[ Upstream commit de5bfae2fd ]
The correct mask is 0x1f8 (Bit 3-8), but due to missing BIT() 0xf (Bit
0-3) was set instead. This means setting of CPCAP_BIT_MIC1_RX_TIMESLOT0
(Bit 3) still worked (part of both masks). On the other hand the code
does not properly clear the other MIC timeslot bits. I think this
is not a problem, since they are probably initialized to 0 and not
touched by the driver anywhere else. But the mask also contains some
wrong bits, that will be cleared. Bit 0 (CPCAP_BIT_SMB_CDC) should be
safe, since the driver enforces it to be 0 anyways.
Bit 1-2 are CPCAP_BIT_FS_INV and CPCAP_BIT_CLK_INV. This means enabling
audio recording forces the codec into SND_SOC_DAIFMT_NB_NF mode, which
is obviously bad.
The bug probably remained undetected, because there are not many use
cases for routing microphone to the CPU on platforms using cpcap and
user base is small. I do remember having some issues with bad sound
quality when testing voice recording back when I wrote the driver.
It probably was this bug.
Fixes: f6cdf2d344 ("ASoC: cpcap: new codec")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210123172945.3958622-1-sre@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10340f8d7b ]
While reworking the resources management and departing from using
ahci_platform_enable_resources() which did not allow a proper step
separation like we need, we unfortunately lost the ability to control
AHCI regulators. This broke some Broadcom STB systems that do expect
regulators to be turned on to link up with attached hard drives.
Fixes: c0cdf2ac4b ("ata: ahci_brcm: Fix AHCI resources management")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416b846757 ]
Talitos Security Engine AESU considers any input
data size that is not a multiple of 16 bytes to be an error.
This is not a problem in general, except for Counter mode
that is a stream cipher and can have an input of any size.
Test Manager for ctr(aes) fails on 4th test vector which has
a length of 499 while all previous vectors which have a 16 bytes
multiple length succeed.
As suggested by Freescale, round up the input data length to the
nearest 16 bytes.
Fixes: 5e75ae1b3c ("crypto: talitos - add new crypto modes")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ae78eec8a ]
If the task is pinned to a cpu, setting the misfit status means that
we'll unnecessarily continuously attempt to migrate the task but fail.
This continuous failure will cause the balance_interval to increase to
a high value, and eventually cause unnecessary significant delays in
balancing the system when real imbalance happens.
Caught while testing uclamp where rt-app calibration loop was pinned to
cpu 0, shortly after which we spawn another task with high util_clamp
value. The task was failing to migrate after over 40ms of runtime due to
balance_interval unnecessary expanded to a very high value from the
calibration loop.
Not done here, but it could be useful to extend the check for pinning to
verify that the affinity of the task has a cpu that fits. We could end
up in a similar situation otherwise.
Fixes: 3b1baa6496 ("sched/fair: Add 'group_misfit_task' load-balance type")
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Quentin Perret <qperret@google.com>
Acked-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lkml.kernel.org/r/20210119120755.2425264-1-qais.yousef@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc9455ffae ]
The Renkforce RF AC4K 300 Action Cam 4K reports invalid bFormatIndex and
bFrameIndex values when negotiating the video probe and commit controls.
The UVC descriptors report a single supported format and frame size,
with bFormatIndex and bFrameIndex both equal to 2, but the video probe
and commit controls report bFormatIndex and bFrameIndex set to 1.
The device otherwise operates correctly, but the driver rejects the
values and fails the format try operation. Fix it by ignoring the
invalid indices, and assuming that the format and frame requested by the
driver are accepted by the device.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=210767
Fixes: 8a652a17e3 ("media: uvcvideo: Ensure all probed info is returned to v4l2")
Reported-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 031b9212ee ]
When DEBUG is defined this error occurs
drivers/media/platform/pxa_camera.c:1410:7: error:
‘i’ undeclared (first use in this function)
for (i = 0; i < vb->num_planes; i++)
^
The variable 'i' is missing, so declare it.
Fixes: 6f28435d1c ("[media] media: platform: pxa_camera: trivial move of functions")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2de3643c5 ]
This function looks like a realloc.
However, if 'risc->cpu != NULL', the memory will be freed, but never
reallocated with the bigger 'size'.
Explicitly set 'risc->cpu' to NULL, so that the reallocation is
correctly performed a few lines below.
[hverkuil: NULL != risc->cpu -> risc->cpu]
Fixes: 5ede94c705 ("[media] cx25821: remove bogus btcx_risc dependency)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59a3e78f8c ]
There's a comma used instead of a semicolon that causes multiple
statements to be executed after an if instead of just the intended
single statement.
Replace the comma with a semicolon.
Fixes: 15e1ce3318 ("[media] lmedm04: Fix usb_submit_urb BOGUS urb xfer, pipe 1 != type 3 in interrupt urb")
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa18405ba ]
This fixes corrupted display output in HDMI deep color
10/12 bpc mode at least as observed on AMD Mullins, DCE-8.3.
It will hopefully also provide fixes for other DCE's up to
DCE-11, assuming those will need similar fixes, but i could
not test that for HDMI due to lack of suitable hw, so viewer
discretion is advised.
dce110_stream_encoder_hdmi_set_stream_attribute() is used for
HDMI setup on all DCE's and is missing color_depth assignment.
dce110_program_pix_clk() is used for pixel clock setup on HDMI
for DCE 6-11, and is missing color_depth assignment.
Additionally some of the underlying Atombios specific encoder
and pixelclock setup functions are missing code which is in
the classic amdgpu kms modesetting path and the in the radeon
kms driver for DCE6/DCE8.
encoder_control_digx_v3() - Was missing setup code wrt. amdgpu
and radeon kms classic drivers. Added here, but untested due to
lack of suitable test hw.
encoder_control_digx_v4() - Added missing setup code.
Successfully tested on AMD mullins / DCE-8.3 with HDMI deep color
output at 10 bpc and 12 bpc.
Note that encoder_control_digx_v5() has proper setup code in place
and is used, e.g., by DCE-11.2, but this code wasn't used for deep
color setup due to the missing cntl.color_depth setup in the calling
function for HDMI.
set_pixel_clock_v5() - Missing setup code wrt. classic amdgpu/radeon
kms. Added here, but untested due to lack of hw.
set_pixel_clock_v6() - Missing setup code added. Successfully tested
on AMD mullins DCE-8.3. This fixes corrupted display output at HDMI
deep color output with 10 bpc or 12 bpc.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1916866dfa ]
In set_clamp(), the comments and definitions for the COLOR_DEPTH_101010
and COLOR_DEPTH_121212 cases directly contradict the code comment which
explains how this should work, whereas the COLOR_DEPTH_888 case
is consistent with the code comments. Comment says the bitmask should
be chosen to align to the top-most 10 or 12 MSB's on a 14 bit bus, but
the implementation contradicts that: 10 bit case sets a mask for 12 bpc
clamping, whereas 12 bit case sets a mask for 14 bpc clamping.
Note that during my limited testing on DCE-8.3 (HDMI deep color)
and DCE-11.2 (DP deep color), this didn't have any obvious ill
effects, neither did fixing it change anything obvious for the
better, so this fix may be inconsequential on DCE, and just
reduce the confusion of innocent bystanders when reading the code
and trying to investigate problems with 10 bpc+ output.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 894ef53001 ]
Commit 866b6a89c6 ("MIPS: Add DWARF unwinding to assembly") added
-fno-asynchronous-unwind-tables to KBUILD_CFLAGS to prevent compiler
from emitting .eh_frame symbols.
However, as MIPS heavily uses CFI, that's not enough. Use the
approach taken for x86 (as it also uses CFI) and explicitly put CFI
symbols into the .debug_frame section (except for VDSO).
This allows us to drop .eh_frame from DISCARDS as it's no longer
being generated.
Fixes: 866b6a89c6 ("MIPS: Add DWARF unwinding to assembly")
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67f4aeb2b4 ]
During commit 88bc417856 ("drm: Use new
DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags") DRM_BUS_FLAG_*
macros have been changed to avoid ambiguity but just because of this
ambiguity previous DRM_BUS_FLAG_PIXDATA_(POS/NEG)EDGE were used meaning
_SAMPLE_ not _DRIVE_. This leads to DLCK inversion and need to fix but
instead of swapping phase values, let's adopt an easier approach Maxime
suggested:
It turned out that bit 26 of SUN4I_TCON0_IO_POL_REG is dedicated to
invert DCLK polarity and this makes things really easier than before. So
let's handle DCLK polarity by adding SUN4I_TCON0_IO_POL_DCLK_DRIVE_NEGEDGE
as bit 26 and activating according to bus_flags the same way it is done
for all the other signals polarity.
Fixes: 88bc417856 ("drm: Use new DRM_BUS_FLAG_*_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags")
Suggested-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114081732.9386-1-giulio.benetti@benettiengineering.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7f2b43eaf ]
Renaming 'struct device_private' to 'struct bcm_device_private',
because it clashes with 'struct device_private' from
'drivers/base/base.h'.
While it's not a functional problem, it's causing two distinct
type hierarchies in BTF data. It also breaks build with options:
CONFIG_DEBUG_INFO_BTF=y
CONFIG_CRYPTO_DEV_BCM_SPU=y
as reported by Qais Yousef [1].
[1] https://lore.kernel.org/lkml/20201229151352.6hzmjvu3qh6p2qgg@e107158-lin/
Fixes: 9d12ba86f8 ("crypto: brcm - Add Broadcom SPU driver")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76aaf8a967 ]
When usb_clear_halt() fails, dvb->bulk_urb->transfer_buffer
and dvb->bulk_urb should be freed just like when
usb_submit_urb() fails.
Fixes: 3169c9b26f ("V4L/DVB (12788): tm6000: Add initial DVB-T support")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a26efd1961 ]
When kzalloc() fails, em28xx_uninit_usb_xfer() will free
usb_bufs->buf and set it to NULL. Thus the later access
to usb_bufs->buf[i] will lead to null pointer dereference.
Also the kfree(usb_bufs->buf) after that is redundant.
Fixes: d571b592c6 ("media: em28xx: don't use coherent buffer for DMA transfers")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89b14485ca ]
The csc/scaler device private struct is released by
ipu_csc_scaler_video_device_release(), which can be called
by video_unregister_device() if there are no users
of the underlying struct video device.
Therefore, the mutex can't be held when calling
video_unregister_device() as its memory may be freed
by it, leading to a kernel oops.
Fortunately, the fix is quite simple as no locking
is needed when calling video_unregister_device(): v4l2-core
already has its own internal locking, and the structures
are also properly refcounted.
Fixes: a8ef0488cc ("media: imx: add csc/scaler mem2mem device")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb2216548a ]
The csc/scaler device pointer (imxmd->m2m_vdev) is assigned
after the imx media device v4l2-async probe completes,
therefore we need to check if the device is non-NULL
before trying to unregister it.
This can be the case if the non-completed imx media device
is unbinded (or the driver is removed), leading to a kernel oops.
Fixes: a8ef0488cc ("media: imx: add csc/scaler mem2mem device")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc1eb7c9c2 ]
The driver currently reports a single supported value for
V4L2_CID_PIXEL_RATE and initializes the control's minimum value to 0,
which is very risky, as userspace might accidentally use it as divider
when calculating the time duration of a line.
Fix this by using as minimum the only supported value when registering
the control.
Fixes: 5de35c9b8d ("media: i2c: Add Omnivision OV5670 5M sensor support")
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6f2a9e17b ]
When building xway_defconfig with clang:
arch/mips/lantiq/irq.c:305:48: error: use of logical '&&' with constant
operand [-Werror,-Wconstant-logical-operand]
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
^ ~~~~~~~~~~~~~~~~~
arch/mips/lantiq/irq.c:305:48: note: use '&' for a bitwise operation
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
^~
&
arch/mips/lantiq/irq.c:305:48: note: remove constant to silence this
warning
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
~^~~~~~~~~~~~~~~~~~~~
1 error generated.
Explicitly compare the constant LTQ_EBU_PCC_ISTAT against 0 to fix the
warning. Additionally, remove the unnecessary parentheses as this is a
simple conditional statement and shorthand '== 0' to '!'.
Fixes: 3645da0276 ("OF: MIPS: lantiq: implement irq_domain support")
Link: https://github.com/ClangBuiltLinux/linux/issues/807
Reported-by: Dmitry Golovin <dima@golovin.in>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c58734eee6 ]
When building with clang, the following section mismatch warning occurs:
WARNING: modpost: vmlinux.o(.text+0x24490): Section mismatch in
reference from the function r4k_cache_init() to the function
.init.text:loongson2_sc_init()
This should have been fixed with commit ad4fddef5f ("mips: fix Section
mismatch in reference") but it was missed. Remove the improper __init
annotation like that commit did.
Fixes: 078a55fc82 ("MIPS: Delete __cpuinit/__CPUINIT usage from MIPS code")
Link: https://github.com/ClangBuiltLinux/linux/issues/787
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15deb4333c ]
Commit 69b6f2e817 ("crypto: arm64/aes-neon - limit exposed routines if
faster driver is enabled") intended to hide modes from the plain NEON
driver that are also implemented by the faster bit sliced NEON one if
both are enabled. However, the defined() CPP function does not detect
if the bit sliced NEON driver is enabled as a module. So instead, let's
use IS_ENABLED() here.
Fixes: 69b6f2e817 ("crypto: arm64/aes-neon - limit exposed routines if ...")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bc3dd24e7 ]
With the recent kmap change, some tests which were conditional on
CONFIG_DEBUG_HIGHMEM now are enabled by default.
This permit to detect a problem in sun4i-ss usage of kmap.
sun4i-ss uses two kmap via sg_miter (one for input, one for output), but
using two kmap at the same time is hard:
"the ordering has to be correct and with sg_miter that's probably hard to get
right." (quoting Tlgx)
So the easiest solution is to never have two sg_miter/kmap open at the same time.
After each use of sg_miter, I store the current index, for being able to
resume sg_miter to the right place.
Fixes: 6298e94821 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 583513510a ]
When running the non-optimized cipher function, SS produce partial random
output.
This is due to linearize buffers being reseted after each loop.
For preserving stack, instead of moving them back to start of function,
I move them in sun4i_ss_ctx.
Fixes: 8d3bcb9900 ("crypto: sun4i-ss - reduce stack usage")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ccc39b3a ]
The main problem with this error handling was that it didn't clean up if
i2c_add_numbered_adapter() failed. This code is pretty old, and doesn't
match with today's checkpatch.pl standards so I took the opportunity to
tidy it up a bit. I changed the NULL comparison, and removed the
WARNING message if kzalloc() fails and updated the label names.
Fixes: 1b082ccf59 ("gma500: Add Oaktrail support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/X8ikkAqZfnDO2lu6@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf9bf87128 ]
According to Errata #23 "The per-CPU GbE interrupt is limited to Core
0", we can't use the per-cpu interrupt mechanism on the Armada 3700
familly.
This is correctly checked for RSS configuration, but the initial queue
mapping is still done by having the queues spread across all the CPUs in
the system, both in the init path and in the cpu_hotplug path.
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eab3fdb41 ]
Frequent link up/down events can happen when a Bel Fuse SFP part is
connected to the amd-xgbe device. Try to avoid the frequent link
issues by resetting the PHY as documented in Bel Fuse SFP datasheets.
Fixes: e722ec8237 ("amd-xgbe: Update the BelFuse quirk to support SGMII")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84fe68eb67 ]
Normally, auto negotiation and reconnect should be automatically done by
the hardware. But there seems to be an issue where auto negotiation has
to be restarted manually. This happens because of link training and so
even though still connected to the partner the link never "comes back".
This needs an auto-negotiation restart.
Also, a change in xgbe-mdio is needed to get ethtool to recognize the
link down and get the link change message. This change is only
required in a backplane connection mode.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30b7edc82e ]
Sometimes mailbox commands timeout when the RX data path becomes
unresponsive. This prevents the submission of new mailbox commands to DXIO.
This patch identifies the timeout and resets the RX data path so that the
next message can be submitted properly.
Fixes: 549b32af9f ("amd-xgbe: Simplify mailbox interface rate change code")
Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d3a7b9ea5 ]
Timeout reset will trigger the VIOS to unmap it automatically,
similarly as FAILVOER and MOBILITY events. If we unmap it
in the linux side, we will see errors like
"30000003: Error 4 in REQUEST_UNMAP_RSP".
So, don't call send_request_unmap for timeout reset.
Fixes: ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42557dab78 ]
dma_rmb() barrier is added to load the long term buffer before copying
it to socket buffer; and dma_wmb() barrier is added to update the
long term buffer before it being accessed by VIOS (virtual i/o server).
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Acked-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4773acf3d4 ]
The documentation for the PHY update [1] states:
Loop 4 times with index i
If PHY Revision >= 3
Copy table[i] to coef[i]
Otherwise
Set coef[i] to 0
the copy of the table to coef is currently implemented the wrong way
around, table is being updated from uninitialized values in coeff.
Fix this by swapping the assignment around.
[1] https://bcm-v4.sipsolutions.net/802.11/PHY/N/RestoreCal/
Fixes: 2f258b74d1 ("b43: N-PHY: implement restoring general configuration")
Addresses-Coverity: ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2355a6773a ]
The Max imm data size in cxgb4 is not similar to the max imm data size
in the chtls. This caused an mismatch in output of is_ofld_imm() of
cxgb4 and chtls. So fixed this by keeping the max wreq size of imm data
same in both chtls and cxgb4 as MAX_IMM_OFLD_TX_DATA_WR_LEN.
As cxgb4's max imm. data value for ofld packets is changed to
MAX_IMM_OFLD_TX_DATA_WR_LEN. Using the same in cxgbit also.
Fixes: 36bedb3f2e ("crypto: chtls - Inline TLS record Tx")
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57baf8cc70 ]
This driver is set up to use a clock mapping in the device tree if it is
present, but still work without one for backward compatibility. However,
if getting the clock returns -EPROBE_DEFER, then we need to abort and
return that error from our driver initialization so that the probe can
be retried later after the clock is set up.
Move clock initialization to earlier in the process so we do not waste as
much effort if the clock is not yet available. Switch to use
devm_clk_get_optional and abort initialization on any error reported.
Also enable the clock regardless of whether the controller is using an MDIO
bus, as the clock is required in any case.
Fixes: 09a0354cad ("net: axienet: Use clock framework to get device clock rate")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
