commit ece6031ece upstream.
The GPU regulator enable ramp delay for Jetson TX1 is set to 1ms which
not sufficient because the enable ramp delay has been measured to be
greater than 1ms. Furthermore, the downstream kernels released by NVIDIA
for Jetson TX1 are using a enable ramp delay 2ms and a settling delay of
160us. Update the GPU regulator enable ramp delay for Jetson TX1 to be
2ms and add a settling delay of 160us.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 5e6b9a89af ("arm64: tegra: Add VDD_GPU regulator to Jetson TX1")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16da0eb5ab upstream.
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 771a081e44 upstream.
In the function alps_is_cs19_trackpoint(), we check if the param[1] is
in the 0x20~0x2f range, but the code we wrote for this checking is not
correct:
(param[1] & 0x20) does not mean param[1] is in the range of 0x20~0x2f,
it also means the param[1] is in the range of 0x30~0x3f, 0x60~0x6f...
Now fix it with a new condition checking ((param[1] & 0xf0) == 0x20).
Fixes: 7e4935ccc3 ("Input: alps - don't handle ALPS cs19 trackpoint-only device")
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1976d7d200 upstream.
Adds the Lenovo T580 to the SMBus intertouch list for Synaptics
touchpads. I've tested with this for a week now, and it seems a great
improvement. It's also nice to have the complaint gone from dmesg.
Signed-off-by: Nick Black <dankamongmen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e4935ccc3 upstream.
On a latest Lenovo laptop, the trackpoint and 3 buttons below it
don't work at all, when we move the trackpoint or press those 3
buttons, the kernel will print out:
"Rejected trackstick packet from non DualPoint device"
This device is identified as an alps touchpad but the packet has
trackpoint format, so the alps.c drops the packet and prints out
the message above.
According to XiaoXiao's explanation, this device is named cs19 and
is trackpoint-only device, its firmware is only for trackpoint, it
is independent of touchpad and is a device completely different from
DualPoint ones.
To drive this device with mininal changes to the existing driver, we
just let the alps driver not handle this device, then the trackpoint.c
will be the driver of this device if the trackpoint driver is enabled.
(if not, this device will fallback to a bare PS/2 device)
With the trackpoint.c, this trackpoint and 3 buttons all work well,
they have all features that the trackpoint should have, like
scrolling-screen, drag-and-drop and frame-selection.
Signed-off-by: XiaoXiao Liu <sliuuxiaonxiao@gmail.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a017fd82c upstream.
The GTCO tablet input driver configures itself from an HID report sent
via USB during the initial enumeration process. Some debugging messages
are generated during the parsing. A debugging message indentation
counter is not bounds checked, leading to the ability for a specially
crafted HID report to cause '-' and null bytes be written past the end
of the indentation array. As long as the kernel has CONFIG_DYNAMIC_DEBUG
enabled, this code will not be optimized out. This was discovered
during code review after a previous syzkaller bug was found in this
driver.
Signed-off-by: Grant Hernandez <granthernandez@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f54d801dda upstream.
Commit 9baf30972b ("bcache: fix for gc and write-back race") added a
new work queue dc->writeback_write_wq, but forgot to destroy it in the
error condition when creating dc->writeback_thread failed.
This patch destroys dc->writeback_write_wq if kthread_create() returns
error pointer to dc->writeback_thread, then a memory leak is avoided.
Fixes: 9baf30972b ("bcache: fix for gc and write-back race")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5461999848 upstream.
In bch_cached_dev_files[] from driver/md/bcache/sysfs.c, sysfs_errors is
incorrectly inserted in. The correct entry should be sysfs_io_errors.
This patch fixes the problem and now I/O errors of cached device can be
read from /sys/block/bcache<N>/bcache/io_errors.
Fixes: c7b7bd0740 ("bcache: add io_disable to struct cached_dev")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 578df99b1b upstream.
When md raid device (e.g. raid456) is used as backing device, read-ahead
requests on a degrading and recovering md raid device might be failured
immediately by md raid code, but indeed this md raid array can still be
read or write for normal I/O requests. Therefore such failed read-ahead
request are not real hardware failure. Further more, after degrading and
recovering accomplished, read-ahead requests will be handled by md raid
array again.
For such condition, I/O failures of read-ahead requests don't indicate
real health status (because normal I/O still be served), they should not
be counted into I/O error counter dc->io_errors.
Since there is no simple way to detect whether the backing divice is a
md raid device, this patch simply ignores I/O failures for read-ahead
bios on backing device, to avoid bogus backing device failure on a
degrading md raid array.
Suggested-and-tested-by: Thorsten Knabe <linux@thorsten-knabe.de>
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 249a5f6da5 upstream.
This reverts commit c4dc2497d5.
This patch enlarges a race between normal btree flush code path and
flush_btree_write(), which causes deadlock when journal space is
exhausted. Reverts this patch makes the race window from 128 btree
nodes to only 1 btree nodes.
Fixes: c4dc2497d5 ("bcache: fix high CPU occupancy during journal")
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Cc: Tang Junhui <tang.junhui.linux@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 695277f16b upstream.
This reverts commit 6147305c73.
Although this patch helps the failed bcache device to stop faster when
too many I/O errors detected on corresponding cached device, setting
CACHE_SET_IO_DISABLE bit to cache set c->flags was not a good idea. This
operation will disable all I/Os on cache set, which means other attached
bcache devices won't work neither.
Without this patch, the failed bcache device can also be stopped
eventually if internal I/O accomplished (e.g. writeback). Therefore here
I revert it.
Fixes: 6147305c73 ("bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error()")
Reported-by: Yong Li <mr.liyong@qq.com>
Signed-off-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e833dc36 upstream.
The AES GCM function reuses an 'op' data structure, which members
contain values that must be cleared for each (re)use.
This fix resolves a crypto self-test failure:
alg: aead: gcm-aes-ccp encryption test failed (wrong result) on test vector 2, cfg="two even aligned splits"
Fixes: 36cf515b9b ("crypto: ccp - Enable support for AES GCM on v5 CCPs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f7a813740 upstream.
The hardware automatically zero pads incomplete block ciphers
blocks without raising any errors. This is a screw-up. This
was noticed by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS tests that
sent a incomplete blocks and expect them to fail.
This fixes:
cbc-aes-ppc4xx encryption unexpectedly succeeded on test vector
"random: len=2409 klen=32"; expected_error=-22, cfg="random:
may_sleep use_digest src_divs=[96.90%@+2295, 2.34%@+4066,
0.32%@alignmask+12, 0.34%@+4087, 0.9%@alignmask+1787, 0.1%@+3767]
iv_offset=6"
ecb-aes-ppc4xx encryption unexpectedly succeeded on test vector
"random: len=1011 klen=32"; expected_error=-22, cfg="random:
may_sleep use_digest src_divs=[100.0%@alignmask+20]
dst_divs=[3.12%@+3001, 96.88%@+4070]"
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: stable@vger.kernel.org [4.19, 5.0 and 5.1]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70c4997f34 upstream.
While the hardware consider them to be blockciphers, the
reference implementation defines them as streamciphers.
Do the right thing and set the blocksize to 1. This
was found by CONFIG_CRYPTO_MANAGER_EXTRA_TESTS.
This fixes the following issues:
skcipher: blocksize for ofb-aes-ppc4xx (16) doesn't match generic impl (1)
skcipher: blocksize for cfb-aes-ppc4xx (16) doesn't match generic impl (1)
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: stable@vger.kernel.org
Fixes: f2a13e7cba ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfa2ba7d9e upstream.
This patch fixes a issue with crypto4xx's ctr(aes) that was
discovered by libcapi's kcapi-enc-test.sh test.
The some of the ctr(aes) encryptions test were failing on the
non-power-of-two test:
kcapi-enc - Error: encryption failed with error 0
kcapi-enc - Error: decryption failed with error 0
[FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits):
original file (1d100e..cc96184c) and generated file (e3b0c442..1b7852b855)
[FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits)
(openssl generated CT): original file (e3b0..5) and generated file (3..8e)
[PASSED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (128 bits)
(openssl generated PT)
[FAILED: 32-bit - 5.1.0-rc1+] 15 bytes: STDIN / STDOUT enc test (password):
original file (1d1..84c) and generated file (e3b..852b855)
But the 16, 32, 512, 65536 tests always worked.
Thankfully, this isn't a hidden hardware problem like previously,
instead this turned out to be a copy and paste issue.
With this patch, all the tests are passing with and
kcapi-enc-test.sh gives crypto4xx's a clean bill of health:
"Number of failures: 0" :).
Cc: stable@vger.kernel.org
Fixes: 98e87e3d93 ("crypto: crypto4xx - add aes-ctr support")
Fixes: f2a13e7cba ("crypto: crypto4xx - enable AES RFC3686, ECB, CFB and OFB offloads")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7545b6c208 upstream.
Clear the CRYPTO_TFM_REQ_MAY_SLEEP flag when the chacha20poly1305
operation is being continued from an async completion callback, since
sleeping may not be allowed in that context.
This is basically the same bug that was recently fixed in the xts and
lrw templates. But, it's always been broken in chacha20poly1305 too.
This was found using syzkaller in combination with the updated crypto
self-tests which actually test the MAY_SLEEP flag now.
Reproducer:
python -c 'import socket; socket.socket(socket.AF_ALG, 5, 0).bind(
("aead", "rfc7539(cryptd(chacha20-generic),poly1305-generic)"))'
Kernel output:
BUG: sleeping function called from invalid context at include/crypto/algapi.h:426
in_atomic(): 1, irqs_disabled(): 0, pid: 1001, name: kworker/2:2
[...]
CPU: 2 PID: 1001 Comm: kworker/2:2 Not tainted 5.2.0-rc2 #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-20181126_142135-anatol 04/01/2014
Workqueue: crypto cryptd_queue_worker
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x4d/0x6a lib/dump_stack.c:113
___might_sleep kernel/sched/core.c:6138 [inline]
___might_sleep.cold.19+0x8e/0x9f kernel/sched/core.c:6095
crypto_yield include/crypto/algapi.h:426 [inline]
crypto_hash_walk_done+0xd6/0x100 crypto/ahash.c:113
shash_ahash_update+0x41/0x60 crypto/shash.c:251
shash_async_update+0xd/0x10 crypto/shash.c:260
crypto_ahash_update include/crypto/hash.h:539 [inline]
poly_setkey+0xf6/0x130 crypto/chacha20poly1305.c:337
poly_init+0x51/0x60 crypto/chacha20poly1305.c:364
async_done_continue crypto/chacha20poly1305.c:78 [inline]
poly_genkey_done+0x15/0x30 crypto/chacha20poly1305.c:369
cryptd_skcipher_complete+0x29/0x70 crypto/cryptd.c:279
cryptd_skcipher_decrypt+0xcd/0x110 crypto/cryptd.c:339
cryptd_queue_worker+0x70/0xa0 crypto/cryptd.c:184
process_one_work+0x1ed/0x420 kernel/workqueue.c:2269
worker_thread+0x3e/0x3a0 kernel/workqueue.c:2415
kthread+0x11f/0x140 kernel/kthread.c:255
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Fixes: 71ebc4d1b2 ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539")
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Martin Willi <martin@strongswan.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bd934de1e upstream.
The sha256-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: the actual digest, result: initial
value of SHA internal state. The error is in sha256_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha2_ce_transform to make the final round. However, in
sha256_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 03802f6a80 ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d4aaf16de upstream.
The sha1-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: da39a3ee..., result: 67452301...
(initial value of SHA internal state). The error is in sha1_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha1_ce_transform to make the final round. However, in
sha1_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 07eb54d306 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c6bc4dfa5 upstream.
Changing ghash_mod_init() to be subsys_initcall made it start running
before the alignment fault handler has been installed on ARM. In kernel
builds where the keys in the ghash test vectors happened to be
misaligned in the kernel image, this exposed the longstanding bug that
ghash_setkey() is incorrectly casting the key buffer (which can have any
alignment) to be128 for passing to gf128mul_init_4k_lle().
Fix this by memcpy()ing the key to a temporary buffer.
Don't fix it by setting an alignmask on the algorithm instead because
that would unnecessarily force alignment of the data too.
Fixes: 2cdc6899a8 ("crypto: ghash - Add GHASH digest algorithm for GCM")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78ff751f8e upstream.
A system bus error during a PDMA transfer can mess up the calculation of
the transfer residual (the PDMA handshaking hardware lacks a byte
counter). This results in data corruption.
The algorithm in this patch anticipates a bus error by starting each
transfer with a MOVE.B instruction. If a bus error is caught the transfer
will be retried. If a bus error is caught later in the transfer (for a
MOVE.W instruction) the transfer gets failed and subsequent requests for
that target will use PIO instead of PDMA.
This avoids the "!REQ and !ACK" error so the severity level of that message
is reduced to KERN_DEBUG.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reported-by: Chris Jones <chris@martin-jones.com>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7398cee4c3 upstream.
Some targets introduce delays when handshaking the response to certain
commands. For example, a disk may send a 96-byte response to an INQUIRY
command (or a 24-byte response to a MODE SENSE command) too slowly.
Apparently the first 12 or 14 bytes are handshaked okay but then the system
bus error timeout is reached while transferring the next word.
Since the scsi bus phase hasn't changed, the driver then sets the target
borken flag to prevent further PDMA transfers. The driver also logs the
warning, "switching to slow handshake".
Raise the PDMA threshold to 512 bytes so that PIO transfers will be used
for these commands. This default is sufficiently low that PDMA will still
be used for READ and WRITE commands.
The existing threshold (16 bytes) was chosen more or less at random.
However, best performance requires the threshold to be as low as possible.
Those systems that don't need the PIO workaround at all may benefit from
mac_scsi.setup_use_pdma=1
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.14+
Fixes: 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8f96df5b8 upstream.
In megasas_get_target_prop(), driver is incorrectly calculating the target
ID for devices with channel 1 and 3. Due to this, firmware will either
fail the command (if there is no device with the target id sent from
driver) or could return the properties for a target which was not
intended. Devices could end up with the wrong queue depth due to this.
Fix target id calculation for channel 1 and 3.
Fixes: 96188a89cc ("scsi: megaraid_sas: NVME interface target prop added")
Cc: stable@vger.kernel.org
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9b0530fa0 upstream.
When scsi_init_sense_cache(host) is called concurrently from different
hosts, each code path may find that no cache has been created and
allocate a new one. The lack of locking can lead to potentially
overriding a cache allocated by a different host.
Fix the issue by moving 'mutex_lock(&scsi_sense_cache_mutex)' before
scsi_select_sense_cache().
Fixes: 0a6ac4ee7c ("scsi: respect unchecked_isa_dma for blk-mq")
Cc: Stable <stable@vger.kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25fcf94a2f upstream.
This reverts commit 4822827a69.
The purpose of that commit was to suppress a timeout warning message which
appeared to be caused by target latency. But suppressing the warning is
undesirable as the warning may indicate a messed up transfer count.
Another problem with that commit is that 15 ms is too long to keep
interrupts disabled as interrupt latency can cause system clock drift and
other problems.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 4822827a69 ("scsi: ncr5380: Increase register polling limit")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57f3132651 upstream.
The reselection interrupt gets disabled during selection and must be
re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a
disconnected command may time-out or the target may wedge the bus while
trying to reselect the host. This can happen after a command is aborted.
Fix this by enabling the reselection interrupt in NCR5380_main() after
calls to NCR5380_select() and NCR5380_information_transfer() return.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.9+
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1078e821b upstream.
Instead of trying to allocate pages with GFP_USER in
add_ballooned_pages() check the available free memory via
si_mem_available(). GFP_USER is far less limiting memory exhaustion
than the test via si_mem_available().
This will avoid dom0 running out of memory due to excessive foreign
page mappings especially on ARM and on x86 in PVH mode, as those don't
have a pre-ballooned area which can be used for foreign mappings.
As the normal ballooning suffers from the same problem don't balloon
down more than si_mem_available() pages in one iteration. At the same
time limit the default maximum number of retries.
This is part of XSA-300.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da99466ac2 ]
This fixes a global out-of-bounds read access in the copy_buffer
function of the floppy driver.
The FDDEFPRM ioctl allows one to set the geometry of a disk. The sect
and head fields (unsigned int) of the floppy_drive structure are used to
compute the max_sector (int) in the make_raw_rw_request function. It is
possible to overflow the max_sector. Next, max_sector is passed to the
copy_buffer function and used in one of the memcpy calls.
An unprivileged user could trigger the bug if the device is accessible,
but requires a floppy disk to be inserted.
The patch adds the check for the .sect * .head multiplication for not
overflowing in the set_geometry function.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b04609b78 ]
This fixes the invalid pointer dereference in the drive_name function of
the floppy driver.
The native_format field of the struct floppy_drive_params is used as
floppy_type array index in the drive_name function. Thus, the field
should be checked the same way as the autodetect field.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. Next, FDGETDRVTYP ioctl should
be used to call the drive_name. A floppy disk is not required to be
inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for a value of the native_format field to be in
the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array
indices.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5635f897ed ]
This fixes a global out-of-bounds read access in the next_valid_format
function of the floppy driver.
The values from autodetect field of the struct floppy_drive_params are
used as indices for the floppy_type array in the next_valid_format
function 'floppy_type[DP->autodetect[probed_format]].sect'.
To trigger the bug, one could use a value out of range and set the drive
parameters with the FDSETDRVPRM ioctl. A floppy disk is not required to
be inserted.
CAP_SYS_ADMIN is required to call FDSETDRVPRM.
The patch adds the check for values of the autodetect field to be in the
'0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3554aeb99 ]
This fixes a divide by zero error in the setup_format_params function of
the floppy driver.
Two consecutive ioctls can trigger the bug: The first one should set the
drive geometry with such .sect and .rate values for the F_SECT_PER_TRACK
to become zero. Next, the floppy format operation should be called.
A floppy disk is not required to be inserted. An unprivileged user
could trigger the bug if the device is accessible.
The patch checks F_SECT_PER_TRACK for a non-zero value in the
set_geometry function. The proper check should involve a reasonable
upper limit for the .sect and .rate fields, but it could change the
UAPI.
The patch also checks F_SECT_PER_TRACK in the setup_format_params, and
cancels the formatting operation in case of zero.
The bug was found by syzkaller.
Signed-off-by: Denis Efremov <efremov@ispras.ru>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe06a5128 ]
A recent commit efa14c3985 ("iavf: allow null RX descriptors") added
a null pointer sanity check on rx_buffer, however, rx_buffer is being
dereferenced before that check, which implies a null pointer dereference
bug can potentially occur. Fix this by only dereferencing rx_buffer
until after the null pointer check.
Addresses-Coverity: ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 433a06d7d7 ]
Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1788b8569f ]
gtp_encap_destroy() is called twice.
1. When interface is deleted.
2. When udp socket is destroyed.
either gtp->sk0 or gtp->sk1u could be freed by sock_put() in
gtp_encap_destroy(). so, when gtp_encap_destroy() is called again,
it would uses freed sk pointer.
patch makes gtp_encap_destroy() to set either gtp->sk0 or gtp->sk1u to
null. in addition, both gtp->sk0 and gtp->sk1u pointer are protected
by rtnl_lock. so, rtnl_lock() is added.
Test command:
gtp-link add gtp1 &
killall gtp-link
ip link del gtp1
Splat looks like:
[ 83.182767] BUG: KASAN: use-after-free in __lock_acquire+0x3a20/0x46a0
[ 83.184128] Read of size 8 at addr ffff8880cc7d5360 by task ip/1008
[ 83.185567] CPU: 1 PID: 1008 Comm: ip Not tainted 5.2.0-rc6+ #50
[ 83.188469] Call Trace:
[ ... ]
[ 83.200126] lock_acquire+0x141/0x380
[ 83.200575] ? lock_sock_nested+0x3a/0xf0
[ 83.201069] _raw_spin_lock_bh+0x38/0x70
[ 83.201551] ? lock_sock_nested+0x3a/0xf0
[ 83.202044] lock_sock_nested+0x3a/0xf0
[ 83.202520] gtp_encap_destroy+0x18/0xe0 [gtp]
[ 83.203065] gtp_encap_disable.isra.14+0x13/0x50 [gtp]
[ 83.203687] gtp_dellink+0x56/0x170 [gtp]
[ 83.204190] rtnl_delete_link+0xb4/0x100
[ ... ]
[ 83.236513] Allocated by task 976:
[ 83.236925] save_stack+0x19/0x80
[ 83.237332] __kasan_kmalloc.constprop.3+0xa0/0xd0
[ 83.237894] kmem_cache_alloc+0xd8/0x280
[ 83.238360] sk_prot_alloc.isra.42+0x50/0x200
[ 83.238874] sk_alloc+0x32/0x940
[ 83.239264] inet_create+0x283/0xc20
[ 83.239684] __sock_create+0x2dd/0x540
[ 83.240136] __sys_socket+0xca/0x1a0
[ 83.240550] __x64_sys_socket+0x6f/0xb0
[ 83.240998] do_syscall_64+0x9c/0x450
[ 83.241466] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 83.242061]
[ 83.242249] Freed by task 0:
[ 83.242616] save_stack+0x19/0x80
[ 83.243013] __kasan_slab_free+0x111/0x150
[ 83.243498] kmem_cache_free+0x89/0x250
[ 83.244444] __sk_destruct+0x38f/0x5a0
[ 83.245366] rcu_core+0x7e9/0x1c20
[ 83.245766] __do_softirq+0x213/0x8fa
Fixes: 1e3a3abd8b ("gtp: make GTP sockets in gtp_newlink optional")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c49a8682fc ]
Problem: The Linux Bluetooth stack yields complete control over the BLE
connection interval to the remote device.
The Linux Bluetooth stack provides access to the BLE connection interval
min and max values through /sys/kernel/debug/bluetooth/hci0/
conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval.
These values are used for initial BLE connections, but the remote device
has the ability to request a connection parameter update. In the event
that the remote side requests to change the connection interval, the Linux
kernel currently only validates that the desired value is within the
acceptable range in the Bluetooth specification (6 - 3200, corresponding to
7.5ms - 4000ms). There is currently no validation that the desired value
requested by the remote device is within the min/max limits specified in
the conn_min_interval/conn_max_interval configurations. This essentially
leads to Linux yielding complete control over the connection interval to
the remote device.
The proposed patch adds a verification step to the connection parameter
update mechanism, ensuring that the desired value is within the min/max
bounds of the current connection. If the desired value is outside of the
current connection min/max values, then the connection parameter update
request is rejected and the negative response is returned to the remote
device. Recall that the initial connection is established using the local
conn_min_interval/conn_max_interval values, so this allows the Linux
administrator to retain control over the BLE connection interval.
The one downside that I see is that the current default Linux values for
conn_min_interval and conn_max_interval typically correspond to 30ms and
50ms respectively. If this change were accepted, then it is feasible that
some devices would no longer be able to negotiate to their desired
connection interval values. This might be remedied by setting the default
Linux conn_min_interval and conn_max_interval values to the widest
supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same
behavior as the current implementation, where the remote device could
request to change the connection interval value to any value that is
permitted by the Bluetooth specification, and Linux would accept the
desired value.
Signed-off-by: Carey Sonsino <csonsino@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e30155fd23 ]
If an invalid role is sent from user space, gtp_encap_enable() will fail.
Then, it should call gtp_encap_disable_sock() but current code doesn't.
It makes memory leak.
Fixes: 91ed81f9ab ("gtp: support SGSN-side tunnels")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bff5a556c1 ]
'probe libc's inet_pton & backtrace it with ping' testcase sometimes
fails on powerpc because distro ping binary does not have symbol
information and thus it prints "[unknown]" function name in the
backtrace.
Accept "[unknown]" as valid function name for powerpc as well.
# perf test -v "probe libc's inet_pton & backtrace it with ping"
Before:
59: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 79695
ping 79718 [077] 96483.787025: probe_libc:inet_pton: (7fff83a754c8)
7fff83a754c8 __GI___inet_pton+0x8 (/usr/lib64/power9/libc-2.28.so)
7fff83a2b7a0 gaih_inet.constprop.7+0x1020
(/usr/lib64/power9/libc-2.28.so)
7fff83a2c170 getaddrinfo+0x160 (/usr/lib64/power9/libc-2.28.so)
1171830f4 [unknown] (/usr/bin/ping)
FAIL: expected backtrace entry
".*\+0x[[:xdigit:]]+[[:space:]]\(.*/bin/ping.*\)$"
got "1171830f4 [unknown] (/usr/bin/ping)"
test child finished with -1
---- end ----
probe libc's inet_pton & backtrace it with ping: FAILED!
After:
59: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 79085
ping 79108 [045] 96400.214177: probe_libc:inet_pton: (7fffbb9654c8)
7fffbb9654c8 __GI___inet_pton+0x8 (/usr/lib64/power9/libc-2.28.so)
7fffbb91b7a0 gaih_inet.constprop.7+0x1020
(/usr/lib64/power9/libc-2.28.so)
7fffbb91c170 getaddrinfo+0x160 (/usr/lib64/power9/libc-2.28.so)
132e830f4 [unknown] (/usr/bin/ping)
test child finished with 0
---- end ----
probe libc's inet_pton & backtrace it with ping: Ok
Signed-off-by: Seeteena Thoufeek <s1seetee@linux.vnet.ibm.com>
Reviewed-by: Kim Phillips <kim.phillips@amd.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Fixes: 1632936480 ("perf tests: Fix record+probe_libc_inet_pton.sh without ping's debuginfo")
Link: http://lkml.kernel.org/r/1561630614-3216-1-git-send-email-s1seetee@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b188b03270 ]
Handle overlooked case where the target address is assigned to a peer
and neither route nor gateway exist.
For one peer, no checks are performed to see if it is meant to receive
packets for a given address.
As soon as there is a second peer however, checks are performed
to deal with routes and gateways for handling complex setups with
multiple hops to a target address.
This logic assumed that no route and no gateway imply that the
destination address can not be reached, which is false in case of a
direct peer.
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Tested-by: Michael Scott <mike@foundries.io>
Signed-off-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa52bcbe0e ]
Michael reported crash with by bpf program in json mode on powerpc:
# bpftool prog -p dump jited id 14
[{
"name": "0xd00000000a9aa760",
"insns": [{
"pc": "0x0",
"operation": "nop",
"operands": [null
]
},{
"pc": "0x4",
"operation": "nop",
"operands": [null
]
},{
"pc": "0x8",
"operation": "mflr",
Segmentation fault (core dumped)
The code is assuming char pointers in format, which is not always
true at least for powerpc. Fixing this by dumping the whole string
into buffer based on its format.
Please note that libopcodes code does not check return values from
fprintf callback, but as per Jakub suggestion returning -1 on allocation
failure so we do the best effort to propagate the error.
Fixes: 107f041212 ("tools: bpftool: add JSON output for `bpftool prog dump jited *` command")
Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
