[ Upstream commit 504e417582 ]
This is required as part of the initialization sequence on certain SoCs.
If these registers are not initialized, the hardware can be unresponsive.
This fixes the driver on apq8060 (HP TouchPad device).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0aff01e7a ]
Because BD9571MWV_DVFS_MONIVDAC is not defined in the volatile table,
the physical register value is not updated by regmap and DVFS doesn't
work as expected. Fix it!
Fixes: d3ea212720 ("mfd: Add ROHM BD9571MWV-M MFD PMIC driver")
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[wsa: rebase, add 'Fixes', reword commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10628e3ecf ]
This function is supposed to return zero on success or negative error
codes on error. Unfortunately, there is a bug so it sometimes returns
non-zero, positive numbers on success.
I noticed this bug during review and I can't test it. It does appear
that the return is sometimes propogated back to _regmap_read() where all
non-zero returns are treated as failure so this may affect run time.
Fixes: 47c1697508 ("mfd: Align ab8500 with the abx500 interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a177276aa0 ]
If the PMIC ID is unknown, the current code would call
irq_domain_remove and panic, as pmic->irq_domain is only
initialized by mt6397_irq_init.
Return immediately with an error, if the chip ID is unsupported.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3888f62fe ]
When building the kernel with Clang, the following section mismatch
warnings appear:
WARNING: vmlinux.o(.text+0x7239cc): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:init_prcm_registers()
The function db8500_prcmu_probe() references
the function __init init_prcm_registers().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of init_prcm_registers is wrong.
WARNING: vmlinux.o(.text+0x723e28): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:fw_project_name()
The function db8500_prcmu_probe() references
the function __init fw_project_name().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of fw_project_name is wrong.
db8500_prcmu_probe should not be marked as __init so remove the __init
annotation from fw_project_name and init_prcm_registers.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8838555089 ]
When building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x3d84a3b): Section mismatch in reference from
the function twl_probe() to the function
.init.text:unprotect_pm_master()
The function twl_probe() references
the function __init unprotect_pm_master().
This is often because twl_probe lacks a __init
annotation or the annotation of unprotect_pm_master is wrong.
Remove the __init annotation on the *protect_pm_master functions so
there is no more mismatch.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6587cdbd7 ]
When a connection is closing we receive on pvcalls_sk_state_change
notification. Instead of setting the connection as closed immediately
(-ENOTCONN), let's read one more time from it: pvcalls_conn_back_read
will set the connection as closed when necessary.
That way, we avoid races between pvcalls_sk_state_change and
pvcalls_back_ioworker.
Signed-off-by: Stefano Stabellini <stefanos@xilinx.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b40ee006fe ]
Use PLATFORM_DEVID_AUTO to number mfd cells while registering, so that
different instances are uniquely identified. This is required in order
to support registering of multiple instances of same ti_am335x_tscadc IP.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a08bf91ce2 upstream.
If the sysctl 'kernel.keys.maxkeys' is set to some number n, then
actually users can only add up to 'n - 1' keys. Likewise for
'kernel.keys.maxbytes' and the root_* versions of these sysctls. But
these sysctls are apparently supposed to be *maximums*, as per their
names and all documentation I could find -- the keyrings(7) man page,
Documentation/security/keys/core.rst, and all the mentions of EDQUOT
meaning that the key quota was *exceeded* (as opposed to reached).
Thus, fix the code to allow reaching the quotas exactly.
Fixes: 0b77f5bfb4 ("keys: make the keyring quotas controllable through /proc/sys")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 050c17f239 upstream.
The system call, get_mempolicy() [1], passes an unsigned long *nodemask
pointer and an unsigned long maxnode argument which specifies the length
of the user's nodemask array in bits (which is rounded up). The manual
page says that if the maxnode value is too small, get_mempolicy will
return EINVAL but there is no system call to return this minimum value.
To determine this value, some programs search /proc/<pid>/status for a
line starting with "Mems_allowed:" and use the number of digits in the
mask to determine the minimum value. A recent change to the way this line
is formatted [2] causes these programs to compute a value less than
MAX_NUMNODES so get_mempolicy() returns EINVAL.
Change get_mempolicy(), the older compat version of get_mempolicy(), and
the copy_nodes_to_user() function to use nr_node_ids instead of
MAX_NUMNODES, thus preserving the defacto method of computing the minimum
size for the nodemask array and the maxnode argument.
[1] http://man7.org/linux/man-pages/man2/get_mempolicy.2.html
[2] https://lore.kernel.org/lkml/1545405631-6808-1-git-send-email-longman@redhat.com
Link: http://lkml.kernel.org/r/20190211180245.22295-1-rcampbell@nvidia.com
Fixes: 4fb8e5b89bcbbbb ("include/linux/nodemask.h: use nr_node_ids (not MAX_NUMNODES) in __nodemask_pr_numnodes()")
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Cc: Waiman Long <longman@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fd3fd0a9b upstream.
The authorize reply can be empty, for example when the ticket used to
build the authorizer is too old and TAG_BADAUTHORIZER is returned from
the service. Calling ->verify_authorizer_reply() results in an attempt
to decrypt and validate (somewhat) random data in au->buf (most likely
the signature block from calc_signature()), which fails and ends up in
con_fault_finish() with !con->auth_retry. The ticket isn't invalidated
and the connection is retried again and again until a new ticket is
obtained from the monitor:
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
Let TAG_BADAUTHORIZER handler kick in and increment con->auth_retry.
Cc: stable@vger.kernel.org
Fixes: 5c056fdc5b ("libceph: verify authorize reply on connect")
Link: https://tracker.ceph.com/issues/20164
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83e37e0bdd upstream.
The starting of AP interface can fail due to invalid
beacon interval, which does not match the minimum gcd
requirement set by the wifi driver. In such case, the
beacon interval of that interface gets updated with
that invalid beacon interval.
The next time that interface is brought up in AP mode,
an interface combination check is performed and the
beacon interval is taken from the previously set value.
In a case where an invalid beacon interval, i.e. a beacon
interval value which does not satisfy the minimum gcd criteria
set by the driver, is set, all the subsequent trials to
bring that interface in AP mode will fail, even if the
subsequent trials have a valid beacon interval.
To avoid this, in case of a failure in bringing up an
interface in AP mode due to interface combination error,
the interface beacon interval which is stored in bss
conf, needs to be restored with the last working value
of beacon interval.
Tested on ath10k using WCN3990.
Cc: stable@vger.kernel.org
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13443154f6 upstream.
The function prototype used to call JITed eBPF code (ie. the type of the
struct bpf_prog bpf_func field) returns an unsigned int. The MIPS n64
ABI that MIPS64 kernels target defines that 32 bit integers should
always be sign extended when passed in registers as either arguments or
return values.
This means that when returning any value which may not already be sign
extended (ie. of type REG_64BIT or REG_32BIT_ZERO_EX) we need to perform
that sign extension in order to comply with the n64 ABI. Without this we
see strange looking test failures from test_bpf.ko, such as:
test_bpf: #65 ALU64_MOV_X:
dst = 4294967295 jited:1 ret -1 != -1 FAIL (1 times)
Although the return value printed matches the expected value, this is
only because printf is only examining the least significant 32 bits of
the 64 bit register value we returned. The register holding the expected
value is sign extended whilst the v0 register was set to a zero extended
value by our JITed code, so when compared by a conditional branch
instruction the values are not equal.
We already handle this when the return value register is of type
REG_32BIT_ZERO_EX, so simply extend this to also cover REG_64BIT.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9c4 ("MIPS: Add missing file for eBPF JIT.")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e7382153f upstream.
The following commit
441dae8f2f ("tracing: Add support for display of tgid in trace output")
removed the call to print_event_info() from print_func_help_header_irq()
which results in the ftrace header not reporting the number of entries
written in the buffer. As this wasn't the original intent of the patch,
re-introduce the call to print_event_info() to restore the orginal
behaviour.
Link: http://lkml.kernel.org/r/20190214152950.4179-1-quentin.perret@arm.com
Acked-by: Joel Fernandes <joelaf@google.com>
Cc: stable@vger.kernel.org
Fixes: 441dae8f2f ("tracing: Add support for display of tgid in trace output")
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7afe6c1d4 upstream.
While trying to reproduce a reported kernel panic on arm64, I discovered
that AUTH_GSS basically doesn't work at all with older enctypes on arm64
systems with CONFIG_VMAP_STACK enabled. It turns out there still a few
places using stack memory with scatterlists, causing krb5_encrypt() and
krb5_decrypt() to produce incorrect results (or a BUG if CONFIG_DEBUG_SG
is enabled).
Tested with cthon on v4.0/v4.1/v4.2 with krb5/krb5i/krb5p using
des3-cbc-sha1 and arcfour-hmac-md5.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04c03114be ]
soukjin bae reported a crash in tcp_v4_err() handling
ICMP_DEST_UNREACH after tcp_write_queue_head(sk)
returned a NULL pointer.
Current logic should have prevented this :
if (seq != tp->snd_una || !icsk->icsk_retransmits ||
!icsk->icsk_backoff || fastopen)
break;
Problem is the write queue might have been purged
and icsk_backoff has not been cleared.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: soukjin bae <soukjin.bae@samsung.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3bed3cc415 ]
This patch addresses the fact that there are drivers, specifically tun,
that will call into the network page fragment allocators with buffer sizes
that are not cache aligned. Doing this could result in data alignment
and DMA performance issues as these fragment pools are also shared with the
skb allocator and any other devices that will use napi_alloc_frags or
netdev_alloc_frags.
Fixes: ffde7328a3 ("net: Split netdev_alloc_frag into __alloc_page_frag and add __napi_alloc_frag")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2c4cc97123 ]
ICMP handlers are not very often stressed, we should
make them more resilient to bugs that might surface in
the future.
If there is no packet in retransmit queue, we should
avoid a NULL deref.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: soukjin bae <soukjin.bae@samsung.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 816db76635 ]
When fail, translate_desc() returns negative value, otherwise the
number of iovs. So we should fail when the return value is negative
instead of a blindly check against zero.
Detected by CoverityScan, CID# 1442593: Control flow issues (DEADCODE)
Fixes: cc5e710759 ("vhost: log dirty page correctly")
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 224babd62d6f19581757a6d8bae3bf9501fc10de ]
GMAC IP is little-endian and used on several kind of CPU (big or little
endian). Main callbacks functions of the stmmac drivers take care about
it. It was not the case for dwmac4_get_timestamp function.
Fixes: ba1ffd74df ("stmmac: fix PTP support for GMAC4")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a7493e58a ]
We are saving the status of EEE even before we try to enable it. This
leads to a race with XMIT function that tries to arm EEE timer before we
set it up.
Fix this by only saving the EEE parameters after all operations are
performed with success.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 197f9ab7f0 ]
Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.
With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Fixes: f411a6160b ("net: phy: Add gmiitorgmii converter support")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b89ea9c59 ]
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 289460404f ]
The function-local variable "delay" enters the loop interpreted as delay
in bits. However, inside the loop it gets overwritten by the result of
mlxsw_sp_pg_buf_delay_get(), and thus leaves the loop as quantity in
cells. Thus on second and further loop iterations, the headroom for a
given priority is configured with a wrong size.
Fix by introducing a loop-local variable, delay_cells. Rename thres to
thres_cells for consistency.
Fixes: f417f04da5 ("mlxsw: spectrum: Refactor port buffer configuration")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07bd14ccc3 ]
Add the missing unlock before return from function set_fan_div()
in the error handling case.
Fixes: c9c6391551 ("hwmon: (lm80) fix a missing check of the status of SMBus read")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4179cb5a4c ]
netif_rx() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Note this patch also fixes a small issue that came
with commit ce6502a8f9 ("vxlan: fix a use after free
in vxlan_encap_bypass"), since the dev->stats.rx_dropped
change was done on the wrong device.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Fixes: ce6502a8f9 ("vxlan: fix a use after free in vxlan_encap_bypass")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petr Machata <petrm@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 225d946426 ]
In the unlikely event that the kmalloc call in vmci_transport_socket_init()
fails, we end-up calling vmci_transport_destruct() with a NULL vmci_trans()
and oopsing.
This change addresses the above explicitly checking for zero vmci_trans()
at destruction time.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c09551c6ff ]
According to the algorithm described in the comment block at the
beginning of ip_rt_send_redirect, the host should try to send
'ip_rt_redirect_number' ICMP redirect packets with an exponential
backoff and then stop sending them at all assuming that the destination
ignores redirects.
If the device has previously sent some ICMP error packets that are
rate-limited (e.g TTL expired) and continues to receive traffic,
the redirect packets will never be transmitted. This happens since
peer->rate_tokens will be typically greater than 'ip_rt_redirect_number'
and so it will never be reset even if the redirect silence timeout
(ip_rt_redirect_silence) has elapsed without receiving any packet
requiring redirects.
Fix it by using a dedicated counter for the number of ICMP redirect
packets that has been sent by the host
I have not been able to identify a given commit that introduced the
issue since ip_rt_send_redirect implements the same rate-limiting
algorithm from commit 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e75913c93f ]
Follow those steps:
# ip addr add 2001:123::1/32 dev eth0
# ip addr add 2001:123:456::2/64 dev eth0
# ip addr del 2001:123::1/32 dev eth0
# ip addr del 2001:123:456::2/64 dev eth0
and then prefix route of 2001:123::1/32 will still exist.
This is because ipv6_prefix_equal in check_cleanup_prefix_route
func does not check whether two IPv6 addresses have the same
prefix length. If the prefix of one address starts with another
shorter address prefix, even though their prefix lengths are
different, the return value of ipv6_prefix_equal is true.
Here I add a check of whether two addresses have the same prefix
to decide whether their prefixes are equal.
Fixes: 5b84efecb7 ("ipv6 addrconf: don't cleanup prefix route for IFA_F_NOPREFIXROUTE")
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c0db24cc4 ]
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit da360299b6 upstream.
This fixes a compile problem of some user space applications by not
including linux/libc-compat.h in uapi/if_ether.h.
linux/libc-compat.h checks which "features" the header files, included
from the libc, provide to make the Linux kernel uapi header files only
provide no conflicting structures and enums. If a user application mixes
kernel headers and libc headers it could happen that linux/libc-compat.h
gets included too early where not all other libc headers are included
yet. Then the linux/libc-compat.h would not prevent all the
redefinitions and we run into compile problems.
This patch removes the include of linux/libc-compat.h from
uapi/if_ether.h to fix the recently introduced case, but not all as this
is more or less impossible.
It is no problem to do the check directly in the if_ether.h file and not
in libc-compat.h as this does not need any fancy glibc header detection
as glibc never provided struct ethhdr and should define
__UAPI_DEF_ETHHDR by them self when they will provide this.
The following test program did not compile correctly any more:
#include <linux/if_ether.h>
#include <netinet/in.h>
#include <linux/in.h>
int main(void)
{
return 0;
}
Fixes: 6926e041a8 ("uapi/if_ether.h: prevent redefinition of struct ethhdr")
Reported-by: Guillaume Nault <g.nault@alphalink.fr>
Cc: <stable@vger.kernel.org> # 4.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a86caa9ba5 upstream.
Sven Eckelmann reported an issue with the current IPQ4019 pinctrl.
Setting up any gpio-hog in the device-tree for his device would
"kill the bootup completely":
| [ 0.477838] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 0.499828] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferring probe
| [ 1.298883] requesting hog GPIO enable USB2 power (chip 1000000.pinctrl, offset 58) failed, -517
| [ 1.299609] gpiochip_add_data: GPIOs 0..99 (1000000.pinctrl) failed to register
| [ 1.308589] ipq4019-pinctrl 1000000.pinctrl: Failed register gpiochip
| [ 1.316586] msm_serial 78af000.serial: could not find pctldev for node /soc/pinctrl@1000000/serial_pinmux, deferring probe
| [ 1.322415] spi_qup 78b5000.spi: could not find pctldev for node /soc/pinctrl@1000000/spi_0_pinmux, deferri
This was also verified on a RT-AC58U (IPQ4018) which would
no longer boot, if a gpio-hog was specified. (Tried forcing
the USB LED PIN (GPIO0) to high.).
The problem is that Pinctrl+GPIO registration is currently
peformed in the following order in pinctrl-msm.c:
1. pinctrl_register()
2. gpiochip_add()
3. gpiochip_add_pin_range()
The actual error code -517 == -EPROBE_DEFER is coming from
pinctrl_get_device_gpio_range(), which is called through:
gpiochip_add
of_gpiochip_add
of_gpiochip_scan_gpios
gpiod_hog
gpiochip_request_own_desc
__gpiod_request
chip->request
gpiochip_generic_request
pinctrl_gpio_request
pinctrl_get_device_gpio_range
pinctrl_get_device_gpio_range() is unable to find any valid
pin ranges, since nothing has been added to the pinctrldev_list yet.
so the range can't be found, and the operation fails with -EPROBE_DEFER.
This patch fixes the issue by adding the "gpio-ranges" property to
the pinctrl device node of all upstream Qcom SoC. The pin ranges are
then added by the gpio core.
In order to remain compatible with older, existing DTs (and ACPI)
a check for the "gpio-ranges" property has been added to
msm_gpio_init(). This prevents the driver of adding the same entry
to the pinctrldev_list twice.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da791a6675 upstream.
Stefan reported, that the glibc tst-robustpi4 test case fails
occasionally. That case creates the following race between
sys_exit() and sys_futex_lock_pi():
CPU0 CPU1
sys_exit() sys_futex()
do_exit() futex_lock_pi()
exit_signals(tsk) No waiters:
tsk->flags |= PF_EXITING; *uaddr == 0x00000PID
mm_release(tsk) Set waiter bit
exit_robust_list(tsk) { *uaddr = 0x80000PID;
Set owner died attach_to_pi_owner() {
*uaddr = 0xC0000000; tsk = get_task(PID);
} if (!tsk->flags & PF_EXITING) {
... attach();
tsk->flags |= PF_EXITPIDONE; } else {
if (!(tsk->flags & PF_EXITPIDONE))
return -EAGAIN;
return -ESRCH; <--- FAIL
}
ESRCH is returned all the way to user space, which triggers the glibc test
case assert. Returning ESRCH unconditionally is wrong here because the user
space value has been changed by the exiting task to 0xC0000000, i.e. the
FUTEX_OWNER_DIED bit is set and the futex PID value has been cleared. This
is a valid state and the kernel has to handle it, i.e. taking the futex.
Cure it by rereading the user space value when PF_EXITING and PF_EXITPIDONE
is set in the task which 'owns' the futex. If the value has changed, let
the kernel retry the operation, which includes all regular sanity checks
and correctly handles the FUTEX_OWNER_DIED case.
If it hasn't changed, then return ESRCH as there is no way to distinguish
this case from malfunctioning user space. This happens when the exiting
task did not have a robust list, the robust list was corrupted or the user
space value in the futex was simply bogus.
Reported-by: Stefan Liebler <stli@linux.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200467
Link: https://lkml.kernel.org/r/20181210152311.986181245@linutronix.de
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ae280b4ee upstream.
When provisioning a new data block for a virtual block, either because
the block was previously unallocated or because we are breaking sharing,
if the whole block of data is being overwritten the bio that triggered
the provisioning is issued immediately, skipping copying or zeroing of
the data block.
When this bio completes the new mapping is inserted in to the pool's
metadata by process_prepared_mapping(), where the bio completion is
signaled to the upper layers.
This completion is signaled without first committing the metadata. If
the bio in question has the REQ_FUA flag set and the system crashes
right after its completion and before the next metadata commit, then the
write is lost despite the REQ_FUA flag requiring that I/O completion for
this request must only be signaled after the data has been committed to
non-volatile storage.
Fix this by deferring the completion of overwrite bios, with the REQ_FUA
flag set, until after the metadata has been committed.
Cc: stable@vger.kernel.org
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff0c129d3b upstream.
bio_sectors() returns the value in the units of 512-byte sectors (no
matter what the real sector size of the device). dm-crypt multiplies
bio_sectors() by on_disk_tag_size to calculate the space allocated for
integrity tags. If dm-crypt is running with sector size larger than
512b, it allocates more data than is needed.
Device Mapper trims the extra space when passing the bio to
dm-integrity, so this bug didn't result in any visible misbehavior.
But it must be fixed to avoid wasteful memory allocation for the block
integrity payload.
Fixes: ef43aa3806 ("dm crypt: add cryptographic data integrity protection (authenticated encryption)")
Cc: stable@vger.kernel.org # 4.12+
Reported-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
