[ Upstream commit ac28b1ec61 ]
I got the below warning when do fuzzing test:
unregister_netdevice: waiting for bond0 to become free. Usage count = 2
It can be repoduced via:
ip link add bond0 type bond
sysctl -w net.ipv4.conf.bond0.promote_secondaries=1
ip addr add 4.117.174.103/0 scope 0x40 dev bond0
ip addr add 192.168.100.111/255.255.255.254 scope 0 dev bond0
ip addr add 0.0.0.4/0 scope 0x40 secondary dev bond0
ip addr del 4.117.174.103/0 scope 0x40 dev bond0
ip link delete bond0 type bond
In this reproduction test case, an incorrect 'last_prim' is found in
__inet_del_ifa(), as a result, the secondary address(0.0.0.4/0 scope 0x40)
is lost. The memory of the secondary address is leaked and the reference of
in_device and net_device is leaked.
Fix this problem:
Look for 'last_prim' starting at location of the deleted IP and inserting
the promoted IP into the location of 'last_prim'.
Fixes: 0ff60a4567 ("[IPV4]: Fix secondary IP addresses after promotion")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d0b65569c ]
Fix race condition between Interrupt thread and Chip reset thread in trying
to flush the same mailbox. With the race condition, the "ha->mbx_intr_comp"
will get an extra complete() call. The extra complete call create erroneous
mailbox timeout condition when the next mailbox is sent where the mailbox
call does not wait for interrupt to arrive. Instead, it advances without
waiting.
Add lock protection around the check for mailbox completion.
Cc: stable@vger.kernel.org
Fixes: b2000805a9 ("scsi: qla2xxx: Flush mailbox commands on chip reset")
Signed-off-by: Quinn Tran <quinn.tran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230821130045.34850-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cd474e573 ]
Interrupts are blocked in SDEI context, per the SDEI spec: "The client
interrupts cannot preempt the event handler." If we crashed in the SDEI
handler-running context (as with ACPI's AGDI) then we need to clean up the
SDEI state before proceeding to the crash kernel so that the crash kernel
can have working interrupts.
Track the active SDEI handler per-cpu so that we can COMPLETE_AND_RESUME
the handler, discarding the interrupted context.
Fixes: f5df269618 ("arm64: kernel: Add arch-specific SDEI entry code and CPU masking")
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Cc: stable@vger.kernel.org
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: Mihai Carabas <mihai.carabas@oracle.com>
Link: https://lore.kernel.org/r/20230627002939.2758-1-scott@os.amperecomputing.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc4e8c07e9 ]
From commit e147133a42 ("ACPI / APEI: Make hest.c manage the estatus
memory pool") was merged, ghes_init() relies on acpi_hest_init() to manage
the estatus memory pool. On the other hand, ghes_init() relies on
sdei_init() to detect the SDEI version and (un)register events. The
dependencies are as follows:
ghes_init() => acpi_hest_init() => acpi_bus_init() => acpi_init()
ghes_init() => sdei_init()
HEST is not PCI-specific and initcall ordering is implicit and not
well-defined within a level.
Based on above, remove acpi_hest_init() from acpi_pci_root_init() and
convert ghes_init() and sdei_init() from initcalls to explicit calls in the
following order:
acpi_hest_init()
ghes_init()
sdei_init()
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 5cd474e573 ("arm64: sdei: abort running SDEI handlers during crash")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f6b8436bed upstream.
The 'e' key is to toggle expand/collapse the selected entry only. But
the current code has a bug that it only increases the number of entries
by 1 in the hierarchy mode so users cannot move under the current entry
after the key stroke. This is due to a wrong assumption in the
hist_entry__set_folding().
The commit b33f922651 ("perf hists browser: Put hist_entry folding
logic into single function") factored out the code, but actually it
should be handled separately. The hist_browser__set_folding() is to
update fold state for each entry so it needs to traverse all (child)
entries regardless of the current fold state. So it increases the
number of entries by 1.
But the hist_entry__set_folding() only cares the currently selected
entry and its all children. So it should count all unfolded child
entries. This code is implemented in hist_browser__toggle_fold()
already so we can just call it.
Fixes: b33f922651 ("perf hists browser: Put hist_entry folding logic into single function")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230731094934.1616495-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bf63282ea upstream.
The PERF_RECORD_ATTR is used for a pipe mode to describe an event with
attribute and IDs. The ID table comes after the attr and it calculate
size of the table using the total record size and the attr size.
n_ids = (total_record_size - end_of_the_attr_field) / sizeof(u64)
This is fine for most use cases, but sometimes it saves the pipe output
in a file and then process it later. And it becomes a problem if there
is a change in attr size between the record and report.
$ perf record -o- > perf-pipe.data # old version
$ perf report -i- < perf-pipe.data # new version
For example, if the attr size is 128 and it has 4 IDs, then it would
save them in 168 byte like below:
8 byte: perf event header { .type = PERF_RECORD_ATTR, .size = 168 },
128 byte: perf event attr { .size = 128, ... },
32 byte: event IDs [] = { 1234, 1235, 1236, 1237 },
But when report later, it thinks the attr size is 136 then it only read
the last 3 entries as ID.
8 byte: perf event header { .type = PERF_RECORD_ATTR, .size = 168 },
136 byte: perf event attr { .size = 136, ... },
24 byte: event IDs [] = { 1235, 1236, 1237 }, // 1234 is missing
So it should use the recorded version of the attr. The attr has the
size field already then it should honor the size when reading data.
Fixes: 2c46dbb517 ("perf: Convert perf header attrs into attr events")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230825152552.112913-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d167aa76dc upstream.
The function btrfs_validate_super() should verify the fsid in the provided
superblock argument. Because, all its callers expect it to do that.
Such as in the following stack:
write_all_supers()
sb = fs_info->super_for_commit;
btrfs_validate_write_super(.., sb)
btrfs_validate_super(.., sb, ..)
scrub_one_super()
btrfs_validate_super(.., sb, ..)
And
check_dev_super()
btrfs_validate_super(.., sb, ..)
However, it currently verifies the fs_info::super_copy::fsid instead,
which is not correct. Fix this using the correct fsid in the superblock
argument.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4490e803e1 upstream.
When joining a transaction with TRANS_JOIN_NOSTART, if we don't find a
running transaction we end up creating one. This goes against the purpose
of TRANS_JOIN_NOSTART which is to join a running transaction if its state
is at or below the state TRANS_STATE_COMMIT_START, otherwise return an
-ENOENT error and don't start a new transaction. So fix this to not create
a new transaction if there's no running transaction at or below that
state.
CC: stable@vger.kernel.org # 4.14+
Fixes: a6d155d2e3 ("Btrfs: fix deadlock between fiemap and transaction commits")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8bd342d50 upstream.
During our debugging of glusterfs, we found an Assertion failed error:
inode_lookup >= nlookup, which was caused by the nlookup value in the
kernel being greater than that in the FUSE file system.
The issue was introduced by fuse_direntplus_link, where in the function,
fuse_iget increments nlookup, and if d_splice_alias returns failure,
fuse_direntplus_link returns failure without decrementing nlookup
https://github.com/gluster/glusterfs/pull/4081
Signed-off-by: ruanmeisi <ruan.meisi@zte.com.cn>
Fixes: 0b05b18381 ("fuse: implement NFS-like readdirplus support")
Cc: <stable@vger.kernel.org> # v3.9
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 674d9591a3 ]
When sfp is absent or unidentified, the port type should be
displayed as PORT_OTHERS, rather than PORT_FIBRE.
Fixes: 88d10bd6f7 ("net: hns3: add support for multiple media type")
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4f8a78031 ]
The opt_num field is controlled by user mode and is not currently
validated inside the kernel. An attacker can take advantage of this to
trigger an OOB read and potentially leak information.
BUG: KASAN: slab-out-of-bounds in nf_osf_match_one+0xbed/0xd10 net/netfilter/nfnetlink_osf.c:88
Read of size 2 at addr ffff88804bc64272 by task poc/6431
CPU: 1 PID: 6431 Comm: poc Not tainted 6.0.0-rc4 #1
Call Trace:
nf_osf_match_one+0xbed/0xd10 net/netfilter/nfnetlink_osf.c:88
nf_osf_find+0x186/0x2f0 net/netfilter/nfnetlink_osf.c:281
nft_osf_eval+0x37f/0x590 net/netfilter/nft_osf.c:47
expr_call_ops_eval net/netfilter/nf_tables_core.c:214
nft_do_chain+0x2b0/0x1490 net/netfilter/nf_tables_core.c:264
nft_do_chain_ipv4+0x17c/0x1f0 net/netfilter/nft_chain_filter.c:23
[..]
Also add validation to genre, subtype and version fields.
Fixes: 11eeef41d5 ("netfilter: passive OS fingerprint xtables match")
Reported-by: Lucas Leong <wmliang@infosec.exchange>
Signed-off-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 894cafc5c6 ]
After running command [2] too many times in a row:
[1] $ tc qdisc add dev sw2p0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
[2] $ tc qdisc replace dev sw2p0 parent 1:1 cbs offload 1 \
idleslope 120000 sendslope -880000 locredit -1320 hicredit 180
(aka more than priv->info->num_cbs_shapers times)
we start seeing the following error message:
Error: Specified device failed to setup cbs hardware offload.
This comes from the fact that ndo_setup_tc(TC_SETUP_QDISC_CBS) presents
the same API for the qdisc create and replace cases, and the sja1105
driver fails to distinguish between the 2. Thus, it always thinks that
it must allocate the same shaper for a {port, queue} pair, when it may
instead have to replace an existing one.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 954ad9bf13 ]
More careful measurement of the tc-cbs bandwidth shows that the stream
bandwidth (effectively idleslope) increases, there is a larger and
larger discrepancy between the rate limit obtained by the software
Qdisc, and the rate limit obtained by its offloaded counterpart.
The discrepancy becomes so large, that e.g. at an idleslope of 40000
(40Mbps), the offloaded cbs does not actually rate limit anything, and
traffic will pass at line rate through a 100 Mbps port.
The reason for the discrepancy is that the hardware documentation I've
been following is incorrect. UM11040.pdf (for SJA1105P/Q/R/S) states
about IDLE_SLOPE that it is "the rate (in unit of bytes/sec) at which
the credit counter is increased".
Cross-checking with UM10944.pdf (for SJA1105E/T) and UM11107.pdf
(for SJA1110), the wording is different: "This field specifies the
value, in bytes per second times link speed, by which the credit counter
is increased".
So there's an extra scaling for link speed that the driver is currently
not accounting for, and apparently (empirically), that link speed is
expressed in Kbps.
I've pondered whether to pollute the sja1105_mac_link_up()
implementation with CBS shaper reprogramming, but I don't think it is
worth it. IMO, the UAPI exposed by tc-cbs requires user space to
recalculate the sendslope anyway, since the formula for that depends on
port_transmit_rate (see man tc-cbs), which is not an invariant from tc's
perspective.
So we use the offload->sendslope and offload->idleslope to deduce the
original port_transmit_rate from the CBS formula, and use that value to
scale the offload->sendslope and offload->idleslope to values that the
hardware understands.
Some numerical data points:
40Mbps stream, max interfering frame size 1500, port speed 100M
---------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -60000 locredit -900 hicredit 600
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 600 600
credit_lo 900 900
send_slope 7500000 75
idle_slope 5000000 50
40Mbps stream, max interfering frame size 1500, port speed 1G
-------------------------------------------------------------
tc-cbs parameters:
idleslope 40000 sendslope -960000 locredit -1440 hicredit 60
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 60 60
credit_lo 1440 1440
send_slope 120000000 120
idle_slope 5000000 5
5.12Mbps stream, max interfering frame size 1522, port speed 100M
-----------------------------------------------------------------
tc-cbs parameters:
idleslope 5120 sendslope -94880 locredit -1444 hicredit 77
which result in hardware values:
Before (doesn't work) After (works)
credit_hi 77 77
credit_lo 1444 1444
send_slope 11860000 118
idle_slope 640000 6
Tested on SJA1105T, SJA1105S and SJA1110A, at 1Gbps and 100Mbps.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6319685bdc ]
Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igb devices can use as low as 64 descriptors.
This change will unify igb with other drivers.
Based on commit 7b1be1987c ("e1000e: lower ring minimum size to 64")
Fixes: 9d5c824399 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8360717524 ]
Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igbvf devices can use as low as 64 descriptors.
This change will unify igbvf with other drivers.
Based on commit 7b1be1987c ("e1000e: lower ring minimum size to 64")
Fixes: d4e0fe01a3 ("igbvf: add new driver to support 82576 virtual functions")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aa4827971 ]
Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igc devices can use as low as 64 descriptors.
This change will unify igc with other drivers.
Based on commit 7b1be1987c ("e1000e: lower ring minimum size to 64")
Fixes: 0507ef8a03 ("igc: Add transmit and receive fastpath and interrupt handlers")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b192812905 ]
As with sk->sk_shutdown shown in the previous patch, sk->sk_err can be
read locklessly by unix_dgram_sendmsg().
Let's use READ_ONCE() for sk_err as well.
Note that the writer side is marked by commit cc04410af7 ("af_unix:
annotate lockless accesses to sk->sk_err").
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f31867d0d9 ]
The existing code incorrectly casted a negative value (the result of a
subtraction) to an unsigned value without checking. For example, if
/proc/sys/net/ipv6/conf/*/temp_prefered_lft was set to 1, the preferred
lifetime would jump to 4 billion seconds. On my machine and network the
shortest lifetime that avoided underflow was 3 seconds.
Fixes: 76506a986d ("IPv6: fix DESYNC_FACTOR")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151e887d8f ]
The veth_xmit function returns NETDEV_TX_OK even when packets are dropped.
This behavior leads to incorrect calculations of statistics counts, as
well as things like txq->trans_start updates.
Fixes: e314dbdc1c ("[NET]: Virtual ethernet device driver.")
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa09bc40b2 ]
Disable virtualization features on 82580 just as on i210/i211.
This avoids that virt functions are acidentally called on 82850.
Fixes: 55cac248ca ("igb: Add full support for 82580 devices")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ac66cb03a ]
Route hints when the nexthop is part of a multipath group causes packets
in the same receive batch to be sent to the same nexthop irrespective of
the multipath hash of the packet. So, do not extract route hint for
packets whose destination is part of a multipath group.
A new SKB flag IPSKB_MULTIPATH is introduced for this purpose, set the
flag when route is looked up in ip_mkroute_input() and use it in
ip_extract_route_hint() to check for the existence of the flag.
Fixes: 02b2494161 ("ipv4: use dst hint for ipv4 list receive")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a90c367e5a ]
Drop intel_vgpu_reset_gtt() as it no longer has any callers. In addition
to eliminating dead code, this eliminates the last possible scenario where
__kvmgt_protect_table_find() can be reached without holding vgpu_lock.
Requiring vgpu_lock to be held when calling __kvmgt_protect_table_find()
will allow a protecting the gfn hash with vgpu_lock without too much fuss.
No functional change intended.
Fixes: ba25d97757 ("drm/i915/gvt: Do not destroy ppgtt_mm during vGPU D3->D0.")
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Tested-by: Yongwei Ma <yongwei.ma@intel.com>
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Link: https://lore.kernel.org/r/20230729013535.1070024-11-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f60b12edc ]
This patch save/restore necessary GVT info during i915 suspend/resume so
that GVT enabled QEMU VM can continue running.
Only GGTT and fence regs are saved/restored now. GVT will save GGTT
entries on each host_entry update, restore the saved dirty entries
and re-init fence regs in resume routine.
V2:
- Change kzalloc/kfree to vzalloc/vfree since the space allocated
from kmalloc may not enough for all saved GGTT entries.
- Keep gvt suspend/resume wrapper in intel_gvt.h/intel_gvt.c and
move the actual implementation to gvt.h/gvt.c. (zhenyu)
- Check gvt config on and active with intel_gvt_active(). (zhenyu)
V3: (zhenyu)
- Incorrect copy length. Should be num entries * entry size.
- Use memcpy_toio()/memcpy_fromio() instead of memcpy for iomem.
- Add F_PM_SAVE flags to indicate which MMIOs to save/restore for PM.
V4:
Rebase.
V5:
Fail intel_gvt_save_ggtt as -ENOMEM if fail to alloc memory to save
ggtt. Free allocated ggtt_entries on failure.
V6:
Save host entry to per-vGPU gtt.ggtt_mm on each host_entry update.
V7:
Restore GGTT entry based on present bit.
Split fence restore and mmio restore in different functions.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20201027045308.158955-1-colin.xu@intel.com
Stable-dep-of: a90c367e5a ("drm/i915/gvt: Drop unused helper intel_vgpu_reset_gtt()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
