[ Upstream commit d3de41ee5f ]
On PSP v13.x ASICs, boot loader will set only the MSB to 1 and clear the
least significant bits for any command submission. Hence match against
the exact register value, otherwise a register value of all 0xFFs also
could falsely indicate that boot loader is ready. Also, from PSP v13.0.6
and newer, bits[7:0] will be used to indicate command error status.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd64f80587 ]
As &qedi_percpu->p_work_lock is acquired by hard IRQ qedi_msix_handler(),
other acquisitions of the same lock under process context should disable
IRQ, otherwise deadlock could happen if the IRQ preempts the execution
while the lock is held in process context on the same CPU.
qedi_cpu_offline() is one such function which acquires the lock in process
context.
[Deadlock Scenario]
qedi_cpu_offline()
->spin_lock(&p->p_work_lock)
<irq>
->qedi_msix_handler()
->edi_process_completions()
->spin_lock_irqsave(&p->p_work_lock, flags); (deadlock here)
This flaw was found by an experimental static analysis tool I am developing
for IRQ-related deadlocks.
The tentative patch fix the potential deadlock by spin_lock_irqsave()
under process context.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Link: https://lore.kernel.org/r/20230726125655.4197-1-dg573847474@gmail.com
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1e213a9e3 ]
On s390 systems (aka mainframes), it has classic channel devices for
networking and permanent storage that are currently even more common
than PCI devices. Hence it could have a fully functional s390 kernel
with CONFIG_PCI=n, then the relevant iomem mapping functions
[including ioremap(), devm_ioremap(), etc.] are not available.
Here let FSL_EDMA and INTEL_IDMA64 depend on HAS_IOMEM so that it
won't be built to cause below compiling error if PCI is unset.
--------
ERROR: modpost: "devm_platform_ioremap_resource" [drivers/dma/fsl-edma.ko] undefined!
ERROR: modpost: "devm_platform_ioremap_resource" [drivers/dma/idma64.ko] undefined!
--------
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306211329.ticOJCSv-lkp@intel.com/
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Link: https://lore.kernel.org/r/20230707135852.24292-2-bhe@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86582e6189 ]
On a powermac platform, via the call path:
start_kernel()
time_init()
ppc_md.calibrate_decr() (pmac_calibrate_decr)
via_calibrate_decr()
ioremap() and iounmap() are called. The unmap can enable interrupts
unexpectedly (cond_resched() in vunmap_pmd_range()), which causes a
warning later in the boot sequence in start_kernel().
Use the early_* variants of these IO functions to prevent this.
The issue is pre-existing, but is surfaced by commit 721255b982
("genirq: Use a maple tree for interrupt descriptor management").
Signed-off-by: Benjamin Gray <bgray@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230706010816.72682-1-bgray@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16e455a465 ]
Using brcmfmac with 6.5-rc3 on a brcmfmac43241b4-sdio triggers
a backtrace caused by the following field-spanning warning:
memcpy: detected field-spanning write (size 120) of single field
"¶ms_le->channel_list[0]" at
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:1072 (size 2)
The driver still works after this warning. The warning was introduced by the
new field-spanning write checks which were enabled recently.
Fix this by replacing the channel_list[1] declaration at the end of
the struct with a flexible array declaration.
Most users of struct brcmf_scan_params_le calculate the size to alloc
using the size of the non flex-array part of the struct + needed extra
space, so they do not care about sizeof(struct brcmf_scan_params_le).
brcmf_notify_escan_complete() however uses the struct on the stack,
expecting there to be room for at least 1 entry in the channel-list
to store the special -1 abort channel-id.
To make this work use an anonymous union with a padding member
added + the actual channel_list flexible array.
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230729140500.27892-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285975dd67 ]
sk_getsockopt() runs without locks, we must add annotations
to sk->sk_rcvtimeo and sk->sk_sndtimeo.
In the future we might allow fetching these fields before
we lock the socket in TCP fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d7ae22ae9 ]
The commit (SHA1: 5c844d57aa) provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accesses as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9477 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed0cf84e9c ]
It is incorrect in python to compare integer values using the "is" keyword.
The "is" keyword in python is used to compare references to two objects,
not their values. Newer version of python3 (version 3.8) throws a warning
when such incorrect comparison is made. For value comparison, "==" should
be used.
Fix this in the code and suppress the following warning:
/usr/sbin/vmbus_testing:167: SyntaxWarning: "is" with a literal. Did you mean "=="?
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Link: https://lore.kernel.org/r/20230705134408.6302-1-anisinha@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7dd44f4f3 ]
On s390 systems (aka mainframes), it has classic channel devices for
networking and permanent storage that are currently even more common
than PCI devices. Hence it could have a fully functional s390 kernel
with CONFIG_PCI=n, then the relevant iomem mapping functions
[including ioremap(), devm_ioremap(), etc.] are not available.
Here let COMMON_CLK_FIXED_MMIO depend on HAS_IOMEM so that it won't
be built to cause below compiling error if PCI is unset:
------
ld: drivers/clk/clk-fixed-mmio.o: in function `fixed_mmio_clk_setup':
clk-fixed-mmio.c:(.text+0x5e): undefined reference to `of_iomap'
ld: clk-fixed-mmio.c:(.text+0xba): undefined reference to `iounmap'
------
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306211329.ticOJCSv-lkp@intel.com/
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Link: https://lore.kernel.org/r/20230707135852.24292-8-bhe@redhat.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d7f105edb ]
If the current task fails the check for the queried capability via
`capable(CAP_SYS_ADMIN)` LSMs like SELinux generate a denial message.
Issuing such denial messages unnecessarily can lead to a policy author
granting more privileges to a subject than needed to silence them.
Reorder CAP_SYS_ADMIN checks after the check whether the operation is
actually privileged.
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4139f992c4 ]
It is possible for dma_request_chan() to return EPROBE_DEFER, which
means acdev->host->dev is not ready yet. At this point dev_err() will
have no output. Use dev_err_probe() instead.
Signed-off-by: Minjie Du <duminjie@vivo.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18b44bc5a6 ]
Commit db1d1e8b98 ("IMA: use vfs_getattr_nosec to get the i_version")
partially closed an IMA integrity issue when directly modifying a file
on the lower filesystem. If the overlay file is first opened by a user
and later the lower backing file is modified by root, but the extended
attribute is NOT updated, the signature validation succeeds with the old
original signature.
Update the super_block s_iflags to SB_I_IMA_UNVERIFIABLE_SIGNATURE to
force signature reevaluation on every file access until a fine grained
solution can be found.
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a37c55b85 ]
Report current GFX clock also from average clock value as the original
CurrClock data is not valid/accurate any more as per FW team
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21733754c ]
Currently huawei-wmi causes a lot of spam in dmesg on my
Huawei MateBook X Pro 2022:
...
[36409.328463] input input9: Unknown key pressed, code: 0x02c1
[36411.335104] input input9: Unknown key pressed, code: 0x02c1
[36412.338674] input input9: Unknown key pressed, code: 0x02c1
[36414.848564] input input9: Unknown key pressed, code: 0x02c1
[36416.858706] input input9: Unknown key pressed, code: 0x02c1
...
Fix that by ignoring events generated by ambient light sensor.
This issue was reported on GitHub and resolved with the following merge
request:
https://github.com/aymanbagabas/Huawei-WMI/pull/70
I've contacted the mainter of this repo and he gave me the "go ahead" to
send this patch to the maling list.
Signed-off-by: Konstantin Shelekhin <k.shelekhin@ftml.net>
Link: https://lore.kernel.org/r/20230722155922.173856-1-k.shelekhin@ftml.net
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7783e97f85 ]
HP Elite Dragonfly G2 (a convertible laptop/tablet) has a reliable VGBS
method. If VGBS is not called on boot, the firmware sends an initial
0xcd event shortly after calling the BTNL method, but only if the device
is booted in the laptop mode. However, if the device is booted in the
tablet mode and VGBS is not called, there is no initial 0xcc event, and
the input device for SW_TABLET_MODE is not registered up until the user
turns the device into the laptop mode.
Call VGBS on boot on this device to get the initial state of
SW_TABLET_MODE in a reliable way.
Tested with BIOS 1.13.1.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Link: https://lore.kernel.org/r/20230716183213.64173-1-maxtram95@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3ab18de2b ]
On a HP Elite Dragonfly G2 the 0xcc and 0xcd events for SW_TABLET_MODE
are only send after the BTNL ACPI method has been called.
Likely more devices need this, so make the BTNL ACPI method unconditional
instead of only doing it on devices with a 5 button array.
Note this also makes the intel_button_array_enable() call in probe()
unconditional, that function does its own priv->array check. This makes
the intel_button_array_enable() call in probe() consistent with the calls
done on suspend/resume which also rely on the priv->array check inside
the function.
Reported-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/20230712175023.31651-1-maxtram95@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230715181516.5173-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3da4350637 ]
Microsoft Modern Wireless Headset (appearing on the host as "Microsoft
USB Link") has a playback and a capture mixer volume/switch, but they
are fairly broken. The descriptor reports wrong dB ranges for
playback, and the capture volume/switch don't influence on the actual
recording at all. Moreover, there seem instabilities in the
connection, and at best, we should disable the runtime PM.
So this ended up with a quirk entry for:
- Correct the playback dB range;
I picked up some reasonable values but it's a guess work
- Disable the capture mixer;
it's completely useless and confuses PA/PW
- Suppress get-sample-rate, apply the delay for message handling,
and suppress the auto-suspend
The behavior of the wheel control on the headset is somehow flaky,
too, but it's an issue of HID.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1207129
Link: https://lore.kernel.org/r/20230725092057.15115-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1ed39ec11 ]
load_nls() take a char * parameter, use it to find nls module in list or
construct the module name to load it.
This change make load_nls() take a const parameter, so we don't need do
some cast like this:
ses->local_nls = load_nls((char *)ctx->local_nls->charset);
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Winston Wen <wentao@uniontech.com>
Reviewed-by: Paulo Alcantara <pc@manguebit.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a2278ce9c ]
The DASD device driver has a function to requeue requests to the
blocklayer.
This function is used in various cases when basic settings for the device
have to be changed like High Performance Ficon related parameters or copy
pair settings.
The functions iterates over the device->ccw_queue and also removes the
requests from the block->ccw_queue.
In case the device is started on an alias device instead of the base
device it might be removed from the block->ccw_queue without having it
canceled properly before. This might lead to a hanging device since the
request is no longer on a queue and can not be handled properly.
Fix by iterating over the block->ccw_queue instead of the
device->ccw_queue. This will take care of all blocklayer related requests
and handle them on all associated DASD devices.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230721193647.3889634-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acea28a6b7 ]
If a DASD request fails an error recovery procedure (ERP) request might
be built as a copy of the original request to do error recovery.
The ERP request gets a number of retries assigned.
This number is always 256 no matter what other value might have been set
for the original request. This is not what is expected when a user
specifies a certain amount of retries for the device via sysfs.
Correctly use the number of retries of the original request for ERP
requests.
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20230721193647.3889634-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d01da0a1d ]
in atl1c_tso_csum, it should check the return value of pskb_trim(),
and return an error code if an unexpected value is returned
by pskb_trim().
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0691dc162 ]
When handling an AAD interrupt, if IRQ events read failed (for example,
due to i2c "Transfer while suspended" failure, i.e. when attempting to
read it while DA7219 is suspended, which may happen due to a spurious
AAD interrupt), the events array contains garbage uninitialized values.
So instead of trying to interprete those values and doing any actions
based on them (potentially resulting in misbehavior, e.g. reporting
bogus events), refuse to handle the interrupt.
Signed-off-by: Dmytro Maluka <dmy@semihalf.com>
Link: https://lore.kernel.org/r/20230717193737.161784-3-dmy@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91e292917d ]
da7219_aad_suspend() disables jack detection, which should prevent
generating new interrupts by DA7219 while suspended. However, there is a
theoretical possibility that there is a pending interrupt generated just
before suspending DA7219 and not handled yet, so the IRQ handler may
still run after DA7219 is suspended. To prevent that, wait until the
pending IRQ handling is done.
This patch arose as an attempt to fix the following I2C failure
occurring sometimes during system suspend or resume:
[ 355.876211] i2c_designware i2c_designware.3: Transfer while suspended
[ 355.876245] WARNING: CPU: 2 PID: 3576 at drivers/i2c/busses/i2c-designware-master.c:570 i2c_dw_xfer+0x411/0x440
...
[ 355.876462] Call Trace:
[ 355.876468] <TASK>
[ 355.876475] ? update_load_avg+0x1b3/0x615
[ 355.876484] __i2c_transfer+0x101/0x1d8
[ 355.876494] i2c_transfer+0x74/0x10d
[ 355.876504] regmap_i2c_read+0x6a/0x9c
[ 355.876513] _regmap_raw_read+0x179/0x223
[ 355.876521] regmap_raw_read+0x1e1/0x28e
[ 355.876527] regmap_bulk_read+0x17d/0x1ba
[ 355.876532] ? __wake_up+0xed/0x1bb
[ 355.876542] da7219_aad_irq_thread+0x54/0x2c9 [snd_soc_da7219 5fb8ebb2179cf2fea29af090f3145d68ed8e2184]
[ 355.876556] irq_thread+0x13c/0x231
[ 355.876563] ? irq_forced_thread_fn+0x5f/0x5f
[ 355.876570] ? irq_thread_fn+0x4d/0x4d
[ 355.876576] kthread+0x13a/0x152
[ 355.876581] ? synchronize_irq+0xc3/0xc3
[ 355.876587] ? kthread_blkcg+0x31/0x31
[ 355.876592] ret_from_fork+0x1f/0x30
[ 355.876601] </TASK>
which indicates that the AAD IRQ handler is unexpectedly running when
DA7219 is suspended, and as a result, is trying to read data from DA7219
over I2C and is hitting the I2C driver "Transfer while suspended"
failure.
However, with this patch the above failure is still reproducible. So
this patch does not fix any real observed issue so far, but at least is
useful for confirming that the above issue is not caused by a pending
IRQ but rather looks like a DA7219 hardware issue with an IRQ
unexpectedly generated after jack detection is already disabled.
Signed-off-by: Dmytro Maluka <dmy@semihalf.com>
Link: https://lore.kernel.org/r/20230717193737.161784-2-dmy@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 536bb492d3 ]
If client send smb2 negotiate request and then send smb1 negotiate
request, init_smb2_rsp_hdr is called for smb1 negotiate request since
need_neg is set to false. This patch ignore smb1 packets after ->need_neg
is set to false.
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21541
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e202a1e863 ]
ksmbd doesn't support compound read. If client send read-read in
compound to ksmbd, there can be memory leak from read buffer.
Windows and linux clients doesn't send it to server yet. For now,
No response from compound read. compound read will be supported soon.
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21587, ZDI-CAN-21588
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3df0411e13 ]
`smb2_get_msg()` in smb2_get_ksmbd_tcon() and smb2_check_user_session()
will always return the first request smb2 header in a compound request.
if `SMB2_TREE_CONNECT_HE` is the first command in compound request, will
return 0, i.e. The tree id check is skipped.
This patch use ksmbd_req_buf_next() to get current command in compound.
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21506
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a73edab69 ]
Similarly to the previous patch: offs can be used in handle_rerrors
without initializing on small payloads; in this case handle_rerrors will
not use it because of the size check, but it doesn't hurt to make sure
it is zero to please scan-build.
This fixes the following warning:
net/9p/trans_virtio.c:539:3: warning: 3rd function call argument is an uninitialized value [core.CallAndMessage]
handle_rerror(req, in_hdr_len, offs, in_pages);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13ade4ac5c ]
handle_rerror can dereference the pages pointer, but it is not
necessarily set for small payloads.
In practice these should be filtered out by the size check, but
might as well double-check explicitly.
This fixes the following scan-build warnings:
net/9p/trans_virtio.c:401:24: warning: Dereference of null pointer [core.NullDereference]
memcpy_from_page(to, *pages++, offs, n);
^~~~~~~~
net/9p/trans_virtio.c:406:23: warning: Dereference of null pointer (loaded from variable 'pages') [core.NullDereference]
memcpy_from_page(to, *pages, offs, size);
^~~~~~
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
