[ Upstream commit 9feb0763e4 ]
Cleanup accelerometer device handling:
-Drop acer_wmi_accel_destroy instead directly call input_unregister_device.
-The information tracked by the CAP_ACCEL flag mirrors acer_wmi_accel_dev
being NULL. Drop the CAP flag, this is a preparation change for allowing
users to override the capability flags. Dropping the flag stops users
from causing a NULL pointer dereference by forcing the capability.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201019185628.264473-3-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfeeea60af ]
We need to enable no-reset-on-init quirk for GPMC if the config
option for CONFIG_OMAP_GPMC_DEBUG is set. Otherwise the GPMC
driver code is unable to show the bootloader configured timings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4add4d988f ]
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 547801380e ]
WCN3991 supports connectable advertisements so we need to add the valid
le states quirk so the 'central-peripheral' role is exposed in
userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4d14c5cde5 upstream
Calling btrfs_qgroup_reserve_meta_prealloc from
btrfs_delayed_inode_reserve_metadata can result in flushing delalloc
while holding a transaction and delayed node locks. This is deadlock
prone. In the past multiple commits:
* ae5e070eac ("btrfs: qgroup: don't try to wait flushing if we're
already holding a transaction")
* 6f23277a49 ("btrfs: qgroup: don't commit transaction when we already
hold the handle")
Tried to solve various aspects of this but this was always a
whack-a-mole game. Unfortunately those 2 fixes don't solve a deadlock
scenario involving btrfs_delayed_node::mutex. Namely, one thread
can call btrfs_dirty_inode as a result of reading a file and modifying
its atime:
PID: 6963 TASK: ffff8c7f3f94c000 CPU: 2 COMMAND: "test"
#0 __schedule at ffffffffa529e07d
#1 schedule at ffffffffa529e4ff
#2 schedule_timeout at ffffffffa52a1bdd
#3 wait_for_completion at ffffffffa529eeea <-- sleeps with delayed node mutex held
#4 start_delalloc_inodes at ffffffffc0380db5
#5 btrfs_start_delalloc_snapshot at ffffffffc0393836
#6 try_flush_qgroup at ffffffffc03f04b2
#7 __btrfs_qgroup_reserve_meta at ffffffffc03f5bb6 <-- tries to reserve space and starts delalloc inodes.
#8 btrfs_delayed_update_inode at ffffffffc03e31aa <-- acquires delayed node mutex
#9 btrfs_update_inode at ffffffffc0385ba8
#10 btrfs_dirty_inode at ffffffffc038627b <-- TRANSACTIION OPENED
#11 touch_atime at ffffffffa4cf0000
#12 generic_file_read_iter at ffffffffa4c1f123
#13 new_sync_read at ffffffffa4ccdc8a
#14 vfs_read at ffffffffa4cd0849
#15 ksys_read at ffffffffa4cd0bd1
#16 do_syscall_64 at ffffffffa4a052eb
#17 entry_SYSCALL_64_after_hwframe at ffffffffa540008c
This will cause an asynchronous work to flush the delalloc inodes to
happen which can try to acquire the same delayed_node mutex:
PID: 455 TASK: ffff8c8085fa4000 CPU: 5 COMMAND: "kworker/u16:30"
#0 __schedule at ffffffffa529e07d
#1 schedule at ffffffffa529e4ff
#2 schedule_preempt_disabled at ffffffffa529e80a
#3 __mutex_lock at ffffffffa529fdcb <-- goes to sleep, never wakes up.
#4 btrfs_delayed_update_inode at ffffffffc03e3143 <-- tries to acquire the mutex
#5 btrfs_update_inode at ffffffffc0385ba8 <-- this is the same inode that pid 6963 is holding
#6 cow_file_range_inline.constprop.78 at ffffffffc0386be7
#7 cow_file_range at ffffffffc03879c1
#8 btrfs_run_delalloc_range at ffffffffc038894c
#9 writepage_delalloc at ffffffffc03a3c8f
#10 __extent_writepage at ffffffffc03a4c01
#11 extent_write_cache_pages at ffffffffc03a500b
#12 extent_writepages at ffffffffc03a6de2
#13 do_writepages at ffffffffa4c277eb
#14 __filemap_fdatawrite_range at ffffffffa4c1e5bb
#15 btrfs_run_delalloc_work at ffffffffc0380987 <-- starts running delayed nodes
#16 normal_work_helper at ffffffffc03b706c
#17 process_one_work at ffffffffa4aba4e4
#18 worker_thread at ffffffffa4aba6fd
#19 kthread at ffffffffa4ac0a3d
#20 ret_from_fork at ffffffffa54001ff
To fully address those cases the complete fix is to never issue any
flushing while holding the transaction or the delayed node lock. This
patch achieves it by calling qgroup_reserve_meta directly which will
either succeed without flushing or will fail and return -EDQUOT. In the
latter case that return value is going to be propagated to
btrfs_dirty_inode which will fallback to start a new transaction. That's
fine as the majority of time we expect the inode will have
BTRFS_DELAYED_NODE_INODE_DIRTY flag set which will result in directly
copying the in-memory state.
Fixes: c53e965360 ("btrfs: qgroup: try to flush qgroup space when we get -EDQUOT")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 778e45d772 upstream
The kernel test robot reported multiple linkage problems like this:
hppa64-linux-ld: init/main.o(.init.text+0x56c): cannot reach printk
init/main.o: in function `unknown_bootoption':
(.init.text+0x56c): relocation truncated to fit: R_PARISC_PCREL22F against
symbol `printk' defined in .text.unlikely section in kernel/printk/printk.o
There are two ways to solve it:
a) Enable the -mlong-call compiler option (CONFIG_MLONGCALLS),
b) Add long branch stub support in 64-bit linker.
While b) is the long-term solution, this patch works around the issue by
automatically enabling the CONFIG_MLONGCALLS option when
CONFIG_COMPILE_TEST is set, which indicates that a non-production kernel
(e.g. 0-day kernel) is built.
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 00e35f2b0e ("parisc: Enable -mlong-calls gcc option by default when !CONFIG_MODULES")
Cc: stable@vger.kernel.org # v5.6+
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc22c1c058 upstream
My 2TB SKC2000 showed the exact same symptoms that were provided
in 538e4a8c57 ("nvme-pci: avoid the deepest sleep state on
Kingston A2000 SSDs"), i.e. a complete NVME lockup that needed
cold boot to get it back.
According to some sources, the A2000 is simply a rebadged
SKC2000 with a slightly optimized firmware.
Adding the SKC2000 PCI ID to the quirk list with the same workaround
as the A2000 made my laptop survive a 5 hours long Yocto bootstrap
buildfest which reliably triggered the SSD lockup previously.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c27f3d011b upstream.
ACPICA commit c9e0116952363b0fa815143dca7e9a2eb4fefa61
The handling of the generic_serial_bus (I2C) and GPIO op_regions in
acpi_ev_address_space_dispatch() passes a number of extra parameters
to the address-space handler through the address-space Context pointer
(instead of using more function parameters).
The Context is shared between threads, so if multiple threads try to
call the handler for the same address-space at the same time, then
a second thread could change the parameters of a first thread while
the handler is running for the first thread.
An example of this race hitting is the Lenovo Yoga Tablet2 1015L,
where there are both attrib_bytes accesses and attrib_byte accesses
to the same address-space. The attrib_bytes access stores the number
of bytes to transfer in Context->access_length. Where as for the
attrib_byte access the number of bytes to transfer is always 1 and
field_obj->Field.access_length is unused (so 0). Both types of
accesses racing from different threads leads to the following problem:
1. Thread a. starts an attrib_bytes access, stores a non 0 value
from field_obj->Field.access_length in Context->access_length
2. Thread b. starts an attrib_byte access, stores 0 in
Context->access_length
3. Thread a. calls i2c_acpi_space_handler() (under Linux). Which
sees that the access-type is ACPI_GSB_ACCESS_ATTRIB_MULTIBYTE
and calls acpi_gsb_i2c_read_bytes(..., Context->access_length)
4. At this point Context->access_length is 0 (set by thread b.)
rather then the field_obj->Field.access_length value from thread a.
This 0 length reads leads to the following errors being logged:
i2c i2c-0: adapter quirk: no zero length (addr 0x0078, size 0, read)
i2c i2c-0: i2c read 0 bytes from client@0x78 starting at reg 0x0 failed, error: -95
Note this is just an example of the problems which this race can cause.
There are likely many more (sporadic) problems caused by this race.
This commit adds a new context_mutex to struct acpi_object_addr_handler
and makes acpi_ev_address_space_dispatch() take that mutex when
using the shared Context to pass extra parameters to an address-space
handler, fixing this race.
Note the new mutex must be taken *after* exiting the interpreter,
therefor the existing acpi_ex_exit_interpreter() call is moved to above
the code which stores the extra parameters in the Context.
Link: https://github.com/acpica/acpica/commit/c9e01169
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2a0437081 upstream.
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c83465f32 upstream.
Commit db68ce10c4 ("new helper: uaccess_kernel()") replaced
segment_eq(get_fs(), KERNEL_DS) with uaccess_kernel(). But the correct
method for tomoyo to check whether current is a kernel thread in order
to assume that kernel threads are privileged for socket operations was
(current->flags & PF_KTHREAD). Now that uaccess_kernel() became 0 on x86,
tomoyo has to fix this problem. Do like commit 942cb357ae ("Smack:
Handle io_uring kernel thread privileges") does.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aed5041ef9 upstream.
of_dma_get_max_cpu_address() is not defined if !CONFIG_OF_ADDRESS, so
return early in of_unittest_dma_get_max_cpu_address().
Fixes: 07d13a1d61 ("of: unittest: Add test for of_dma_get_max_cpu_address()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 444d66a23c ]
As per Intel vt-d spec, Rev 3.0 (section 10.4.45 "Virtual Command Response
Register"), the status code of "No PASID available" error in response to
the Allocate PASID command is 2, not 1. The same for "Invalid PASID" error
in response to the Free PASID command.
We will otherwise see confusing kernel log under the command failure from
guest side. Fix it.
Fixes: 24f27d32ab ("iommu/vt-d: Enlightened PASID allocation")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210227073909.432-1-yuzenghui@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77516d25f5 ]
The copy_to_user() function returns the number of bytes remaining but
we want to return -EFAULT to the user if it can't complete the copy.
The "st" variable only holds zero on success or negative error codes on
failure so the type should be int.
Fixes: 36f988e978 ("rsxx: Adding in debugfs entries.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 999340d511 ]
On little endian system, Use aarch64_be(gcc v7.3) downloaded from
linaro.org to build image with CONFIG_CPU_BIG_ENDIAN = y,
CONFIG_FTRACE = y, CONFIG_DYNAMIC_FTRACE = y.
gcc will create symbols of _mcount but recordmcount can not create
mcount_loc for *.o.
aarch64_be-linux-gnu-objdump -r fs/namei.o | grep mcount
00000000000000d0 R_AARCH64_CALL26 _mcount
...
0000000000007190 R_AARCH64_CALL26 _mcount
The reason is than funciton arm64_is_fake_mcount can not work correctly.
A symbol of _mcount in *.o compiled with big endian compiler likes:
00 00 00 2d 00 00 01 1b
w(rp->r_info) will return 0x2d instead of 0x011b. Because w() takes
uint32_t as parameter, which truncates rp->r_info.
Use w8() instead w() to read relp->r_info
Link: https://lkml.kernel.org/r/20210222135840.56250-1-chenjun102@huawei.com
Fixes: ea0eada456 ("recordmcount: only record relocation of type R_AARCH64_CALL26 on arm64.")
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a864e8f159 ]
Multiple bug reports report issues with the SOF and SST drivers when
dealing with single microphone cases.
We currently read the DMIC array information unconditionally but we
don't check that the configuration type is actually a mic array.
When the DMIC link does not rely on a mic array configuration, the
recommendation is to check the format information to infer the maximum
number of channels, and map this to the number of microphones.
This leaves a potential for a mismatch between actual microphones
available in hardware and what the ACPI table contains, but we have no
other source of information.
Note that single microphone configurations can alternatively be
handled with a 'mic array' configuration along with a 'vendor-defined'
geometry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201251
BugLink: https://github.com/thesofproject/linux/issues/2725
Fixes: 7a33ea70e1 ('ALSA: hda: intel-nhlt: handle NHLT VENDOR_DEFINED DMIC geometry')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210302000146.1177770-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 475f23b8c6 ]
When RDMA_RXE is enabled and CRYPTO is disabled, Kbuild gives the
following warning:
WARNING: unmet direct dependencies detected for CRYPTO_CRC32
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- RDMA_RXE [=y] && (INFINIBAND_USER_ACCESS [=y] || !INFINIBAND_USER_ACCESS [=y]) && INET [=y] && PCI [=y] && INFINIBAND [=y] && INFINIBAND_VIRT_DMA [=y]
This is because RDMA_RXE selects CRYPTO_CRC32, without depending on or
selecting CRYPTO, despite that config option being subordinate to CRYPTO.
Fixes: cee2688e3c ("IB/rxe: Offload CRC calculation when possible")
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://lore.kernel.org/r/21525878.NYvzQUHefP@ubuntu-mate-laptop
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26a9630c72 ]
Currently the mask operation on variable conf is just 3 bits so
the switch statement case value of 8 is unreachable dead code.
The function daio_mgr_dao_init can be passed a 4 bit value,
function dao_rsc_init calls it with conf set to:
conf = (desc->msr & 0x7) | (desc->passthru << 3);
so clearly when desc->passthru is set to 1 then conf can be
at least 8.
Fix this by changing the mask to 0xf.
Fixes: 8cc7236148 ("ALSA: SB X-Fi driver merge")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210227001527.1077484-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2b8652936f upstream
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
Instructing the DMA layer about these limitations is straight-forward,
even though we had to fix some issues regarding memory limits set in
the IORT for named components, and regarding the handling of ACPI _DMA
methods. However, the DMA layer also needs to be able to allocate
memory that is guaranteed to meet those DMA constraints, for bounce
buffering as well as allocating the backing for consistent mappings.
This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately,
it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes
problems with kdump, and potentially in other places where allocations
cannot cross zone boundaries. Therefore, we should avoid having two
separate DMA zones when possible.
So let's do an early scan of the IORT, and only create the ZONE_DMA
if we encounter any devices that need it. This puts the burden on
the firmware to describe such limitations in the IORT, which may be
redundant (and less precise) if _DMA methods are also being provided.
However, it should be noted that this situation is highly unusual for
arm64 ACPI machines. Also, the DMA subsystem still gives precedence to
the _DMA method if implemented, and so we will not lose the ability to
perform streaming DMA outside the ZONE_DMA if the _DMA method permits
it.
[nsaenz: unified implementation with DT's counterpart]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20201119175400.9995-7-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8424ecdde7 upstream
We recently introduced a 1 GB sized ZONE_DMA to cater for platforms
incorporating masters that can address less than 32 bits of DMA, in
particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has
peripherals that can only address up to 1 GB (and its PCIe host
bridge can only access the bottom 3 GB)
The DMA layer also needs to be able to allocate memory that is
guaranteed to meet those DMA constraints, for bounce buffering as well
as allocating the backing for consistent mappings. This is why the 1 GB
ZONE_DMA was introduced recently. Unfortunately, it turns out the having
a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes problems with kdump, and
potentially in other places where allocations cannot cross zone
boundaries. Therefore, we should avoid having two separate DMA zones
when possible.
So, with the help of of_dma_get_max_cpu_address() get the topmost
physical address accessible to all DMA masters in system and use that
information to fine-tune ZONE_DMA's size. In the absence of addressing
limited masters ZONE_DMA will span the whole 32-bit address space,
otherwise, in the case of the Raspberry Pi 4 it'll only span the 30-bit
address space, and have ZONE_DMA32 cover the rest of the 32-bit address
space.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20201119175400.9995-6-nsaenzjulienne@suse.de
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660d206219 upstream.
Unlike many other structure types defined in the crypto API, the
'shash_desc' structure is permitted to live on the stack, which
implies its contents may not be accessed by DMA masters. (This is
due to the fact that the stack may be located in the vmalloc area,
which requires a different virtual-to-physical translation than the
one implemented by the DMA subsystem)
Our definition of CRYPTO_MINALIGN_ATTR is based on ARCH_KMALLOC_MINALIGN,
which may take DMA constraints into account on architectures that support
non-cache coherent DMA such as ARM and arm64. In this case, the value is
chosen to reflect the largest cacheline size in the system, in order to
ensure that explicit cache maintenance as required by non-coherent DMA
masters does not affect adjacent, unrelated slab allocations. On arm64,
this value is currently set at 128 bytes.
This means that applying CRYPTO_MINALIGN_ATTR to struct shash_desc is both
unnecessary (as it is never used for DMA), and undesirable, given that it
wastes stack space (on arm64, performing the alignment costs 112 bytes in
the worst case, and the hole between the 'tfm' and '__ctx' members takes
up another 120 bytes, resulting in an increased stack footprint of up to
232 bytes.) So instead, let's switch to the minimum SLAB alignment, which
does not take DMA constraints into account.
Note that this is a no-op for x86.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df7b59ba92 upstream.
Optional Forward Error Correction (FEC) code in dm-verity uses
Reed-Solomon code and should support roots from 2 to 24.
The error correction parity bytes (of roots lengths per RS block) are
stored on a separate device in sequence without any padding.
Currently, to access FEC device, the dm-verity-fec code uses dm-bufio
client with block size set to verity data block (usually 4096 or 512
bytes).
Because this block size is not divisible by some (most!) of the roots
supported lengths, data repair cannot work for partially stored parity
bytes.
This fix changes FEC device dm-bufio block size to "roots << SECTOR_SHIFT"
where we can be sure that the full parity data is always available.
(There cannot be partial FEC blocks because parity must cover whole
sectors.)
Because the optional FEC starting offset could be unaligned to this
new block size, we have to use dm_bufio_set_sector_offset() to
configure it.
The problem is easily reproduced using veritysetup, e.g. for roots=13:
# create verity device with RS FEC
dd if=/dev/urandom of=data.img bs=4096 count=8 status=none
veritysetup format data.img hash.img --fec-device=fec.img --fec-roots=13 | awk '/^Root hash/{ print $3 }' >roothash
# create an erasure that should be always repairable with this roots setting
dd if=/dev/zero of=data.img conv=notrunc bs=1 count=8 seek=4088 status=none
# try to read it through dm-verity
veritysetup open data.img test hash.img --fec-device=fec.img --fec-roots=13 $(cat roothash)
dd if=/dev/mapper/test of=/dev/null bs=4096 status=noxfer
# wait for possible recursive recovery in kernel
udevadm settle
veritysetup close test
With this fix, errors are properly repaired.
device-mapper: verity-fec: 7:1: FEC 0: corrected 8 errors
...
Without it, FEC code usually ends on unrecoverable failure in RS decoder:
device-mapper: verity-fec: 7:1: FEC 0: failed to correct: -74
...
This problem is present in all kernels since the FEC code's
introduction (kernel 4.5).
It is thought that this problem is not visible in Android ecosystem
because it always uses a default RS roots=2.
Depends-on: a14e5ec66a ("dm bufio: subtract the number of initial sectors in dm_bufio_get_device_size")
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Tested-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a14e5ec66a upstream.
dm_bufio_get_device_size returns the device size in blocks. Before
returning the value, we must subtract the nubmer of starting
sectors. The number of starting sectors may not be divisible by block
size.
Note that currently, no target is using dm_bufio_set_sector_offset and
dm_bufio_get_device_size simultaneously, so this change has no effect.
However, an upcoming dm-verity-fec fix needs this change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f6be606e7 upstream.
Part of the logic of the new time stamp code depends on the before_stamp and
the write_stamp to be different if the write_stamp does not match the last
event on the buffer, as it will be used to calculate the delta of the next
event written on the buffer.
The discard logic depends on this, as the next event to come in needs to
inject a full timestamp as it can not rely on the last event timestamp in
the buffer because it is unknown due to events after it being discarded. But
by changing the write_stamp back to the time before it, it forces the next
event to use a full time stamp, instead of relying on it.
The issue came when a full time stamp was used for the event, and
rb_time_delta() returns zero in that case. The update to the write_stamp
(which subtracts delta) made it not change. Then when the event is removed
from the buffer, because the before_stamp and write_stamp still match, the
next event written would calculate its delta from the write_stamp, but that
would be wrong as the write_stamp is of the time of the event that was
discarded.
In the case that the delta change being made to write_stamp is zero, set the
before_stamp to zero as well, and this will force the next event to inject a
full timestamp and not use the current write_stamp.
Cc: stable@vger.kernel.org
Fixes: a389d86f7f ("ring-buffer: Have nested events still record running time stamp")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd57a98d6f upstream.
When we have smack enabled, during the creation of a directory smack may
attempt to add a "smack transmute" xattr on the inode, which results in
the following warning and trace:
WARNING: CPU: 3 PID: 2548 at fs/btrfs/transaction.c:537 start_transaction+0x489/0x4f0
Modules linked in: nft_objref nf_conntrack_netbios_ns (...)
CPU: 3 PID: 2548 Comm: mkdir Not tainted 5.9.0-rc2smack+ #81
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
RIP: 0010:start_transaction+0x489/0x4f0
Code: e9 be fc ff ff (...)
RSP: 0018:ffffc90001887d10 EFLAGS: 00010202
RAX: ffff88816f1e0000 RBX: 0000000000000201 RCX: 0000000000000003
RDX: 0000000000000201 RSI: 0000000000000002 RDI: ffff888177849000
RBP: ffff888177849000 R08: 0000000000000001 R09: 0000000000000004
R10: ffffffff825e8f7a R11: 0000000000000003 R12: ffffffffffffffe2
R13: 0000000000000000 R14: ffff88803d884270 R15: ffff8881680d8000
FS: 00007f67317b8440(0000) GS:ffff88817bcc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f67247a22a8 CR3: 000000004bfbc002 CR4: 0000000000370ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? slab_free_freelist_hook+0xea/0x1b0
? trace_hardirqs_on+0x1c/0xe0
btrfs_setxattr_trans+0x3c/0xf0
__vfs_setxattr+0x63/0x80
smack_d_instantiate+0x2d3/0x360
security_d_instantiate+0x29/0x40
d_instantiate_new+0x38/0x90
btrfs_mkdir+0x1cf/0x1e0
vfs_mkdir+0x14f/0x200
do_mkdirat+0x6d/0x110
do_syscall_64+0x2d/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f673196ae6b
Code: 8b 05 11 (...)
RSP: 002b:00007ffc3c679b18 EFLAGS: 00000246 ORIG_RAX: 0000000000000053
RAX: ffffffffffffffda RBX: 00000000000001ff RCX: 00007f673196ae6b
RDX: 0000000000000000 RSI: 00000000000001ff RDI: 00007ffc3c67a30d
RBP: 00007ffc3c67a30d R08: 00000000000001ff R09: 0000000000000000
R10: 000055d3e39fe930 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffc3c679cd8 R14: 00007ffc3c67a30d R15: 00007ffc3c679ce0
irq event stamp: 11029
hardirqs last enabled at (11037): [<ffffffff81153fe6>] console_unlock+0x486/0x670
hardirqs last disabled at (11044): [<ffffffff81153c01>] console_unlock+0xa1/0x670
softirqs last enabled at (8864): [<ffffffff81e0102f>] asm_call_on_stack+0xf/0x20
softirqs last disabled at (8851): [<ffffffff81e0102f>] asm_call_on_stack+0xf/0x20
This happens because at btrfs_mkdir() we call d_instantiate_new() while
holding a transaction handle, which results in the following call chain:
btrfs_mkdir()
trans = btrfs_start_transaction(root, 5);
d_instantiate_new()
smack_d_instantiate()
__vfs_setxattr()
btrfs_setxattr_trans()
btrfs_start_transaction()
start_transaction()
WARN_ON()
--> a tansaction start has TRANS_EXTWRITERS
set in its type
h->orig_rsv = h->block_rsv
h->block_rsv = NULL
btrfs_end_transaction(trans)
Besides the warning triggered at start_transaction, we set the handle's
block_rsv to NULL which may cause some surprises later on.
So fix this by making btrfs_setxattr_trans() not start a transaction when
we already have a handle on one, stored in current->journal_info, and use
that handle. We are good to use the handle because at btrfs_mkdir() we did
reserve space for the xattr and the inode item.
Reported-by: Casey Schaufler <casey@schaufler-ca.com>
CC: stable@vger.kernel.org # 5.4+
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Link: https://lore.kernel.org/linux-btrfs/434d856f-bd7b-4889-a6ec-e81aaebfa735@schaufler-ca.com/
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f6a49de64 upstream.
If btrfs_qgroup_reserve_data returns an error (i.e quota limit reached)
the handling logic directly goes to the 'out' label without first
unlocking the extent range between lockstart, lockend. This results in
deadlocks as other processes try to lock the same extent.
Fixes: a7f8b1c2ac ("btrfs: file: reserve qgroup space after the hole punch range is locked")
CC: stable@vger.kernel.org # 5.10+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f9c03d824 upstream.
Following commit f218ea6c47 ("btrfs: delayed-inode: Remove wrong
qgroup meta reservation calls") this function now reserves num_bytes,
rather than the fixed amount of nodesize. As such this requires the
same amount to be freed in case of failure. Fix this by adjusting
the amount we are freeing.
Fixes: f218ea6c47 ("btrfs: delayed-inode: Remove wrong qgroup meta reservation calls")
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5011c5a663 upstream.
The problem is we're copying "inherit" from user space but we don't
necessarily know that we're copying enough data for a 64 byte
struct. Then the next problem is that 'inherit' has a variable size
array at the end, and we have to verify that array is the size we
expected.
Fixes: 6f72c7e20d ("Btrfs: add qgroup inheritance")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c17916510 upstream.
During allocation the allocator will try to allocate an extent using
cluster policy. Once the current cluster is exhausted it will remove the
entry under btrfs_free_cluster::lock and subsequently acquire
btrfs_free_space_ctl::tree_lock to dispose of the already-deleted entry
and adjust btrfs_free_space_ctl::total_bitmap. This poses a problem
because there exists a race condition between removing the entry under
one lock and doing the necessary accounting holding a different lock
since extent freeing only uses the 2nd lock. This can result in the
following situation:
T1: T2:
btrfs_alloc_from_cluster insert_into_bitmap <holds tree_lock>
if (entry->bytes == 0) if (block_group && !list_empty(&block_group->cluster_list)) {
rb_erase(entry)
spin_unlock(&cluster->lock);
(total_bitmaps is still 4) spin_lock(&cluster->lock);
<doesn't find entry in cluster->root>
spin_lock(&ctl->tree_lock); <goes to new_bitmap label, adds
<blocked since T2 holds tree_lock> <a new entry and calls add_new_bitmap>
recalculate_thresholds <crashes,
due to total_bitmaps
becoming 5 and triggering
an ASSERT>
To fix this ensure that once depleted, the cluster entry is deleted when
both cluster lock and tree locks are held in the allocator (T1), this
ensures that even if there is a race with a concurrent
insert_into_bitmap call it will correctly find the entry in the cluster
and add the new space to it.
CC: <stable@vger.kernel.org> # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3660d0bcdb upstream.
When using the NO_HOLES feature, if we clone a file range that spans only
a hole into a range that is at or beyond the current i_size of the
destination file, we end up not setting the full sync runtime flag on the
inode. As a result, if we then fsync the destination file and have a power
failure, after log replay we can end up exposing stale data instead of
having a hole for that range.
The conditions for this to happen are the following:
1) We have a file with a size of, for example, 1280K;
2) There is a written (non-prealloc) extent for the file range from 1024K
to 1280K with a length of 256K;
3) This particular file extent layout is durably persisted, so that the
existing superblock persisted on disk points to a subvolume root where
the file has that exact file extent layout and state;
4) The file is truncated to a smaller size, to an offset lower than the
start offset of its last extent, for example to 800K. The truncate sets
the full sync runtime flag on the inode;
6) Fsync the file to log it and clear the full sync runtime flag;
7) Clone a region that covers only a hole (implicit hole due to NO_HOLES)
into the file with a destination offset that starts at or beyond the
256K file extent item we had - for example to offset 1024K;
8) Since the clone operation does not find extents in the source range,
we end up in the if branch at the bottom of btrfs_clone() where we
punch a hole for the file range starting at offset 1024K by calling
btrfs_replace_file_extents(). There we end up not setting the full
sync flag on the inode, because we don't know we are being called in
a clone context (and not fallocate's punch hole operation), and
neither do we create an extent map to represent a hole because the
requested range is beyond eof;
9) A further fsync to the file will be a fast fsync, since the clone
operation did not set the full sync flag, and therefore it relies on
modified extent maps to correctly log the file layout. But since
it does not find any extent map marking the range from 1024K (the
previous eof) to the new eof, it does not log a file extent item
for that range representing the hole;
10) After a power failure no hole for the range starting at 1024K is
punched and we end up exposing stale data from the old 256K extent.
Turning this into exact steps:
$ mkfs.btrfs -f -O no-holes /dev/sdi
$ mount /dev/sdi /mnt
# Create our test file with 3 extents of 256K and a 256K hole at offset
# 256K. The file has a size of 1280K.
$ xfs_io -f -s \
-c "pwrite -S 0xab -b 256K 0 256K" \
-c "pwrite -S 0xcd -b 256K 512K 256K" \
-c "pwrite -S 0xef -b 256K 768K 256K" \
-c "pwrite -S 0x73 -b 256K 1024K 256K" \
/mnt/sdi/foobar
# Make sure it's durably persisted. We want the last committed super
# block to point to this particular file extent layout.
sync
# Now truncate our file to a smaller size, falling within a position of
# the second extent. This sets the full sync runtime flag on the inode.
# Then fsync the file to log it and clear the full sync flag from the
# inode. The third extent is no longer part of the file and therefore
# it is not logged.
$ xfs_io -c "truncate 800K" -c "fsync" /mnt/foobar
# Now do a clone operation that only clones the hole and sets back the
# file size to match the size it had before the truncate operation
# (1280K).
$ xfs_io \
-c "reflink /mnt/foobar 256K 1024K 256K" \
-c "fsync" \
/mnt/foobar
# File data before power failure:
$ od -A d -t x1 /mnt/foobar
0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
*
0262144 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
0524288 cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd
*
0786432 ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef
*
0819200 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
1310720
<power fail>
# Mount the fs again to replay the log tree.
$ mount /dev/sdi /mnt
# File data after power failure:
$ od -A d -t x1 /mnt/foobar
0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
*
0262144 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
0524288 cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd
*
0786432 ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef
*
0819200 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
1048576 73 73 73 73 73 73 73 73 73 73 73 73 73 73 73 73
*
1310720
The range from 1024K to 1280K should correspond to a hole but instead it
points to stale data, to the 256K extent that should not exist after the
truncate operation.
The issue does not exists when not using NO_HOLES, because for that case
we use file extent items to represent holes, these are found and copied
during the loop that iterates over extents at btrfs_clone(), and that
causes btrfs_replace_file_extents() to be called with a non-NULL
extent_info argument and therefore set the full sync runtime flag on the
inode.
So fix this by making the code that deals with a trailing hole during
cloning, at btrfs_clone(), to set the full sync flag on the inode, if the
range starts at or beyond the current i_size.
A test case for fstests will follow soon.
Backporting notes: for kernel 5.4 the change goes to ioctl.c into
btrfs_clone before the last call to btrfs_punch_hole_range.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd0734f2a8 upstream.
When creating a snapshot we check if the current number of swap files, in
the root, is non-zero, and if it is, we error out and warn that we can not
create the snapshot because there are active swap files.
However this is racy because when a task started activation of a swap
file, another task might have started already snapshot creation and might
have seen the counter for the number of swap files as zero. This means
that after the swap file is activated we may end up with a snapshot of the
same root successfully created, and therefore when the first write to the
swap file happens it has to fall back into COW mode, which should never
happen for active swap files.
Basically what can happen is:
1) Task A starts snapshot creation and enters ioctl.c:create_snapshot().
There it sees that root->nr_swapfiles has a value of 0 so it continues;
2) Task B enters btrfs_swap_activate(). It is not aware that another task
started snapshot creation but it did not finish yet. It increments
root->nr_swapfiles from 0 to 1;
3) Task B checks that the file meets all requirements to be an active
swap file - it has NOCOW set, there are no snapshots for the inode's
root at the moment, no file holes, no reflinked extents, etc;
4) Task B returns success and now the file is an active swap file;
5) Task A commits the transaction to create the snapshot and finishes.
The swap file's extents are now shared between the original root and
the snapshot;
6) A write into an extent of the swap file is attempted - there is a
snapshot of the file's root, so we fall back to COW mode and therefore
the physical location of the extent changes on disk.
So fix this by taking the snapshot lock during swap file activation before
locking the extent range, as that is the order in which we lock these
during buffered writes.
Fixes: ed46ff3d42 ("Btrfs: support swap files")
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 195a49eaf6 upstream.
When we active a swap file, at btrfs_swap_activate(), we acquire the
exclusive operation lock to prevent the physical location of the swap
file extents to be changed by operations such as balance and device
replace/resize/remove. We also call there can_nocow_extent() which,
among other things, checks if the block group of a swap file extent is
currently RO, and if it is we can not use the extent, since a write
into it would result in COWing the extent.
However we have no protection against a scrub operation running after we
activate the swap file, which can result in the swap file extents to be
COWed while the scrub is running and operating on the respective block
group, because scrub turns a block group into RO before it processes it
and then back again to RW mode after processing it. That means an attempt
to write into a swap file extent while scrub is processing the respective
block group, will result in COWing the extent, changing its physical
location on disk.
Fix this by making sure that block groups that have extents that are used
by active swap files can not be turned into RO mode, therefore making it
not possible for a scrub to turn them into RO mode. When a scrub finds a
block group that can not be turned to RO due to the existence of extents
used by swap files, it proceeds to the next block group and logs a warning
message that mentions the block group was skipped due to active swap
files - this is the same approach we currently use for balance.
Fixes: ed46ff3d42 ("Btrfs: support swap files")
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
