[ Upstream commit 52cc73e540 ]
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1239d8aa8 ]
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d8dc2c9676 ]
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a6 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6da3eced8c upstream.
Recently, the spinlock implementation grew a static key optimization,
but the jump_label.h header include was left out, leading to build
errors:
linux/arch/powerpc/include/asm/spinlock.h:44:7: error: implicit declaration of function ‘static_branch_unlikely’
44 | if (!static_branch_unlikely(&shared_processor))
This commit adds the missing header.
mpe: The build break is only seen with CONFIG_JUMP_LABEL=n.
Fixes: 656c21d6af ("powerpc/shared: Use static key to detect shared processor")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191223133147.129983-1-Jason@zx2c4.com
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0689faa8e ]
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: ff4a441990 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af1c0e4e00 ]
When a frame with NULL DSAP is received, llc_station_rcv is called.
In turn, llc_stat_ev_rx_null_dsap_xid_c is called to check if it is a NULL
XID frame. The return statement of llc_stat_ev_rx_null_dsap_xid_c returns 1
when the incoming frame is not a NULL XID frame and 0 otherwise. Hence, a
NULL XID response is returned unexpectedly, e.g. when the incoming frame is
a NULL TEST command.
To fix the error, simply remove the conditional operator.
A similar error in llc_stat_ev_rx_null_dsap_test_c is also fixed.
Signed-off-by: Chan Shu Tak, Alex <alexchan@task.com.hk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b7995a98a ]
When I doing fuzzy test, get the memleak report:
BUG: memory leak
unreferenced object 0xffff88837af80000 (size 4096):
comm "memleak", pid 3557, jiffies 4294817681 (age 112.499s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
20 00 00 00 10 01 00 00 00 00 00 00 01 00 00 00 ...............
backtrace:
[<000000001c894df8>] bio_alloc_bioset+0x393/0x590
[<000000008b139a3c>] bio_copy_user_iov+0x300/0xcd0
[<00000000a998bd8c>] blk_rq_map_user_iov+0x2f1/0x5f0
[<000000005ceb7f05>] blk_rq_map_user+0xf2/0x160
[<000000006454da92>] sg_common_write.isra.21+0x1094/0x1870
[<00000000064bb208>] sg_write.part.25+0x5d9/0x950
[<000000004fc670f6>] sg_write+0x5f/0x8c
[<00000000b0d05c7b>] __vfs_write+0x7c/0x100
[<000000008e177714>] vfs_write+0x1c3/0x500
[<0000000087d23f34>] ksys_write+0xf9/0x200
[<000000002c8dbc9d>] do_syscall_64+0x9f/0x4f0
[<00000000678d8e9a>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
If __blk_rq_map_user_iov() is failed in blk_rq_map_user_iov(),
the bio(s) which is allocated before this failing will leak. The
refcount of the bio(s) is init to 1 and increased to 2 by calling
bio_get(), but __blk_rq_unmap_user() only decrease it to 1, so
the bio cannot be freed. Fix it by calling blk_rq_unmap_user().
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00b39f698a ]
If for whatever reason the dasd_eckd_check_characteristics() function
exits after at least some paths have their configuration data
allocated those data is never freed again. In the error case the
device->private pointer is set to NULL and dasd_eckd_uncheck_device()
will exit without freeing the path data because of this NULL pointer.
Fix by calling dasd_eckd_clear_conf_data() for error cases.
Also use dasd_eckd_clear_conf_data() in dasd_eckd_uncheck_device()
to avoid code duplication.
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd4b3c83b9 ]
The max data count (mdc) is an unsigned 16-bit integer value as per AR
documentation and is received via ccw_device_get_mdc() for a specific
path mask from the CIO layer. The function itself also always returns a
positive mdc value or 0 in case mdc isn't supported or couldn't be
determined.
Though, the comment for this function describes a negative return value
to indicate failures.
As a result, the DASD device driver interprets the return value of
ccw_device_get_mdc() incorrectly. The error case is essentially a dead
code path.
To fix this behaviour, check explicitly for a return value of 0 and
change the comment for ccw_device_get_mdc() accordingly.
This fix merely enables the error code path in the DASD functions
get_fcx_max_data() and verify_fcx_max_data(). The actual functionality
stays the same and is still correct.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84c92365b2 ]
The driver forgets to call component_del in remove to match component_add
in probe.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c23587c92f ]
the purgatory must not rely on functions from the "old" kernel,
so we must disable kasan and friends. We also need to have a
separate copy of string.c as the default does not build memcmp
with KASAN.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4772f26db8 ]
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d558f0294 ]
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d55fd997 ]
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaf4fac478 ]
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04646aebd3 ]
Anything that walks all inodes on sb->s_inodes list without rescheduling
risks softlockups.
Previous efforts were made in 2 functions, see:
c27d82f fs/drop_caches.c: avoid softlockups in drop_pagecache_sb()
ac05fbb inode: don't softlockup when evicting inodes
but there hasn't been an audit of all walkers, so do that now. This
also consistently moves the cond_resched() calls to the bottom of each
loop in cases where it already exists.
One loop remains: remove_dquot_ref(), because I'm not quite sure how
to deal with that one w/o taking the i_lock.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 272a721030 ]
NULL expressions are taken to always be true, as implemented by the
expr_is_yes() macro and by several other functions in expr.c. As such,
they ought to be valid inputs to expr_eq(), which compares two
expressions.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aeea5eae4f ]
compilation failed with:
MODPOST vmlinux.o
WARNING: vmlinux.o(.text.unlikely+0xa0c): Section mismatch in reference from the function walk_lower_bus() to the function .init.text:walk_native_bus()
The function walk_lower_bus() references
the function __init walk_native_bus().
This is often because walk_lower_bus lacks a __init
annotation or the annotation of walk_native_bus is wrong.
FATAL: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
make[2]: *** [/home/svens/linux/parisc-linux/src/scripts/Makefile.modpost:64: __modpost] Error 1
make[1]: *** [/home/svens/linux/parisc-linux/src/Makefile:1077: vmlinux] Error 2
make[1]: Leaving directory '/home/svens/linux/parisc-linux/build'
make: *** [Makefile:179: sub-make] Error 2
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee699f89bd ]
Driver doesn't calculate total number of PFs configured on a
given engine correctly which messed up resources in the PFs
loaded on that engine, leading driver to exceed configuration
of resources (like vlan filters etc.) beyond the limit per
engine, which ended up with asserts from the firmware.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7113f796bb ]
Parity error from the hardware will cause PF to lose the state
of their VFs due to PF's internal reload and hardware reset following
the parity error. Restrict any configuration request from the VFs after
the parity as it could cause unexpected hardware behavior, only way
for VFs to recover would be to trigger FLR on VFs and reload them.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5133498f4a ]
Redirecting a packet from ingress to egress by using bpf_redirect
breaks if the egress interface has an fq qdisc installed. This is the same
problem as fixed in 'commit 8203e2d844 ("net: clear skb->tstamp in forwarding paths")
Clear skb->tstamp when redirecting into the egress path.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/bpf/20191213180817.2510-1-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37d02592f1 ]
The branch of qgroup_rescan_init which is executed from the mount
path prints wrong errors messages. The textual print out in case
BTRFS_QGROUP_STATUS_FLAG_RESCAN/BTRFS_QGROUP_STATUS_FLAG_ON are not
set are transposed. Fix it by exchanging their place.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fabc62323 ]
Some powerpc platforms (e.g. 85xx) limit DMA-able memory way below 4G.
If a system has more physical memory than this limit, the swiotlb
buffer is not addressable because it is allocated from memblock using
top-down mode.
Force memblock to bottom-up mode before calling swiotlb_init() to
ensure that the swiotlb buffer is DMA-able.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191204123524.22919-1-rppt@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe3300897c ]
Currently, open() is called from the user program and it calls the syscall
'sys_openat', not the 'sys_open'. This leads to an error of the program
of user side, due to the fact that the counter maps are zero since no
function such 'sys_open' is called.
This commit adds the kernel bpf program which are attached to the
tracepoint 'sys_enter_openat' and 'sys_enter_openat'.
Fixes: 1da236b6be ("bpf: add a test case for syscalls/sys_{enter|exit}_* tracepoints")
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bba1b2a890 ]
Previously, when this sample is added, commit 1c47910ef8
("samples/bpf: add perf_event+bpf example"), a symbol 'sys_read' and
'sys_write' has been used without no prefixes. But currently there are
no exact symbols with these under kallsyms and this leads to failure.
This commit changes exact compare to substring compare to keep compatible
with exact symbol or prefixed symbol.
Fixes: 1c47910ef8 ("samples/bpf: add perf_event+bpf example")
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191205080114.19766-2-danieltimlee@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6b16761c6 ]
The LCD panel on AM4 GP EVMs and ePOS boards seems to be
osd070t1718-19ts. The current dts files say osd057T0559-34ts. Possibly
the panel has changed since the early EVMs, or there has been a mistake
with the panel type.
Update the DT files accordingly.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c52c91bb9a ]
When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.
Fix this by updating appropriate bits whenever active CS changes.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c74751f4c3 ]
If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30e647a764 ]
During definition of the CPU thermal zone of BCM283x SoC family there
was a misunderstanding of the meaning "criticial trip point" and the
thermal throttling range of the VideoCore firmware. The latter one takes
effect when the core temperature is at least 85 degree celsius or higher
So the current critical trip point doesn't make sense, because the
thermal shutdown appears before the firmware has a chance to throttle
the ARM core(s).
Fix these unwanted shutdowns by increasing the critical trip point
to a value which shouldn't be reached with working thermal throttling.
Fixes: 0fe4d2181c ("ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cc6c8d4a9 ]
Fix multiple kprobe event testcase to work it correctly.
There are 2 bugfixes.
- Since `wc -l FILE` returns not only line number but also
FILE filename, following "if" statement always failed.
Fix this bug by replacing it with 'cat FILE | wc -l'
- Since "while do-done loop" block with pipeline becomes a
subshell, $N local variable is not update outside of
the loop.
Fix this bug by using actual target number (256) instead
of $N.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
