[ Upstream commit 1bb5a99e1f3fd27accb804aa0443a789161f843c ]
Performing a dummy read ensures that the register write operation is fully
completed, mitigating any potential bus delays that could otherwise impact
the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to
control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application
sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on
a delay function to ensure the clock frequency does not exceed 1 MHz.
However, this can lead to rapid toggling of the GPIO because the write
operation is POSTed and does not wait for a bus acknowledgment.
Fixes: 361b79119a ("gpio: Add Aspeed driver")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f3dcd0d39affe5b9ba1c351ce0e270c8bdd5109 ]
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4b294f88a32438baf31762441f3dd1c996778be ]
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca8c1f71c10193c270f772d70d34b15ad765d6a8 ]
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 680a8217dc00dc7e7da57888b3c053289b60eb2b ]
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42fb3acf6826c6764ba79feb6e15229b43fd2f9f ]
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b98 ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ebc25d8b053a208786295bab58abbb66b39c318 ]
The function proc_thermal_add() adds sysfs entries for power limits.
The feature mask of available features is not present at that time, so
it cannot be used by proc_thermal_add() to selectively create sysfs
attributes.
The feature mask is set by proc_thermal_mmio_add(), so modify the code
to call it before proc_thermal_add() so as to allow the latter to use
the feature mask.
There is no functional impact with this change.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 99ca0b57e49f ("thermal: intel: int340x: processor: Fix warning during module unload")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08d1914293dae38350b8088980e59fbc699a72fe ]
rfcomm_sk_state_change attempts to use sock_lock so it must never be
called with it locked but rfcomm_sock_ioctl always attempt to lock it
causing the following trace:
======================================================
WARNING: possible circular locking dependency detected
6.8.0-syzkaller-08951-gfe46a7dd189e #0 Not tainted
------------------------------------------------------
syz-executor386/5093 is trying to acquire lock:
ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: lock_sock include/net/sock.h:1671 [inline]
ffff88807c396258 (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+.}-{0:0}, at: rfcomm_sk_state_change+0x5b/0x310 net/bluetooth/rfcomm/sock.c:73
but task is already holding lock:
ffff88807badfd28 (&d->lock){+.+.}-{3:3}, at: __rfcomm_dlc_close+0x226/0x6a0 net/bluetooth/rfcomm/core.c:491
Reported-by: syzbot+d7ce59b06b3eb14fd218@syzkaller.appspotmail.com
Tested-by: syzbot+d7ce59b06b3eb14fd218@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=d7ce59b06b3eb14fd218
Fixes: 3241ad820d ("[Bluetooth] Add timestamp support to L2CAP, RFCOMM and SCO")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f49d14ec41ce7be647028d7d34dea727af55272 ]
Currently, the second bridge command overwrites the first one.
Fix this by adding this VID to the interface behind $swp2.
The one_bridge_two_pvids() test intends to check that there is no
leakage of traffic between bridge ports which have a single VLAN - the
PVID VLAN.
Because of a typo, port $swp1 is configured with a PVID twice (second
command overwrites first), and $swp2 isn't configured at all (and since
the bridge vlan_default_pvid property is set to 0, this port will not
have a PVID at all, so it will drop all untagged and priority-tagged
traffic).
So, instead of testing the configuration that was intended, we are
testing a different one, where one port has PVID 2 and the other has
no PVID. This incorrect version of the test should also pass, but is
ineffective for its purpose, so fix the typo.
This typo has an impact on results of the test,
potentially leading to wrong conclusions regarding
the functionality of a network device.
The tests results:
TEST: Switch ports in VLAN-aware bridge with different PVIDs:
Unicast non-IP untagged [ OK ]
Multicast non-IP untagged [ OK ]
Broadcast non-IP untagged [ OK ]
Unicast IPv4 untagged [ OK ]
Multicast IPv4 untagged [ OK ]
Unicast IPv6 untagged [ OK ]
Multicast IPv6 untagged [ OK ]
Unicast non-IP VID 1 [ OK ]
Multicast non-IP VID 1 [ OK ]
Broadcast non-IP VID 1 [ OK ]
Unicast IPv4 VID 1 [ OK ]
Multicast IPv4 VID 1 [ OK ]
Unicast IPv6 VID 1 [ OK ]
Multicast IPv6 VID 1 [ OK ]
Unicast non-IP VID 4094 [ OK ]
Multicast non-IP VID 4094 [ OK ]
Broadcast non-IP VID 4094 [ OK ]
Unicast IPv4 VID 4094 [ OK ]
Multicast IPv4 VID 4094 [ OK ]
Unicast IPv6 VID 4094 [ OK ]
Multicast IPv6 VID 4094 [ OK ]
Fixes: 476a4f05d9 ("selftests: forwarding: add a no_forwarding.sh test")
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kacper Ludwinski <kac.ludwinski@icloud.com>
Link: https://patch.msgid.link/20241002051016.849-1-kac.ludwinski@icloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b41b4cbd9655bcebcce941bef3601db8110335be ]
Fix tcp_enter_recovery() so that if there are no retransmits out then
we zero retrans_stamp when entering fast recovery. This is necessary
to fix two buggy behaviors.
Currently a non-zero retrans_stamp value can persist across multiple
back-to-back loss recovery episodes. This is because we generally only
clears retrans_stamp if we are completely done with loss recoveries,
and get to tcp_try_to_open() and find !tcp_any_retrans_done(sk). This
behavior causes two bugs:
(1) When a loss recovery episode (CA_Loss or CA_Recovery) is followed
immediately by a new CA_Recovery, the retrans_stamp value can persist
and can be a time before this new CA_Recovery episode starts. That
means that timestamp-based undo will be using the wrong retrans_stamp
(a value that is too old) when comparing incoming TS ecr values to
retrans_stamp to see if the current fast recovery episode can be
undone.
(2) If there is a roughly minutes-long sequence of back-to-back fast
recovery episodes, one after another (e.g. in a shallow-buffered or
policed bottleneck), where each fast recovery successfully makes
forward progress and recovers one window of sequence space (but leaves
at least one retransmit in flight at the end of the recovery),
followed by several RTOs, then the ETIMEDOUT check may be using the
wrong retrans_stamp (a value set at the start of the first fast
recovery in the sequence). This can cause a very premature ETIMEDOUT,
killing the connection prematurely.
This commit changes the code to zero retrans_stamp when entering fast
recovery, when this is known to be safe (no retransmits are out in the
network). That ensures that when starting a fast recovery episode, and
it is safe to do so, retrans_stamp is set when we send the fast
retransmit packet. That addresses both bug (1) and bug (2) by ensuring
that (if no retransmits are out when we start a fast recovery) we use
the initial fast retransmit of this fast recovery as the time value
for undo and ETIMEDOUT calculations.
This makes intuitive sense, since the start of a new fast recovery
episode (in a scenario where no lost packets are out in the network)
means that the connection has made forward progress since the last RTO
or fast recovery, and we should thus "restart the clock" used for both
undo and ETIMEDOUT logic.
Note that if when we start fast recovery there *are* retransmits out
in the network, there can still be undesirable (1)/(2) issues. For
example, after this patch we can still have the (1) and (2) problems
in cases like this:
+ round 1: sender sends flight 1
+ round 2: sender receives SACKs and enters fast recovery 1,
retransmits some packets in flight 1 and then sends some new data as
flight 2
+ round 3: sender receives some SACKs for flight 2, notes losses, and
retransmits some packets to fill the holes in flight 2
+ fast recovery has some lost retransmits in flight 1 and continues
for one or more rounds sending retransmits for flight 1 and flight 2
+ fast recovery 1 completes when snd_una reaches high_seq at end of
flight 1
+ there are still holes in the SACK scoreboard in flight 2, so we
enter fast recovery 2, but some retransmits in the flight 2 sequence
range are still in flight (retrans_out > 0), so we can't execute the
new retrans_stamp=0 added here to clear retrans_stamp
It's not yet clear how to fix these remaining (1)/(2) issues in an
efficient way without breaking undo behavior, given that retrans_stamp
is currently used for undo and ETIMEDOUT. Perhaps the optimal (but
expensive) strategy would be to set retrans_stamp to the timestamp of
the earliest outstanding retransmit when entering fast recovery. But
at least this commit makes things better.
Note that this does not change the semantics of retrans_stamp; it
simply makes retrans_stamp accurate in some cases where it was not
before:
(1) Some loss recovery, followed by an immediate entry into a fast
recovery, where there are no retransmits out when entering the fast
recovery.
(2) When a TFO server has a SYNACK retransmit that sets retrans_stamp,
and then the ACK that completes the 3-way handshake has SACK blocks
that trigger a fast recovery. In this case when entering fast recovery
we want to zero out the retrans_stamp from the TFO SYNACK retransmit,
and set the retrans_stamp based on the timestamp of the fast recovery.
We introduce a tcp_retrans_stamp_cleanup() helper, because this
two-line sequence already appears in 3 places and is about to appear
in 2 more as a result of this bug fix patch series. Once this bug fix
patches series in the net branch makes it into the net-next branch
we'll update the 3 other call sites to use the new helper.
This is a long-standing issue. The Fixes tag below is chosen to be the
oldest commit at which the patch will apply cleanly, which is from
Linux v3.5 in 2012.
Fixes: 1fbc340514 ("tcp: early retransmit: tcp_enter_recovery()")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241001200517.2756803-3-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e37ab7373696e650d3b6262a5b882aadad69bb9e ]
Fix the TCP loss recovery undo logic in tcp_packet_delayed() so that
it can trigger undo even if TSQ prevents a fast recovery episode from
reaching tcp_retransmit_skb().
Geumhwan Yu <geumhwan.yu@samsung.com> recently reported that after
this commit from 2019:
commit bc9f38c832 ("tcp: avoid unconditional congestion window undo
on SYN retransmit")
...and before this fix we could have buggy scenarios like the
following:
+ Due to reordering, a TCP connection receives some SACKs and enters a
spurious fast recovery.
+ TSQ prevents all invocations of tcp_retransmit_skb(), because many
skbs are queued in lower layers of the sending machine's network
stack; thus tp->retrans_stamp remains 0.
+ The connection receives a TCP timestamp ECR value echoing a
timestamp before the fast recovery, indicating that the fast
recovery was spurious.
+ The connection fails to undo the spurious fast recovery because
tp->retrans_stamp is 0, and thus tcp_packet_delayed() returns false,
due to the new logic in the 2019 commit: commit bc9f38c832 ("tcp:
avoid unconditional congestion window undo on SYN retransmit")
This fix tweaks the logic to be more similar to the
tcp_packet_delayed() logic before bc9f38c832, except that we take
care not to be fooled by the FLAG_SYN_ACKED code path zeroing out
tp->retrans_stamp (the bug noted and fixed by Yuchung in
bc9f38c832).
Note that this returns the high-level behavior of tcp_packet_delayed()
to again match the comment for the function, which says: "Nothing was
retransmitted or returned timestamp is less than timestamp of the
first retransmission." Note that this comment is in the original
2005-04-16 Linux git commit, so this is evidently long-standing
behavior.
Fixes: bc9f38c832 ("tcp: avoid unconditional congestion window undo on SYN retransmit")
Reported-by: Geumhwan Yu <geumhwan.yu@samsung.com>
Diagnosed-by: Geumhwan Yu <geumhwan.yu@samsung.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241001200517.2756803-2-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a842e443ca8184f2dc82ab307b43a8b38defd6a5 ]
When configuring the fiber port, the DP83869 PHY driver incorrectly
calls linkmode_set_bit() with a bit mask (1 << 10) rather than a bit
number (10). This corrupts some other memory location -- in case of
arm64 the priv pointer in the same structure.
Since the advertising flags are updated from supported at the end of the
function the incorrect line isn't needed at all and can be removed.
Fixes: a29de52ba2 ("net: dp83869: Add ability to advertise Fiber connection")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241002161807.440378-1-inguin@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dbf1f341b6b35bcc20ff95b6b315e509f6c5369 ]
The math in "rc_list->rcl_nrefcalls * 2 * sizeof(uint32_t)" could have an
integer overflow. Add bounds checking on rc_list->rcl_nrefcalls to fix
that.
Fixes: 4aece6a19c ("nfs41: cb_sequence xdr implementation")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eae2c136cb624e4050092feb59f18159b4f2512 ]
There is a bug currently when there are more than one VLAN defined
and any reset that affects the PF is initiated, after the reset rebuild
no traffic will pass on any VLAN but the last one created.
This is caused by the iteration though the VLANs during replay each
clearing the vsi_map bitmap of the VSI that is being replayed. The
problem is that during rhe replay, the pointer to the vsi_map bitmap
is used by each successive vlan to determine if it should be replayed
on this VSI.
The logic was that the replay of the VLAN would replace the bit in the map
before the next VLAN would iterate through. But, since the replay copies
the old bitmap pointer to filt_replay_rules and creates a new one for the
recreated VLANS, it does not do this, and leaves the old bitmap broken
to be used to replay the remaining VLANs.
Since the old bitmap will be cleaned up in post replay cleanup, there is
no need to alter it and break following VLAN replay, so don't clear the
bit.
Fixes: 334cb0626d ("ice: Implement VSI replay framework")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc0d0f885aa422f621bc1c2124133eff566b0bc8 ]
NeilBrown says:
> The handling of NFSD_FILE_CACHE_UP is strange. nfsd_file_cache_init()
> sets it, but doesn't clear it on failure. So if nfsd_file_cache_init()
> fails for some reason, nfsd_file_cache_shutdown() would still try to
> clean up if it was called.
Reported-by: NeilBrown <neilb@suse.de>
Fixes: c7b824c3d0 ("NFSD: Replace the "init once" mechanism")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e140cb602 ]
The different VOP variants support different maximum resolutions. Reject
resolutions that are not supported by a specific variant.
This hasn't been a problem in the upstream driver so far as 1920x1080
has been the maximum resolution supported by the HDMI driver and that
resolution is supported by all VOP variants. Now with higher resolutions
supported in the HDMI driver we have to limit the resolutions to the
ones supported by the VOP.
The actual maximum resolutions are taken from the Rockchip downstream
Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[dropped the vdisplay > height check after talking to Sascha, as according to
the vendor code "Actually vop hardware has no output height limit"
(from vendor commit "drm/rockchip: vop: get rid of max_output.height check")
and the height-check broke the px30-minievb display]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216102447.582905-2-s.hauer@pengutronix.de
Stable-dep-of: 6ed51ba95e27 ("drm/rockchip: vop: enable VOP_FEATURE_INTERNAL_RGB on RK3066")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cf14f5a2746c19455ce9cb44341b5527b5e19c3 ]
The values of the variables xres and yres are placed in strbuf.
These variables are obtained from strbuf1.
The strbuf1 array contains digit characters
and a space if the array contains non-digit characters.
Then, when executing sprintf(strbuf, "%ux%ux8", xres, yres);
more than 16 bytes will be written to strbuf.
It is suggested to increase the size of the strbuf array to 24.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Shumilin <shum.sdl@nppct.ru>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff599ef6970ee000fa5bc38d02fa5ff5f3fc7575 ]
[WHAT & HOW]
se is null checked previously in the same function, indicating
it might be null; therefore, it must be checked when used again.
This fixes 1 FORWARD_NULL issue reported by Coverity.
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a3c84f71680684c1d41abb92db05f95c09111e8 ]
Deleting an NPIV instance requires all fabric ndlps to be released before
an NPIV's resources can be torn down. Failure to release fabric ndlps
beforehand opens kref imbalance race conditions. Fix by forcing the DA_ID
to complete synchronously with usage of wait_queue.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-6-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93bcc5f3984bf4f51da1529700aec351872dbfff ]
During HBA stress testing, a spam of received PLOGIs exposes a resource
recovery bug causing leakage of lpfc_sqlq entries from the global
phba->sli4_hba.lpfc_els_sgl_list.
The issue is in lpfc_els_flush_cmd(), where the driver attempts to recover
outstanding ELS sgls when walking the txcmplq. Only CMD_ELS_REQUEST64_CRs
and CMD_GEN_REQUEST64_CRs are added to the abort and cancel lists. A check
for CMD_XMIT_ELS_RSP64_WQE is missing in order to recover LS_ACC usages of
the phba->sli4_hba.lpfc_els_sgl_list too.
Fix by adding CMD_XMIT_ELS_RSP64_WQE as part of the txcmplq walk when
adding WQEs to the abort and cancel list in lpfc_els_flush_cmd(). Also,
update naming convention from CRs to WQEs.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240912232447.45607-2-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25fbcd97cf52c3c9824d44b5c56c19673c3dd50 ]
If a pmem device is in a bad status, the driver side could wait for
host ack forever in virtio_pmem_flush(), causing the system to hang.
So add a status check in the beginning of virtio_pmem_flush() to return
early if the device is not activated.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Message-Id: <20240826215313.2673566-1-philipchen@chromium.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc56878ca1c288e49b5cbb43860a5938e3463654 ]
If CONFIG_BRIDGE_NETFILTER is not enabled, which is the case for x86_64
defconfig, then building nf_reject_ipv4.c and nf_reject_ipv6.c with W=1
using gcc-14 results in the following warnings, which are treated as
errors:
net/ipv4/netfilter/nf_reject_ipv4.c: In function 'nf_send_reset':
net/ipv4/netfilter/nf_reject_ipv4.c:243:23: error: variable 'niph' set but not used [-Werror=unused-but-set-variable]
243 | struct iphdr *niph;
| ^~~~
cc1: all warnings being treated as errors
net/ipv6/netfilter/nf_reject_ipv6.c: In function 'nf_send_reset6':
net/ipv6/netfilter/nf_reject_ipv6.c:286:25: error: variable 'ip6h' set but not used [-Werror=unused-but-set-variable]
286 | struct ipv6hdr *ip6h;
| ^~~~
cc1: all warnings being treated as errors
Address this by reducing the scope of these local variables to where
they are used, which is code only compiled when CONFIG_BRIDGE_NETFILTER
enabled.
Compile tested and run through netfilter selftests.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Closes: https://lore.kernel.org/netfilter-devel/20240906145513.567781-1-andriy.shevchenko@linux.intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4058c39bd176daf11a826802d940d86292a6b02b ]
The issue is that before entering the crash kernel, the DWC USB controller
did not perform operations such as resetting the interrupt mask bits.
After entering the crash kernel,before the USB interrupt handler
registration was completed while loading the DWC USB driver,an GINTSTS_SOF
interrupt was received.This triggered the misroute_irq process within the
GIC handling framework,ultimately leading to the misrouting of the
interrupt,causing it to be handled by the wrong interrupt handler
and resulting in the issue.
Summary:In a scenario where the kernel triggers a panic and enters
the crash kernel,it is necessary to ensure that the interrupt mask
bit is not enabled before the interrupt registration is complete.
If an interrupt reaches the CPU at this moment,it will certainly
not be handled correctly,especially in cases where this interrupt
is reported frequently.
Please refer to the Crashkernel dmesg information as follows
(the message on line 3 was added before devm_request_irq is
called by the dwc2_driver_probe function):
[ 5.866837][ T1] dwc2 JMIC0010:01: supply vusb_d not found, using dummy regulator
[ 5.874588][ T1] dwc2 JMIC0010:01: supply vusb_a not found, using dummy regulator
[ 5.882335][ T1] dwc2 JMIC0010:01: before devm_request_irq irq: [71], gintmsk[0xf300080e], gintsts[0x04200009]
[ 5.892686][ C0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.0-jmnd1.2_RC #18
[ 5.900327][ C0] Hardware name: CMSS HyperCard4-25G/HyperCard4-25G, BIOS 1.6.4 Jul 8 2024
[ 5.908836][ C0] Call trace:
[ 5.911965][ C0] dump_backtrace+0x0/0x1f0
[ 5.916308][ C0] show_stack+0x20/0x30
[ 5.920304][ C0] dump_stack+0xd8/0x140
[ 5.924387][ C0] pcie_xxx_handler+0x3c/0x1d8
[ 5.930121][ C0] __handle_irq_event_percpu+0x64/0x1e0
[ 5.935506][ C0] handle_irq_event+0x80/0x1d0
[ 5.940109][ C0] try_one_irq+0x138/0x174
[ 5.944365][ C0] misrouted_irq+0x134/0x140
[ 5.948795][ C0] note_interrupt+0x1d0/0x30c
[ 5.953311][ C0] handle_irq_event+0x13c/0x1d0
[ 5.958001][ C0] handle_fasteoi_irq+0xd4/0x260
[ 5.962779][ C0] __handle_domain_irq+0x88/0xf0
[ 5.967555][ C0] gic_handle_irq+0x9c/0x2f0
[ 5.971985][ C0] el1_irq+0xb8/0x140
[ 5.975807][ C0] __setup_irq+0x3dc/0x7cc
[ 5.980064][ C0] request_threaded_irq+0xf4/0x1b4
[ 5.985015][ C0] devm_request_threaded_irq+0x80/0x100
[ 5.990400][ C0] dwc2_driver_probe+0x1b8/0x6b0
[ 5.995178][ C0] platform_drv_probe+0x5c/0xb0
[ 5.999868][ C0] really_probe+0xf8/0x51c
[ 6.004125][ C0] driver_probe_device+0xfc/0x170
[ 6.008989][ C0] device_driver_attach+0xc8/0xd0
[ 6.013853][ C0] __driver_attach+0xe8/0x1b0
[ 6.018369][ C0] bus_for_each_dev+0x7c/0xdc
[ 6.022886][ C0] driver_attach+0x2c/0x3c
[ 6.027143][ C0] bus_add_driver+0xdc/0x240
[ 6.031573][ C0] driver_register+0x80/0x13c
[ 6.036090][ C0] __platform_driver_register+0x50/0x5c
[ 6.041476][ C0] dwc2_platform_driver_init+0x24/0x30
[ 6.046774][ C0] do_one_initcall+0x50/0x25c
[ 6.051291][ C0] do_initcall_level+0xe4/0xfc
[ 6.055894][ C0] do_initcalls+0x80/0xa4
[ 6.060064][ C0] kernel_init_freeable+0x198/0x240
[ 6.065102][ C0] kernel_init+0x1c/0x12c
Signed-off-by: Shawn Shao <shawn.shao@jaguarmicro.com>
Link: https://lore.kernel.org/r/20240830031709.134-1-shawn.shao@jaguarmicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a54c441b46a0745683c2eef5a359d22856d27323 ]
For i.MX7D DRAM related mux clock, the clock source change should ONLY
be done done in low level asm code without accessing DRAM, and then
calling clk API to sync the HW clock status with clk tree, it should never
touch real clock source switch via clk API, so CLK_SET_PARENT_GATE flag
should NOT be added, otherwise, DRAM's clock parent will be disabled when
DRAM is active, and system will hang.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240607133347.3291040-8-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e954a1bd16102abc800629f9900715d8ec4c3130 ]
If there is a resource table device tree node, use the address as
the resource table address, otherwise use the address(where
.resource_table section loaded) inside the Cortex-M elf file.
And there is an update in NXP SDK that Resource Domain Control(RDC)
enabled to protect TCM, linux not able to write the TCM space when
updating resource table status and cause kernel dump. So use the address
from device tree could avoid kernel dump.
Note: NXP M4 SDK not check resource table update, so it does not matter
use whether resource table address specified in elf file or in device
tree. But to reflect the fact that if people specific resource table
address in device tree, it means people are aware and going to use it,
not the address specified in elf file.
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20240719-imx_rproc-v2-2-10d0268c7eb1@nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a9c97ab6b7e85697e0b74e86062192a5ffffd99 ]
Clear vb2_plane's memory related fields in __vb2_plane_dmabuf_put(),
including bytesused, length, fd and data_offset.
Remove the duplicated code in __prepare_dmabuf().
Signed-off-by: Yunke Cao <yunkec@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c6d097d830f779fc1725fbaa1314f20a7a07b4b ]
The new memory scheme page faults are requesting the driver to fetch
additinal pages to the faulted memory access.
This is done in order to prefetch pages before and after the area that
got the page fault, assuming this will reduce the total amount of page
faults.
The driver should ensure it handles only the pages that are within the
umem range.
Signed-off-by: Michael Guralnik <michaelgur@nvidia.com>
Link: https://patch.msgid.link/20240909100504.29797-5-michaelgur@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e51aded92d42784313ba16c12f4f88cc4f973bbb ]
In the switchtec_ntb_add function, it can call switchtec_ntb_init_sndev
function, then &sndev->check_link_status_work is bound with
check_link_status_work. switchtec_ntb_link_notification may be called
to start the work.
If we remove the module which will call switchtec_ntb_remove to make
cleanup, it will free sndev through kfree(sndev), while the work
mentioned above will be used. The sequence of operations that may lead
to a UAF bug is as follows:
CPU0 CPU1
| check_link_status_work
switchtec_ntb_remove |
kfree(sndev); |
| if (sndev->link_force_down)
| // use sndev
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in switchtec_ntb_remove.
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eac2ca2d682f94f46b1973bdf5e77d85d77b8e53 ]
In terms of normal application usage, this list will always be empty.
And if an application does overflow a bit, it'll have a few entries.
However, nothing obviously prevents syzbot from running a test case
that generates a ton of overflow entries, and then flushing them can
take quite a while.
Check for needing to reschedule while flushing, and drop our locks and
do so if necessary. There's no state to maintain here as overflows
always prune from head-of-list, hence it's fine to drop and reacquire
the locks at the end of the loop.
Link: https://lore.kernel.org/io-uring/66ed061d.050a0220.29194.0053.GAE@google.com/
Reported-by: syzbot+5fca234bd7eb378ff78e@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad380f6a0a5e82e794b45bb2eaec24ed51a56846 ]
I recently ended up with a warning on some compilers along the lines of
CC kernel/resource.o
In file included from include/linux/ioport.h:16,
from kernel/resource.c:15:
kernel/resource.c: In function 'gfr_start':
include/linux/minmax.h:49:37: error: conversion from 'long long unsigned int' to 'resource_size_t' {aka 'unsigned int'} changes value from '17179869183' to '4294967295' [-Werror=overflow]
49 | ({ type ux = (x); type uy = (y); __cmp(op, ux, uy); })
| ^
include/linux/minmax.h:52:9: note: in expansion of macro '__cmp_once_unique'
52 | __cmp_once_unique(op, type, x, y, __UNIQUE_ID(x_), __UNIQUE_ID(y_))
| ^~~~~~~~~~~~~~~~~
include/linux/minmax.h:161:27: note: in expansion of macro '__cmp_once'
161 | #define min_t(type, x, y) __cmp_once(min, type, x, y)
| ^~~~~~~~~~
kernel/resource.c:1829:23: note: in expansion of macro 'min_t'
1829 | end = min_t(resource_size_t, base->end,
| ^~~~~
kernel/resource.c: In function 'gfr_continue':
include/linux/minmax.h:49:37: error: conversion from 'long long unsigned int' to 'resource_size_t' {aka 'unsigned int'} changes value from '17179869183' to '4294967295' [-Werror=overflow]
49 | ({ type ux = (x); type uy = (y); __cmp(op, ux, uy); })
| ^
include/linux/minmax.h:52:9: note: in expansion of macro '__cmp_once_unique'
52 | __cmp_once_unique(op, type, x, y, __UNIQUE_ID(x_), __UNIQUE_ID(y_))
| ^~~~~~~~~~~~~~~~~
include/linux/minmax.h:161:27: note: in expansion of macro '__cmp_once'
161 | #define min_t(type, x, y) __cmp_once(min, type, x, y)
| ^~~~~~~~~~
kernel/resource.c:1847:24: note: in expansion of macro 'min_t'
1847 | addr <= min_t(resource_size_t, base->end,
| ^~~~~
cc1: all warnings being treated as errors
which looks like a real problem: our phys_addr_t is only 32 bits now, so
having 34-bit masks is just going to result in overflows.
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240731162159.9235-2-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43457ada98c824f310adb7bd96bd5f2fcd9a3279 ]
On chipsets with a second 'Integrated Device Function' SMBus controller use
a different adapter-name for the second IDF adapter.
This allows platform glue code which is looking for the primary i801
adapter to manually instantiate i2c_clients on to differentiate
between the 2.
This allows such code to find the primary i801 adapter by name, without
needing to duplicate the PCI-ids to feature-flags mapping from i2c-i801.c.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f92d67e23b8caa81f6322a2bad1d633b00ca000e ]
Driver code is leaking OF node reference from of_get_parent() in
bcm53573_ilp_init(). Usage of of_get_parent() is not needed in the
first place, because the parent node will not be freed while we are
processing given node (triggered by CLK_OF_DECLARE()). Thus fix the
leak by accessing parent directly, instead of of_get_parent().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240826065801.17081-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
