[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae1 ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98c ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0df3c7d7a73d75153090637392c0b73a63cdc24a ]
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98c ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f2ddb128fa20f8441d903285632f2c69e90fae1 ]
The VOP on RK3328 needs to run at a higher rate in order to produce a
proper 3840x2160 signal.
Change to use 300MHz for VIO clk and 400MHz for VOP clk, same rates used
by vendor 4.4 kernel.
Fixes: 52e02d377a ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240615170417.3134517-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4306c047415a227bc72f0e7ba9bde1ccdac10435 ]
STM32MP15xx RM0436 Rev 6 section 46.3 System timer generator (STGEN) states
"
Arm recommends that the system counter is in an always-on power domain.
This is not supported in the current implementation, therefore STGEN should
be saved and restored before Standby mode entry, and restored at Standby
exit by secure software.
...
"
Instead of piling up workarounds in the firmware which is difficult to
update, add "arm,no-tick-in-suspend" DT property into the timer node to
indicate the timer is stopped in suspend, and let the kernel fix the
timer up.
Fixes: 8471a20253 ("ARM: dts: stm32: add stm32mp157c initial support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a95449dd975e2ea6629a034f3e74b46c9634916 ]
The per cpu variable cpu_number1 is passed to xlnx_event_handler as
argument "dev_id", but it is not used in this function. So drop the
initialization of this variable and rename it to dummy_cpu_number.
This patch is to fix the following call trace when the kernel option
CONFIG_DEBUG_ATOMIC_SLEEP is enabled:
BUG: sleeping function called from invalid context at include/linux/sched/mm.h:274
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.0 #53
Hardware name: Xilinx Versal vmk180 Eval board rev1.1 (QSPI) (DT)
Call trace:
dump_backtrace+0xd0/0xe0
show_stack+0x18/0x40
dump_stack_lvl+0x7c/0xa0
dump_stack+0x18/0x34
__might_resched+0x10c/0x140
__might_sleep+0x4c/0xa0
__kmem_cache_alloc_node+0xf4/0x168
kmalloc_trace+0x28/0x38
__request_percpu_irq+0x74/0x138
xlnx_event_manager_probe+0xf8/0x298
platform_probe+0x68/0xd8
Fixes: daed80ed0758 ("soc: xilinx: Fix for call trace due to the usage of smp_processor_id()")
Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@amd.com>
Link: https://lore.kernel.org/r/20240408110610.15676-1-jay.buddhabhatti@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12c3ec878cbe3709782e85b88124abecc3bb8617 ]
Update WiFi SDIO and BT UART related props to better reflect details
about the optional onboard RTL8723DS WiFi/BT module.
Also correct the compatible used for bluetooth to match the WiFi/BT
module used on the board.
Fixes: bc3753aed8 ("arm64: dts: rockchip: rock-pi-s add more peripherals")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-14-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7affb86ef62581e3475ce3e0a7640da1f2ee29f8 ]
UAR0 CTS/RTS is not wired to any pin and is not used for the default
serial console use of UART0 on ROCK Pi S.
Override the SoC defined pinctrl props to limit configuration of the
two xfer pins wired to one of the GPIO pin headers.
Fixes: 2e04c25b13 ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-6-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc0daeccc384233eadfa9d5ddbd00159653c6bdc ]
Add cap-mmc-highspeed to allow use of high speed MMC mode using an eMMC
to uSD board. Use disable-wp to signal that no physical write-protect
line is present. Also add vcc_io used for card and IO line power as
vmmc-supply.
Fixes: 2e04c25b13 ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e43111f52b9ec5c2d700f89a1d61c8d10dc2d9e9 ]
Dan pointed out that Smatch is concerned about this code because it uses
spin_lock_irqsave() and then calls wait_event_lock_irq() which enables
irqs before going to sleep. The comment above the function says it
should be called with interrupts enabled, but we simply hope that's true
without really confirming that. Let's add a might_sleep() here to
confirm that interrupts and preemption aren't disabled. Once we do that,
we can change the lock to be non-saving, spin_lock_irq(), to clarify
that we don't expect irqs to be disabled. If irqs are disabled by
callers they're going to be enabled anyway in the wait_event_lock_irq()
call which would be bad.
This should make Smatch happier and find bad callers faster with the
might_sleep(). We can drop the WARN_ON() in the caller because we have
the might_sleep() now, simplifying the code.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/911181ed-c430-4592-ad26-4dc948834e08@moroto.mountain
Fixes: 2bc20f3c84 ("soc: qcom: rpmh-rsc: Sleep waiting for tcs slots to be free")
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240509184129.3924422-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98a0c4f2278b4d6c1c7722735c20b2247de6293f ]
15 qcom platform DTSI files define an adreno_smmu node.
msm8998 is the only one with adreno_smmu disabled by default.
There's no reason why this SMMU should be disabled by default,
it doesn't need any further configuration.
Bring msm8998 in line with the 14 other platforms.
This fixes GPU init failing with ENODEV:
msm_dpu c901000.display-controller: failed to load adreno gpu
msm_dpu c901000.display-controller: failed to bind 5000000.gpu (ops a3xx_ops): -19
Fixes: 87cd46d68a ("Configure Adreno GPU and related IOMMU")
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/be51d1a4-e8fc-48d1-9afb-a42b1d6ca478@freebox.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ea3fd1eb9869fcdcbc9c68f9728bfc47b9503f1 ]
The critical alarm bit for the local temperature sensor (temp1) is in
bit 7 of register 0x45 (not bit 6), and the critical alarm bit for remote
temperature sensor 7 (temp8) is in bit 6 (not bit 7).
This only affects MAX6581 since all other chips supported by this driver
do not support those critical alarms.
Fixes: 5372d2d71c ("hwmon: Driver for Maxim MAX6697 and compatibles")
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbf7467828cd4ec7ceac7a8b5b5ddb2f69f07b0e ]
Using DIV_ROUND_CLOSEST() on an unbound value can result in underflows.
Indeed, module test scripts report:
temp1_max: Suspected underflow: [min=0, read 255000, written -9223372036854775808]
temp1_crit: Suspected underflow: [min=0, read 255000, written -9223372036854775808]
Fix by introducing an extra set of clamping.
Fixes: 5372d2d71c ("hwmon: Driver for Maxim MAX6697 and compatibles")
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37f7707077f5ea2515bf4b1dc7fad43f8e12993e ]
The hardware only supports a single period length for both PWM outputs. So
atmel_tcb_pwm_config() checks the configuration of the other output if it's
compatible with the currently requested setting. The register values are
then actually updated in atmel_tcb_pwm_enable(). To make this race free
the lock must be held during the whole process, so grab the lock in
.apply() instead of individually in atmel_tcb_pwm_disable() and
atmel_tcb_pwm_enable() which then also covers atmel_tcb_pwm_config().
To simplify handling, use the guard helper to let the compiler care for
unlocking. Otherwise unlocking would be more difficult as there is more
than one exit path in atmel_tcb_pwm_apply().
Fixes: 9421bade07 ("pwm: atmel: add Timer Counter Block PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240709101806.52394-3-u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f58f96d1e2357601c092d85b40a2109cf25ef3 ]
If we fail to call nvme_auth_augmented_challenge, or fail to kmalloc
for shash, we should free the memory allocation for challenge, so add
err path out_free_challenge to fix the memory leak.
Fixes: 7a277c37d3 ("nvmet-auth: Diffie-Hellman key exchange support")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7346e7a058a2c9aa9ff1cc699c7bf18a402d9f84 ]
When the state changes from enabled to disabled, polarity, duty_cycle
and period are not configured in hardware and TIM_CCER_CCxE is just
cleared. However if the state changes from one disabled state to
another, all parameters are written to hardware because the early exit
from stm32_pwm_apply() is only taken if the pwm is currently enabled.
This yields surprises like: Applying
{ .period = 1, .duty_cycle = 0, .enabled = false }
succeeds if the pwm is initially on, but fails if it's already off
because 1 is a too small period.
Update the check for lazy disable to always exit early if the target
state is disabled, no matter what is currently configured.
Fixes: 7edf736920 ("pwm: Add driver for STM32 plaftorm")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240703110010.672654-2-u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1fd37f97808db4fa1bf55da0275790c42521e45 ]
Commit 90f5f7ad4f ("md: Wait for md_check_recovery before attempting
device removal.") explained in the commit message that failed device
must be reomoved from the personality first by md_check_recovery(),
before it can be removed from the array. That's the reason the commit
add the code to wait for MD_RECOVERY_NEEDED.
However, this is not the case now, because remove_and_add_spares() is
called directly from hot_remove_disk() from ioctl path, hence failed
device(marked faulty) can be removed from the personality by ioctl.
On the other hand, the commit introduced a performance problem that
if MD_RECOVERY_NEEDED is set and the array is not running, ioctl will
wait for 5s before it can return failure to user.
Since the waiting is not needed now, fix the problem by removing the
waiting.
Fixes: 90f5f7ad4f ("md: Wait for md_check_recovery before attempting device removal.")
Reported-by: Mateusz Kusiak <mateusz.kusiak@linux.intel.com>
Closes: https://lore.kernel.org/all/814ff6ee-47a2-4ba0-963e-cf256ee4ecfa@linux.intel.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240627112321.3044744-1-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
