[ Upstream commit 2ad52bdb22 ]
Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bcb959d05 ]
During load balance, LBF_SOME_PINNED will be set if any candidate task
cannot be detached due to CPU affinity constraints. This can result in
setting env->sd->parent->sgc->group_imbalance, which can lead to a group
being classified as group_imbalanced (rather than any of the other, lower
group_type) when balancing at a higher level.
In workloads involving a single task per CPU, LBF_SOME_PINNED can often be
set due to per-CPU kthreads being the only other runnable tasks on any
given rq. This results in changing the group classification during
load-balance at higher levels when in reality there is nothing that can be
done for this affinity constraint: per-CPU kthreads, as the name implies,
don't get to move around (modulo hotplug shenanigans).
It's not as clear for userspace tasks - a task could be in an N-CPU cpuset
with N-1 offline CPUs, making it an "accidental" per-CPU task rather than
an intended one. KTHREAD_IS_PER_CPU gives us an indisputable signal which
we can leverage here to not set LBF_SOME_PINNED.
Note that the aforementioned classification to group_imbalance (when
nothing can be done) is especially problematic on big.LITTLE systems, which
have a topology the likes of:
DIE [ ]
MC [ ][ ]
0 1 2 3
L L B B
arch_scale_cpu_capacity(L) < arch_scale_cpu_capacity(B)
Here, setting LBF_SOME_PINNED due to a per-CPU kthread when balancing at MC
level on CPUs [0-1] will subsequently prevent CPUs [2-3] from classifying
the [0-1] group as group_misfit_task when balancing at DIE level. Thus, if
CPUs [0-1] are running CPU-bound (misfit) tasks, ill-timed per-CPU kthreads
can significantly delay the upgmigration of said misfit tasks. Systems
relying on ASYM_PACKING are likely to face similar issues.
Signed-off-by: Lingutla Chandrasekhar <clingutla@codeaurora.org>
[Use kthread_is_per_cpu() rather than p->nr_cpus_allowed]
[Reword changelog]
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lkml.kernel.org/r/20210407220628.3798191-2-valentin.schneider@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f4e6644cd ]
For two of the supported sensors the stv06xx driver allocates memory which
is stored in sd->sensor_priv. This memory is freed on a disconnect, but if
the probe() fails, then it isn't freed and so this leaks memory.
Add a new probe_error() op that drivers can use to free any allocated
memory in case there was a probe failure.
Thanks to Pavel Skripkin <paskripkin@gmail.com> for discovering the cause
of the memory leak.
Reported-and-tested-by: syzbot+e7f4c64a4248a0340c37@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7cd0da982 ]
syzbot reported memory leak in dvb-usb. The problem was
in invalid error handling in dvb_usb_adapter_init().
for (n = 0; n < d->props.num_adapters; n++) {
....
if ((ret = dvb_usb_adapter_stream_init(adap)) ||
(ret = dvb_usb_adapter_dvb_init(adap, adapter_nrs)) ||
(ret = dvb_usb_adapter_frontend_init(adap))) {
return ret;
}
...
d->num_adapters_initialized++;
...
}
In case of error in dvb_usb_adapter_dvb_init() or
dvb_usb_adapter_dvb_init() d->num_adapters_initialized won't be
incremented, but dvb_usb_adapter_exit() relies on it:
for (n = 0; n < d->num_adapters_initialized; n++)
So, allocated objects won't be freed.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reported-by: syzbot+3c2be7424cea3b932b0e@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1995d5e43 ]
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69306a947b ]
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a15275b6a ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f820ab5d4 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9541720c ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa56f5f1fe ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6107a4fdf8 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68ae256945 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6cfa007b3 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 443ec4bbc6 ]
The EDID had a few mistakes as reported by edid-decode:
Block 1, CTA-861 Extension Block:
Video Data Block: For improved preferred timing interoperability, set 'Native detailed modes' to 1.
Video Capability Data Block: S_PT is equal to S_IT and S_CE, so should be set to 0 instead.
Fixed those.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ae10a7dc8 ]
If some error occurs, URB buffers should also be freed. If they aren't
freed with the dvb here, the em28xx_dvb_fini call doesn't frees the URB
buffers as dvb is set to NULL. The function in which error occurs should
do all the cleanup for the allocations it had done.
Tested the patch with the reproducer provided by syzbot. This patch
fixes the memleak.
Reported-by: syzbot+889397c820fa56adf25d@syzkaller.appspotmail.com
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 751faedf06 ]
Adds 80000 us sleep when the usb cable is plugged in to hopefully avoid
bouncing contacts.
Upon pluging in the usb cable vbus will bounce for some time, causing cpcap to
dissconnect charging due to detecting an undervoltage condition. This is a
scope of vbus on xt894 while quickly inserting the usb cable with firm force,
probed at the far side of the usb socket and vbus loaded with approx 1k:
http://uvos.xyz/maserati/usbplug.jpg.
As can clearly be seen, vbus is all over the place for the first 15 ms or so
with a small blip at ~40 ms this causes the cpcap to trip up and disable
charging again.
The delay helps cpcap_usb_detect avoid the worst of this. It is, however, still
not ideal as strong vibrations can cause the issue to reapear any time during
charging. I have however not been able to cause the device to stop charging due
to this in practice as it is hard to vibrate the device such that the vbus pins
start bouncing again but cpcap_usb_detect is not called again due to a detected
disconnect/reconnect event.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1205b688c9 ]
Dan reported following static checker warnings
tools/testing/selftests/resctrl/resctrl_val.c:545 measure_vals()
warn: 'bw_imc' unsigned <= 0
tools/testing/selftests/resctrl/resctrl_val.c:549 measure_vals()
warn: 'bw_resc_end' unsigned <= 0
These warnings are reported because
1. measure_vals() declares 'bw_imc' and 'bw_resc_end' as unsigned long
variables
2. Return value of get_mem_bw_imc() and get_mem_bw_resctrl() are assigned
to 'bw_imc' and 'bw_resc_end' respectively
3. The returned values are checked for <= 0 to see if the calls failed
Checking for < 0 for an unsigned value doesn't make any sense.
Fix this issue by changing the implementation of get_mem_bw_imc() and
get_mem_bw_resctrl() such that they now accept reference to a variable
and set the variable appropriately upon success and return 0, else return
< 0 on error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d81343b5ee ]
iMC (Integrated Memory Controller) counters are usually at
"/sys/bus/event_source/devices/" and are named as "uncore_imc_<n>".
num_of_imcs() function tries to count number of such iMC counters so that
it could appropriately initialize required number of perf_attr structures
that could be used to read these iMC counters.
num_of_imcs() function assumes that all the directories under this path
that start with "uncore_imc" are iMC counters. But, on some systems there
could be directories named as "uncore_imc_free_running" which aren't iMC
counters. Trying to read from such directories will result in "not found
file" errors and MBM/MBA tests will fail.
Hence, fix the logic in num_of_imcs() such that it looks at the first
character after "uncore_imc_" to check if it's a numerical digit or not. If
it's a digit then the directory represents an iMC counter, else, skip the
directory.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0415681e ]
Resctrl test suite before running any unit test (like cmt, cat, mbm and
mba) should first check if the feature is enabled (by kernel and not just
supported by H/W) on the platform or not.
validate_resctrl_feature_request() is supposed to do that. This function
intends to grep for relevant flags in /proc/cpuinfo but there are several
issues here
1. validate_resctrl_feature_request() calls fgrep() to get flags from
/proc/cpuinfo. But, fgrep() can only return a string with maximum of 255
characters and hence the complete cpu flags are never returned.
2. The substring search logic is also busted. If strstr() finds requested
resctrl feature in the cpu flags, it returns pointer to the first
occurrence. But, the logic negates the return value of strstr() and
hence validate_resctrl_feature_request() returns false if the feature is
present in the cpu flags and returns true if the feature is not present.
3. validate_resctrl_feature_request() checks if a resctrl feature is
reported in /proc/cpuinfo flags or not. Having a cpu flag means that the
H/W supports the feature, but it doesn't mean that the kernel enabled
it. A user could selectively enable only a subset of resctrl features
using kernel command line arguments. Hence, /proc/cpuinfo isn't a
reliable source to check if a feature is enabled or not.
The 3rd issue being the major one and fixing it requires changing the way
validate_resctrl_feature_request() works. Since, /proc/cpuinfo isn't the
right place to check if a resctrl feature is enabled or not, a more
appropriate place is /sys/fs/resctrl/info directory. Change
validate_resctrl_feature_request() such that,
1. For cat, check if /sys/fs/resctrl/info/L3 directory is present or not
2. For mba, check if /sys/fs/resctrl/info/MB directory is present or not
3. For cmt, check if /sys/fs/resctrl/info/L3_MON directory is present and
check if /sys/fs/resctrl/info/L3_MON/mon_features has llc_occupancy
4. For mbm, check if /sys/fs/resctrl/info/L3_MON directory is present and
check if /sys/fs/resctrl/info/L3_MON/mon_features has
mbm_<total/local>_bytes
Please note that only L3_CAT, L3_CMT, MBA and MBM are supported. CDP and L2
variants can be added later.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7af3d0d51 ]
resctrl test suite accepts command line arguments (like -b, -t, -n and -p)
as documented in the help. But passing -n and -p throws an invalid option
error. This happens because -n and -p are missing in the list of
characters that getopt() recognizes as valid arguments. Hence, they are
treated as invalid options.
Fix this by adding them to the list of characters that getopt() recognizes
as valid arguments. Please note that the main() function already has the
logic to deal with the values passed as part of these arguments and hence
no changes are needed there.
Tested-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 896016d2ad ]
Reinette reported following compilation issue on Fedora 32, gcc version
10.1.1
/usr/bin/ld: resctrl_tests.o:<src_dir>/resctrl.h:65: multiple definition
of `bm_pid'; cache.o:<src_dir>/resctrl.h:65: first defined here
Other variables are ppid, tests_run, llc_occup_path, is_amd. Compiler
isn't happy because these variables are defined globally in two .c files
but are not declared as extern.
To fix issues for the global variables, declare them as extern.
Chang Log:
- Split this patch from v4's patch 1 (Shuah).
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8236c51d85 ]
Reinette reported following compilation issue on Fedora 32, gcc version
10.1.1
/usr/bin/ld: cqm_test.o:<src_dir>/cqm_test.c:22: multiple definition of
`cache_size'; cat_test.o:<src_dir>/cat_test.c:23: first defined here
The same issue is reported for long_mask, cbm_mask, count_of_bits etc
variables as well. Compiler isn't happy because these variables are
defined globally in two .c files namely cqm_test.c and cat_test.c and
the compiler during compilation finds that the variable is already
defined (multiple definition error).
Taking a closer look at the usage of these variables reveals that these
variables are used only locally in functions such as cqm_resctrl_val()
(defined in cqm_test.c) and cat_perf_miss_val() (defined in cat_test.c).
These variables are not shared between those functions. So, there is no
need for these variables to be global. Hence, fix this issue by making
them static variables.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9d26a302d ]
David reported a buffer overflow error in the check_results() function of
the cmt unit test and he suggested enabling _FORTIFY_SOURCE gcc compiler
option to automatically detect any such errors.
Feature Test Macros man page describes_FORTIFY_SOURCE as below
"Defining this macro causes some lightweight checks to be performed to
detect some buffer overflow errors when employing various string and memory
manipulation functions (for example, memcpy, memset, stpcpy, strcpy,
strncpy, strcat, strncat, sprintf, snprintf, vsprintf, vsnprintf, gets, and
wide character variants thereof). For some functions, argument consistency
is checked; for example, a check is made that open has been supplied with a
mode argument when the specified flags include O_CREAT. Not all problems
are detected, just some common cases.
If _FORTIFY_SOURCE is set to 1, with compiler optimization level 1 (gcc
-O1) and above, checks that shouldn't change the behavior of conforming
programs are performed.
With _FORTIFY_SOURCE set to 2, some more checking is added, but some
conforming programs might fail.
Some of the checks can be performed at compile time (via macros logic
implemented in header files), and result in compiler warnings; other checks
take place at run time, and result in a run-time error if the check fails.
Use of this macro requires compiler support, available with gcc since
version 4.0."
Fix the buffer overflow error in the check_results() function of the cmt
unit test and enable _FORTIFY_SOURCE gcc check to catch any future buffer
overflow errors.
Reported-by: David Binderman <dcb314@hotmail.com>
Suggested-by: David Binderman <dcb314@hotmail.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79695dcd9a ]
Return NVME_SC_INVALID_FIELD from discovery controller like normal
controller when executing identify or get log page command.
Signed-off-by: Hou Pu <houpu.main@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 234e6d2c18 ]
On Hisilicon Kunpeng920, ESP is set to 1 by default for all ports of
SATA controller. In some scenarios, some ports are not external SATA ports,
and it cause disks connected to these ports to be identified as removable
disks. So disable the SXS capability on the software side to prevent users
from mistakenly considering non-removable disks as removable disks and
performing related operations.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1615544676-61926-1-git-send-email-luojiaxing@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4710430a77 ]
[Why]
When unplugging a display, the underflow counter can be seen to
increase because PSTATE switch is allowed even when some planes are not
blanked.
[How]
Check that all planes are not active instead of all streams before
allowing PSTATE change.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8941550aa ]
This recent change introduce SDMA interrupt info printing with irq->process function.
These functions do not require a set function to enable/disable the irq
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ac5617c4b ]
The psp supplies the link type in the upper 2 bits of the psp xgmi node
information num_hops field. With a new link type, Aldebaran has these
bits set to a non-zero value (1 = xGMI3) so the KFD topology will report
the incorrect IO link weights without proper masking.
The actual number of hops is located in the 3 least significant bits of
this field so mask if off accordingly before passing it to the KFD.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Amber Lin <amber.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d6e9cdff7 ]
Currently, for WLED5, the FSC (Full scale current) setting is not
updated properly due to driver toggling the wrong register after
an FSC update.
On WLED5 we should only toggle the MOD_SYNC bit after a brightness
update. For an FSC update we need to toggle the SYNC bits instead.
Fix it by adopting the common wled3_sync_toggle() for WLED5 and
introducing new code to the brightness update path to compensate.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdfd4c689e ]
WLED3_SINK_REG_SYNC is, as the name implies, a sink register offset.
Therefore, use the sink address as base instead of the ctrl address.
This fixes the sync toggle on wled4, which can be observed by the fact
that adjusting brightness now works.
It has no effect on wled3 because sink and ctrl base addresses are the
same. This allows adjusting the brightness without having to disable
then reenable the module.
Signed-off-by: Obeida Shamoun <oshmoun100@googlemail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
