[ Upstream commit 395a41a1d3e377462f3eea8a205ee72be8885ff6 ]
If regulator_get() in of_regulator_bulk_get_all() returns an error, that
error gets overridden and -EINVAL is always passed out. This masks probe
deferral requests and likely won't work properly in all cases.
Fix this by letting of_regulator_bulk_get_all() return the original
error code.
Fixes: 27b9ecc7a9 ("regulator: Add of_regulator_bulk_get_all")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patch.msgid.link/20240822072047.3097740-3-wenst@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2317d018b835842df0501d8f9e9efa843068a101 ]
The speedbin eFuse reads a value 'x' from 0 to 7 and, in order to
make that compatible with opp-supported-hw, it gets post processed
as BIT(x).
Change all of the 0x30 supported-hw to 0x20 to avoid getting
duplicate OPPs for speedbin 4, and also change all of the 0x8 to
0xcf because speedbins different from 4 and 5 do support 900MHz,
950MHz, 1000MHz with the higher voltage of 850mV, 900mV, 950mV
respectively.
Fixes: f38ea593ad ("arm64: dts: mediatek: mt8186: Wire up GPU voltage/frequency scaling")
Link: https://lore.kernel.org/r/20240725072243.173104-1-angelogioacchino.delregno@collabora.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26e197b7f9240a4ac301dd0ad520c0c697c2ea7d ]
The blk_add_partition() function initially used a single if-condition
(IS_ERR(part)) to check for errors when adding a partition. This was
modified to handle the specific case of -ENXIO separately, allowing the
function to proceed without logging the error in this case. However,
this change unintentionally left a path where md_autodetect_dev()
could be called without confirming that part is a valid pointer.
This commit separates the error handling logic by splitting the
initial if-condition, improving code readability and handling specific
error scenarios explicitly. The function now distinguishes the general
error case from -ENXIO without altering the existing behavior of
md_autodetect_dev() calls.
Fixes: b72053072c (block: allow partitions on host aware zone devices)
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240911132954.5874-1-riyandhiman14@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0997aa5497c714edbb349ca366d28bd550ba3408 ]
The io worker threads are userland threads that just never exit to the
userland. By that, they are also assigned to a cgroup (the group of the
creating task).
When changing the affinity of the io_wq thread via syscall, we must only
allow cpumasks within the limits defined by the cpuset controller of the
cgroup (if enabled).
Fixes: da64d6db3b ("io_uring: One wqe per wq")
Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com>
Link: https://lore.kernel.org/r/20240910171157.166423-2-felix.moessbauer@siemens.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73aeab373557fa6ee4ae0b742c6211ccd9859280 ]
Original state:
Process 1 Process 2 Process 3 Process 4
(BIC1) (BIC2) (BIC3) (BIC4)
Λ | | |
\--------------\ \-------------\ \-------------\|
V V V
bfqq1--------->bfqq2---------->bfqq3----------->bfqq4
ref 0 1 2 4
After commit 0e456dba86c7 ("block, bfq: choose the last bfqq from merge
chain in bfq_setup_cooperator()"), if P1 issues a new IO:
Without the patch:
Process 1 Process 2 Process 3 Process 4
(BIC1) (BIC2) (BIC3) (BIC4)
Λ | | |
\------------------------------\ \-------------\|
V V
bfqq1--------->bfqq2---------->bfqq3----------->bfqq4
ref 0 0 2 4
bfqq3 will be used to handle IO from P1, this is not expected, IO
should be redirected to bfqq4;
With the patch:
-------------------------------------------
| |
Process 1 Process 2 Process 3 | Process 4
(BIC1) (BIC2) (BIC3) | (BIC4)
| | | |
\-------------\ \-------------\|
V V
bfqq1--------->bfqq2---------->bfqq3----------->bfqq4
ref 0 0 2 4
IO is redirected to bfqq4, however, procress reference of bfqq3 is still
2, while there is only P2 using it.
Fix the problem by calling bfq_merge_bfqqs() for each bfqq in the merge
chain. Also change bfqq_merge_bfqqs() to return new_bfqq to simplify
code.
Fixes: 0e456dba86c7 ("block, bfq: choose the last bfqq from merge chain in bfq_setup_cooperator()")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240909134154.954924-3-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ba0403ac6447f2d63914fb760c44a3b19c44eaf ]
After commit 42c306ed7233 ("block, bfq: don't break merge chain in
bfq_split_bfqq()"), if the current procress is the last holder of bfqq,
the bfqq can be freed after bfq_split_bfqq(). Hence recored the bfqq and
then access bfqq->waker_bfqq may trigger UAF. What's more, the waker_bfqq
may in the merge chain of bfqq, hence just recored waker_bfqq is still
not safe.
Fix the problem by adding a helper bfq_waker_bfqq() to check if
bfqq->waker_bfqq is in the merge chain, and current procress is the only
holder.
Fixes: 42c306ed7233 ("block, bfq: don't break merge chain in bfq_split_bfqq()")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240909134154.954924-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42c306ed723321af4003b2a41bb73728cab54f85 ]
Consider the following scenario:
Process 1 Process 2 Process 3 Process 4
(BIC1) (BIC2) (BIC3) (BIC4)
Λ | | |
\-------------\ \-------------\ \--------------\|
V V V
bfqq1--------->bfqq2---------->bfqq3----------->bfqq4
ref 0 1 2 4
If Process 1 issue a new IO and bfqq2 is found, and then bfq_init_rq()
decide to spilt bfqq2 by bfq_split_bfqq(). Howerver, procress reference
of bfqq2 is 1 and bfq_split_bfqq() just clear the coop flag, which will
break the merge chain.
Expected result: caller will allocate a new bfqq for BIC1
Process 1 Process 2 Process 3 Process 4
(BIC1) (BIC2) (BIC3) (BIC4)
| | |
\-------------\ \--------------\|
V V
bfqq1--------->bfqq2---------->bfqq3----------->bfqq4
ref 0 0 1 3
Since the condition is only used for the last bfqq4 when the previous
bfqq2 and bfqq3 are already splited. Fix the problem by checking if
bfqq is the last one in the merge chain as well.
Fixes: 36eca89483 ("block, bfq: add Early Queue Merge (EQM)")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240902130329.3787024-4-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e456dba86c7f9a19792204a044835f1ca2c8dbb ]
Consider the following merge chain:
Process 1 Process 2 Process 3 Process 4
(BIC1) (BIC2) (BIC3) (BIC4)
Λ | | |
\--------------\ \-------------\ \-------------\|
V V V
bfqq1--------->bfqq2---------->bfqq3----------->bfqq4
IO from Process 1 will get bfqf2 from BIC1 first, then
bfq_setup_cooperator() will found bfqq2 already merged to bfqq3 and then
handle this IO from bfqq3. However, the merge chain can be much deeper
and bfqq3 can be merged to other bfqq as well.
Fix this problem by iterating to the last bfqq in
bfq_setup_cooperator().
Fixes: 36eca89483 ("block, bfq: add Early Queue Merge (EQM)")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240902130329.3787024-3-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9ea57c91f03bcad415e1a20113bdb2077bcf990 ]
If request timetout is handled by nbd_requeue_cmd(), normal completion
has to be stopped for avoiding to complete this requeued request, other
use-after-free can be triggered.
Fix the race by clearing NBD_CMD_INFLIGHT in nbd_requeue_cmd(), meantime
make sure that cmd->lock is grabbed for clearing the flag and the
requeue.
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Fixes: 2895f1831e ("nbd: don't clear 'NBD_CMD_INFLIGHT' flag if request is not completed")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20240830034145.1827742-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9327b51c9a9c864f5177127e09851da9d78b4943 ]
ublk zoned takes 16 bytes in each request pdu just for handling REPORT_ZONE
operation, this way does waste memory since request pdu is allocated
statically.
Store the transient zone report data into one global xarray, and remove
it after the report zone request is completed. This way is reasonable
since report zone is run in slow code path.
Fixes: 29802d7ca3 ("ublk: enable zoned storage support")
Cc: Damien Le Moal <dlemoal@kernel.org>
Cc: Andreas Hindborg <a.hindborg@samsung.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240812013624.587587-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99655a304e450baaae6b396cb942b9e47659d644 ]
Clang static checker (scan-build) warning:
net/tipc/bcast.c:305:4:
The expression is an uninitialized value. The computed value will also
be garbage [core.uninitialized.Assign]
305 | (*cong_link_cnt)++;
| ^~~~~~~~~~~~~~~~~~
tipc_rcast_xmit() will increase cong_link_cnt's value, but cong_link_cnt
is uninitialized. Although it won't really cause a problem, it's better
to fix it.
Fixes: dca4a17d24 ("tipc: fix potential hanging after b/rcast changing")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Link: https://patch.msgid.link/20240912110119.2025503-1-suhui@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9c7ac4fe22c608acf6153a3329df2b6b6cd416c ]
En-Wei reported that traffic breaks if cable is unplugged for more
than 3s and then re-plugged. This was supposed to be fixed by
621735f59064 ("r8169: fix rare issue with broken rx after link-down on
RTL8125"). But apparently this didn't fix the issue for everybody.
The 3s threshold rang a bell, as this is the delay after which ALDPS
kicks in. And indeed disabling ALDPS fixes the issue for this user.
Maybe this fixes the issue in general. In a follow-up step we could
remove the first fix attempt and see whether anybody complains.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Tested-by: En-Wei WU <en-wei.wu@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/778b9d86-05c4-4856-be59-cde4487b9e52@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fa29c85117170b0508790f878b13ec6593c888 ]
Bareudp reads the inner IP header to get the ECN value. Therefore, it
needs to ensure that it's part of the skb's linear data.
This is similar to the vxlan and geneve fixes for that same problem:
* commit f7789419137b ("vxlan: Pull inner IP header in vxlan_rcv().")
* commit 1ca1ba465e55 ("geneve: make sure to pull inner header in
geneve_rx()")
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/5205940067c40218a70fbb888080466b2fc288db.1726046181.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b05933340f4490ef5b09e84d644d12484b05fdf ]
Requesting transfers of the exact same size of wMaxPacketSize may result
in ZPL/short-transfer since the USB stack cannot handle it as we are
limiting the buffer size to be the same as wMaxPacketSize.
Also, in terms of throughput this change has the same effect to
interrupt endpoint as 290ba20081 "Bluetooth: Improve USB driver throughput
by increasing the frame size" had for the bulk endpoint, so users of the
advertisement bearer (e.g. BT Mesh) may benefit from this change.
Fixes: 5e23b923da ("[Bluetooth] Add generic driver for Bluetooth USB devices")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c09b50efcad985cf920ca88baa9aa52b1999dcc ]
After calling m_can_stop() an interrupt may be pending or NAPI might
still be executed. This means the driver might still touch registers
of the IP core after the clocks have been disabled. This is not good
practice and might lead to aborts depending on the SoC integration.
To avoid these potential problems, make m_can_close() symmetric to
m_can_open(), i.e. stop the clocks at the end, right before shutting
down the transceiver.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-2-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 801ad2f87b0c6d0c34a75a4efd6bfd3a2d9f9298 ]
If an interrupt (RX-complete or error flag) is set when bringing up
the CAN device, e.g. due to CAN bus traffic before initializing the
device, when m_can_start() is called and interrupts are enabled,
m_can_isr() is called immediately, which disables all CAN interrupts
and calls napi_schedule().
Because napi_enable() isn't called until later in m_can_open(), the
call to napi_schedule() never schedules the m_can_poll() callback and
the device is left with interrupts disabled and can't receive any CAN
packets until rebooted.
This can be verified by running "cansend" from another device before
setting the bitrate and calling "ip link set up can0" on the test
device. Adding debug lines to m_can_isr() shows it's called with flags
(IR_EP | IR_EW | IR_CRCE), which calls m_can_disable_all_interrupts()
and napi_schedule(), and then m_can_poll() is never called.
Move the call to napi_enable() above the call to m_can_start() to
enable any initial interrupt flags to be handled by m_can_poll() so
that interrupts are reenabled. Add a call to napi_disable() in the
error handling section of m_can_open(), to handle the case where later
functions return errors.
Also, in m_can_close(), move the call to napi_disable() below the call
to m_can_stop() to ensure all interrupts are handled when bringing
down the device. This race condition is much less likely to occur.
Tested on a Microchip SAMA7G54 MPU. The fix should be applicable to
any SoC with a Bosch M_CAN controller.
Signed-off-by: Jake Hamby <Jake.Hamby@Teledyne.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Link: https://patch.msgid.link/20240910-can-m_can-fix-ifup-v3-1-6c1720ba45ce@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfbfeee61582e638770a1a10deef866c9adb38f5 ]
This ignores errors from HCI_OP_REMOTE_NAME_REQ_CANCEL since it
shouldn't interfere with the stopping of discovery and in certain
conditions it seems to be failing.
Link: https://github.com/bluez/bluez/issues/575
Fixes: d0b137062b ("Bluetooth: hci_sync: Rework init stages")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d47da6bd4cfa982fe903f33423b9e2ec541e9496 ]
If HCI_CONN_MGMT_CONNECTED has been set then the event shall be
HCI_CONN_MGMT_DISCONNECTED.
Fixes: b644ba3369 ("Bluetooth: Update device_connected and device_found events to latest API")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7c6ae1efb1ff68bc01d79d94fdf0388f86cdd8 ]
In the `wilc_parse_join_bss_param` function, the TSF field of the `ies`
structure is accessed after the RCU read-side critical section is
unlocked. According to RCU usage rules, this is illegal. Reusing this
pointer can lead to unpredictable behavior, including accessing memory
that has been updated or causing use-after-free issues.
This possible bug was identified using a static analysis tool developed
by myself, specifically designed to detect RCU-related issues.
To address this, the TSF value is now stored in a local variable
`ies_tsf` before the RCU lock is released. The `param->tsf_lo` field is
then assigned using this local variable, ensuring that the TSF value is
safely accessed.
Fixes: 205c50306acf ("wifi: wilc1000: fix RCU usage in connect path")
Signed-off-by: Jiawei Ye <jiawei.ye@foxmail.com>
Reviewed-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/tencent_466225AA599BA49627FB26F707EE17BC5407@qq.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d301de12da6e1bb069a9835c38359b8e8135121 ]
Since '__dev_queue_xmit()' should be called with interrupts enabled,
the following backtrace:
ieee80211_do_stop()
...
spin_lock_irqsave(&local->queue_stop_reason_lock, flags)
...
ieee80211_free_txskb()
ieee80211_report_used_skb()
ieee80211_report_ack_skb()
cfg80211_mgmt_tx_status_ext()
nl80211_frame_tx_status()
genlmsg_multicast_netns()
genlmsg_multicast_netns_filtered()
nlmsg_multicast_filtered()
netlink_broadcast_filtered()
do_one_broadcast()
netlink_broadcast_deliver()
__netlink_sendskb()
netlink_deliver_tap()
__netlink_deliver_tap_skb()
dev_queue_xmit()
__dev_queue_xmit() ; with IRQS disabled
...
spin_unlock_irqrestore(&local->queue_stop_reason_lock, flags)
issues the warning (as reported by syzbot reproducer):
WARNING: CPU: 2 PID: 5128 at kernel/softirq.c:362 __local_bh_enable_ip+0xc3/0x120
Fix this by implementing a two-phase skb reclamation in
'ieee80211_do_stop()', where actual work is performed
outside of a section with interrupts disabled.
Fixes: 5061b0c2b9 ("mac80211: cooperate more with network namespaces")
Reported-by: syzbot+1a3986bbd3169c307819@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=1a3986bbd3169c307819
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20240906123151.351647-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ea13b1b1fbf6364d4cd568e65e4c8479632999 ]
Although not reproduced in practice, these two cases may be
considered by UBSAN as off-by-one errors. So fix them in the
same way as in commit a26a5107bc52 ("wifi: cfg80211: fix UBSAN
noise in cfg80211_wext_siwscan()").
Fixes: 807f8a8c30 ("cfg80211/nl80211: add support for scheduled scans")
Fixes: 5ba63533bb ("cfg80211: fix alignment problem in scan request")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20240909090806.1091956-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d197d37809b220616a0fb00856b9eeeafe1f69e ]
If TLV includes beacon content, its length might not be 4-byte aligned.
Make sure the length is aligned before sending beacon commands to FW.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stable-dep-of: 9e461f4a2329 ("wifi: mt76: mt7996: fix uninitialized TLV data")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a26a5107bc52922cf5f67361e307ad66547b51c7 ]
Looking at https://syzkaller.appspot.com/bug?extid=1a3986bbd3169c307819
and running reproducer with CONFIG_UBSAN_BOUNDS, I've noticed the
following:
[ T4985] UBSAN: array-index-out-of-bounds in net/wireless/scan.c:3479:25
[ T4985] index 164 is out of range for type 'struct ieee80211_channel *[]'
<...skipped...>
[ T4985] Call Trace:
[ T4985] <TASK>
[ T4985] dump_stack_lvl+0x1c2/0x2a0
[ T4985] ? __pfx_dump_stack_lvl+0x10/0x10
[ T4985] ? __pfx__printk+0x10/0x10
[ T4985] __ubsan_handle_out_of_bounds+0x127/0x150
[ T4985] cfg80211_wext_siwscan+0x11a4/0x1260
<...the rest is not too useful...>
Even if we do 'creq->n_channels = n_channels' before 'creq->ssids =
(void *)&creq->channels[n_channels]', UBSAN treats the latter as
off-by-one error. Fix this by using pointer arithmetic rather than
an expression with explicit array indexing and use convenient
'struct_size()' to simplify the math here and in 'kzalloc()' above.
Fixes: 5ba63533bb ("cfg80211: fix alignment problem in scan request")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20240905150400.126386-1-dmantipov@yandex.ru
[fix coding style for multi-line calculation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b04f06fc0243600665b3b50253869533b7938468 ]
The master ooo cannot be completely closed when the
accelerator core reports memory error. Therefore, the driver
needs to inject the qm error to close the master ooo. Currently,
the qm error is injected after stopping queue, memory may be
released immediately after stopping queue, causing the device to
access the released memory. Therefore, error is injected to close master
ooo before stopping queue to ensure that the device does not access
the released memory.
Fixes: 6c6dd5802c ("crypto: hisilicon/qm - add controller reset interface")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d2d1ee0874c26b8010ddf7f57e2f246e848af38 ]
Before the device is enabled again, the device may still
store the previously processed data. If an error occurs in
the previous task, the device may fail to be enabled again.
Therefore, before enabling device, reset the device to restore
the initial state.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: b04f06fc0243 ("crypto: hisilicon/qm - inject error before stopping queue")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 145013f723947c83b1a5f76a0cf6e7237d59e973 ]
The timeout threshold of the hpre cluster is 16ms. When the CPU
and device share virtual address, page fault processing time may
exceed the threshold.
In the current test, there is a high probability that the
cluster times out. However, the cluster is waiting for the
completion of memory access, which is not an error, the device
does not need to be reset. If an error occurs in the cluster,
qm also reports the error. Therefore, the cluster timeout
error of hpre can be masked.
Fixes: d90fab0deb ("crypto: hisilicon/qm - get error type from hardware registers")
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b80294fb53845dc5c98cca0c989da09150f2ca9 ]
There was a symbol listed in the powercap.h file that was not implemented.
Implement it with a stub return of 0.
Programs like SWIG require that functions that are defined in the
headers be implemented.
Fixes: c2294c1496 ("cpupower: Introduce powercap intel-rapl library and powercap-info command")
Suggested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: John B. Wyatt IV <jwyatt@redhat.com>
Signed-off-by: John B. Wyatt IV <sageofredondo@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c936844010466535bd46ea4ce4656ef17653644 ]
When the current node doesn't have an EPC section configured by firmware
and all other EPC sections are used up, CPU can get stuck inside the
while loop that looks for an available EPC page from remote nodes
indefinitely, leading to a soft lockup. Note how nid_of_current will
never be equal to nid in that while loop because nid_of_current is not
set in sgx_numa_mask.
Also worth mentioning is that it's perfectly fine for the firmware not
to setup an EPC section on a node. While setting up an EPC section on
each node can enhance performance, it is not a requirement for
functionality.
Rework the loop to start and end on *a* node that has SGX memory. This
avoids the deadlock looking for the current SGX-lacking node to show up
in the loop when it never will.
Fixes: 901ddbb9ec ("x86/sgx: Add a basic NUMA allocation scheme to sgx_alloc_epc_page()")
Reported-by: "Molina Sabido, Gerardo" <gerardo.molina.sabido@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Zhimin Luo <zhimin.luo@intel.com>
Link: https://lore.kernel.org/all/20240905080855.1699814-2-aaron.lu%40intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
