[ Upstream commit 35306eb238 ]
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa ("af_unix: Allow SO_PEERCRED to work across namespaces.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d88fd1b546 ]
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a69 ("net: phy: bcm7xxx: add support for 28nm EPHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27bf4af69f ]
Currently, the rx vlan filter will always be disabled before selftest and
be enabled after selftest as the rx vlan filter feature is fixed on in
old device earlier than V3.
However, this feature is not fixed in some new devices and it can be
disabled by user. In this case, it is wrong if rx vlan filter is enabled
after selftest. So fix it.
Fixes: bcc26e8dc4 ("net: hns3: remove unused code in hns3_self_test()")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 108b3c7810 ]
Currently, if function adds an existing unicast mac address, eventhough
driver will not add this address into hardware, but it will return 0 in
function hclge_add_uc_addr_common(). It will cause the state of this
unicast mac address is ACTIVE in driver, but it should be in TO-ADD state.
To fix this problem, function hclge_add_uc_addr_common() returns -EEXIST
if mac address is existing, and delete two error log to avoid printing
them all the time after this modification.
Fixes: 72110b5674 ("net: hns3: return 0 and print warning when hit duplicate MAC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0472e95ffe ]
HCLGE_FLAG_MQPRIO_ENABLE is supposed to set when enable
multiple TCs with tc mqprio, and HCLGE_FLAG_DCB_ENABLE is
supposed to set when enable multiple TCs with ets. But
the driver mixed the flags when updating the tm configuration.
Furtherly, PFC should be available when HCLGE_FLAG_MQPRIO_ENABLE
too, so remove the unnecessary limitation.
Fixes: 5a5c909174 ("net: hns3: add support for tc mqprio offload")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78e5b6a67 ]
Bellow HNAE3_DEVICE_VERSION_V3, MAC pause mode just support one
TC, when enabled multiple TCs, force enable PFC mode.
HNAE3_DEVICE_VERSION_V3 can support MAC pause mode on multiple
TCs, so when enable multiple TCs, just keep MAC pause mode,
and enable PFC mode just according to the user settings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 513e605d7a ]
The ixgbe driver currently generates a NULL pointer dereference with
some machine (online cpus < 63). This is due to the fact that the
maximum value of num_xdp_queues is nr_cpu_ids. Code is in
"ixgbe_set_rss_queues"".
Here's how the problem repeats itself:
Some machine (online cpus < 63), And user set num_queues to 63 through
ethtool. Code is in the "ixgbe_set_channels",
adapter->ring_feature[RING_F_FDIR].limit = count;
It becomes 63.
When user use xdp, "ixgbe_set_rss_queues" will set queues num.
adapter->num_rx_queues = rss_i;
adapter->num_tx_queues = rss_i;
adapter->num_xdp_queues = ixgbe_xdp_queues(adapter);
And rss_i's value is from
f = &adapter->ring_feature[RING_F_FDIR];
rss_i = f->indices = f->limit;
So "num_rx_queues" > "num_xdp_queues", when run to "ixgbe_xdp_setup",
for (i = 0; i < adapter->num_rx_queues; i++)
if (adapter->xdp_ring[i]->xsk_umem)
It leads to panic.
Call trace:
[exception RIP: ixgbe_xdp+368]
RIP: ffffffffc02a76a0 RSP: ffff9fe16202f8d0 RFLAGS: 00010297
RAX: 0000000000000000 RBX: 0000000000000020 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 000000000000001c RDI: ffffffffa94ead90
RBP: ffff92f8f24c0c18 R8: 0000000000000000 R9: 0000000000000000
R10: ffff9fe16202f830 R11: 0000000000000000 R12: ffff92f8f24c0000
R13: ffff9fe16202fc01 R14: 000000000000000a R15: ffffffffc02a7530
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
7 [ffff9fe16202f8f0] dev_xdp_install at ffffffffa89fbbcc
8 [ffff9fe16202f920] dev_change_xdp_fd at ffffffffa8a08808
9 [ffff9fe16202f960] do_setlink at ffffffffa8a20235
10 [ffff9fe16202fa88] rtnl_setlink at ffffffffa8a20384
11 [ffff9fe16202fc78] rtnetlink_rcv_msg at ffffffffa8a1a8dd
12 [ffff9fe16202fcf0] netlink_rcv_skb at ffffffffa8a717eb
13 [ffff9fe16202fd40] netlink_unicast at ffffffffa8a70f88
14 [ffff9fe16202fd80] netlink_sendmsg at ffffffffa8a71319
15 [ffff9fe16202fdf0] sock_sendmsg at ffffffffa89df290
16 [ffff9fe16202fe08] __sys_sendto at ffffffffa89e19c8
17 [ffff9fe16202ff30] __x64_sys_sendto at ffffffffa89e1a64
18 [ffff9fe16202ff38] do_syscall_64 at ffffffffa84042b9
19 [ffff9fe16202ff50] entry_SYSCALL_64_after_hwframe at ffffffffa8c0008c
So I fix ixgbe_max_channels so that it will not allow a setting of queues
to be higher than the num_online_cpus(). And when run to ixgbe_xdp_setup,
take the smaller value of num_rx_queues and num_xdp_queues.
Fixes: 4a9b32f30f ("ixgbe: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Feng Zhou <zhoufeng.zf@bytedance.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79a7482249 ]
Both cxgb4 and csiostor drivers run on their own independent Physical
Function. But when cxgb4 and csiostor are both being loaded in parallel via
modprobe, there is a race when firmware upgrade is attempted by both the
drivers.
When the cxgb4 driver initiates the firmware upgrade, it halts the firmware
and the chip until upgrade is complete. When the csiostor driver is coming
up in parallel, the firmware mailbox communication fails with timeouts and
the csiostor driver probe fails.
Add a module soft dependency on cxgb4 driver to ensure loading csiostor
triggers cxgb4 to load first when available to avoid the firmware upgrade
race.
Link: https://lore.kernel.org/r/1632759248-15382-1-git-send-email-rahul.lakkireddy@chelsio.com
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebc69e897e ]
This reverts commit 2d52c58b9c.
We have had several folks complain that this causes hangs for them, which
is especially problematic as the commit has also hit stable already.
As no resolution seems to be forthcoming right now, revert the patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214503
Fixes: 2d52c58b9c ("block, bfq: honor already-setup queue merges")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51bb08dd04 ]
An object file cannot be built for both loadable module and built-in
use at the same time:
arm-linux-gnueabi-ld: drivers/net/ethernet/micrel/ks8851_common.o: in function `ks8851_probe_common':
ks8851_common.c:(.text+0xf80): undefined reference to `__this_module'
Change the ks8851_common code to be a standalone module instead,
and use Makefile logic to ensure this is built-in if at least one
of its two users is.
Fixes: 797047f875 ("net: ks8851: Implement Parallel bus operations")
Link: https://lore.kernel.org/netdev/20210125121937.3900988-1-arnd@kernel.org/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d888eaac4f ]
When building bpf selftest with make -j, I'm randomly getting build failures
such as this one:
In file included from progs/bpf_flow.c:19:
[...]/tools/testing/selftests/bpf/tools/include/bpf/bpf_helpers.h:11:10: fatal error: 'bpf_helper_defs.h' file not found
#include "bpf_helper_defs.h"
^~~~~~~~~~~~~~~~~~~
The file that fails the build varies between runs but it's always in the
progs/ subdir.
The reason is a missing make dependency on libbpf for the .o files in
progs/. There was a dependency before commit 3ac2e20fba but that commit
removed it to prevent unneeded rebuilds. However, that only works if libbpf
has been built already; the 'wildcard' prerequisite does not trigger when
there's no bpf_helper_defs.h generated yet.
Keep the libbpf as an order-only prerequisite to satisfy both goals. It is
always built before the progs/ objects but it does not trigger unnecessary
rebuilds by itself.
Fixes: 3ac2e20fba ("selftests/bpf: BPF object files should depend only on libbpf headers")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/ee84ab66436fba05a197f952af23c98d90eb6243.1632758415.git.jbenc@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a98ae12fb ]
When introducing CAP_BPF, bpf_jit_charge_modmem() was not changed to treat
programs with CAP_BPF as privileged for the purpose of JIT memory allocation.
This means that a program without CAP_BPF can block a program with CAP_BPF
from loading a program.
Fix this by checking bpf_capable() in bpf_jit_charge_modmem().
Fixes: 2c78ee898d ("bpf: Implement CAP_BPF")
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922111153.19843-1-lmb@cloudflare.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51032e6f17 ]
The e100_get_regs function is used to implement a simple register dump
for the e100 device. The data is broken into a couple of MAC control
registers, and then a series of PHY registers, followed by a memory dump
buffer.
The total length of the register dump is defined as (1 + E100_PHY_REGS)
* sizeof(u32) + sizeof(nic->mem->dump_buf).
The logic for filling in the PHY registers uses a convoluted inverted
count for loop which counts from E100_PHY_REGS (0x1C) down to 0, and
assigns the slots 1 + E100_PHY_REGS - i. The first loop iteration will
fill in [1] and the final loop iteration will fill in [1 + 0x1C]. This
is actually one more than the supposed number of PHY registers.
The memory dump buffer is then filled into the space at
[2 + E100_PHY_REGS] which will cause that memcpy to assign 4 bytes past
the total size.
The end result is that we overrun the total buffer size allocated by the
kernel, which could lead to a panic or other issues due to memory
corruption.
It is difficult to determine the actual total number of registers
here. The only 8255x datasheet I could find indicates there are 28 total
MDI registers. However, we're reading 29 here, and reading them in
reverse!
In addition, the ethtool e100 register dump interface appears to read
the first PHY register to determine if the device is in MDI or MDIx
mode. This doesn't appear to be documented anywhere within the 8255x
datasheet. I can only assume it must be in register 28 (the extra
register we're reading here).
Lets not change any of the intended meaning of what we copy here. Just
extend the space by 4 bytes to account for the extra register and
continue copying the data out in the same order.
Change the E100_PHY_REGS value to be the correct total (29) so that the
total register dump size is calculated properly. Fix the offset for
where we copy the dump buffer so that it doesn't overrun the total size.
Re-write the for loop to use counting up instead of the convoluted
down-counting. Correct the mdio_read offset to use the 0-based register
offsets, but maintain the bizarre reverse ordering so that we have the
ABI expected by applications like ethtool. This requires and additional
subtraction of 1. It seems a bit odd but it makes the flow of assignment
into the register buffer easier to follow.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4329c8dc11 ]
commit abf9b90205 ("e100: cleanup unneeded math") tried to simplify
e100_get_regs_len and remove a double 'divide and then multiply'
calculation that the e100_reg_regs_len function did.
This change broke the size calculation entirely as it failed to account
for the fact that the numbered registers are actually 4 bytes wide and
not 1 byte. This resulted in a significant under allocation of the
register buffer used by e100_get_regs.
Fix this by properly multiplying the register count by u32 first before
adding the size of the dump buffer.
Fixes: abf9b90205 ("e100: cleanup unneeded math")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9c587fed6 ]
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92ce2f54c ]
The MTU passed to the DSA driver is the payload size, typically 1500.
However, the switch uses the frame size when applying restrictions.
Adjust the MTU with the size of the Ethernet header and the frame
checksum. The VLAN header also needs to be included when the frame
size it per port, but not when it is global.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe23036192 ]
The datasheets suggests the 6161 uses a per port setting for jumbo
frames. Testing has however shown this is not correct, it uses the old
style chip wide MTU control. Change the ops in the 6161 structure to
reflect this.
Fixes: 1baf0fac10 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83ff01864 ]
Currently we blow up in trace_dma_fence_init, when calling into
get_driver_name or get_timeline_name, since both the engine and context
might be NULL(or contain some garbage address) in the case of newly
allocated slab objects via the request ctor. Note that we also use
SLAB_TYPESAFE_BY_RCU here, which allows requests to be immediately
freed, but delay freeing the underlying page by an RCU grace period.
With this scheme requests can be re-allocated, at the same time as they
are also being read by some lockless RCU lookup mechanism.
In the ctor case, which is only called for new slab objects(i.e allocate
new page and call the ctor for each object) it's safe to reset the
context/engine prior to calling into dma_fence_init, since we can be
certain that no one is doing an RCU lookup which might depend on peeking
at the engine/context, like in active_engine(), since the object can't
yet be externally visible.
In the recycled case(which might also be externally visible) the request
refcount always transitions from 0->1 after we set the context/engine
etc, which should ensure it's valid to dereference the engine for
example, when doing an RCU list-walk, so long as we can also increment
the refcount first. If the refcount is already zero, then the request is
considered complete/released. If it's non-zero, then the request might
be in the process of being re-allocated, or potentially still in flight,
however after successfully incrementing the refcount, it's possible to
carefully inspect the request state, to determine if the request is
still what we were looking for. Note that all externally visible
requests returned to the cache must have zero refcount.
One possible fix then is to move dma_fence_init out from the request
ctor. Originally this was how it was done, but it was moved in:
commit 855e39e65c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Feb 3 09:41:48 2020 +0000
drm/i915: Initialise basic fence before acquiring seqno
where it looks like intel_timeline_get_seqno() relied on some of the
rq->fence state, but that is no longer the case since:
commit 12ca695d2c
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Mar 23 16:49:50 2021 +0100
drm/i915: Do not share hwsp across contexts any more, v8.
intel_timeline_get_seqno() could also be cleaned up slightly by dropping
the request argument.
Moving dma_fence_init back out of the ctor, should ensure we have enough
of the request initialised in case of trace_dma_fence_init.
Functionally this should be the same, and is effectively what we were
already open coding before, except now we also assign the fence->lock
and fence->ops, but since these are invariant for recycled
requests(which might be externally visible), and will therefore already
hold the same value, it shouldn't matter.
An alternative fix, since we don't yet have a fully initialised request
when in the ctor, is just setting the context/engine as NULL, but this
does require adding some extra handling in get_driver_name etc.
v2(Daniel):
- Try to make the commit message less confusing
Fixes: 855e39e65c ("drm/i915: Initialise basic fence before acquiring seqno")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Michael Mason <michael.w.mason@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921134202.3803151-1-matthew.auld@intel.com
(cherry picked from commit be988eaee1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ab8a447bc ]
After commit 05b35e7eb9 ("smsc95xx: add phylib support"), link changes
are no longer propagated to usbnet. As a result, rx URB allocation won't
happen until there is a packet sent out first (this might never happen,
e.g. running just ssh server with a static IP). Fix by triggering usbnet
EVENT_LINK_CHANGE.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 597aa16c78 ]
Multipath RTA_FLOW is embedded in nexthop. Dump it in fib_add_nexthop()
to get the length of rtnexthop correct.
Fixes: b0f6019363 ("ipv4: Refactor nexthop attributes in fib_dump_info")
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 325fd36ae7 ]
The enetc phylink .mac_config handler intends to clear the IFMODE field
(bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the
other fields instead.
For normal operation, the bug was inconsequential, due to the fact that
we write the PM0_IF_MODE register in two stages, first in
phylink .mac_config (which incorrectly cleared out a bunch of stuff),
then we update the speed and duplex to the correct values in
phylink .mac_link_up.
Judging by the code (not tested), it looks like maybe loopback mode was
broken, since this is one of the settings in PM0_IF_MODE which is
incorrectly cleared.
Fixes: c76a97218d ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode")
Reported-by: Pavel Machek (CIP) <pavel@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 540effa7f2 ]
For both local and remote sensors all the supported ICs can report an
"undervoltage lockout" condition which means the conversion wasn't
properly performed due to insufficient power supply voltage and so the
measurement results can't be trusted.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-2-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea1300b9df ]
mptcp_token_get_sock() may return a mptcp socket that is in
a different net namespace than the socket that received the token value.
The mptcp syncookie code path had an explicit check for this,
this moves the test into mptcp_token_get_sock() function.
Eventually token.c should be converted to pernet storage, but
such change is not suitable for net tree.
Fixes: 2c5ebd001d ("mptcp: refactor token container")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7e745f8e9 ]
We should always check if skb_header_pointer's return is NULL before
using it, otherwise it may cause null-ptr-deref, as syzbot reported:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:sctp_rcv_ootb net/sctp/input.c:705 [inline]
RIP: 0010:sctp_rcv+0x1d84/0x3220 net/sctp/input.c:196
Call Trace:
<IRQ>
sctp6_rcv+0x38/0x60 net/sctp/ipv6.c:1109
ip6_protocol_deliver_rcu+0x2e9/0x1ca0 net/ipv6/ip6_input.c:422
ip6_input_finish+0x62/0x170 net/ipv6/ip6_input.c:463
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip6_input+0x9c/0xd0 net/ipv6/ip6_input.c:472
dst_input include/net/dst.h:460 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:76 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ipv6_rcv+0x28c/0x3c0 net/ipv6/ip6_input.c:297
Fixes: 3acb50c18d ("sctp: delay as much as possible skb_linearize")
Reported-by: syzbot+581aff2ae6b860625116@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313bbd1990 ]
Thomas explained in https://lore.kernel.org/r/87mtoeb4hb.ffs@tglx
that our handling of the hrtimer here is wrong: If the timer fires
late (e.g. due to vCPU scheduling, as reported by Dmitry/syzbot)
then it tries to actually rearm the timer at the next deadline,
which might be in the past already:
1 2 3 N N+1
| | | ... | |
^ intended to fire here (1)
^ next deadline here (2)
^ actually fired here
The next time it fires, it's later, but will still try to schedule
for the next deadline (now 3), etc. until it catches up with N,
but that might take a long time, causing stalls etc.
Now, all of this is simulation, so we just have to fix it, but
note that the behaviour is wrong even per spec, since there's no
value then in sending all those beacons unaligned - they should be
aligned to the TBTT (1, 2, 3, ... in the picture), and if we're a
bit (or a lot) late, then just resume at that point.
Therefore, change the code to use hrtimer_forward_now() which will
ensure that the next firing of the timer would be at N+1 (in the
picture), i.e. the next interval point after the current time.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+0e964fad69a9c462bc1e@syzkaller.appspotmail.com
Fixes: 01e59e467e ("mac80211_hwsim: hrtimer beacon")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210915112936.544f383472eb.I3f9712009027aa09244b65399bf18bf482a8c4f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe94bac626 ]
In ieee80211_amsdu_aggregate() set a pointer frag_tail point to the
end of skb_shinfo(head)->frag_list, and use it to bind other skb in
the end of this function. But when execute ieee80211_amsdu_aggregate()
->ieee80211_amsdu_realloc_pad()->pskb_expand_head(), the address of
skb_shinfo(head)->frag_list will be changed. However, the
ieee80211_amsdu_aggregate() not update frag_tail after call
pskb_expand_head(). That will cause the second skb can't bind to the
head skb appropriately.So we update the address of frag_tail to fix it.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210830073240.12736-1-pkshih@realtek.com
[reword comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6fab7af6b ]
Fan speed minimum can be enforced from sysfs. For example, setting
current fan speed to 20 is used to enforce fan speed to be at 100%
speed, 19 - to be not below 90% speed, etcetera. This feature provides
ability to limit fan speed according to some system wise
considerations, like absence of some replaceable units or high system
ambient temperature.
Request for changing fan minimum speed is configuration request and can
be set only through 'sysfs' write procedure. In this situation value of
argument 'state' is above nominal fan speed maximum.
Return non-zero code in this case to avoid
thermal_cooling_device_stats_update() call, because in this case
statistics update violates thermal statistics table range.
The issues is observed in case kernel is configured with option
CONFIG_THERMAL_STATISTICS.
Here is the trace from KASAN:
[ 159.506659] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.516016] Read of size 4 at addr ffff888116163840 by task hw-management.s/7444
[ 159.545625] Call Trace:
[ 159.548366] dump_stack+0x92/0xc1
[ 159.552084] ? thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.635869] thermal_zone_device_update+0x345/0x780
[ 159.688711] thermal_zone_device_set_mode+0x7d/0xc0
[ 159.694174] mlxsw_thermal_modules_init+0x48f/0x590 [mlxsw_core]
[ 159.700972] ? mlxsw_thermal_set_cur_state+0x5a0/0x5a0 [mlxsw_core]
[ 159.731827] mlxsw_thermal_init+0x763/0x880 [mlxsw_core]
[ 160.070233] RIP: 0033:0x7fd995909970
[ 160.074239] Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ..
[ 160.095242] RSP: 002b:00007fff54f5d938 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 160.103722] RAX: ffffffffffffffda RBX: 0000000000000013 RCX: 00007fd995909970
[ 160.111710] RDX: 0000000000000013 RSI: 0000000001906008 RDI: 0000000000000001
[ 160.119699] RBP: 0000000001906008 R08: 00007fd995bc9760 R09: 00007fd996210700
[ 160.127687] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000013
[ 160.135673] R13: 0000000000000001 R14: 00007fd995bc8600 R15: 0000000000000013
[ 160.143671]
[ 160.145338] Allocated by task 2924:
[ 160.149242] kasan_save_stack+0x19/0x40
[ 160.153541] __kasan_kmalloc+0x7f/0xa0
[ 160.157743] __kmalloc+0x1a2/0x2b0
[ 160.161552] thermal_cooling_device_setup_sysfs+0xf9/0x1a0
[ 160.167687] __thermal_cooling_device_register+0x1b5/0x500
[ 160.173833] devm_thermal_of_cooling_device_register+0x60/0xa0
[ 160.180356] mlxreg_fan_probe+0x474/0x5e0 [mlxreg_fan]
[ 160.248140]
[ 160.249807] The buggy address belongs to the object at ffff888116163400
[ 160.249807] which belongs to the cache kmalloc-1k of size 1024
[ 160.263814] The buggy address is located 64 bytes to the right of
[ 160.263814] 1024-byte region [ffff888116163400, ffff888116163800)
[ 160.277536] The buggy address belongs to the page:
[ 160.282898] page:0000000012275840 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888116167000 pfn:0x116160
[ 160.294872] head:0000000012275840 order:3 compound_mapcount:0 compound_pincount:0
[ 160.303251] flags: 0x200000000010200(slab|head|node=0|zone=2)
[ 160.309694] raw: 0200000000010200 ffffea00046f7208 ffffea0004928208 ffff88810004dbc0
[ 160.318367] raw: ffff888116167000 00000000000a0006 00000001ffffffff 0000000000000000
[ 160.327033] page dumped because: kasan: bad access detected
[ 160.333270]
[ 160.334937] Memory state around the buggy address:
[ 160.356469] >ffff888116163800: fc ..
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210916183151.869427-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca465e1f1f ]
If cma_listen_on_all() fails it leaves the per-device ID still on the
listen_list but the state is not set to RDMA_CM_ADDR_BOUND.
When the cmid is eventually destroyed cma_cancel_listens() is not called
due to the wrong state, however the per-device IDs are still holding the
refcount preventing the ID from being destroyed, thus deadlocking:
task:rping state:D stack: 0 pid:19605 ppid: 47036 flags:0x00000084
Call Trace:
__schedule+0x29a/0x780
? free_unref_page_commit+0x9b/0x110
schedule+0x3c/0xa0
schedule_timeout+0x215/0x2b0
? __flush_work+0x19e/0x1e0
wait_for_completion+0x8d/0xf0
_destroy_id+0x144/0x210 [rdma_cm]
ucma_close_id+0x2b/0x40 [rdma_ucm]
__destroy_id+0x93/0x2c0 [rdma_ucm]
? __xa_erase+0x4a/0xa0
ucma_destroy_id+0x9a/0x120 [rdma_ucm]
ucma_write+0xb8/0x130 [rdma_ucm]
vfs_write+0xb4/0x250
ksys_write+0xb5/0xd0
? syscall_trace_enter.isra.19+0x123/0x190
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Ensure that cma_listen_on_all() atomically unwinds its action under the
lock during error.
Fixes: c80a0c52d8 ("RDMA/cma: Add missing error handling of listen_id")
Link: https://lore.kernel.org/r/20210913093344.17230-1-thomas.liu@ucloud.cn
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc74e1ee3 ]
ROCE uses IGMP for Multicast instead of the native Infiniband system where
joins are required in order to post messages on the Multicast group. On
Ethernet one can send Multicast messages to arbitrary addresses without
the need to subscribe to a group.
So ROCE correctly does not send IGMP joins during rdma_join_multicast().
F.e. in cma_iboe_join_multicast() we see:
if (addr->sa_family == AF_INET) {
if (gid_type == IB_GID_TYPE_ROCE_UDP_ENCAP) {
ib.rec.hop_limit = IPV6_DEFAULT_HOPLIMIT;
if (!send_only) {
err = cma_igmp_send(ndev, &ib.rec.mgid,
true);
}
}
} else {
So the IGMP join is suppressed as it is unnecessary.
However no such check is done in destroy_mc(). And therefore leaving a
sendonly multicast group will send an IGMP leave.
This means that the following scenario can lead to a multicast receiver
unexpectedly being unsubscribed from a MC group:
1. Sender thread does a sendonly join on MC group X. No IGMP join
is sent.
2. Receiver thread does a regular join on the same MC Group x.
IGMP join is sent and the receiver begins to get messages.
3. Sender thread terminates and destroys MC group X.
IGMP leave is sent and the receiver no longer receives data.
This patch adds the same logic for sendonly joins to destroy_mc() that is
also used in cma_iboe_join_multicast().
Fixes: ab15c95a17 ("IB/core: Support for CMA multicast join flags")
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2109081340540.668072@gentwo.de
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 356ed64991 ]
Currently if a function ptr in struct_ops has a return value, its
caller will get a random return value from it, because the return
value of related BPF_PROG_TYPE_STRUCT_OPS prog is just dropped.
So adding a new flag BPF_TRAMP_F_RET_FENTRY_RET to tell bpf trampoline
to save and return the return value of struct_ops prog if ret_size of
the function ptr is greater than 0. Also restricting the flag to be
used alone.
Fixes: 85d33df357 ("bpf: Introduce BPF_MAP_TYPE_STRUCT_OPS")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210914023351.3664499-1-houtao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e73dbfda ]
ip_vs_conn_tab_bits may be provided by the user through the
conn_tab_bits module parameter. If this value is greater than 31, or
less than 0, the shift operator used to derive tab_size causes undefined
behaviour.
Fix this checking ip_vs_conn_tab_bits value to be in the range specified
in ipvs Kconfig. If not, simply use default value.
Fixes: 6f7edb4881 ("IPVS: Allow boot time change of hash size")
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bc0bdc5afa upstream.
If the state is not idle then rdma_bind_addr() will immediately fail and
no change to global state should happen.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
To view a mangled src_addr, eg with a IPv6 loopback address but an IPv4
family, failing the test.
This would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
CPU: 1 PID: 32204 Comm: syz-executor.1 Not tainted 5.12.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
__list_add_valid+0x93/0xa0 lib/list_debug.c:26
__list_add include/linux/list.h:67 [inline]
list_add_tail include/linux/list.h:100 [inline]
cma_listen_on_all drivers/infiniband/core/cma.c:2557 [inline]
rdma_listen+0x787/0xe00 drivers/infiniband/core/cma.c:3751
ucma_listen+0x16a/0x210 drivers/infiniband/core/ucma.c:1102
ucma_write+0x259/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xa30 fs/read_write.c:603
ksys_write+0x1ee/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Which is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address build one explicitly on the stack and bind to that as any
other normal flow would do.
Link: https://lore.kernel.org/r/0-v1-9fbb33f5e201+2a-cma_listen_jgg@nvidia.com
Cc: stable@vger.kernel.org
Fixes: 732d41c545 ("RDMA/cma: Make the locking for automatic state transition more clear")
Reported-by: syzbot+6bb0528b13611047209c@syzkaller.appspotmail.com
Tested-by: Hao Sun <sunhao.th@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8646e53633 upstream.
Invoke rseq's NOTIFY_RESUME handler when processing the flag prior to
transferring to a KVM guest, which is roughly equivalent to an exit to
userspace and processes many of the same pending actions. While the task
cannot be in an rseq critical section as the KVM path is reachable only
by via ioctl(KVM_RUN), the side effects that apply to rseq outside of a
critical section still apply, e.g. the current CPU needs to be updated if
the task is migrated.
Clearing TIF_NOTIFY_RESUME without informing rseq can lead to segfaults
and other badness in userspace VMMs that use rseq in combination with KVM,
e.g. due to the CPU ID being stale after task migration.
Fixes: 72c3c0fe54 ("x86/kvm: Use generic xfer to guest work function")
Reported-by: Peter Foley <pefoley@google.com>
Bisected-by: Doug Evans <dje@google.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[sean: Resolve benign conflict due to unrelated access_ok() check in 5.10]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d68bad6d8 upstream.
Windows Server 2022 with Hyper-V role enabled failed to boot on KVM when
enlightened VMCS is advertised. Debugging revealed there are two exposed
secondary controls it is not happy with: SECONDARY_EXEC_ENABLE_VMFUNC and
SECONDARY_EXEC_SHADOW_VMCS. These controls are known to be unsupported,
as there are no corresponding fields in eVMCSv1 (see the comment above
EVMCS1_UNSUPPORTED_2NDEXEC definition).
Previously, commit 31de3d2500 ("x86/kvm/hyper-v: move VMX controls
sanitization out of nested_enable_evmcs()") introduced the required
filtering mechanism for VMX MSRs but for some reason put only known
to be problematic (and not full EVMCS1_UNSUPPORTED_* lists) controls
there.
Note, Windows Server 2022 seems to have gained some sanity check for VMX
MSRs: it doesn't even try to launch a guest when there's something it
doesn't like, nested_evmcs_check_controls() mechanism can't catch the
problem.
Let's be bold this time and instead of playing whack-a-mole just filter out
all unsupported controls from VMX MSRs.
Fixes: 31de3d2500 ("x86/kvm/hyper-v: move VMX controls sanitization out of nested_enable_evmcs()")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20210907163530.110066-1-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f9b68f57c upstream.
KASAN reports the following issue:
BUG: KASAN: stack-out-of-bounds in kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
Read of size 8 at addr ffffc9001364f638 by task qemu-kvm/4798
CPU: 0 PID: 4798 Comm: qemu-kvm Tainted: G X --------- ---
Hardware name: AMD Corporation DAYTONA_X/DAYTONA_X, BIOS RYM0081C 07/13/2020
Call Trace:
dump_stack+0xa5/0xe6
print_address_description.constprop.0+0x18/0x130
? kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
__kasan_report.cold+0x7f/0x114
? kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
kasan_report+0x38/0x50
kasan_check_range+0xf5/0x1d0
kvm_make_vcpus_request_mask+0x174/0x440 [kvm]
kvm_make_scan_ioapic_request_mask+0x84/0xc0 [kvm]
? kvm_arch_exit+0x110/0x110 [kvm]
? sched_clock+0x5/0x10
ioapic_write_indirect+0x59f/0x9e0 [kvm]
? static_obj+0xc0/0xc0
? __lock_acquired+0x1d2/0x8c0
? kvm_ioapic_eoi_inject_work+0x120/0x120 [kvm]
The problem appears to be that 'vcpu_bitmap' is allocated as a single long
on stack and it should really be KVM_MAX_VCPUS long. We also seem to clear
the lower 16 bits of it with bitmap_zero() for no particular reason (my
guess would be that 'bitmap' and 'vcpu_bitmap' variables in
kvm_bitmap_or_dest_vcpus() caused the confusion: while the later is indeed
16-bit long, the later should accommodate all possible vCPUs).
Fixes: 7ee30bc132 ("KVM: x86: deliver KVM IOAPIC scan request to target vCPUs")
Fixes: 9a2ae9f6b6 ("KVM: x86: Zero the IOAPIC scan request dest vCPUs bitmap")
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210827092516.1027264-7-vkuznets@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
