commit 9d2c7203ff upstream.
In kernels compiled with CONFIG_PARAVIRT=n, the compiler re-orders the
DR7 read in exc_nmi() to happen before the call to sev_es_ist_enter().
This is problematic when running as an SEV-ES guest because in this
environment the DR7 read might cause a #VC exception, and taking #VC
exceptions is not safe in exc_nmi() before sev_es_ist_enter() has run.
The result is stack recursion if the NMI was caused on the #VC IST
stack, because a subsequent #VC exception in the NMI handler will
overwrite the stack frame of the interrupted #VC handler.
As there are no compiler barriers affecting the ordering of DR7
reads/writes, make the accesses to this register volatile, forbidding
the compiler to re-order them.
[ bp: Massage text, make them volatile too, to make sure some
aggressive compiler optimization pass doesn't discard them. ]
Fixes: 315562c9af ("x86/sev-es: Adjust #VC IST Stack on entering NMI handler")
Reported-by: Alexey Kardashevskiy <aik@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230127035616.508966-1-aik@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30d09b3131 upstream.
Before the commit fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
gadget driver.bus was unused. For whatever reason, many UDC drivers set
this field explicitly to NULL in udc_start(). With the newly added gadget
bus, doing this will crash the driver during the attach.
The problem was first reported, fixed and tested with OMAP UDC and g_ether.
Other drivers are changed based on code analysis only.
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable <stable@kernel.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230201220125.GD2415@darkstar.musicnaut.iki.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3489dbb696 upstream.
Patch series "Fixes for hugetlb mapcount at most 1 for shared PMDs".
This issue of mapcount in hugetlb pages referenced by shared PMDs was
discussed in [1]. The following two patches address user visible behavior
caused by this issue.
[1] https://lore.kernel.org/linux-mm/Y9BF+OCdWnCSilEu@monkey/
This patch (of 2):
A hugetlb page will have a mapcount of 1 if mapped by multiple processes
via a shared PMD. This is because only the first process increases the
map count, and subsequent processes just add the shared PMD page to their
page table.
page_mapcount is being used to decide if a hugetlb page is shared or
private in /proc/PID/smaps. Pages referenced via a shared PMD were
incorrectly being counted as private.
To fix, check for a shared PMD if mapcount is 1. If a shared PMD is found
count the hugetlb page as shared. A new helper to check for a shared PMD
is added.
[akpm@linux-foundation.org: simplification, per David]
[akpm@linux-foundation.org: hugetlb.h: include page_ref.h for page_count()]
Link: https://lkml.kernel.org/r/20230126222721.222195-2-mike.kravetz@oracle.com
Fixes: 25ee01a2fc ("mm: hugetlb: proc: add hugetlb-related fields to /proc/PID/smaps")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: James Houghton <jthoughton@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev>
Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f394c0e7d upstream.
GCC 13 will enable -fasynchronous-unwind-tables by default on riscv. In
the kernel, we don't have any use for unwind tables yet, so disable them.
More importantly, the .eh_frame section brings relocations
(R_RISC_32_PCREL, R_RISCV_SET{6,8,16}, R_RISCV_SUB{6,8,16}) into modules
that we are not prepared to handle.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Link: https://lore.kernel.org/r/mvmzg9xybqu.fsf@suse.de
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f0c17809a upstream.
Prefer usage of the PRIV_USER constant over the hard-coded value to set
the lowest 2 bits for the userspace privilege.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 5.16+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c151d5ed8e upstream.
The SID SRAM on at least some SoCs (A64 and D1) returns different values
when read with bus cycles narrower than 32 bits. This is not immediately
obvious, because memcpy_fromio() uses word-size accesses as long as
enough data is being copied.
The vendor driver always uses 32-bit MMIO reads, so do the same here.
This is faster than the register-based method, which is currently used
as a workaround on A64. And it fixes the values returned on D1, where
the SRAM method was being used.
The special case for the last word is needed to maintain .word_size == 1
for sysfs ABI compatibility, as noted previously in commit de2a3eaea5
("nvmem: sunxi_sid: Optimize register read-out method").
Fixes: 07ae4fde9e ("nvmem: sunxi_sid: Add support for D1 variant")
Cc: stable@vger.kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2acd031347 upstream.
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a53f945879 upstream.
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fc3562a99 upstream.
irq flood happen when run
cat /sys/bus/iio/devices/iio:device0/in_voltage1_raw
imx8qxp_adc_read_raw()
{
...
enable irq
/* adc start */
writel(1, adc->regs + IMX8QXP_ADR_ADC_SWTRIG);
^^^^ trigger irq flood.
wait_for_completion_interruptible_timeout();
readl(adc->regs + IMX8QXP_ADR_ADC_RESFIFO);
^^^^ clear irq here.
...
}
There is only FIFO watermark interrupt at this ADC controller.
IRQ line will be assert until software read data from FIFO.
So IRQ flood happen during wait_for_completion_interruptible_timeout().
Move FIFO read into irq handle to avoid irq flood.
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Cc: stable@vger.kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20221201140110.2653501-1-Frank.Li@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 101ca8d059 upstream.
The current implementation of rtc-efi is expecting all the 4
time services GET{SET}_TIME{WAKEUP} must be supported by UEFI
firmware. As per the EFI_RT_PROPERTIES_TABLE, the platform
specific implementations can choose to enable selective time
services based on the RTC device capabilities.
This patch does the following changes to provide GET/SET RTC
services on platforms that do not support the WAKEUP feature.
1) Relax time services cap check when creating a platform device.
2) Clear RTC_FEATURE_ALARM bit in the absence of WAKEUP services.
3) Conditional alarm entries in '/proc/driver/rtc'.
Cc: <stable@vger.kernel.org> # v6.0+
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Link: https://lore.kernel.org/r/20230102230630.192911-1-sdonthineni@nvidia.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 636ab417a7 upstream.
UEFI v2.10 introduces version 2 of the memory attributes table, which
turns the reserved field into a flags field, but is compatible with
version 1 in all other respects. So let's not complain about version 2
if we encounter it.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32e40f9506 upstream.
The DIAG 288 statement consumes an EBCDIC string the address of which is
passed in a register. Use a "memory" clobber to tell the compiler that
memory is accessed within the inline assembly.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe8973a3ad upstream.
With CONFIG_VMAP_STACK=y the stack is allocated from the vmalloc space.
Data passed to a hardware or a hypervisor interface that
requires V=R can no longer be allocated on the stack.
Use kmalloc() to get memory for a diag288 command.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f027cba82 upstream.
The timer for the transmission of isotp PDUs formerly had two functions:
1. send two consecutive frames with a given time gap
2. monitor the timeouts for flow control frames and the echo frames
This led to larger txstate checks and potentially to a problem discovered
by syzbot which enabled the panic_on_warn feature while testing.
The former 'txtimer' function is split into 'txfrtimer' and 'txtimer'
to handle the two above functionalities with separate timer callbacks.
The two simplified timers now run in one-shot mode and make the state
transitions (especially with isotp_rcv_echo) better understandable.
Fixes: 866337865f ("can: isotp: fix tx state handling for echo tx processing")
Reported-by: syzbot+5aed6c3aaba661f5b917@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # >= v6.0
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230104145701.2422-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1febf88ef9 upstream.
Currently, when resetting the USB modem via AT commands, the modem is
no longer re-connected.
This problem is caused by the incorrect description of the USB_OTG2_OC
pad. It should have pull-up enabled, hysteresis enabled and the
property 'over-current-active-low' should be passed.
With this change, the USB modem can be successfully re-connected
after a reset.
Cc: stable@vger.kernel.org
Fixes: 9ac0ae97e3 ("ARM: dts: imx7d-smegw01: Add support for i.MX7D SMEGW01 board")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99f1c46011 upstream.
netvsc_dma_map() and netvsc_dma_unmap() currently check the cp_partial
flag and adjust the page_count so that pagebuf entries for the RNDIS
portion of the message are skipped when it has already been copied into
a send buffer. But this adjustment has already been made by code in
netvsc_send(). The duplicate adjustment causes some pagebuf entries to
not be mapped. In a normal VM, this doesn't break anything because the
mapping doesn’t change the PFN. But in a Confidential VM,
dma_map_single() does bounce buffering and provides a different PFN.
Failing to do the mapping causes the wrong PFN to be passed to Hyper-V,
and various errors ensue.
Fix this by removing the duplicate adjustment in netvsc_dma_map() and
netvsc_dma_unmap().
Fixes: 846da38de0 ("net: netvsc: Add Isolation VM support for netvsc driver")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1675135986-254490-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5ae880384 upstream.
It was found that the check to see if a partition could use up all
the cpus from the parent cpuset in update_parent_subparts_cpumask()
was incorrect. As a result, it is possible to leave parent with no
effective cpu left even if there are tasks in the parent cpuset. This
can lead to system panic as reported in [1].
Fix this probem by updating the check to fail the enabling the partition
if parent's effective_cpus is a subset of the child's cpus_allowed.
Also record the error code when an error happens in update_prstate()
and add a test case where parent partition and child have the same cpu
list and parent has task. Enabling partition in the child will fail in
this case.
[1] https://www.spinics.net/lists/cgroups/msg36254.html
Fixes: f0af1bfc27 ("cgroup/cpuset: Relax constraints to partition & cpus changes")
Cc: stable@vger.kernel.org # v6.1
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
