[ Upstream commit 44f8bd014a ]
With DDR_CAP_AXI_ID_FILTER quirk, indicating HW supports AXI ID filter
which only can get bursts from DDR transaction, i.e. DDR read/write
requests.
This patch add DDR_CAP_AXI_ID_ENHANCED_FILTER quirk, indicating HW
supports AXI ID filter which can get bursts and bytes from DDR
transaction at the same time. We hope PMU always return bytes in the
driver due to it is more meaningful for users.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c124435e8 ]
Non-Transparent Bridge (NTB) devices (among others) may have many DMA
aliases seeing the hardware will send requests with different device ids
depending on their origin across the bridged hardware.
See commit ad281ecf1c ("PCI: Add DMA alias quirk for Microsemi Switchtec
NTB") for more information on this.
The AMD IOMMU IRQ remapping functionality ignores all PCI aliases for
IRQs so if devices send an interrupt from one of their aliases they
will be blocked on AMD hardware with the IOMMU enabled.
To fix this, ensure IRQ remapping is enabled for all aliases with
MSI interrupts.
This is analogous to the functionality added to the Intel IRQ remapping
code in commit 3f0c625c6a ("iommu/vt-d: Allow interrupts from the entire
bus for aliased devices")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3332364e4e ]
Non-Transparent Bridge (NTB) devices (among others) may have many DMA
aliases seeing the hardware will send requests with different device ids
depending on their origin across the bridged hardware.
See commit ad281ecf1c ("PCI: Add DMA alias quirk for Microsemi
Switchtec NTB") for more information on this.
The AMD IOMMU ignores all the PCI aliases except the last one so DMA
transfers from these aliases will be blocked on AMD hardware with the
IOMMU enabled.
To fix this, ensure the DTEs are cloned for every PCI alias. This is
done by copying the DTE data for each alias as well as the IVRS alias
every time it is changed.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1819ef2e2d ]
Also on am335x we need the swsup quirks for musb.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03856e928b ]
We need swsup quirks for sidle and mstandby for musb to work
properly.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1449458333 ]
Adds USB ID for the eyeTV Geniatech T2 lite to the dvbsky driver.
This is a Geniatech T230C based stick without IR and a different USB ID.
Signed-off-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56b4cd4b7d ]
Intel Visual Compute Accelerator (VCA) is a family of PCIe add-in devices
exposing computational units via Non Transparent Bridges (NTB, PEX 87xx).
Similarly to MIC x200, we need to add DMA aliases to allow buffer access
when IOMMU is enabled.
Add aliases to allow computational unit access to host memory. These
aliases mark the whole VCA device as one IOMMU group.
All possible slot numbers (0x20) are used, since we are unable to tell what
slot is used on other side. This quirk is intended for both host and
computational unit sides. The VCA devices have up to five functions: four
for DMA channels and one additional.
Link: https://lore.kernel.org/r/5683A335CC8BE1438C3C30C49DCC38DF637CED8E@IRSMSX102.ger.corp.intel.com
Signed-off-by: Slawomir Pawlowski <slawomir.pawlowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslawx.kitszel@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10b65e2915 ]
This patch adds a quirk disabling keyboard backlight support for the
Dell Inspiron 1012 and 1018.
Those models wrongly report supporting keyboard backlight control
features (through SMBIOS tokens) even though they're not equipped with
a backlit keyboard. This led to broken controls being exposed
through sysfs by this driver which froze the system when used.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=107651
Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a53ba15d81 ]
Due to a quirky C syntax of declaring pointers to array or function
prototype, existing __type() macro doesn't work with map key/value types
that are array or function prototype. One has to create a typedef first
and use it to specify key/value type for a BPF map. By using typeof(),
pointer to type is now handled uniformly for all kinds of types. Convert
one of self-tests as a demonstration.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191004040211.2434033-1-andriin@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adebb11139 ]
As of commit 648e921888 ("clk: x86: Stop marking clocks as
CLK_IS_CRITICAL"), the cht_bsw_rt5645 driver needs to enable the clock
it's using for the codec's mclk. It does this from commit 7735bce05a
("ASoC: Intel: boards: use devm_clk_get() unconditionally"), enabling
pmc_plt_clk_3. However, Strago family Chromebooks use pmc_plt_clk_0 for
the codec mclk, resulting in white noise with some digital microphones.
Add a DMI-based quirk for Strago family Chromebooks to use pmc_plt_clk_0
instead - mirroring the changes made to cht_bsw_max98090_ti in
commit a182ecd380 ("ASoC: intel: cht_bsw_max98090_ti: Add quirk for
boards using pmc_plt_clk_0") and making use of the existing
dmi_check_system() call and related infrastructure added in
commit 22af29114e ("ASoC: Intel: cht-bsw-rt5645: add quirks for
SSP0/AIF1/AIF2 routing").
Signed-off-by: Sam McNally <sammc@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190917054933.209335-1-sammc@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e81b889329 ]
Intel Cherry Trail Whiskey Cove extcon driver connect USB data lines to
PMIC at driver probing for further charger detection. This causes reset of
USB data sessions and removing all devices from bus. If system was
booted from Live CD or USB dongle, this makes system unusable.
Check if USB ID pin is floating and re-route data lines in this case
only, don't touch otherwise.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
[cw00.choi: Clean-up the minor coding style]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20eee6e5af ]
The `connected` value for wired devices was not properly initialized,
it must be set to `true` upon creation, because wired devices do not
generate connection events.
When a raw client (the Steam Client) uses the device, the input device
is destroyed. Then, when the raw client finishes, it must be recreated.
But since the `connected` variable was false this never happended.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30780d086a ]
With -O3, gcc has found an actual unintialized variable stored
into an mmio register in two instances:
drivers/atm/eni.c: In function 'discard':
drivers/atm/eni.c:465:13: error: 'dma[1]' is used uninitialized in this function [-Werror=uninitialized]
writel(dma[i*2+1],eni_dev->rx_dma+dma_wr*8+4);
^
drivers/atm/eni.c:465:13: error: 'dma[3]' is used uninitialized in this function [-Werror=uninitialized]
Change the code to always write zeroes instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 481a7d154c ]
Add one notifier for udev changes net device name.
Fixes: b6601323ef9e ("net: stmmac: debugfs entry name is not be changed when udev rename")
Signed-off-by: Jiping Ma <jiping.ma2@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 840c90fce6 ]
For high-res (8K) or HFR (4K120) displays, using uncompressed pixel
formats like YCbCr444 would exceed the bandwidth of HDMI 2.0, so the
"interesting" modes would be disabled, leaving only low-res or low
framerate modes.
This change lowers the pixel encoding to 4:2:2 or 4:2:0 if the max TMDS
clock is exceeded. Verified that 8K30 and 4K120 are now available and
working with a Samsung Q900R over an HDMI 2.0b link from a Radeon 5700.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Thomas Anderson <thomasanderson@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55817b340a ]
The commit c18647900e ("iommu/dma: Relax locking in
iommu_dma_prepare_msi()") introduced a compliation warning,
drivers/iommu/dma-iommu.c: In function 'iommu_dma_prepare_msi':
drivers/iommu/dma-iommu.c:1206:27: warning: variable 'cookie' set but
not used [-Wunused-but-set-variable]
struct iommu_dma_cookie *cookie;
^~~~~~
Fixes: c18647900e ("iommu/dma: Relax locking in iommu_dma_prepare_msi()")
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00c0688cec ]
Since net_device.mem_start is unsigned long, it should not be cast to
int right before casting to pointer. This fixes warning (compile
testing on alpha architecture):
drivers/net/wan/sdla.c: In function ‘sdla_transmit’:
drivers/net/wan/sdla.c:711:13: warning:
cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f11421ba4a ]
Atomic operations that span cache lines are super-expensive on x86
(not just to the current processor, but also to other processes as all
memory operations are blocked until the operation completes). Upcoming
x86 processors have a switch to cause such operations to generate a #AC
trap. It is expected that some real time systems will enable this mode
in BIOS.
In preparation for this, it is necessary to fix code that may execute
atomic instructions with operands that cross cachelines because the #AC
trap will crash the kernel.
Since "pwol_mask" is local and never exposed to concurrency, there is
no need to set bits in pwol_mask using atomic operations.
Directly operate on the byte which contains the bit instead of using
__set_bit() to avoid any big endian concern due to type cast to
unsigned long in __set_bit().
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b54ef37b1c ]
Current code use dma_wmb() to ensure Rx/Tx descriptors are visible
to device before writing to doorbell.
However, these dma_wmb() are wrong and unnecessary. Therefore,
they should be removed.
iowrite32be() called from gve_rx_write_doorbell()/gve_tx_put_doorbell()
should guaratee that all previous writes to WB/UC memory is visible to
device before the write done by iowrite32be().
E.g. On ARM64, iowrite32be() calls __iowmb() which expands to dma_wmb()
and only then calls __raw_writel().
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3083124e6 ]
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.
And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63078b6ba0 ]
The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.
We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.
Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd217ee686 ]
It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 306d5acbfc ]
1002 if ((quirks & MT_QUIRK_IGNORE_DUPLICATES) && mt) {
1003 struct input_mt_slot *i_slot = &mt->slots[slotnum];
1004
1005 if (input_mt_is_active(i_slot) &&
1006 input_mt_is_used(mt, i_slot))
1007 return -EAGAIN;
1008 }
We previously assumed 'mt' could be null (see line 1002).
The following situation is similar, so add a judgement.
Signed-off-by: Pan Zhang <zhangpan26@huawei.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b06e46427f ]
If sof_machine_check() fails during driver probe, the IPC
state is not initialized and this will lead to a NULL
dereference at driver unload. Example log is as follows:
[ 1535.980630] sof-audio-pci 0000:00:1f.3: error: no matching ASoC machine driver found - aborting probe
[ 1535.980631] sof-audio-pci 0000:00:1f.3: error: failed to get machine info -19
[ 1535.980632] sof-audio-pci 0000:00:1f.3: error: sof_probe_work failed err: -19
[ 1550.798373] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 1550.798393] Call Trace:
[ 1550.798397] snd_sof_ipc_free+0x15/0x30 [snd_sof]
[ 1550.798399] snd_sof_device_remove+0x29/0xa0 [snd_sof]
[ 1550.798400] sof_pci_remove+0x10/0x30 [snd_sof_pci]
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191218000518.5830-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe4e940f0f ]
A new PID is in use for repaired MobileStudio Pro devices. Add it to the
list of devices that need special-casing in wacom_wac_pad_event.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c07a0254c8 ]
At least on a T100HA an Asus vendor-page usage-code 0xff event is send on
every suspend and again on resume, resulting in the following warning:
asus 0003:0B05:1807.0002: Unmapped Asus vendor usagepage code 0xff
being logged twice on every suspend/resume.
This commit silences the "Unmapped Asus vendor usagepage code ..."
warning for usage-code 0xff to avoid these warnings being logged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f18eca9eb ]
The Acer SW5-012 2-in-1 keyboard dock uses a Synaptics S91028 touchpad
which is connected to an ITE 8595 USB keyboard controller chip.
This keyboard has the same quirk for its rfkill / airplane mode hotkey as
other keyboards with the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds this keyboards USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c62f7cd8ed ]
Without the quirk, joystick shows up as single controller
for both first and second player pads/pins.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 348b80b273 ]
Add multitouch support for LG MELF I2C touchscreen.
Apply the same workaround as LG USB touchscreen.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 122d74fac8 ]
The subpacket scanning loop in rxrpc_receive_data() references the
subpacket count in the private data part of the sk_buff in the loop
termination condition. However, when the final subpacket is pasted into
the ring buffer, the function is no longer has a ref on the sk_buff and
should not be looking at sp->* any more. This point is actually marked in
the code when skb is cleared (but sp is not - which is an error).
Fix this by caching sp->nr_subpackets in a local variable and using that
instead.
Also clear 'sp' to catch accesses after that point.
This can show up as an oops in rxrpc_get_skb() if sp->nr_subpackets gets
trashed by the sk_buff getting freed and reused in the meantime.
Fixes: e2de6c4048 ("rxrpc: Use info in skbuff instead of reparsing a jumbo packet")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9e9555575 ]
Include the size of struct nhmsg size when calculating
how much of a payload to allocate in a new netlink nexthop
notification message.
Without this, we will fail to fill the skbuff at certain nexthop
group sizes.
You can reproduce the failure with the following iproute2 commands:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 1111 group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
ip next del id 1111
Fixes: 430a049190 ("nexthop: Add support for nexthop groups")
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6dd4b4f393 ]
An 'alloc_etherdev()' called is not ballanced by a corresponding
'free_netdev()' call in one error handling path.
Slighly reorder the error handling code to catch the missed case.
Fixes: c100e47caa ("mlxsw: minimal: Add ethtool support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cd021a58c ]
Multicast and broadcast packets can be looped from egress to ingress
pre segmentation with dev_loopback_xmit. That function unconditionally
sets ip_summed to CHECKSUM_UNNECESSARY.
udp_rcv_segment segments gso packets in the udp rx path. Segmentation
usually executes on egress, and does not expect packets of this type.
__udp_gso_segment interprets !CHECKSUM_PARTIAL as CHECKSUM_NONE. But
the offsets are not correct for gso_make_checksum.
UDP GSO packets are of type CHECKSUM_PARTIAL, with their uh->check set
to the correct pseudo header checksum. Reset ip_summed to this type.
(CHECKSUM_PARTIAL is allowed on ingress, see comments in skbuff.h)
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: cf329aa42b ("udp: cope with UDP GRO packet misdirection")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02758cb6da ]
Fix xdp_result initialization in netsec_process_rx in order to not
increase rx counters if there is no bpf program attached to the xdp hook
and napi_gro_receive returns GRO_DROP
Fixes: ba2b232108 ("net: netsec: add XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
