commit 0a55f4ab96 upstream.
Normally when the MMC core sees an "-EILSEQ" error returned by a host
controller then it will trigger a retuning of the card. This is
generally a good idea.
However, if a command is expected to sometimes cause transfer errors
then these transfer errors shouldn't cause a re-tuning. This
re-tuning will be a needless waste of time. One example case where a
transfer is expected to cause errors is when transitioning between
idle (sometimes referred to as "sleep" in Broadcom code) and active
state on certain Broadcom WiFi SDIO cards. Specifically if the card
was already transitioning between states when the command was sent it
could cause an error on the SDIO bus.
Let's add an API that the SDIO function drivers can call that will
temporarily disable the auto-tuning functionality. Then we can add a
call to this in the Broadcom WiFi driver and any other driver that
might have similar needs.
NOTE: this makes the assumption that the card is already tuned well
enough that it's OK to disable the auto-retuning during one of these
error-prone situations. Presumably the driver code performing the
error-prone transfer knows how to recover / retry from errors. ...and
after we can get back to a state where transfers are no longer
error-prone then we can enable the auto-retuning again. If we truly
find ourselves in a case where the card needs to be retuned sometimes
to handle one of these error-prone transfers then we can always try a
few transfers first without auto-retuning and then re-try with
auto-retuning if the first few fail.
Without this change on rk3288-veyron-minnie I periodically see this in
the logs of a machine just sitting there idle:
dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f7b79a44e upstream.
The O2Micro controller only supports tuning at 4-bits. So the host driver
needs to change the bus width while tuning and then set it back when done.
There was a bug in the original implementation in that mmc->ios.bus_width
also wasn't updated. Thus setting the incorrect blocksize in
sdhci_send_tuning which results in a tuning failure.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Fixes: 0086fc217d ("mmc: sdhci: Add support for O2 hardware tuning")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 159491f3b5 ]
The inline assembler functions ap_aqic() and ap_qact() used two
variables declared on the very same register. One variable was for
input only, the other for output. Looks like newer versions of the gcc
don't like this. Anyway it is a better coding to use one variable
(which may have a union data type) on one register for input and
output. So this patch introduces unions and uses only one variable now
for input and output for GR1 for the PQAP(QACT) and PQAP(QIC)
invocation.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 146448524b ]
[heiko.carstens@de.ibm.com]:
-----
Laura Abbott reported that the kernel doesn't build anymore with gcc 9,
due to the "X" constraint. Ilya provided the gcc 9 patch "S/390:
Introduce jdd constraint" which introduces the new "jdd" constraint
which fixes this.
-----
The support for section anchors on S/390 introduced in gcc9 has changed
the behavior of "X" constraint, which can now produce register
references. Since existing constraints, in particular, "i", do not fit
the intended use case on S/390, the new machine-specific "jdd"
constraint was introduced. This patch makes jump labels use "jdd"
constraint when building with gcc9.
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1dac6f5b0e ]
gcc gets a bit confused by the logic in ovl_setup_trap() and
can't figure out whether the local 'trap' variable in the caller
was initialized or not:
fs/overlayfs/super.c: In function 'ovl_fill_super':
fs/overlayfs/super.c:1333:4: error: 'trap' may be used uninitialized in this function [-Werror=maybe-uninitialized]
iput(trap);
^~~~~~~~~~
fs/overlayfs/super.c:1312:17: note: 'trap' was declared here
Reword slightly to make it easier for the compiler to understand.
Fixes: 146d62e5a5 ("ovl: detect overlapping layers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9179c21dc6 ]
NFS mounts can be disconnected from fs root. Don't fail the overlapping
layer check because of this.
The check is not authoritative anyway, since topology can change during or
after the check.
Reported-by: Antti Antinoja <antti@fennosys.fi>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 146d62e5a5 ("ovl: detect overlapping layers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 146d62e5a5 ]
Overlapping overlay layers are not supported and can cause unexpected
behavior, but overlayfs does not currently check or warn about these
configurations.
User is not supposed to specify the same directory for upper and
lower dirs or for different lower layers and user is not supposed to
specify directories that are descendants of each other for overlay
layers, but that is exactly what this zysbot repro did:
https://syzkaller.appspot.com/x/repro.syz?x=12c7a94f400000
Moving layer root directories into other layers while overlayfs
is mounted could also result in unexpected behavior.
This commit places "traps" in the overlay inode hash table.
Those traps are dummy overlay inodes that are hashed by the layers
root inodes.
On mount, the hash table trap entries are used to verify that overlay
layers are not overlapping. While at it, we also verify that overlay
layers are not overlapping with directories "in-use" by other overlay
instances as upperdir/workdir.
On lookup, the trap entries are used to verify that overlay layers
root inodes have not been moved into other layers after mount.
Some examples:
$ ./run --ov --samefs -s
...
( mkdir -p base/upper/0/u base/upper/0/w base/lower lower upper mnt
mount -o bind base/lower lower
mount -o bind base/upper upper
mount -t overlay none mnt ...
-o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w)
$ umount mnt
$ mount -t overlay none mnt ...
-o lowerdir=base,upperdir=upper/0/u,workdir=upper/0/w
[ 94.434900] overlayfs: overlapping upperdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=upper/0/u,upperdir=upper/0/u,workdir=upper/0/w
[ 151.350132] overlayfs: conflicting lowerdir path
mount: none is already mounted or mnt busy
$ mount -t overlay none mnt ...
-o lowerdir=lower:lower/a,upperdir=upper/0/u,workdir=upper/0/w
[ 201.205045] overlayfs: overlapping lowerdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w
$ mv base/upper/0/ base/lower/
$ find mnt/0
mnt/0
mnt/0/w
find: 'mnt/0/w/work': Too many levels of symbolic links
find: 'mnt/0/u': Too many levels of symbolic links
Reported-by: syzbot+9c69c282adc4edd2b540@syzkaller.appspotmail.com
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dde1e42f4 ]
Relax the condition that overlayfs supports nfs export, to require
that i_ino is consistent with st_ino/d_ino.
It is enough to require that st_ino and d_ino are consistent.
This fixes the failure of xfstest generic/504, due to mismatch of
st_ino to inode number in the output of /proc/locks.
Fixes: 12574a9f4c ("ovl: consistent i_ino for non-samefs with xino")
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 941d935ac7 ]
The ioctl argument was parsed as the wrong type.
Fixes: b21d9c435f ("ovl: support the FS_IOC_FS[SG]ETXATTR ioctls")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b21d9c435f ]
They are the extended version of FS_IOC_FS[SG]ETFLAGS ioctls.
xfs_io -c "chattr <flags>" uses the new ioctls for setting flags.
This used to work in kernel pre v4.19, before stacked file ops
introduced the ovl_ioctl whitelist.
Reported-by: Dave Chinner <david@fromorbit.com>
Fixes: d1d04ef857 ("ovl: stack file ops")
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f303d6053 upstream.
We already did this for clang, but now gcc has that warning too. Yes,
yes, the address may be unaligned. And that's kind of the point.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a60aa05a0 upstream.
Add support for processing switch jump tables in objects with multiple
.rodata sections, such as those created by '-ffunction-sections' and
'-fdata-sections'. Currently, objtool always looks in .rodata for jump
table information, which results in many "sibling call from callable
instruction with modified stack frame" warnings with objects compiled
using those flags.
The fix is comprised of three parts:
1. Flagging all .rodata sections when importing ELF information for
easier checking later.
2. Keeping a reference to the section each relocation is from in order
to get the list_head for the other relocations in that section.
3. Finding jump tables by following relocations to .rodata sections,
rather than always referencing a single global .rodata section.
The patch has been tested without data sections enabled and no
differences in the resulting orc unwind information were seen.
Note that as objtool adds terminators to end of each .text section the
unwind information generated between a function+data sections build and
a normal build aren't directly comparable. Manual inspection suggests
that objtool is now generating the correct information, or at least
making more of an effort to do so than it did previously.
Signed-off-by: Allan Xavier <allan.x.xavier@oracle.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/099bdc375195c490dda04db777ee0b95d566ded1.1536325914.git.jpoimboe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c97bf863e upstream.
Starting with GCC 9, -Warray-bounds detects cases when memset is called
starting on a member of a struct but the size to be cleared ends up
writing over further members.
Such a call happens in the trace code to clear, at once, all members
after and including `seq` on struct trace_iterator:
In function 'memset',
inlined from 'ftrace_dump' at kernel/trace/trace.c:8914:3:
./include/linux/string.h:344:9: warning: '__builtin_memset' offset
[8505, 8560] from the object at 'iter' is out of the bounds of
referenced subobject 'seq' with type 'struct trace_seq' at offset
4368 [-Warray-bounds]
344 | return __builtin_memset(p, c, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
In order to avoid GCC complaining about it, we compute the address
ourselves by adding the offsetof distance instead of referring
directly to the member.
Since there are two places doing this clear (trace.c and trace_kdb.c),
take the chance to move the workaround into a single place in
the internal header.
Link: http://lkml.kernel.org/r/20190523124535.GA12931@gmail.com
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
[ Removed unnecessary parenthesis around "iter" ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6653b3629 upstream.
tcp_fragment() might be called for skbs in the write queue.
Memory limits might have been exceeded because tcp_sendmsg() only
checks limits at full skb (64KB) boundaries.
Therefore, we need to make sure tcp_fragment() wont punish applications
that might have setup very low SO_SNDBUF values.
Fixes: f070ef2ac6 ("tcp: tcp_fragment() should apply sane memory limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f69e749a49 upstream.
file_remove_privs() might be called for non-regular files, e.g.
blkdev inode. There is no reason to do its job on things
like blkdev inodes, pipes, or cdevs. Hence, abort if
file does not refer to a regular inode.
AV: more to the point, for devices there might be any number of
inodes refering to given device. Which one to strip the permissions
from, even if that made any sense in the first place? All of them
will be observed with contents modified, after all.
Found by LockDoc (Alexander Lochmann, Horst Schirmeier and Olaf
Spinczyk)
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Alexander Lochmann <alexander.lochmann@tu-dortmund.de>
Signed-off-by: Horst Schirmeier <horst.schirmeier@tu-dortmund.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59ea6d06cf upstream.
When fixing the race conditions between the coredump and the mmap_sem
holders outside the context of the process, we focused on
mmget_not_zero()/get_task_mm() callers in 04f5866e41 ("coredump: fix
race condition between mmget_not_zero()/get_task_mm() and core
dumping"), but those aren't the only cases where the mmap_sem can be
taken outside of the context of the process as Michal Hocko noticed
while backporting that commit to older -stable kernels.
If mmgrab() is called in the context of the process, but then the
mm_count reference is transferred outside the context of the process,
that can also be a problem if the mmap_sem has to be taken for writing
through that mm_count reference.
khugepaged registration calls mmgrab() in the context of the process,
but the mmap_sem for writing is taken later in the context of the
khugepaged kernel thread.
collapse_huge_page() after taking the mmap_sem for writing doesn't
modify any vma, so it's not obvious that it could cause a problem to the
coredump, but it happens to modify the pmd in a way that breaks an
invariant that pmd_trans_huge_lock() relies upon. collapse_huge_page()
needs the mmap_sem for writing just to block concurrent page faults that
call pmd_trans_huge_lock().
Specifically the invariant that "!pmd_trans_huge()" cannot become a
"pmd_trans_huge()" doesn't hold while collapse_huge_page() runs.
The coredump will call __get_user_pages() without mmap_sem for reading,
which eventually can invoke a lockless page fault which will need a
functional pmd_trans_huge_lock().
So collapse_huge_page() needs to use mmget_still_valid() to check it's
not running concurrently with the coredump... as long as the coredump
can invoke page faults without holding the mmap_sem for reading.
This has "Fixes: khugepaged" to facilitate backporting, but in my view
it's more a bug in the coredump code that will eventually have to be
rewritten to stop invoking page faults without the mmap_sem for reading.
So the long term plan is still to drop all mmget_still_valid().
Link: http://lkml.kernel.org/r/20190607161558.32104-1-aarcange@redhat.com
Fixes: ba76149f47 ("thp: khugepaged")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 275e928f19 ]
Force of 56G is not supported by hardware in Ethernet devices. This
configuration fails with a bad parameter error from firmware.
Add check of this case. Instead of trying to set 56G with autoneg off,
return a meaningful error.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12e750bc62 ]
If alloc_workqueue fails in alua_init, it should return -ENOMEM, otherwise
it will trigger null-ptr-deref while unloading module which calls
destroy_workqueue dereference
wq->lock like this:
BUG: KASAN: null-ptr-deref in __lock_acquire+0x6b4/0x1ee0
Read of size 8 at addr 0000000000000080 by task syz-executor.0/7045
CPU: 0 PID: 7045 Comm: syz-executor.0 Tainted: G C 5.1.0+ #28
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1
Call Trace:
dump_stack+0xa9/0x10e
__kasan_report+0x171/0x18d
? __lock_acquire+0x6b4/0x1ee0
kasan_report+0xe/0x20
__lock_acquire+0x6b4/0x1ee0
lock_acquire+0xb4/0x1b0
__mutex_lock+0xd8/0xb90
drain_workqueue+0x25/0x290
destroy_workqueue+0x1f/0x3f0
__x64_sys_delete_module+0x244/0x330
do_syscall_64+0x72/0x2a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 03197b61c5 ("scsi_dh_alua: Use workqueue for RTPG")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d94f06e7f ]
When SME is enabled, the smartpqi driver won't work on the HP DL385 G10
machine, which causes the failure of kernel boot because it fails to
allocate pqi error buffer. Please refer to the kernel log:
....
[ 9.431749] usbcore: registered new interface driver uas
[ 9.441524] Microsemi PQI Driver (v1.1.4-130)
[ 9.442956] i40e 0000:04:00.0: fw 6.70.48768 api 1.7 nvm 10.2.5
[ 9.447237] smartpqi 0000:23:00.0: Microsemi Smart Family Controller found
Starting dracut initqueue hook...
[ OK ] Started Show Plymouth Boot Scre[ 9.471654] Broadcom NetXtreme-C/E driver bnxt_en v1.9.1
en.
[ OK ] Started Forward Password Requests to Plymouth Directory Watch.
[[0;[ 9.487108] smartpqi 0000:23:00.0: failed to allocate PQI error buffer
....
[ 139.050544] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 139.589779] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
Basically, the fact that the coherent DMA mask value wasn't set caused the
driver to fall back to SWIOTLB when SME is active.
For correct operation, lets call the dma_set_mask_and_coherent() to
properly set the mask for both streaming and coherent, in order to inform
the kernel about the devices DMA addressing capabilities.
Signed-off-by: Lianbo Jiang <lijiang@redhat.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c678726305 ]
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 315ca92dd8 ]
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e29ab3186 ]
Calling sys_ni_syscall through a syscall_fn_t pointer trips indirect
call Control-Flow Integrity checking due to a function type
mismatch. Use SYSCALL_DEFINE0 for __arm64_sys_ni_syscall instead and
remove the now unnecessary casts.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e358bd7b7 ]
Although a syscall defined using SYSCALL_DEFINE0 doesn't accept
parameters, use the correct function type to avoid indirect call
type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ef8f368ce ]
Syscall wrappers in <asm/syscall_wrapper.h> use const struct pt_regs *
as the argument type. Use const in syscall_fn_t as well to fix indirect
call type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a3f49364c ]
Currently the HV KVM code takes the kvm->lock around calls to
kvm_for_each_vcpu() and kvm_get_vcpu_by_id() (which can call
kvm_for_each_vcpu() internally). However, that leads to a lock
order inversion problem, because these are called in contexts where
the vcpu mutex is held, but the vcpu mutexes nest within kvm->lock
according to Documentation/virtual/kvm/locking.txt. Hence there
is a possibility of deadlock.
To fix this, we simply don't take the kvm->lock mutex around these
calls. This is safe because the implementations of kvm_for_each_vcpu()
and kvm_get_vcpu_by_id() have been designed to be able to be called
locklessly.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1659e27d2b ]
Currently the Book 3S KVM code uses kvm->lock to synchronize access
to the kvm->arch.rtas_tokens list. Because this list is scanned
inside kvmppc_rtas_hcall(), which is called with the vcpu mutex held,
taking kvm->lock cause a lock inversion problem, which could lead to
a deadlock.
To fix this, we add a new mutex, kvm->arch.rtas_token_lock, which nests
inside the vcpu mutexes, and use that instead of kvm->lock when
accessing the rtas token list.
This removes the lockdep_assert_held() in kvmppc_rtas_tokens_free().
At this point we don't hold the new mutex, but that is OK because
kvmppc_rtas_tokens_free() is only called when the whole VM is being
destroyed, and at that point nothing can be looking up a token in
the list.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10e0cc113 ]
During a suspend/resume, the xenwatch thread waits for all outstanding
xenstore requests and transactions to complete. This does not work
correctly for transactions started by userspace because it waits for
them to complete after freezing userspace threads which means the
transactions have no way of completing, resulting in a deadlock. This is
trivial to reproduce by running this script and then suspending the VM:
import pyxs, time
c = pyxs.client.Client(xen_bus_path="/dev/xen/xenbus")
c.connect()
c.transaction()
time.sleep(3600)
Even if this deadlock were resolved, misbehaving userspace should not
prevent a VM from being migrated. So, instead of waiting for these
transactions to complete before suspending, store the current generation
id for each transaction when it is started. The global generation id is
incremented during resume. If the caller commits the transaction and the
generation id does not match the current generation id, return EAGAIN so
that they try again. If the transaction was instead discarded, return OK
since no changes were made anyway.
This only affects users of the xenbus file interface. In-kernel users of
xenbus are assumed to be well-behaved and complete all transactions
before freezing.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41349672e3 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/xen/pvcalls-front.c: In function pvcalls_front_sendmsg:
drivers/xen/pvcalls-front.c:543:25: warning: variable bedata set but not used [-Wunused-but-set-variable]
drivers/xen/pvcalls-front.c: In function pvcalls_front_recvmsg:
drivers/xen/pvcalls-front.c:638:25: warning: variable bedata set but not used [-Wunused-but-set-variable]
They are never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6738028dd5 ]
Command 'perf record' and 'perf report' on a system without kernel
debuginfo packages uses /proc/kallsyms and /proc/modules to find
addresses for kernel and module symbols. On x86 this works for root and
non-root users.
On s390, when invoked as non-root user, many of the following warnings
are shown and module symbols are missing:
proc/{kallsyms,modules} inconsistency while looking for
"[sha1_s390]" module!
Command 'perf record' creates a list of module start addresses by
parsing the output of /proc/modules and creates a PERF_RECORD_MMAP
record for the kernel and each module. The following function call
sequence is executed:
machine__create_kernel_maps
machine__create_module
modules__parse
machine__create_module --> for each line in /proc/modules
arch__fix_module_text_start
Function arch__fix_module_text_start() is s390 specific. It opens
file /sys/module/<name>/sections/.text to extract the module's .text
section start address. On s390 the module loader prepends a header
before the first section, whereas on x86 the module's text section
address is identical the the module's load address.
However module section files are root readable only. For non-root the
read operation fails and machine__create_module() returns an error.
Command perf record does not generate any PERF_RECORD_MMAP record
for loaded modules. Later command perf report complains about missing
module maps.
To fix this function arch__fix_module_text_start() always returns
success. For root users there is no change, for non-root users
the module's load address is used as module's text start address
(the prepended header then counts as part of the text section).
This enable non-root users to use module symbols and avoid the
warning when perf report is executed.
Output before:
[tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP
0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text
Output after:
[tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP
0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text
0 0x1b8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../autofs4.ko.xz
0 0x250 [0xa8]: PERF_RECORD_MMAP ... x /lib/modules/.../sha_common.ko.xz
0 0x2f8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../des_generic.ko.xz
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Link: http://lkml.kernel.org/r/20190522144601.50763-4-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97acec7df1 ]
This strncat() is safe because the buffer was allocated with zalloc(),
however gcc doesn't know that. Since the string always has 4 non-null
bytes, just use memcpy() here.
CC /home/shawn/linux/tools/perf/util/data-convert-bt.o
In file included from /usr/include/string.h:494,
from /home/shawn/linux/tools/lib/traceevent/event-parse.h:27,
from util/data-convert-bt.c:22:
In function ‘strncat’,
inlined from ‘string_set_value’ at util/data-convert-bt.c:274:4:
/usr/include/powerpc64le-linux-gnu/bits/string_fortified.h:136:10: error: ‘__builtin_strncat’ output may be truncated copying 4 bytes from a string of length 4 [-Werror=stringop-truncation]
136 | return __builtin___strncat_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shawn Landden <shawn@git.icu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
LPU-Reference: 20190518183238.10954-1-shawn@git.icu
Link: https://lkml.kernel.org/n/tip-289f1jice17ta7tr3tstm9jm@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6122ed2a4 ]
In the vfs_statx() context, during path lookup, the dentry gets
added to sd->s_dentry via configfs_attach_attr(). In the end,
vfs_statx() kills the dentry by calling path_put(), which invokes
configfs_d_iput(). Ideally, this dentry must be removed from
sd->s_dentry but it doesn't if the sd->s_count >= 3. As a result,
sd->s_dentry is holding reference to a stale dentry pointer whose
memory is already freed up. This results in use-after-free issue,
when this stale sd->s_dentry is accessed later in
configfs_readdir() path.
This issue can be easily reproduced, by running the LTP test case -
sh fs_racer_file_list.sh /config
(https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/fs/racer/fs_racer_file_list.sh)
Fixes: 76ae281f63 ('configfs: fix race between dentry put and lookup')
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa763f1b28 ]
We observed the same issue as reported by commit a8d7bde23e
("ALSA: hda - Force polling mode on CFL for fixing codec communication")
We don't have a better solution. So apply the same workaround to CNL.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0692f0eef ]
If I2C_M_RECV_LEN check failed, msgs[i].buf allocated by memdup_user
will not be freed. Pump index up so it will be freed.
Fixes: 838bfa6049 ("i2c-dev: Add support for I2C_M_RECV_LEN")
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eaeb3b7494 ]
Driver stops producing skbs on ring if a packet with FCS error
was coalesced into LRO session. Ring gets hang forever.
Thats a logical error in driver processing descriptors:
When rx_stat indicates MAC Error, next pointer and eop flags
are not filled. This confuses driver so it waits for descriptor 0
to be filled by HW.
Solution is fill next pointer and eop flag even for packets with FCS error.
Fixes: bab6de8fd1 ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31bafc49a7 ]
In case no other traffic happening on the ring, full tx cleanup
may not be completed. That may cause socket buffer to overflow
and tx traffic to stuck until next activity on the ring happens.
This is due to logic error in budget variable decrementor.
Variable is compared with zero, and then post decremented,
causing it to become MAX_INT. Solution is remove decrementor
from the `for` statement and rewrite it in a clear way.
Fixes: b647d39809 ("net: aquantia: Add tx clean budget and valid budget handling logic")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1396500d67 ]
The devcoredump needs to operate on a stable state of the MMU while
it is writing the MMU state to the coredump. The missing lock
allowed both the userspace submit, as well as the GPU job finish
paths to mutate the MMU state while a coredump is under way.
Fixes: a8c21a5451 (drm/etnaviv: add initial etnaviv DRM driver)
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: David Jander <david@protonic.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a51c6b1f9 ]
Both acpi_pci_need_resume() and acpi_dev_needs_resume() check if the
current ACPI wakeup configuration of the device matches what is
expected as far as system wakeup from sleep states is concerned, as
reflected by the device_may_wakeup() return value for the device.
However, they only should do that if wakeup.flags.valid is set for
the device's ACPI companion, because otherwise the wakeup.prepare_count
value for it is meaningless.
Add the missing wakeup.flags.valid checks to these functions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e66b7cc50 ]
Building with Clang reports the redundant use of MODULE_DEVICE_TABLE():
drivers/net/ethernet/dec/tulip/de4x5.c:2110:1: error: redefinition of '__mod_eisa__de4x5_eisa_ids_device_table'
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:90:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^
drivers/net/ethernet/dec/tulip/de4x5.c:2100:1: note: previous definition is here
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:85:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^
This drops the one further from the table definition to match the common
use of MODULE_DEVICE_TABLE().
Fixes: 07563c711f ("EISA bus MODALIAS attributes support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4523a56115 ]
Currently we will not update the receive descriptor tail pointer in
stmmac_rx_refill. Rx dma will think no available descriptors and stop
once received packets exceed DMA_RX_SIZE, so that the rx only test will fail.
Update the receive tail pointer in stmmac_rx_refill to add more descriptors
to the rx channel, so packets can be received continually
Fixes: 54139cf3bb ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9646f0f5b ]
The gpio-adp5588 driver uses interfaces that are provided by
GPIOLIB_IRQCHIP, so select that symbol in its Kconfig entry.
Fixes these build errors:
../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_handler’:
../drivers/gpio/gpio-adp5588.c:266:26: error: ‘struct gpio_chip’ has no member named ‘irq’
dev->gpio_chip.irq.domain, gpio));
^
../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_setup’:
../drivers/gpio/gpio-adp5588.c:298:2: error: implicit declaration of function ‘gpiochip_irqchip_add_nested’ [-Werror=implicit-function-declaration]
ret = gpiochip_irqchip_add_nested(&dev->gpio_chip,
^
../drivers/gpio/gpio-adp5588.c:307:2: error: implicit declaration of function ‘gpiochip_set_nested_irqchip’ [-Werror=implicit-function-declaration]
gpiochip_set_nested_irqchip(&dev->gpio_chip,
^
Fixes: 459773ae8d ("gpio: adp5588-gpio: support interrupt controller")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
