commit 9aa422ad32 upstream.
The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.
This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.
tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16. To
avert any risk of bit overflow, we add an extra sanity check for this in
that function. We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer. This potential problem was identified by Eric Dumazet.
This fixes CVE-2022-0435
Reported-by: Samuel Page <samuel.page@appgate.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 35c55c9877 ("tipc: add neighbor monitoring framework")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Samuel Page <samuel.page@appgate.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24f6008564 upstream.
The cgroup release_agent is called with call_usermodehelper. The function
call_usermodehelper starts the release_agent with a full set fo capabilities.
Therefore require capabilities when setting the release_agaent.
Reported-by: Tabitha Sable <tabitha.c.sable@gmail.com>
Tested-by: Tabitha Sable <tabitha.c.sable@gmail.com>
Fixes: 81a6a5cdd2 ("Task Control Groups: automatic userspace notification of idle cgroups")
Cc: stable@vger.kernel.org # v2.6.24+
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
[mkoutny: Adjust for pre-fs_context, duplicate mount/remount check, drop log messages.]
Acked-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 897026aaa7 upstream.
While running "./check -I 200 generic/475" it sometimes gives below
kernel BUG(). Ideally we should not call ext4_write_inline_data() if
ext4_create_inline_data() has failed.
<log snip>
[73131.453234] kernel BUG at fs/ext4/inline.c:223!
<code snip>
212 static void ext4_write_inline_data(struct inode *inode, struct ext4_iloc *iloc,
213 void *buffer, loff_t pos, unsigned int len)
214 {
<...>
223 BUG_ON(!EXT4_I(inode)->i_inline_off);
224 BUG_ON(pos + len > EXT4_I(inode)->i_inline_size);
This patch handles the error and prints out a emergency msg saying potential
data loss for the given inode (since we couldn't restore the original
inline_data due to some previous error).
[ 9571.070313] EXT4-fs (dm-0): error restoring inline_data for inode -- potential data loss! (inode 1703982, error -30)
Reported-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/9f4cd7dfd54fa58ff27270881823d94ddf78dd07.1642416995.git.riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dfd0dfb9a7 upstream.
The driver overrides error codes returned by platform_get_irq_optional()
to -EINVAL for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
[ bp: Massage commit message. ]
Fixes: 0d4429301c ("EDAC: Add APM X-Gene SoC EDAC driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220124185503.6720-3-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 279eb8575f upstream.
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
[ bp: Massage commit message. ]
Fixes: 71bcada88b ("edac: altera: Add Altera SDRAM EDAC support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220124185503.6720-2-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab451ea952 upstream.
From RFC 7530 Section 16.34.5:
o The server has not recorded an unconfirmed { v, x, c, *, * } and
has recorded a confirmed { v, x, c, *, s }. If the principals of
the record and of SETCLIENTID_CONFIRM do not match, the server
returns NFS4ERR_CLID_INUSE without removing any relevant leased
client state, and without changing recorded callback and
callback_ident values for client { x }.
The current code intends to do what the spec describes above but
it forgot to set 'old' to NULL resulting to the confirmed client
to be expired.
Fixes: 2b63482185 ("nfsd: fix clid_inuse on mount with security change")
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0cfa548db upstream.
When setting Tx sci explicit, the Rx side is expected to use this
sci and not recalculate it from the packet.However, in case of Tx sci
is explicit and send_sci is off, the receiver is wrongly recalculate
the sci from the source MAC address which most likely be different
than the explicit sci.
Fix by preventing such configuration when macsec newlink is established
and return EINVAL error code on such cases.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Link: https://lore.kernel.org/r/1643542672-29403-1-git-send-email-raeds@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cbd27267f upstream.
Apply only valid chip select value. This change fixes case where chip
select is set to initial value of '-1' during probe and PM supend and
subsequent resume can try to use the value with undefined behaviour.
Also in case where gpio based chip select, the check in
bcm_qspi_chip_select() shall prevent undefined behaviour on resume.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220127185359.27322-1-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b45a7738e upstream.
The polling loop for the register change in iommu_ga_log_enable() needs
to have a udelay() in it. Otherwise the CPU might be faster than the
IOMMU hardware and wrongly trigger the WARN_ON() further down the code
stream. Use a 10us for udelay(), has there is some hardware where
activation of the GA log can take more than a 100ms.
A future optimization should move the activation check of the GA log
to the point where it gets used for the first time. But that is a
bigger change and not suitable for a fix.
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20220204115537.3894-1-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b777d4d9e upstream.
Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.
This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.
Signed-off-by: Nick Lopez <github@glowingmonkey.org>
Fixes: 4d4e9907ff ("drm/nouveau/bios: guard against out-of-bounds accesses to image")
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e42e70ad6a upstream.
When packet_setsockopt( PACKET_FANOUT_DATA ) reads po->fanout,
no lock is held, meaning that another thread can change po->fanout.
Given that po->fanout can only be set once during the socket lifetime
(it is only cleared from fanout_release()), we can use
READ_ONCE()/WRITE_ONCE() to document the race.
BUG: KCSAN: data-race in packet_setsockopt / packet_setsockopt
write to 0xffff88813ae8e300 of 8 bytes by task 14653 on cpu 0:
fanout_add net/packet/af_packet.c:1791 [inline]
packet_setsockopt+0x22fe/0x24a0 net/packet/af_packet.c:3931
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88813ae8e300 of 8 bytes by task 14654 on cpu 1:
packet_setsockopt+0x691/0x24a0 net/packet/af_packet.c:3935
__sys_setsockopt+0x209/0x2a0 net/socket.c:2180
__do_sys_setsockopt net/socket.c:2191 [inline]
__se_sys_setsockopt net/socket.c:2188 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2188
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000000000000000 -> 0xffff888106f8c000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 14654 Comm: syz-executor.3 Not tainted 5.16.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 47dceb8ecd ("packet: add classic BPF fanout mode")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220201022358.330621-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a504b703bb upstream.
In case almost or all available ports are taken, clash resolution can
take a very long time, resulting in soft lockup.
This can happen when many to-be-natted hosts connect to same
destination:port (e.g. a proxy) and all connections pass the same SNAT.
Pick a random offset in the acceptable range, then try ever smaller
number of adjacent port numbers, until either the limit is reached or a
useable port was found. This results in at most 248 attempts
(128 + 64 + 32 + 16 + 8, i.e. 4 restarts with new search offset)
instead of 64000+,
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ed5943f87 upstream.
This is a leftover from days where single-cpu systems were common:
Store last port used to resolve a clash to use it as a starting point when
the next conflict needs to be resolved.
When we have parallel attempt to connect to same address:port pair,
its likely that both cores end up computing the same "available" port,
as both use same starting port, and newly used ports won't become
visible to other cores until the conntrack gets confirmed later.
One of the cores then has to drop the packet at insertion time because
the chosen new tuple turns out to be in use after all.
Lets simplify this: remove port rover and use a pseudo-random starting
point.
Note that this doesn't make netfilter default to 'fully random' mode;
the 'rover' was only used if NAT could not reuse source port as-is.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 970a5a3ea8 ]
In commit 431280eebe ("ipv4: tcp: send zero IPID for RST and
ACK sent in SYN-RECV and TIME-WAIT state") we took care of some
ctl packets sent by TCP.
It turns out we need to use a similar strategy for SYNACK packets.
By default, they carry IP_DF and IPID==0, but there are ways
to ask them to use the hashed IP ident generator and thus
be used to build off-path attacks.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
One of this way is to force (before listener is started)
echo 1 >/proc/sys/net/ipv4/ip_no_pmtu_disc
Another way is using forged ICMP ICMP_FRAG_NEEDED
with a very small MTU (like 68) to force a false return from
ip_dont_fragment()
In this patch, ip_build_and_send_pkt() uses the following
heuristics.
1) Most SYNACK packets are smaller than IPV4_MIN_MTU and therefore
can use IP_DF regardless of the listener or route pmtu setting.
2) In case the SYNACK packet is bigger than IPV4_MIN_MTU,
we use prandom_u32() generator instead of the IPv4 hashed ident one.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ray Che <xijiache@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Cc: Geoff Alexander <alexandg@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a66c5ed539 ]
According to its datasheet, G781 supports a maximum conversion rate value
of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only
support a maximum conversion rate value of 7 (125 ms). On the other side,
chips labeled G781-1 and G784 were found to support a conversion rate value
of 8. There is no known means to distinguish G780 from G781 or G784; all
chips report the same manufacturer ID and chip revision.
Setting the conversion rate register value to 8 on chips not supporting
it causes unexpected behavior since the real conversion rate is set to 0
(16 seconds) if a value of 8 is written into the conversion rate register.
Limit the conversion rate register value to 7 for all G78x chips to avoid
the problem.
Fixes: ae544f64cc ("hwmon: (lm90) Add support for GMT G781")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d10f8a1f4 upstream.
After commit:7866a621043f ("dev: add per net_device packet type chains"),
we can not get packet types that are bound to a specified net device by
/proc/net/ptype, this patch fix the regression.
Run "tcpdump -i ens192 udp -nns0" Before and after apply this patch:
Before:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
After:
[root@localhost ~]# cat /proc/net/ptype
Type Device Function
ALL ens192 tpacket_rcv
0800 ip_rcv
0806 arp_rcv
86dd ipv6_rcv
v1 -> v2:
- fix the regression rather than adding new /proc API as
suggested by Stephen Hemminger.
Fixes: 7866a62104 ("dev: add per net_device packet type chains")
Signed-off-by: Jianguo Wu <wujianguo@chinatelecom.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1751fc1db3 upstream.
If the file type changes back to being a regular file on the server
between the failed OPEN and our LOOKUP, then we need to re-run the OPEN.
Fixes: 0dd2b474d0 ("nfs: implement i_op->atomic_open()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac795161c9 upstream.
If the application sets the O_DIRECTORY flag, and tries to open a
regular file, nfs_atomic_open() will punt to doing a regular lookup.
If the server then returns a regular file, we will happily return a
file descriptor with uninitialised open state.
The fix is to return the expected ENOTDIR error in these cases.
Reported-by: Lyu Tao <tao.lyu@epfl.ch>
Fixes: 0dd2b474d0 ("nfs: implement i_op->atomic_open()")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23f57406b8 upstream.
ip_select_ident_segs() has been very conservative about using
the connected socket private generator only for packets with IP_DF
set, claiming it was needed for some VJ compression implementations.
As mentioned in this referenced document, this can be abused.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)
Before switching to pure random IPID generation and possibly hurt
some workloads, lets use the private inet socket generator.
Not only this will remove one vulnerability, this will also
improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT
Fixes: 73f156a6e8 ("inetpeer: get rid of ip_id_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reported-by: Ray Che <xijiache@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47934e06b6 upstream.
In one net namespace, after creating a packet socket without binding
it to a device, users in other net namespaces can observe the new
`packet_type` added by this packet socket by reading `/proc/net/ptype`
file. This is minor information leakage as packet socket is
namespace aware.
Add a net pointer in `packet_type` to keep the net namespace of
of corresponding packet socket. In `ptype_seq_show`, this net pointer
must be checked when it is not NULL.
Fixes: 2feb27dbe0 ("[NETNS]: Minor information leak via /proc/net/ptype file.")
Signed-off-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6cee105e7f upstream.
The warning messages can be invoked from the data path for every packet
transmitted through an ip6gre netdev, leading to high CPU utilization.
Fix that by rate limiting the messages.
Fixes: 09c6bbf090 ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26fbe9772b upstream.
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b67b31503 upstream.
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8838b2af23 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9d967b2ce upstream.
The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct. Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fc3b7c298 upstream.
udf_expand_file_adinicb() calls directly ->writepage to write data
expanded into a page. This however misses to setup inode for writeback
properly and so we can crash on inode->i_wb dereference when submitting
page for IO like:
BUG: kernel NULL pointer dereference, address: 0000000000000158
#PF: supervisor read access in kernel mode
...
<TASK>
__folio_start_writeback+0x2ac/0x350
__block_write_full_page+0x37d/0x490
udf_expand_file_adinicb+0x255/0x400 [udf]
udf_file_write_iter+0xbe/0x1b0 [udf]
new_sync_write+0x125/0x1c0
vfs_write+0x28e/0x400
Fix the problem by marking the page dirty and going through the standard
writeback path to write the page. Strictly speaking we would not even
have to write the page but we want to catch e.g. ENOSPC errors early.
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 52ebea749a ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
