pending and let the
host take it once we exit world-switch. To do this, we need to defer
guest-entry if an SError is pending.
Read the ISR to see if SError (or an IRQ) is pending. If so fake an
exit. Place this check between __guest_enter()'s save of the host
registers, and restore of the guest's. SError that occur between
here and the eret into the guest must have affected the guest's
registers, which we can naturally attribute to the guest.
The dsb is needed to ensure any previous writes have been done before
we read ISR_EL1. On systems without the v8.2 RAS extensions this
doesn't give us anything as we can't contain errors, and the ESR bits
to describe the severity are all implementation-defined. Replace
this with a nop for these systems.
Cc: stable@vger.kernel.org # v4.19
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9ee186bb7 upstream.
KVM has a one instruction window where it will allow an SError exception
to be consumed by the hypervisor without treating it as a hypervisor bug.
This is used to consume asynchronous external abort that were caused by
the guest.
As we are about to add another location that survives unexpected exceptions,
generalise this code to make it behave like the host's extable.
KVM's version has to be mapped to EL2 to be accessible on nVHE systems.
The SError vaxorcism code is a one instruction window, so has two entries
in the extable. Because the KVM code is copied for VHE and nVHE, we end up
with four entries, half of which correspond with code that isn't mapped.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9e040efcc upstream.
The function dax_direct_access doesn't take partitions into account,
it always maps pages from the beginning of the device. Therefore,
persistent_memory_claim() must get the partition offset using
get_start_sect() and add it to the page offsets passed to
dax_direct_access().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 48debafe4f ("dm: add writecache target")
Cc: stable@vger.kernel.org # 4.18+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b5455636f upstream.
All three generations of Sandisk SSDs lock up hard intermittently.
Experiments showed that disabling NCQ lowered the failure rate significantly
and the kernel has been disabling NCQ for some models of SD7's and 8's,
which is obviously undesirable.
Karthik worked with Sandisk to root cause the hard lockups to trim commands
larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which
limits max trim size to 128M and applies it to all three generations of
Sandisk SSDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Karthik Shivaram <karthikgs@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a84a8d0d upstream.
The basic permission bits (protection bits in AmigaOS) have been broken
in Linux' AFFS - it would only set bits, but never delete them.
Also, contrary to the documentation, the Archived bit was not handled.
Let's fix this for good, and set the bits such that Linux and classic
AmigaOS can coexist in the most peaceful manner.
Also, update the documentation to represent the current state of things.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Max Staudt <max@enpas.org>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2e2d73fa2 upstream.
Device drivers do not expect to have change_protocol or wakeup
re-programming to be accesed after rc_unregister_device(). This can
cause the device driver to access deallocated resources.
Cc: <stable@vger.kernel.org> # 4.16+
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 858e0ad930 upstream.
When system is suspended with active audio playback to HDMI/DP, two
alternative sequences can happen at resume:
a) monitor is detected first and ALSA prepare follows normal
stream setup sequence, or
b) ALSA prepare is called first, but monitor is not yet detected,
so PCM is restarted without a pin,
In case of (b), on i915 systems, haswell_verify_D0() is not called at
resume and the pin power state may be incorrect. Result is lack of audio
after resume with no error reported back to user-space.
Fix the problem by always verifying converter and pin state in the
i915_pin_cvt_fixup().
BugLink: https://github.com/thesofproject/linux/issues/2388
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826170306.701566-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a48b73eca4 ]
With the conversion of the tree locks to rwsem I got the following
lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.8.0-rc7-00165-g04ec4da5f45f-dirty #922 Not tainted
------------------------------------------------------
compsize/11122 is trying to acquire lock:
ffff889fabca8768 (&mm->mmap_lock#2){++++}-{3:3}, at: __might_fault+0x3e/0x90
but task is already holding lock:
ffff889fe720fe40 (btrfs-fs-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (btrfs-fs-00){++++}-{3:3}:
down_write_nested+0x3b/0x70
__btrfs_tree_lock+0x24/0x120
btrfs_search_slot+0x756/0x990
btrfs_lookup_inode+0x3a/0xb4
__btrfs_update_delayed_inode+0x93/0x270
btrfs_async_run_delayed_root+0x168/0x230
btrfs_work_helper+0xd4/0x570
process_one_work+0x2ad/0x5f0
worker_thread+0x3a/0x3d0
kthread+0x133/0x150
ret_from_fork+0x1f/0x30
-> #1 (&delayed_node->mutex){+.+.}-{3:3}:
__mutex_lock+0x9f/0x930
btrfs_delayed_update_inode+0x50/0x440
btrfs_update_inode+0x8a/0xf0
btrfs_dirty_inode+0x5b/0xd0
touch_atime+0xa1/0xd0
btrfs_file_mmap+0x3f/0x60
mmap_region+0x3a4/0x640
do_mmap+0x376/0x580
vm_mmap_pgoff+0xd5/0x120
ksys_mmap_pgoff+0x193/0x230
do_syscall_64+0x50/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
-> #0 (&mm->mmap_lock#2){++++}-{3:3}:
__lock_acquire+0x1272/0x2310
lock_acquire+0x9e/0x360
__might_fault+0x68/0x90
_copy_to_user+0x1e/0x80
copy_to_sk.isra.32+0x121/0x300
search_ioctl+0x106/0x200
btrfs_ioctl_tree_search_v2+0x7b/0xf0
btrfs_ioctl+0x106f/0x30a0
ksys_ioctl+0x83/0xc0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x50/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
other info that might help us debug this:
Chain exists of:
&mm->mmap_lock#2 --> &delayed_node->mutex --> btrfs-fs-00
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(btrfs-fs-00);
lock(&delayed_node->mutex);
lock(btrfs-fs-00);
lock(&mm->mmap_lock#2);
*** DEADLOCK ***
1 lock held by compsize/11122:
#0: ffff889fe720fe40 (btrfs-fs-00){++++}-{3:3}, at: __btrfs_tree_read_lock+0x39/0x180
stack backtrace:
CPU: 17 PID: 11122 Comm: compsize Kdump: loaded Not tainted 5.8.0-rc7-00165-g04ec4da5f45f-dirty #922
Hardware name: Quanta Tioga Pass Single Side 01-0030993006/Tioga Pass Single Side, BIOS F08_3A18 12/20/2018
Call Trace:
dump_stack+0x78/0xa0
check_noncircular+0x165/0x180
__lock_acquire+0x1272/0x2310
lock_acquire+0x9e/0x360
? __might_fault+0x3e/0x90
? find_held_lock+0x72/0x90
__might_fault+0x68/0x90
? __might_fault+0x3e/0x90
_copy_to_user+0x1e/0x80
copy_to_sk.isra.32+0x121/0x300
? btrfs_search_forward+0x2a6/0x360
search_ioctl+0x106/0x200
btrfs_ioctl_tree_search_v2+0x7b/0xf0
btrfs_ioctl+0x106f/0x30a0
? __do_sys_newfstat+0x5a/0x70
? ksys_ioctl+0x83/0xc0
ksys_ioctl+0x83/0xc0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x50/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The problem is we're doing a copy_to_user() while holding tree locks,
which can deadlock if we have to do a page fault for the copy_to_user().
This exists even without my locking changes, so it needs to be fixed.
Rework the search ioctl to do the pre-fault and then
copy_to_user_nofault for the copying.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d1585ca0f ]
Commit 3d7081822f ("uaccess: Add non-pagefault user-space read functions")
missed to add probe write function, therefore factor out a probe_write_common()
helper with most logic of probe_kernel_write() except setting KERNEL_DS, and
add a new probe_user_write() helper so it can be used from BPF side.
Again, on some archs, the user address space and kernel address space can
co-exist and be overlapping, so in such case, setting KERNEL_DS would mean
that the given address is treated as being in kernel address space.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/bpf/9df2542e68141bfa3addde631441ee45503856a8.1572649915.git.daniel@iogearbox.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d7081822f ]
Add probe_user_read(), strncpy_from_unsafe_user() and
strnlen_unsafe_user() which allows caller to access user-space
in IRQ context.
Current probe_kernel_read() and strncpy_from_unsafe() are
not available for user-space memory, because it sets
KERNEL_DS while accessing data. On some arch, user address
space and kernel address space can be co-exist, but others
can not. In that case, setting KERNEL_DS means given
address is treated as a kernel address space.
Also strnlen_user() is only available from user context since
it can sleep if pagefault is enabled.
To access user-space memory without pagefault, we need
these new functions which sets USER_DS while accessing
the data.
Link: http://lkml.kernel.org/r/155789869802.26965.4940338412595759063.stgit@devnote2
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3beaa253f ]
These are special extent buffers that get rewound in order to lookup
the state of the tree at a specific point in time. As such they do not
go through the normal initialization paths that set their lockdep class,
so handle them appropriately when they are created and before they are
locked.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
